Monthly Archives

Articles indexed in March 2012

Page 61/239 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

• DRBD Not syncing between my nodes

  - by Mike Curry

  Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• How to preserve sysprep from changing Default User settings

  - by user33794

  I'm having diffculties configuring 20 new Dell Vostro minis here. I set up one of them with my preferred OS, applications and settings, especially the Visual Effects Settings of Windows XP. I set them to best performance and deactivated everything else in the box. I copied this profile to Default User Profile and did sysprep -mini -reseal. After capturing this image and deploying it again, the desktop settings are correct except the visual effects settings. fading and everything else is reenabled for each new user which is created on the system. How do I preserve my settings from being overwritten by sysprep? thanks!

  Read the article

• Setting up sound on a LTSP server

  - by hfranco

  I've got a Fedora 13 server setup and running successfully. Unfortunately I'm having issues making sure the clients can hear sound. I've installed the necessary alsa packages but I'm not having any luck. # rpm -qa | grep alsa alsa-oss-1.0.17-4.fc12.x86_64 alsa-lib-1.0.23-1.fc13.x86_64 alsa-utils-1.0.23-3.fc13.x86_64 alsa-oss-libs-1.0.17-4.fc12.x86_64 alsa-plugins-pulseaudio-1.0.22-1.fc13.x86_64 Any idea what I should be looking at?

  Read the article

• Plugin 'InnoDB' registration as a STORAGE ENGINE failed. On win 7

  - by NimChimpsky

  I have had to reinstall MySQL, however the service is failing to start with the above cause listed in evnt viewer. One solution is apparently to delete a couple of files prefixed with 'ib_logfile' which represent any old databases. However I do not have these files, and my service is still failing to start ... ? When I say I don't have these files I did a search using the windows search with zero results, and they are definitely not present in my mysql install directory. And I don't have the "documents and setting/appilcation data' folder referenced in link. In fact I only have only one mysql install directory, I know where that is - what do I need to delete/change ? The instance is configured OK, I ran that as administrator and it is listed in services, but the service itself fails to start Any tips, other than going over to postgresql ?

  Read the article

• What are some hosted MySQL solutions?

  - by bigmac

  I would like to host a MySQL database somewhere. The basic solution would be to get a VPS, but then I am stuck doing all the sysadmin stuff. It's not terribly difficult if you are not doing anything fancy, but if something goes wrong (like a security breach), it may be hard to resolve or even diagnose in the first place. On the other end of the spectrum, I found Xeround and Amazon RDS. Xeround is not exactly standard MySQL. Amazon seems a bit complex to get started (which is weird because they specifically say it is "simple to deploy"). Why is there nothing in the middle? Is there no demand for a basic hosted MySQL solution?

  Read the article

• How can I see which applications have accessed a certain file within a given time period on Linux?

  - by Nikolaidis Fotis

  Is it possible on Linux to find out which applications have accessed a certain file in the last 24 hours? I've come with a few possible solutions: Watch lsof. It works, but it's constrained to watch's granularity. inotify sounds good... but no information of the application accessing the file is provided. auditd may be useful, but I haven't checked that yet. What ways can I see which applications have accessed a certain file within a given time period?

  Read the article

• Outlook users connected to exchange can email from other email accounts

  - by Sherriffwoody

  We have found an issue on our systems whereby an outlook user (both 2007 and 2010) connected to our Exchange server (2007) can send emails as other users using the following steps Within Outlook Click <New Email> Select the <From> button to show a list of accounts outlook contains, but it also shows the option Select<Other Email Address>. This brings up a small dialog box with another button which when selected allows the user to select an email from their contacts or the Active Directory. The user in most cases can select any email within the Active Directory and send an email as if it were coming from that selected email. It seems not everyone has this ability and I'm guessing it is something to do with settings in exchange or AD(version 6) or is there a group policy that can be implemented to stop users being able to do this. We have no idea what allows this and I have failed to find anything using Dr Google. No one has setup delegates within outlook but it does seem to be something similar? Does anyone know how to lock this down? Thanks in advance

  Read the article

• Laptop as server [closed]

  - by Parhs

  My client wants to use a cheap AMD E-300 ,5400 rpm disk,4gb memory laptop as a POS server and music player at the same time with dual screen. I couldnt convince him that this wouldnt be a good choice. The applications are a database a music player ,and the .net 4 application. I am afraid of performance issues. However the reasons for this choice is that laptop takes not much space ,easy dual screen for music player and application ,can easilly be replaced and that it will last forever as none of his laptops are ever broken. I believe that this is a good idea but i feel thats something wrong there. Do you believe that is an ok choice?

