Daily Archives

Articles indexed Friday March 4 2011

Page 1/13 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Installing esx 3.5 on hpblade 460c G7

  - by stillStudent

  I was trying to install ESX 3.5 on hp blade 460c but it fails with error no 'network adapter is detected'. Anybody has work around for this. I also tried to install ESX 4.1, it also had the same problem but in case of 4.1 there is support to add your custom driver while installing. So I added NIC drivers and installation completed successfully. ESX 3.5 installtion does not support adding custom drivers while installing. I can't use ESX 4.1 because it does not support 'license server' configuration and only asks for license file(key). I do not have license keys, I only have vmware license server. That is the reason I have to be with ESX 3.5.

  Read the article

• 'Memory read error',Sever hardware error?

  - by wss8848

  hello I got a error about my server which is running CentOS5.5. MCE 20 HARDWARE ERROR. This is *NOT* a software problem! Please contact your hardware vendor CPU 1 BANK 8 TSC 6ab9ff9745f62 [at 2394 Mhz 9 days 1:50:52 uptime (unreliable)] MISC cf36ad0100081186 ADDR 203376500 MCG status: MCi status: MCi_MISC register valid MCi_ADDR register valid MCA: MEMORY CONTROLLER RD_CHANNELunspecified_ERR Transaction: Memory read error STATUS 8c0000400001009f MCGSTATUS 0 what is the matter? is memory card error or memory controller error?

  Read the article

• SuperMicro BMC on OpenSuSE Linux --cannot access from LAN

  - by Kendall

  Hi, I have an (old) SMC-001 IPMI device on an (old) X6DVL-EG2 motherboard. My problem is that I cannot access the BMC from LAN. I'm also getting some interesting output from ipmitool. First, the setup. I enable Console Redirection in the BIOS, turn BIOS Redirection after POSt to "disabled". I then modprobe'ed for ipmi_msghandler, ipmi_devintf and ipmi_si. I then found ipmi0 under /dev. So far so good. Since I want console redirection over serial, I modified /boot/grub/menu.lst: http://pastebin.com/YYJmhusQ I then modified "/etc/inittab" as follows: S1:12345:respawn:/sbin/agetty -L 19200 ttyS1 ansi Networking I set as following, using "ipmitool" ipaddr: 192.168.3.164 netmask: 255.255.255.0 defgw: 192.168.3.1 The above are correct for my environment. To test it I do: ipmitool -I open chassis power off which responds by powering off the machine. When I to access from another computer on the network, however, I get an error message: host# ipmitool -I lanplus -H 192.168.10.164 -U Admin -a chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status "Admin" seems to be a valid user name: host# ipmitool -I open user list 1 2 Admin true false true USER The interesting output from ipmitool I initially mentioned: host # ipmitool -I open lan set 1 access on Set Channel Access for channel 1 failed: Request data field length limit exceeded Also, newload4:/home/gjones # ipmitool channel info 1 Channel 0x1 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : session-less Active Session Count : 0 Protocol Vendor ID : 7154 Get Channel Access (volatile) failed: Request data field length limit exceeded The output of "ipmitool -I open lan print 1" is here: http://pastebin.com/UZyL6yyE Any help/suggestions is greatly appreciated; I've been working with this thing for a few hours now with no success.

  Read the article

• SQL Server 2008 R2 Enterprise won't install on Windows 2008 R2 Enterprise

  - by Carlos Paulino

  I've been trying to install SQL Server on a new Windows Server 2008. I have tried everything but I haven't been able to narrow down the problem. When the installation fails I get " Exit code (Decimal): -2068643839". The problem with this is that according to Microsoft this is a generic error code. I follow their guide to look into the detail.txt inside C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\ But I can't find something that specifies the exact error. Any suggestions ? Thanks in advanced. I uploaded to detail.txt to http://www.megaupload.com/?d=0MV46SZH because it is to big to paste here. Below is the summary.txt ---------- Overall summary: Final result: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Exit code (Decimal): -2068643839 Exit facility code: 1203 Exit error code: 1 Exit message: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Start time: 2011-02-28 11:29:56 End time: 2011-02-28 11:34:45 Requested action: Install Machine Properties: Machine name: SA-SERVER Machine processor count: 8 OS version: Windows Server 2008 R2 OS service pack: Service Pack 1 OS region: United States OS language: English (United States) OS architecture: x64 Process architecture: 64 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Package properties: Description: SQL Server Database Services 2008 R2 ProductName: SQL Server 2008 R2 Type: RTM Version: 10 SPLevel: 0 Installation location: F:\x64\setup\ Installation edition: ENTERPRISE User Input Settings: ACTION: Install ADDCURRENTUSERASSQLADMIN: True AGTSVCACCOUNT: NT AUTHORITY\SYSTEM AGTSVCPASSWORD: ***** AGTSVCSTARTUPTYPE: Manual ASBACKUPDIR: Backup ASCOLLATION: Latin1_General_CI_AS ASCONFIGDIR: Config ASDATADIR: Data ASDOMAINGROUP: <empty> ASLOGDIR: Log ASPROVIDERMSOLAP: 1 ASSVCACCOUNT: <empty> ASSVCPASSWORD: ***** ASSVCSTARTUPTYPE: Automatic ASSYSADMINACCOUNTS: <empty> ASTEMPDIR: Temp BROWSERSVCSTARTUPTYPE: Disabled CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\ConfigurationFile.ini CUSOURCE: ENABLERANU: False ENU: True ERRORREPORTING: False FARMACCOUNT: <empty> FARMADMINPORT: 0 FARMPASSWORD: ***** FEATURES: SQLENGINE,BIDS,CONN,IS,BC,SDK,SSMS,ADV_SSMS,SNAC_SDK,OCS FILESTREAMLEVEL: 0 FILESTREAMSHARENAME: <empty> FTSVCACCOUNT: <empty> FTSVCPASSWORD: ***** HELP: False IACCEPTSQLSERVERLICENSETERMS: False INDICATEPROGRESS: False INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL Server\ INSTALLSHAREDWOWDIR: C:\Program Files (x86)\Microsoft SQL Server\ INSTALLSQLDATADIR: <empty> INSTANCEDIR: D:\SQLServer INSTANCEID: MSSQLSERVER INSTANCENAME: MSSQLSERVER ISSVCACCOUNT: NT AUTHORITY\SYSTEM ISSVCPASSWORD: ***** ISSVCSTARTUPTYPE: Automatic NPENABLED: 0 PASSPHRASE: ***** PCUSOURCE: PID: ***** QUIET: False QUIETSIMPLE: False ROLE: AllFeatures_WithDefaults RSINSTALLMODE: FilesOnlyMode RSSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE RSSVCPASSWORD: ***** RSSVCSTARTUPTYPE: Automatic SAPWD: ***** SECURITYMODE: SQL SQLBACKUPDIR: <empty> SQLCOLLATION: SQL_Latin1_General_CP1_CI_AS SQLSVCACCOUNT: NT AUTHORITY\SYSTEM SQLSVCPASSWORD: ***** SQLSVCSTARTUPTYPE: Automatic SQLSYSADMINACCOUNTS: SA-SERVER\Administrator SQLTEMPDBDIR: <empty> SQLTEMPDBLOGDIR: <empty> SQLUSERDBDIR: <empty> SQLUSERDBLOGDIR: <empty> SQMREPORTING: False TCPENABLED: 1 UIMODE: Normal X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\ConfigurationFile.ini Detailed results: Feature: Database Engine Services Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: SQL Client Connectivity SDK Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Integration Services Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools Connectivity Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Management Tools - Complete Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Management Tools - Basic Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools SDK Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools Backwards Compatibility Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Business Intelligence Development Studio Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Microsoft Sync Framework Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Rules with failures: Global rules: Scenario specific rules: Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\SystemConfigurationCheck_Report.htm

  Read the article

• Remote Desktop to Virtual Machine

  - by Valvaris

  Hello: I recently reformatted one of my servers with Windows Server 2008 x64 and with that, installed the latest version of VMWare server on it. Within that, I created a new Windows Server 2003 R2 x86 virtual machine for the purposes of being a backup domain controller. I was able to successfully configure it as a domain controller and have it provide DNS service to my domain. I've been using the VMWare remote console to set this up and figured it was time to get remote desktop working. I set it up as I have with many other computers on my network (hitting the checkbox, making the firewall isn't blocking it) and I cannot get remote desktop to connect to it. I've tried using the computer name and its IP address neither work. I can ping the computer from the outside but the Virtual machine cannot ping anything from inside it. All machines are on the same subnet. I can't seem to figure this out.

  Read the article

• Rackspace copy script failure message "java.net.SocketTimeoutException: Read timed out"

  - by user53864

  I am using Rackspace for Ubuntu cloud server. Everyday a script(I guess the script is from rackspace) executes on the cloud servers which copies the backfile to the Rackspace CloudFiles and sends the mail as if the files are copied and I've scheduled the script on the cloud servers. I've no much knowledge of the script and I guess the script is based on Cruise(as I could see build.xml, some jar files ...). Everyday the files are copied to the Rackspace from cloud servers but sometimes don't know why, the files will be copied to Rackspace sending an error failure message or sometimes the files will not be copied and sends the error failure message like the one below. Error while backing up on Station1 on 03/03/2011 04:50 AM and reason for error is java.net.SocketTimeoutException: Read timed out Anybody using Rackspace?, anybody has any fix for this?

  Read the article

• MySQL: how to enable Slow Query Log?

  - by Continuation

  Can you give me an example on how to enable MySQL's slow query log? According to the doc: As of MySQL 5.1.29, use --slow_query_log[={0|1}] to enable or disable the slow query log, and optionally --slow_query_log_file=file_name to specify a log file name. The --log-slow-queries option is deprecated. So how do I use that option? Can I put it in my.cnf? An example would be greatly appreciated. Thank you very much

  Read the article

• IIS7 - Lock Violation error, HTTP handlers, modules, and the <clear /> element

  - by Daniel Schaffer

  I have an ASP.NET site that uses its own set of HTTP handlers and does not need any modules. So, in IIS6, all I had to do was this in my web.config: <httpModules> <clear /> </httpModules> However, if I try to do the same in the system.webServer area for IIS7, I get a 500 error when I try to view the site, and in IIS manager when I try to view the handler mappings, I get a popup box with the message: There was an error while performing this operation Details: Filename: \?\C:\Sites\TheWebSiteGoesHere\web.config Line number: 39 Error: Lock violation Line 39 is where the <clear /> element is. Some googling led me to a solution involving running this command: %windir%\system32\inetsrv\appcmd.exe unlock config -section:system.webServer/modules ...but that did not solve the problem.

  Read the article

• View httpd/lighttpd modules that are installed on shared hosting

  - by sdek

  I don't have access to the httpd.conf file on this shared host, but I wanted to see which modules are enabled/installed. Is there a (easy) way to find out without access to the httpd.conf file? For example, with PHP you can run a file that has phpinfo() in it to get the PHP info. Anything similar? The web server is lighttpd, which I understand is mostly compatible with apache httpd. (And yes, I am going to email the hosting support, but it sure would be nice to know for the future)

  Read the article

• Nginx ssl redirection of images

  - by krishna raj

  Hi. I am trying to set up nginx as reverse proxy for a tomcat server using SSL connection. I want the client's browser to load my tomcat application when nginx reverse proxy's IP is called from client's browser. My tomcat application's address is 192.168.25.25 and nginx proxy's address is 192.168.25.50 In my nginx.conf file i have added these lines # location / { proxy_pass https://192.168.25.25:443/myapp/; proxy_redirect https://192.168.25.25/myapp/ https://192.168.25.25/; } # Some of the images in my application is stored at 192.168.25.25/images/ . Now these directories cant be accessed as the proxy_pass is set to 192.168.25.25:443/myapp. Is there way to access images directory also without changing proxy_pass ? Thanks in advance.

  Read the article

• What Raid should I use for Website Static Files / Content

  - by Simon

  I'm building a Web server (IIS7) and would like to know the best practice for storing static content and the uploaded files of website's users (predominantly pictures, but also other documents like pdf's). I will keep the operating System on a Raid 1 array. Where should I be keeping the actual website's pages & files, it's own static content, and that of it's users? Should I be placing this content on a seperate raid array, and if so which type? I was considering using SLC SSD's (Such as the Intel's X25-e) but the following issues came to light. Will the SLC SSD's give any improvement over a 2.5" 15k SAS Drive for this type of content? If I did use SSD's, I'm under the belief I would still need to use Raid for redundancy, yet I've heard Intel X25-e's don't support TRIM. Does this scrap them as a legitimate option?

  Read the article

• How can I rewrite / redirect URL's in Glassfish V3?

  - by Jin Liew

  Hi, I'd like to simplify the URL's to access a Glassfish V3 application by removing file extensions and otherwise shortening URL's. I've already set my application as the default application, so that there is no need to include the context root in the URL. I'd like to: * Remove file extensions * Shorten the URL to files deep in the folder structure I'd like to do this using pattern matching rather than on a per file basis (Site is small at the moment but will change frequently and grow). Some examples of what I'd like to do: * foo.com/bar.html - foo.com/bar * foo.com/folder1/folder2/bar2.html - foo.com/bar2 Any help would be greatly appreciated. Thanks. Cheers, Jin

  Read the article

• Good experiences with bulk rate SMS providers?

  - by jen_h

  We're a pretty popular service, our users are currently sending 100000+ SMS messages (projected 180k this month, and continuing to grow) per month. We're currently using a primary domestic provider that doesn't provide bulk rates and doesn't provide short code access. We're using a few backup providers as well for max redundancy, but aren't thrilled by 'em. We're ideally looking for a service that provides good bulk rates/incentives, good uptime/redundancy/reputation, easy API-integration (including respectable error codes!) ;). Right now, we're looking primarily for a domestic US SMS solution, but aren't averse to using the same provider for both International & US. For those of you using bulk SMS right now - what are your recommendations, experiences, etc. in the bulk SMS domain? It sounds like I'm looking for a golden unicorn here, I know, but any data/recommendations/warnings you've got are helpful!

  Read the article

• How does Microsoft Word And Excel Run without any installation?

  - by Sathya

  I was having a discussion on bookmarks in Word with a friend, and he suggested me to check out his implementation of a query in Word. Since I did not have Microsoft Word installed, I told him I don't have Word so I won't be able to test it. To this, he mentioned that he'll send the executables and it will work - I argued that without an installation this will fail. I was rather shocked when he sent me the standalone executables and on running them, Word actually launched and I was able to use almost every functionality o_0 How's this possible? I've never installed Microsoft Office on my system, this isn't any "portable" app or VMWare ThinStall ( thanks nhinkle, didn't know about this). There are absolutely no Microsoft Office related files - except for winword.exe and excel.exe. Curiously even Microsoft Excel works fine with just the standalone executable. winword.exe size is about 38 MB, and excel.exe size is just 35kb, which makes it even more strange. I'm running on Windows XP, the files were from Office 2003. I was discussing this on Chat prior to posting, here's the conversation

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• Windows 7: Menu 'New->Text document' is missing, when not admin user

  - by Isamux

  Hi, when I'm logged in as a user that is not member of the administrator group the entry to create a new textfile is missing from the right click "New" menu. If I give the user admin rights or start the explorer with admin rights the "New - text document" menu entry magically appears. As far as I can see the registry entries are correct. Anybody got a solution for that side effect of beeing a normal user in windows?? Regards

  Read the article

• Extracting data from Visual FoxPro databases

  - by whitequark

  I just got some 20Gb of data in a Visual FoxPro database with a custom frontend probably written in the same framework, and need to extract that data in any well-known format. I don't know anything about VFP in particular, but as it is SQL, there should be a way of opening an SQL console, or maybe an vfpdump utility. How can I do that? Everything I have now are a bunch of obscure binary files and a frontend executable.

  Read the article

• Can't set 1280x1024 on Ubuntu with Nvidia Geforce 8400 GS

  - by torbengb

  Ubuntu doesn't offer 1280x1024 but that's what my monitor has -- I want to set that resolution but need help doing so. Ubuntu offers 1360x768, 1152x864, 1024x768 when using the Nvidia driver version 180. This is Ubuntu 9.04 installed as "Wubi" through Windows, I believe it's the amd64 version. Google gave me this precise explanation which is complete latin to me; I'm a Windows guy and not familiar with Terminal. These SU questions also don't provide answers, hence this new question. I hope you can help, and I will provide additional info if required.

  Read the article

• Windows 7: Screen will power of, or blank and lock, but not both.

  - by Heptite

  For some reason, my Windows 7 (Ultimate, 64bit) laptop will not power off the display and keep it off if I have the screen saver and/or the timed auto-lock enabled. Either the display blanks (and locks) but never powers off, or it powers off for less then a minute, then the back light visibly powers back on and stays on, even though the screen remains blanked until I touch a key or the trackpad. I've tried varying the screen power down time to greater than, less than, and exactly equal to the blank screen/lock time, with no success. Turning the screen saver and the timed auto-lock off does allow the timed display power down in the power settings to work properly. (Note that I am not talking about system sleep or hibernate. I'm talking about when the machine remains running, but only the display should power down.)

  Read the article

• Looking for a very bare and basic blog system?

  - by Shedo Chung-Hee Surashu

  Does anyone know of a user-hosted blog which can be an alternative to WordPress only, it should only have the bare necessities of a blog. I'll just take it from there. It should only have the following: Admin Account (for posting, editing, etc) Archive System Posting System with character limitation (For the Read More links.) Accept Comments from other users (only requires the user's name and email and / or website, then the actual comment). Pages (Allows me to create pages for custom content.) The reason I want this is because WordPress is already too bloated up that there are a ton of features that I don't need. I'd mostly be satisfied with a blogging system that has the above feature-set and I'll just work my way to add my own feature as I require it along the way.

  Read the article

• Don't know why this small shell script wont work

  - by tominated

  Hi, I'm trying to make a small script to start up gunicorn for a python website I'm making. I have modified the script found at https://github.com/benoitc/gunicorn/blob/master/examples/gunicorn_rc slightly. Here's my version. #!/bin/sh GUNICORN=/usr/local/bin/gunicorn ROOT=/srv/mobile-site/app PID=/var/run/gunicorn.pid APP=mobilecms:app if [ -f $PID ]; then rm $PID fi cd $ROOT exec $GUNICORN -b 127.0.0.1:8080 -w 8 -k gevent --pidfile=$PID $APP When I try to run the script though, it shows this error /etc/init.d/gunicorn: 13: Syntax error: end of file unexpected (expecting "fi") Does anyone know what's wrong?

  Read the article

• Which is faster, copying everything at once or one thing at a time?

  - by fredley

  I am transferring a bunch (20+) of large (1GB+) files to my external flash drive over USB 2.0. Is it quicker to just sling them all over at once (as in one at a time but not waiting for the previous transfer to finish) so that there are multiple transfers going on, or transfer one, wait for it to finish, transfer the next. The files are coming from a variety of locations so I can't do one single big transfer. Are there any other advantages to one way or the other that are worth considering?

  Read the article

• Searching for a specific option in a man page

  - by mitch_feaster

  I often find myself man'ing a command just to learn about one specific option. Most of the time I can search to the option just fine, unless it's something like ffmpeg or gcc where I have to step through about 40 matches until I get to the actual description of the option... Sometimes I can get lucky and search for the word "options" to get close and then refine it from there, but it would be nice if I could reliably jump straight to the option in question. It would be cool if there was a tool that could parse out the options and build a database on which you could do searches, but after looking at the groff markup for a few pages I've determined it would only be a best-guess effort due to the lack of meta-information in groff markup... In my ideal world woman mode in emacs would support searching for specific options... :) Any tips for jumping straight to a specific option in a man page?

  Read the article

• Any ideas out there as to how the data can be recovered from an SSD?

  - by ben

  A friend had some form of catastrophic failure on an HP mini 1000, unbootable. Of course there was data that wasn't backed up. I've removed the SSD and hooked it up to a ZIF 40 enclosure but can not seem to get the drive to be recognized in Windows 7. In Disk Management it displays as present, but uninitialized. Attempting to initialize it presents an error Virtual Disk Manager - "The device is not ready". There is scant information on MIE (the custom OS), so I'm not even sure what kind of file system I'm dealing with. In any case, if the filesystem is indeed some flavor other than FAT or NTFS, is this error consistent with that? Are there any creative ideas out there as to how the data can be recovered? Update: Thanks for all the suggestions! I hadn't even considered running a live cd. Unfortunately no luck with Ubuntu (live cd) or explore2fs. The zif connection seems ok (color coded green led for proper connect, orange for not). The drive can't be initialized and therefore can't be formatted, so I guess there may be some real damage. Probably needs to head to a specialist. Thanks again for the feedback, much appreciated.

  Read the article

• Prevent Windows Live Mail to download all messages from IMAP

  - by m8t

  Hello, Recently I'm trying the Window Live Mail client. Simple and beautiful. I have set up an IMAP account, and I'm used that a client only downloads headers. However Windows Live Mail automatically creates a list of tasks to download all messages from all directories when you are closing the client. Is it possible to avoid this? It's a good and a bad thing. You can work offline and you have a backup, but it takes extremely long to perform, in fact I have about hundred of thousand of emails. This task can take a whole day to perform. After looking in the settings I don't see anything special, maybe you have an idea? Thank you Mike

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >