Daily Archives

Articles indexed Monday July 1 2013

Page 17/21 | < Previous Page | 13 14 15 16 17 18 19 20 21  | Next Page >

• Remoting into two diffrent servers on the same network

  - by user160605

  I`m trying to figure out a way to remote into both my servers on the same network. I have a 2008 r2 and a server 2003. Right now i can remote into my server 2003 but I dont know what IP to use for the 2k8 server. They seem to have the same public im. Both servers are behind a fire wall (sonic wall tz170) I rememeber having to to something on the firewall to get into the 2k3 server but forgot what I did... Can anyone give some advice thanks

  Read the article

• Out Of Memory Error - Magento

  - by robobobobo

  Ok normally I understand when my server is giving me out of memory errors, but this one has me stumped! I'm running a magento based site, with one or two plugins in it and the rest is pretty basic. The site runs and loads fine wiht no issues. However in the backend - Configuration - Payment Methods it gives me the following out of memory error Fatal error: Out of memory (allocated 39059456) (tried to allocate 85 bytes) in ########/Varien/Simplexml/Element.php on line 84 Now this is where I'm confused..it's allocated more than it tried to allocate? Am I correct there? So how is it running out of memory? My server has 6Gb ram, an SSD and 2 CPU's running WHM with a few other low traffic sites on it. I set my php memory limit to 100mb, 1000mb and finally unlimited but all to no avail! I'm completely lost here, would really appreciate some expertise on this Cheers

  Read the article

• Why Are SPF Records Failing?

  - by robobobobo

  Ok I've been going through various different sites, resources and topics here trying to figure out what is wrong with my SPF records but no matter what I do they don't seem to pass. Here's what I have "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" I've tried multiple different tools to check my spf records, some give me a pass, some don't. But I can't send mail to certain google app accounts, they just bounce back all the time which is very annoying. Anyone got any ideas? I have noticed that the source IP address is not the IPV4 addresses I've defined, but Cpanel wouldn't let me add that address into it.. And here's the result of tests I'm getting back from port25.com. I'm running WHM by the way and have enabled spf and dkim. Summary of Results SPF check: fail DomainKeys check: neutral DKIM check: pass Sender-ID check: fail SpamAssassin check: ham Details: HELO hostname: server1.viralbamboo.com Source IP: 2a01:258:f000:6:216:3eff:fe87:9379 mail-from: ###@viralbamboo.com SPF check details: Result: fail (not permitted) ID(s) verified: smtp.mailfrom=###@viralbamboo.com DNS record(s): viralbamboo.com. SPF (no records) viralbamboo.com. 13180 IN TXT "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" viralbamboo.com. AAAA (no records) viralbamboo.com. 13180 IN MX 0 viralbamboo.com. viralbamboo.com. AAAA (no records) DomainKeys check details: Result: neutral (message not signed) ID(s) verified: header.From=###@viralbamboo.com DNS record(s): DKIM check details: Result: pass (matches From: ###@viralbamboo.com). ID(s) verified: header.d=viralbamboo.com Canonicalized Headers: content-type:multipart/alternative;'20'boundary="4783D1BE-5685-41CF-B91B-1F15E91DD1E3"'0D''0A' date:Mon,'20'1'20'Jul'20'2013'20'21:30:47'20'+0000'0D''0A' subject:=?utf-8?Q?test?='0D''0A' to:"[email protected]?="'20''0D''0A' from:=?utf-8?Q?Rob_Boland_-_Viralbamboo?='20'<###@viralbamboo.com'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=viralbamboo.com;'20's=default;'20'h=Content-Type:Date:Subject:To:From:MIME-Version;'20'bh=CJMO7HYeyNVGvxttf/JspIMoLUiWNE6nlQUg5WjTGZQ=;'20'b=;

  Read the article

• Website ocasionally does not load on first click

  - by tfe

  Today I noticed that my website hosted on a virtual server ocasionally does not load on first click. I click on some link, browser starts loading page but nothing loads and does not not appear any error message (like "connection reset by peer etc). Nothing. When I click the same link again, page loads immediately. The same situation on 2 computers in different browsers. It happends not always, maybe on each 20... or 30 click. Sites from other servers load without this problem. Any ideas what can cause this problem?