  Read the article

• How to check for the existence of a response header in Nginx rules?

  - by Victor Welling

  Setting up the rewriting rules for the request proved to be quite easy in Nginx. For the response, not so much (at least, not for me). I want to strip the Content-Type header from the response if the Content-Length header of the response isn't set. I have the NginxHttpHeadersMoreModule installed, so that should allow me to remove the header, but I can't seem to find a way to check for the existence of the Content-Length header of the response using a rule in Nginx's configuration. Any suggestions on how to do this would be most appreciated!

  Read the article

• Outlook receives winmail.txt attachment instead of Excel, PowerPoint or Word attachments from Lotus notes senders

  - by Philippe

  Ok so the title pretty much says it all. We are offering a Hosted Exchange solution for our customer. Everything is working fine except for one customer complaining that he is receiving winmail.dat or winmail.txt attachments instead of the actual Word Excel or PowerPoint attachments he should be receiving, only when these messages come from a specific European senders, that is using Lotus Notes. I know that usually the problem is coming from Outlook senders to other mail clients, but this is not the first they inform me of this but I can't find anything on the matter so far. Has anyone ever gotten and solved this problem? If not, does anyone have any idea regarding this? I had solved this problem a few months ago, by upgrading Outlook to SP2 and then uninstalling it using the Service Pack removing tool of Microsoft. It seems that only the latest SP1 version could work but not the SP2. The problem is that now nothing is working at all. Thank you for your help, Philippe

  Read the article

• Is there a way to copy the file paths of ALL active windows' opened files?

  - by frenchglen

  The context of this question, is here. I actually know the answer to my question is yes - like I say in my context, this program can do it (somehow). So the really question is, how can I do it. What code do I put in a simple batch file? (or do I have to compile a tiny c++ exe? and run that exe in the batch file?) Might this code be a solution? (.....EnumDesktopWindows?) To clarify, I know that there's e.g. NirSoft OpenedFilesView which shows allll the technically-opened files in Windows, but it's just the 'visible' user-opened ones that I'm after (whatever you can see in Task Manager's Applications tab). Thanks.

  Read the article

• Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

  - by Andrew

  My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

  Read the article

• Restoring open software after a restart event in windows

  - by Doltknuckle

  I find that at the end of a long day, I sometimes have a large number of programs running. All which I will need to use tomorrow. Normally, this isn't an issue, I can simply lock the machine and come back tomorrow. My problem arrises when windows update launches in the middle of the night and force restarts my computer. That in turns closes all my open software. I of course save everything regularly so I don't loose anything, but I waste time reopening all of those resources whenever there is a restart. [EDIT] I should clarify that I still want to be able to restart my computer when an update comes down. Preventing the restart only delays the problem until later. I should have been more specific in that I want to be able to recover my working environment after a restart for any reason. Things like scheduled maintence, power loss, updates, and software installs. [EDIT] I can't simply have them setup to launch at startup becasuse those files change from week to week. So I need something that monitors what I have open, and gives me the option to "recover" those software sessions when I log back in. Anyone have any suggestions on what I can do? I'd even be willing to purchase software to do this for me if that is the only option. Thanks

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• How to establish the real-time communication between Shopping cart running MySQL and Internal System Running PostgreSQL [closed]

  - by Andrew

  I am thinking about the way of establishing some-sort of real-time connection between MySQLpowered shopping cart and internal system that is running on PostgreSQL. Could you give me some sort of insight on this topic? For example, I can write some sort of csv export application, then enable remote MySQL for over the internet connection and then import csv to mysql directly from PC. Or upload csv and run cron on server. But this way of import-export causing delays; so I would like to link databased (or some msort). I have never done it before and would like to hear some opinions about this. Another way "just a thought" might to implement triggers that would initiate the update process via csv; but again, I would like to avoid csv. Do you have any good advise? Maybe some specific examples?

