PowerConnect 3548p SNTP and web interface not working

Posted by Force Flow on Server Fault See other posts from Server Fault or by Force Flow
Published on 2012-11-30T15:48:57Z Indexed on 2012/11/30 17:06 UTC
Read the original article Hit count: 259

Filed under:

networking

|

switch

|

subnet

|

dell-powerconnect

I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p.

In the logs, this message appears over and over again:

04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp

172 is the management vlan.

172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address.

The DNS server and the switch are located on different subnets and separated by routers.

I am unable to access the web interface of the switch from the 172.17.x.x subnet.

I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet.

There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch.

I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far.

Any ideas?

© Server Fault or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about switch

Problem connecting a 3Com 2952-Plus switch to a Cisco 3750 switch

as seen on Server Fault - Search for 'Server Fault'
Connected a 3Com 2952-SFP Plus switch to a Cisco 3750 switch via fibre. There is a light on the 3Com end, but nothing at the Cisco end, and no traffic will flow. Have swapped SFP's, have swapped fibre cables, have used a different port on the Cisco, have even swapped the 3Com switch, but still no… >>> More
enable Cisco switch to communicate withe HP switch

as seen on Server Fault - Search for 'Server Fault'
I have one CISCO 2906g and hp 2626 switches i link them by MM fiber optic cable, the problem the cant communicate with each other, i verify there is no problem with cable and JBC's. win i connect other HP switch in the other end it will communicate without any problem, but not with CISCO >>> More
SQL Server database with clustered GUID PKs - switch clustered index or switch to sequential (comb)

as seen on Stack Overflow - Search for 'Stack Overflow'
We have a database in which all the PKs are GUIDs, and most of the PKs are also the clustered index for the table. We know that this is bad (due to the random nature of GUIDs). So, it seems there are basically two options here (short of throwing out GUIDs as PKs altogether, which we cannot do (at… >>> More
Repository pattern - Switch out the database and switch in XML files

as seen on Stack Overflow - Search for 'Stack Overflow'
Repository pattern - Switch out the database and switch in XML files. Hello I have an asp.net MVC 2.0 project and I have followed the Repository pattern. Periodically, I am losing access to the database server so I want to have another mechanism in place (XML files) to continue developing. It is… >>> More
MS SQL Database with clustered GUID PKs - switch clustered index or switch to sequential (comb) GUID

as seen on Stack Overflow - Search for 'Stack Overflow'
We have a database in which all the PKs are GUIDs, and most of the PKs are also the clustered index for the table. We know that this is bad (due to the random nature of GUIDs). So, it seems there are basically two options here (short of throwing out GUIDs as PKs altogether, which we cannot do (at… >>> More