  Read the article

• Disable disk caches in AWS EBS for PostgreSQL?

  - by Alexandr Kurilin

  It's my understanding that, without correctly disabling OS-level and drive-level caching, there is a chance that in case of system failure the Write-Ahead Log might not be saved correctly and in fact might get corrupted, possibly preventing data recovery. I've already made sure that wal_sync_method=fdatasync however I was unable to make any configuration changes with hdparm since I get the following: $ sudo htparm -I /dev/xvdf /dev/xvdf: HDIO_DRIVE_CMD(identify) failed: Invalid argument Looks like that option is not available in the kind of setup you get in EC2. Am I missing anything here? Are there any other obvious caches I have to disable to ensure the WAL's safety?

  Read the article

• Route a specific user's traffic via VPN but still allow local networking

  - by wbg

  So, I want to route certain traffic via a VPN connection and the rest via my normal Internet connection. I want to run several different programs and most of them don't support binding to a specific network interface (tun0 in my case). I've managed to send a specific user's traffic via the VPN following the answers given here: iptables - Target to route packet to specific interface? But unfortunately, when I run a server that connects to the Internet and has a web interface running on a local IP (127.0.0.1/192.168.0.*), all the Internet traffic correctly goes via tun0, but I'm unable to connect to the web interface from a local IP as a different user. When I log in as the VPN-ified user, I can access services running on local IPs, but other users/machines can't access any servers I start. Can anyone point me in the right direction?

  Read the article

• Disable "System Memory Testing" via OMSA 6.4.0

  - by EGr

  Is it possible to disable system memory testing via OMSA 6.4.0? I can only find ways to do it using newer versions of OMSA; and I can't even see the setting in 6.4.0. I have quite a few machines that I want to disable this (BIOS) setting on, but I don't want to have to install the new OMSA and reboot. My intentions are to disable the setting so that when the systems are rebooted in the future, they don't need to go through the system memory testing. If it is possible to disable this another way, without OMSA or manually changing the BIOS settings, I would be open to that as well.

  Read the article

• Can't deploy rails 4 app on Bluehost with Passenger 4 and nginx

  - by user2205763

  I am at Bluehost (dedicated server) trying to run a rails 4 app. I asked to have my server re-imaged, specifying that I do not want rails, ruby, or passenger install automatically as I wanted to install the latest versions myself using a version manager (Bluehost by default offers rails 2.3, ruby 1.8, and passenger 3, which won't work with my app). I installed ruby 1.9.3p327, rails 4.0.0, and passenger 4.0.5. I can verify this by typing, "ruby -v", "rails -v", and "passenger -v" (also "gem -v"). I made sure to install these not as root, so that I don't get a 403 forbidden error when trying to deploy the app. I installed passenger by typing "gem install passenger", and then installed the nginx passenger module (into "/nginx") with "passenger-install-nginx-module". I am trying to run my rails app on a subdomain, http://development.thegraduate.hk (I am using the subdomain to show my client progress on the website). In bluehost I created that subdomain, and had it point to "public_html/thegraduate". I then created a symlink from "rails_apps/thegraduate/public" to "public_html/thegraduate" and verified that the symlink exists. The problem is: when I go to http://development.thegraduate.hk, I get a directory listing. There is nothing resembling a rails app. I have not added a .htaccess file to /rails_apps/thegraduate/public, as that was never specified in the installation of passenger. It was meant to be 'install and go'. When I type "passenger-memory-status", I get 3 things: - Apache processes (7) - Nginx processes (0) - Passenger processes (0) So it appears that nginx and passenger are not running, and I can't figure out how to get it to run (I'm not looking to have it run as a standalone server). Here is my nginx.conf file (/nginx/conf/nginx.conf): #user nobody; worker_processes 1; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /home/thegrad4/.rbenv/versions/1.9.3-p327/lib/ruby/gems/1.9.1/gems/passenger-4.0.5; passenger_ruby /home/thegrad4/.rbenv/versions/1.9.3-p327/bin/ruby; include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #gzip on; server { listen 80; server_name development.thegraduate.hk; root ~/rails_apps/thegraduate/public; passenger_enabled on; #charset koi8-r; #access_log logs/host.access.log main; location / { root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # #location ~ \.php$ { # root html; # fastcgi_pass 127.0.0.1:9000; # fastcgi_index index.php; # fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; # include fastcgi_params; #} # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # #location ~ /\.ht { # deny all; #} } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers HIGH:!aNULL:!MD5; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} } I don't get any errors, just the directory listing. I've tried to be as detailed as possible. Any help on this issue would be greatly appreciated as I've been stumped for the past 3 days. Scouring the web has not helped as my issue seems to be specific to me. Thanks so much. If there are any potential details I forgot to specify, just ask. ** ADDITIONAL INFORMATION ** Going to development.thegraduate.hk/public/ will correctly display the index.html page in /rails_apps/thegraduate/public. However, changing root in the routes.rb file to "root = 'home#index'" does nothing.

  Read the article

• Requisite of file.append

  - by Jeff Strunk

  Is it possible to make salt require that a particular file was appended to as opposed to the file merely existing? It seems like I can only require a file state. The source looks like it strips out any method names from a require attribute. In the example below, I only want the foo service to run if my lines have been appended to /etc/security/limits.conf. file.append: - name: /etc/security/limits.conf - text: - root hard nofile 65535 - root soft nofile 65535 foo: service.running: - enable: True - require: - file.append: /etc/security/limits.conf

  Read the article

• SOLVED:Bootloader isn't executable booting XEN PV Guest with virtual-manager

  - by user2284355

  I am going insane with an error I am encountering while trying to install a PV Guest of Debian Wheezy on a Ubuntu Server precise Xen default build with libvirt. The steps I take with virt-manager are the following: 1.Net install via: http://ftp.es.debian.org/debian/dists/stable/main/installer-amd64/ 2.Install process is flawless, installed via VNC over virt-manager 3.When the VM starts I get the following error: Error starting domain: POST operation failed: xend_post: error from xen daemon: (xend.err "Bootloader isn't executable") Most answers i have found on google say that I need to edit the VM's .cfg file and correct the path to pygrub but virt-manager does not seem to create this file (I have searched the entire drive with "find". Another detail is that virsh list --all shows no VMs (Not even dom0) while the command xm list shows all of them. Any help is much appreciated. EDIT: Connected remotely via virsh: virsh -c xen+ssh://user@ip dumpxml vmname Found line: /usr/bin/pygrub ln -s /usr/lib/xen-4.1/bin/pygrub /usr/bin/pygrub Now it works. If anyone can think of a better solution give me a shout. Cheers

  Read the article

• Concurrent users with Quickbooks?

  - by airietis

  I work in a company with 3 people who regularly use the same Quickbooks file. However, they work remotely on different networks. I need to implement a solution that allows all three of us to access Quickbooks at the same time remotely (and each make changes at the same time). We have a spare desktop PC that can be utilized as a server. So, my question is: what is the cheapest and most hassle-free solution to solving this problem? I've considered using application cloud hosting, however, it is very expensive ($40 per user a month) and we are on a tight budget. Is it possible to install Quickbooks on my own server, and have them connect to it remotely? If so, what is the best way to accomplish this? Remote desktop protocol? Or is there a built in feature for this with Quickbooks Premier 2013? EDIT: As MDMarra mentioned, I am looking for a solution that offers true simultaneous access. Will using a dedicated server and having users connect to a VPN be a viable solution?

  Read the article

• Confirm disk is broken when it passes all diagnostics

  - by Halfgaar

  I have a system with a potentially broken disk, but the disk passes all manner of diagnostics. I have been unable to confirm that the disk is broken. What are my options? I could just replace the disk, but because this situation is very similar to another more severe situation I have (long story), I'd like to actually make a proper diagnosis as opposed to randomly binning hardware. The issue and history is this: I had a Debian Linux PC (500 MHz P3) acting as router, nagios and munin. It crashed every couple of weeks. No logs or dmesg could be obtained (because it's an old Compaq that only boots when you configure it as keyboardless, making connecting a keyboard later, once it's booted, impossible). At the time, I just replaced the computer with another Compaq (P4 2.4 GHz) because I thought the hardware was faulty. However, it still crashed every couple of weeks. the difference is that on this computer, I can still SSH into it. It gives all kinds of errors on hda. I'd like to confirm that the disk is broken, but nothing I do confirms this: SMART error logs shows no errors. Normally when a disk starts acting up, SMART my pass, but it still records a read-error in the error log. SMART self-test (smartctl -t long /dev/sda) completes without errors. re-allocated sector count (a tell-tale parameter) has been 31 all its life, even when the disk was still in use in my desktop PC years ago, and it still is. The figure never changed. dd if=/dev/sda of=/dev/null bs=4096 passes with flying colors. What else can I do to assess the health of the drive? Again, this is not about making this router fully functional again, this is a disk forensic question, because it just so happens that I have another server that potentially has the same problem, and knowing the answer to this will possibly help me greatly. For the record, below are logs and such. This is the smartctl -a output: smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3120026A Serial Number: 5JT1CLQM Firmware Version: 3.06 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Mon Jul 1 21:18:33 2013 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 24) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 050 046 006 Pre-fail Always - 47766662 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 10 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 820305 9 Power_On_Hours 0x0032 048 048 000 Old_age Always - 46373 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 605 194 Temperature_Celsius 0x0022 036 065 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x001a 050 046 000 Old_age Always - 47766662 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 6 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 80% 46361 - # 2 Extended offline Completed without error 00% 46358 - # 3 Short offline Completed without error 00% 12046 - # 4 Extended offline Completed without error 00% 10472 - # 5 Short offline Completed without error 00% 10471 - # 6 Short offline Completed without error 00% 10471 - # 7 Short offline Completed without error 00% 6770 - # 8 Extended offline Aborted by host 90% 5958 - # 9 Extended offline Aborted by host 90% 5951 - #10 Short offline Completed without error 00% 5024 - #11 Extended offline Aborted by host 80% 5024 - #12 Short offline Completed without error 00% 3697 - #13 Short offline Completed without error 00% 237 - #14 Short offline Completed without error 00% 145 - #15 Short offline Completed without error 00% 69 - #16 Extended offline Completed without error 00% 68 - #17 Short offline Completed without error 00% 66 - #18 Short offline Completed without error 00% 49 - #19 Short offline Completed without error 00% 29 - #20 Short offline Completed without error 00% 29 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the dmesg error when it has crashed (which repeats for a bunch of different sectors): [1755091.211136] sd 0:0:0:0: [sda] Unhandled error code [1755091.211144] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1755091.211151] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 08 fe ad 38 00 00 08 00 [1755091.211166] end_request: I/O error, dev sda, sector 150908216

  Read the article

• IIS 7 with PHP in Domain with Windows Authentication

  - by Michal Saiyan Hajdony

  I have Windows Server 2008 R2 x64b installed with IIS 7, PHP 5.5. This server is added to domain exampledomain , so I have win authentication enabled and all others disabled. I left the two default providers NTLM and negotiate, I granted IIS_IUSRS read access to wwwroot. So far it has worked for me only as I am added to the Administrators group which has read/write access to wwwroot folder. Yet, when someone else is trying to connect, he gets a credentials window and when he puts the domain name and password he cannot get access to the page. The issue is solved when I add read permission to "Domain users" - then all works fine. BUT. My issue is that if one opens windows explorer and types \\servername\wwwroot one can see the files and read them. I have never configured IIS before so I know I miss some really important thing. How can I solve the file visibility problem?

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• Cloning OpenVZ container

  - by Tiffany Walker

  I have an OpenVZ container on 1 host and I would like to clone it over to my server. both run SolusVM. I only have root access to my server and would like to host the container on my server now. Can I use rsync to clone the drive while the OS is running on both? Using a command like this: rsync -uazPx --exclude='/boot' --exclude='/proc' --exclude='/dev' --exclude='/lib' --exclude='/tmp' --exclude='/var/lock' / [email protected]:/ Is there any other areas I should probably not copy over?

  Read the article

• Recommendation for PHP-FPM pm.max_children, PHP-FPM pm.start_servers and others

  - by jaypabs

  I have the following server: Intel® Xeon® E3-1270 v2 Single Processor - Quad Core Dedicated Server CPU Speed: 4 x 3.5 Ghz w/ 8MB Smart Cache Motherboard: SuperMicro X9SCM-F Total Cores: 4 Cores + 8 Threads RAM: 32 GB DDR3 1333 ECC Hard Drive: 120GB Smart Cache: 8MB I am using ubuntu 12.04 - nginx, php, mysql with ISPConfig 3. Under ISPConfig 3 website settings: I have this default value: PHP-FPM pm.max_children = 10 PHP-FPM pm.start_servers = 2 PHP-FPM pm.min_spare_servers = 1 PHP-FPM pm.max_spare_servers = 5 PHP-FPM pm.max_requests = 0 My question is what is the recommended settings for the above variable? Because I found some using a different settings.

  Read the article

• Shaping with shorewall complex shaper not work (or I don't understand principle of operation)

  - by strangeman

  I have router (Debian 6) with 2 network interfaces (and 1 virtual tun interface): eth0 - localnet, 192.168.1.0/24, router ip is 192.168.1.1 eth1 - internet tun0 - openvpn to central office. openvpn network - 10.1.0.0/24, central office network - 192.168.0.0/24 I need shape all traffic, which moves 192.168.1.0/24-192.168.0.1:6666 and 192.168.1.0/24<-192.168.0.1:6666, and restrict its speed to 200kbit. Now, I have this configuration, but its not work: tcdevices (set up interface parameters) #INTERFACE IN-BANDWITH OUT-BANDWIDTH eth0 100mbit 100mbit #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE tcrules (mark all traffic, which move on 6666 port) #MARK SOURCE DEST PROTO PORT(S) 1 0.0.0.0/0 0.0.0.0/0 tcp 6666 #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE tcclasses (shape all marked traffic) #INTERFACE MARK RATE CEIL PRIORITY OPTIONS eth0 1 200kbit 200kbit 2 eth0 255 9*full/10 full 1 default #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE Where is my mistake?

  Read the article

• Tuning OpenVZ Containers to work better with Java?

  - by Daniel

  I have a 8 GB RAM Server (Dedicated) and currently have KVM Virtual Machines running on there (successfully) however i'm considering moving to OpenVZ as KVM seems a bit overkill with a lot of overhead for what i use it for. In the past i have used OpenVZ Containers, hosted by myself and from other providers and Java doesn't seem to work well with them.. One example is that if i give a container 2 GB RAM ( No burst) (with or without vswap doesn't matter) a java instance can only be tuned to use at very most 1500 MB of that RAM (-Xmx, -Xms). Ideally, i wish to be able to create "Mini" containers with about 256MB, 512MB, 768 RAM and run some java instances in them. My question is: I'm trying to find an ideal way to tune a OpenVZ container configuration to work better with Java memory. Please, don't suggest anything related to Java settings, i'm looking for OpenVZ specific answers.. Though i welcome any suggestion if you feel it may help me. Much Appreciated, Daniel

  Read the article

• Unable to connect to second name of Windows 2008 Server R2 machine from XP

  - by Tumba

  I used the command netdom computername /add:newname.domainname.com to add a second name to a server running Windows 2008 Server R2. After restarting the server, I had DNS "A" entries for both names. In addition, the second name was added to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters\OptionalNames, which I believe should have taken care of any NetBIOS resolution. From my Windows 7 workstation, I can ping both names and running net view on both names reveals the same list of resources. From Windows XP, I can ping both names, but net view only works on the first name. Running net view on the second name returns: System error 52 has occurred. You were not connected because a duplicate name exists on the network. Go to System in Control Panel to change the computer name and try again. What do I need to do to make the second name usable from XP clients? Update: I was able to resolve the problem by adding the REG_DWORD key DisableStrictNameChecking = 1 to HKLM\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters, then restarting the Server service. However, I do not understand why this was necessary.

  Read the article

• IIS 7.5 FTP IIS Manager Users Login Fail (530)

  - by Jim

  IIS 7.5 FTP IIS Manager Users Login Fail (530) I'm trying to set up a FTP site on IIS 7.5 that allows IIS Manager Users to login. I'm following this guide: http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/. After set up, I cannot login to the FTP using an IIS Manager User account. The client error I got was 530 User cannot log in. Win32 error: Unspecified error. Error details: An error occured during the authentication process. I tried both with or without a virtual host. A Windows account login fine. The only strange thing I noticed was that when setting up Read permission for Network Service, there was an access denied error when setting up permission for "%SystemDrive%\Windows\System32\inetsrv\config\schema". Any thoughts? Thanks!

  Read the article

• Hardware recommendations for building an Ubuntu encrypted file server

  - by Robert Mashlan

  I would like to build a file server for my home network using Ubuntu. It will serve files from RAID1 configured disks, either in the OS or in hardware. It will be connected to a Gigabit ethernet LAN. The disks will use an encrypted file system. It will serve samba shares. I would like a recommendation on what kind of processing power/memory I would need to build a box that would be able to sustain the full capacity of the Gigabit ethernet connection in a file transfer for a single connection with the overhead of serving from an encrypted disk. I'm not looking to build a dream server, I just want enough processing capacity for high performance (and reliable) file sharing and spend as little as possible for it. This may be tangential, but what kind of hardware would I need to have a server be able to reliably go into a low power mode when no requests are being made of it?

  Read the article

• Python to see if a file falls into a date range

  - by tod

  I have a script that I want to have an if statement check if a file falls between several specified date periods as it searches directories. I have been able to get the time in %Y-%m-%d format for the file, but I can't seem to be able to specify a date range for python to go through. Any ideas/help? Here's what I have so far for name in files: f = os.path.join(root, name) dt = os.path.getmtime(f) nwdt = time.gmtime(dt) ndt = time.strftime('%Y-%m-%d', nwdt)

  Read the article

• Is there any way to search within OneNote 2007 attachments

  - by jtolle

  I'm starting to use OneNote (2007) more. One thing I'd like to do is take notes on papers I have read. That is, I attach, say, a PDF file, and then type in some notes about it. Sometimes I do other stuff like copy some key text or figures from the paper, so OneNote is great for this because all that plus my own notes plus the file itself can all be in one place. However, the OneNote search doesn't seem to be able to search within said PDF files. Windows search finds things, but just in the OneNote cache, not the actual Onenote .one files. (Presumably that will only work for recently accessed stuff, and in any case doesn't take me to my actual notes.) Is there a way to do what I want? If not, does anyone have a suggestion (or link) as to how to best use OneNote to store (and later search for!) this kind of content and notes?

  Read the article

• How to stabilize a disconnecting internet connection?

  - by All

  My internet connection is very interrupting, but it is not sensible for web surfing, as the connection dies for a few seconds and everything is OK. The IP is NOT changing, and just a halt in data transfer. However, it is very annoying for applications needing contact connection like SSH. Since it seems disconnection, SSH closes. Is there any way to stabilize this kind of interrupting connection to keep the connection with zero transfer data to persevere any connection like SSH? I am using Linux (Debian/Ubuntu).

  Read the article

• Linux - Multiple service statuses with one command

  - by Jimbo

  I'm trying to retrieve a list of multiple service statuses in Unix. I'm using the service command: man page. The statuses all start with the transmission-daemon string, for example. I require the ability to list multiple services' statuses, with a single command. Here is what I'm currently trying (and failing) with: Here I'm trying to grab a list of statuses using grep. service $(ls /etc/init.d | grep "transmission-daemon") status Here I'm trying to list all statuses, and then grep for them. service --status-all | grep "transmission-daemon" This produces the following, which isn't much help: How can I effectively achieve what I require with a single command, so that I can then continue piping to awk for further customisation? Desired example output: transmission-daemon started transmission-daemon2 stopped transmission-daemon3 started

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21  | Next Page >