  Read the article

• Can Windows 7 Jump Lists be made to behave like menus when dragged out with a mouse?

  - by FocusStealer

  On a traditional menu, if you mousedown on the menu title, drag down, then release on a menu item, it will trigger that menu item immediately, e.g. in Notepad: Left mouse button down on File Drag down to New Release mouse button will start a new file without requiring an additional click. However, when dragging out a Jump List on Windows 7, you must additionally click the desired item to launch it. Is there any way to change this behavior?

  Read the article

• How to use supervisord to run a PHP script as a daemon?

  - by Alasdair

  I need to have 8 threads of the same PHP script running in the background on a server continuously (as a daemon), and each script need to be automatically restarted if it exits for any reason. I've been advised to use supervisord to do this, but I don't at all understand their documentation, which seems very complicated to me. I also want each of the 8 threads of the script to be initially started at 2 minute intervals (2 minutes in between each launch) but then after this all 8 threads of the same PHP script should continue running on the server forever (and restarting if any exit for any reason). Could someone please explain how to do this with supervisord, or any other easy way of doing it? I'm on CentOS 6. Thank you!

  Read the article

• Adobe Acrobat Pro 9.0 on Windows 7 print to network share gives error

  - by Archit Baweja

  I've recently upgraded a client's workstations to brand new computers, with Windows 7 Professional. The server is still Windows Server 2003. The server has 2-3 file shares that get mapped to users' workstations as drives. The client has also upgraded from Acrobat 6.0 to 9.0 Pro. Since the upgrade, when the client tries to print to the Adobe PDF printer (aka convert something to PDF via the printer interface), it gives an error in the queue if the file is being saved on the network drive. If I instead provide a local path, the file "prints" fine. Additionally, if I change the Adobe PDF printer's settings to "don't spool, print directly to printer", it prints to the network share fine, but then it resets that setting every time. Things I've checked for: Permissions on the network share. The user and the computer has full access. We even gave the "Everyone" ibject full access. Reinstall Adobe Acrobat Pro 9.0 Run updates to upgrade to 9.3.4 Has anyone else bumped into such a problem? The support fellows from Adobe are just taking me around in circles. They don't seem to have a clue either.

  Read the article

• Wireless and Wired Network Access at same time?

  - by grasper

  At work, I use a laptop. It is a Dell Latitude D630 with Windows XP. I work in a lab environment where I need to use the Ethernet Port as a Static IP to interact with a local network (which cannot talk to the outside world). What I would like to do is use the Wireless as the internet connection so i can check email, etc at the same time I am using the ethernet network... It seems like this is not possible. Is there a piece of software or a way to configure it to allow me to do this?

  Read the article

• Shortcuts that make using Windows easier? [closed]

  - by ekaj

  Over the years I have found out a good bit of shortcuts, all of which make using Windows that much faster and easier. I was wondering if I had missed any important ones, or ones that just saved any time. I tried to keep these relative to Windows only, as programs such as Mozilla, Photoshop, etc. bring in hundreds of other shortcuts, which do not apply to all users. These are the current ones I know: For the mouse: Scroll wheel - opens a link in IE into a new tab - closes a specific tab in IE when closed on Right click-n-drag - nifty menu to make a copy of a file or create a shortcut For the keyboard: Cntrl + Alt + Del - need this be explained? WinKey + R - opens 'Run..' WinKey + D - shows the desktop WinKey + E - opens 'My Computer' WinKey + F - opens 'Find..' WinKey + Tab - cool way to switch inbetween windows WinKey + L - locks the computer Alt + Tab - switches windows with a simple interface Alt + F4 - closes windows Alt + F - opens 'File' (Handy for things like IE if you have the menubar disabled) Cntrl + F - find text on current document Cntrl + W - closes a window, or current active tab in IE (or IE itself if only one tab) Cntrl + C - copies selected text / image Cntrl + V - pastes selected text / image So does anyone know of any more shortcuts that just make life easier? I would be much appreciative of any, and I am sure that some other users would like to know some too =]

  Read the article

• Excel help vlookup

  - by user123953

  I need a little help with some excel Employee Locations Hours OT Mr.One Station 1 40 6 Mrs.Seven Station 2 30 6 Mr.Two Station 3 30 4 Mr.Three Station 4 40 4 Mrs.Eight Station 1 32 6 Mr.Four Station 2 32 7 Mrs.Nine Station 3 40 6 Mr.Five Station 4 40 7 Mr.Six Station 1 25 2 Mrs.Ten Station 2 40 3 Mr.Eleven Station 3 60 1 I have spreadsheet with to worksheets one is the data sheet (shown above) on the other sheet is a summary, that has the Locations column as data validation list. I wanna use the data validation list to pull all the people and info from a specific location. I tried using a vlookup put I only know how to use to pull one person at a time not a group of specific to a location.

  Read the article

• suddenly can't connect to Windows 7 PC from xbmc

  - by Damon

  I have xbmc installed on a softmodded classic xbox and all of a sudden I cannot connect to the shared folders on my Windows 7 PC. Well, it can connect but it wants a username and password, but none exist on my computer. It's been several weeks since I last used it, but it was working fine then! and no particular changes I can think of aside from I guess a few Windows updates. I've seen reference online to Windows Live essentials causing issues with file sharing, but I don't even have that installed. And I made sure to tick 'turn off password protected sharing' in my advanced network setup. I had the guest account turned off and working fine before, and tried turning it on but no luck. I can access my shared folders fine from other Computers and a ps3. I've read a couple threads of similar situations on various folders and none of their solutions have worked.

  Read the article

• Fedora12 Slow USB 2.0 Write Speed, ehci_hcd module is missing

  - by MA1

  I am using Fedora 12, the problem I am facing is USB 2.0 write speed. I have a dual boot system with Windows XP and Fedora 12. USB 2.0 write speed in Windows XP is much faster then what I am getting in Fedora 12. After searching Google I came to know that ehci_hcd module is missing/not present in my system. ehci_hcd module is neither loaded nor it is present in the available list of modules. Can someone guide me how to fix this issue? Does ehci_hcd have something to do with USB 2.0 write speed? Do I have to recompile the kernel and add/enable the ehci_hcd module?

  Read the article

• Rate limiting bandwidth per IP

  - by Yohan

  First, I am not that good with computer. I even had problem with Windows PC. Right now I own a restaurant which happened to offer free internet. My ISP has my connection setup using a Ubuntu 11.1 box. IP Address is 192.168.1.16 with netmask 255.255.0.0, dns is 192.168.1.1 and gateway is 192.168.1.1. My problem is that my customers complains all day about slow network. When I received that kind of complain, the first thing came to my mind is to scout my area and find out who is the culprit, and ask him not to waste our bandwidth. Now, it is getting bored scouting people around, and I need to implement to my Linux box to limit bandwidth. I don't care if their provider can't be faster, but I want to limit 70kbit for each person. More annoying are people who use flashget and torrents. Usually they consume the biggest bandwidth. My question, how can I limit that? Please guide me in easy way. I've spent few days reading tc documents but doesn't understand a thing. I am using Ubuntu 11.10 Basically, I want all my customer get 70kbps each, no matter what.

  Read the article

• Custom host file for Firefox

  - by acidzombie24

  Instead of changing my host file I'd like Firefox to think my domain is on my own server while my other browser uses the real IP address. I used to edit my host files but that forces both browsers to change the IP address. I found change host, but it doesn't appear to use the alternative host file. I also saw a comment asking when it will work on Firefox 6+. I tried Host Admin and it fails. It works but the alternative IP address must be in your host file already (which I don't want) and it lets you deselect a domain so the host file is ignored which is not what I want.

  Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >