Daily Archives

Articles indexed Thursday June 21 2012

Page 9/18 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• Message to distribution list with removed recipient bouncing back when sent from external mail server

  - by jshin47

  I removed a particular user from all distribution groups manually about five days ago. This user was a member of two particular groups that have other recipients. The OAB polling interval is 30 minutes, not that it really matters here. The situation is that I have an SMTP server that is not part of my Exchange organization that sends out automated email reports to these distribution groups. It sends them using a from: address that is a member of our Exchange organization. That member receives a bounce-back email indicating the member that should have been removed from the group does not exist. I have also verified that this is the same behavior when sending an email from a webmail service like GMail or Hotmail (outside of our Exchange organization of course) to either of those distribution group addresses. However when I send an email internally to one of those distribution group addresses everything works as expected (no bounce messages.) Not sure why this would be happening, but also not sure how to go about diagnosing the issue. I've looked at the SMTP headers and there are no relevant clues there as far as I can tell. I think it's an Exchange issue.

  Read the article

• Postfix "mail-to-script" pipe only delivers empty messages

  - by user68202

  i have a problem here. I want that a incoming email is piped to a php script in the system through postfix. My System is running with ispconfig 3, postfix and dovecot (< virtual mailbox users are saved in mysql). I looked already into this one: How to configure postfix to pipe all incoming email to a script? ... the script is executed, but no "message" is delivered to the script. My setup so far: In ISPConfig 3 i have set up the following email route: Active Server Domain Transport Sort by Yes example.com pipe.example.com piper: 5 excerpt from my postfix master.cf: piper unix - n n - - pipe user=piper:piper directory=/home/piper argv=php -q /home/piper/mail.php so far it is working great (mail sent to [email protected]) (mail.log): Jun 21 16:07:11 example postfix/pipe[10948]: 235CF7613E2: to=<[email protected]>, relay=piper, delay=0.04, delays=0.01/0.01/0/0.02, dsn=2.0.0, status=sent (delivered via piper service) ... and no errors in mail.err the mail.php is sucessfully executed (its chmod 777 and chown'ed to piper), but creates a empty .txt file (normally it should contain the email message): -rw------- 1 piper piper 0 Jun 21 16:07 mailtext_1340287631.txt the mail.php script ive used, is the one from http://www.email2php.com/HowItWorks if i use their (commercial) service to pipe an email to the mail.php (in a apache2 environment) through a provided "pipe-email", the message is saved sucessfully and complete. But as you can see, i dont want to use external services. -rw-r--r-- 1 web2 client0 1959 Jun 21 16:19 mailtext_1340288377.txt So, whats wrong here? I think it has something to do with the "delivering configuration" in my system...

  Read the article

• Locked out of our Comcast Business Gateway for seemingly no reason

  - by Tyler

  A little backstory... Last fall we migrated our ISP from AT&T to Comcast at one of our offices. At that time, we received a new modem/router from Comcast and we configured everything to our liking. We've never really had very many issues with the router aside from having to restart it every once in a while. Here's the problem... About three months ago I changed the password on the router from the default. After that, I logged into the router several times to make changes with no issue. During May I logged into the router to add two new static routes, no problems. A week ago, I tried to log into the router and could not. I tried the non-default password that I changed it to, the default, anything and everything I could think of and no luck. I restarted the router on Monday thinking it may just be locked up, but after the restart it would still not let me log in. This router is at our other office about 2 hours from here and I want to avoid having to drive down there and reset to factory defaults, reconfigure, etc. Any ideas?

  Read the article

• Is it possible to route *.example.com to a single machine without registering extra domains?

  - by oligofren

  I would like to achieve something similar to what wordpress.com does - giving each user its own subdomain. user1.wordpress.com would in the VirtualHosts setup of Apache would have its DocRoot at /user/user1, for instance. Now, our hosting service provider takes a fee for creating a domain, and in our case this would mean a ridiculous number of domains with a matching price. After some googling on DNS I came over a description of a DNAME record. That seems to fit the bill precisely. Any reason why my service provider would not do this, or why I should not do this?

  Read the article

• Restoring raid 5 array after bios flash

  - by cogergo

  I have just flashed my BIOS and now my machine does not detect my raid5 array! It has three 2TB drives in it so that is a LOT of data that will be lost! I have NOT deleted the array and it does not offer me to reboot I'm using Nvidia MediaShield! and Windows 7. Any ideas guys? Thanks! Update: here is the GUI raid configuration. As you see it shows one disk in the array but for some reason not the other two! Click for image of raid configuration error

  Read the article

• Rebuilding a file if files have changed

  - by Todd Strauch

  I'm having a hard time wrapping my head around this. It seems trivial, but I'm not getting it. I have two files. If either of those two files changes, I want to rebuild one of them. Essentially: if file a changes or file b changes then file {"a": content => template('a.erb', 'b.erb'), } I know I can audit a file for change, I just don't know how to include that within a conditional. Can anyone point me in the right direction?

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Apache can't get viewed from outside of my LAN

  - by Javier Martinez

  I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

  Read the article

• dom0 enable IPv6 for guests

  - by user98651

  I am looking at deploying IPv6 to my virtual machines. Right now I have v6 working great on the dom0 using a 6in4 provided by Hurricane Electric as I do not have native v6. However, I would like to distribute some of the /48 I am receiving to the domUs (/64 per machine would be ideal, but I am open to your suggestions). Static configuration on the domU side is fine. All I want to accomplish is getting the traffic to pass through the dom0 to the domU. To say the least, I'm still trying to wrap my head around all the virtual interfaces and bridges Xen creates. Yes, I have Googled around for this a bit and have not found anything great. I tried using two "vif-route6" bash scripts with no luck (possibly due to my ignorance with Xen networking). I am still stuck (mainly in how to configure the dom0). I would like to imagine this problem is relatively easy to solve and I look forward to your suggestions and help! Edited post to clarify my end goal: getting IPv6 to domU guests. I am completely open to suggestions but am hoping for something other than setting up a tunnel for every guest.

  Read the article

• Shared storage solution for our sql server backups

  - by Gokhan

  We have 3 clustered sql servers. We have 5+ multi terrabyte databases and their backup files (compressed using quest litespeed) are hitting over 600gb each, We are required to keep at least a week or two weeks (if we can) of weekly full backups and then 6 days differential backups, and a week or 2 weeks worth of log backups local. We are currently limited to 2TB volumes from our san team, we can have multiple volumes but they are expensive ($200 per raw TB per month) and having to deal with many backup volumes instead of a single big volume is difficult. I think if we could have a shared network storage of 20TB+ raid 10 or so for all our servers for keeping the backups and another department will copy them to tape from the network storage and delete files according to the retention period would be good, if this box would be a build in operating system (even unix a complete file storage system) that would be good. What do you guys think, does this make sense to you, is there any manufacturer that sells a storage product like that which that work in a clustered environment? Thank you

  Read the article

• OOF (Out of Office) is not working for remote users (Outlook Anywhere)

  - by Doughecka

  I'm not sure how long this issue has been happening, but recently a few of the remote sales users were going to a sales meeting and wanted to set their Out of Office... however in Outlook 2010, they get this error message: "Your automatic reply settings cannot be displayed because the server is currently unavailable" When I run the Exchange Remote Connectivity Analyzer, Autodiscover completes fine, but the next step fails: Exception details: Message: The request failed. The remote server returned an error: (403) Forbidden. Type: Microsoft.Exchange.WebServices.Data.ServiceRequestException Stack trace: at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request) at Microsoft.Exchange.WebServices.Data.MultiResponseServiceRequest`1.Execute() at Microsoft.Exchange.WebServices.Data.ExchangeService.BindToFolder[TFolder](FolderId folderId, PropertySet propertySet) at Microsoft.Exchange.Tools.ExRca.Tests.EnsureEmptyFolderTest.PerformTestReally() Exception details: Message: The remote server returned an error: (403) Forbidden. Type: System.Net.WebException Stack trace: at System.Net.HttpWebRequest.GetResponse() at Microsoft.Exchange.WebServices.Data.EwsHttpWebRequest.Microsoft.Exchange.WebServices.Data.IEwsHttpWebRequest.GetResponse() at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request) I've done some research, but I have yet to find a working fix for this... it seems like some permissions are messed up in IIS, but I haven't figured out what.

  Read the article

• Conditionnal relay in postfix

  - by Florent

  I use postfix to send direct email. But, I use a relay to send email for specific senders. So I use "sender_dependent_relayhost_maps" : /etc/postfix/main.cf : relayhost = transport_maps = hash:/etc/postfix/transport smtp_sender_dependent_authentication = yes sender_dependent_relayhost_maps = hash:/etc/postfix/sender_relay /etc/postfix/sender_relay : [email protected] smtp.relay.com So when I send an email with sender email "[email protected]", postfix will use the relay. But... I don't want to use the relay host for some recipient. ;) I think I must use "transport_map" to catch the email before it pass through "sender_dependent_relayhost_maps" but I don't know how to do it... Thanks

  Read the article

• Internal Code Signing: Key Distribution, or Certificate Server?

  - by Myrddin Emrys

  I should first note that we have nobody in IT with significant familiarity with self-signed certification. We have a moderately sprawling network (one forest, many locations), and we are now rolling out internal code signing; until now users have run untrusted code, or we even disabled(!) the warnings. Intranet applications, scripts, and sites will now be signed with self certification. I am aware of two obvious ways we can deploy this: Distributing the keys directly via a group policy, and setting up a cert server. Can someone explain the trade-offs between these two methods? How many certs before the group policy method is unwieldy? Are they large enough that remote users will have issues? Does the group policy method distribute duplicates on every login? Is there a better method I am not aware of? I can find a lot of documentation on certifications and various ways to create them, but I have not been able to find something that summarizes the difference between the distribution methods and what criteria make one or the other superior.

  Read the article

• Scanning to network share

  - by tking

  In our environment we have several printers with the scan to folder functionality set up. It worked pretty well. Long story short- I needed to reboot our file server one evening (the server whose $hares where all the scans go), upon on boot up I received a message stating the name of the file server (i.e AcmeFS1; Windows Server 2003) could not be used because there was a duplicate name on the network. I found that somehow another printer on the network was using the name of the file server. Weird - I know. People could no longer scan to their folders. I ran an nbtstat on the file server and found that the local netbios name table was empty. I renamed the offending printer and rebooted the file server once more. This time, no error, and once I ran nbtstat again, I found that correct name and domain in the local netbios name table. Problem is, scan to folder is still not working. I know this was working before I rebooted the file server the first time. Anyone have any idea what is going on and how to fix? Thanks. FIXED: Not sure why the reboot didnt fix it but I restarted the "Server" service on the file server and the problem went away.

  Read the article

• VirtualBox 4.1.12 Ubuntu Host Bridged Networking

  - by hidden_premise

  Setup Ubuntu Server 11.10 x64 VirtualBox 4.1.12 One network adapter eth0 with a static IP address My /etc/network/interfaces looks like #Local loopback auto lo iface lo inet loopback #Primary Interface auto eth0 iface eth0 inet static address 10.0.0.6 netmask 255.255.255.0 gateway 10.0.0.1 Need Static IP for Ubuntu Host Static IP for multiple Ubuntu guests My attempt Downloaded the .deb for 64bit virtual box dpkg -i virtualbox.deb Create a VM and install ubuntu server 11.10 x64 from ISO Set the networking mode to bridged and choose 'eth0' as the interface Fail. None of the guides I can find for bridged networking work because everything changed since vbox 2

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• Jenkins CI - Cannot allocate memory

  - by Programmieraffe

  I tested jenkins-ci successfully on a ubuntu 10.4 (with vmware fusion) on my local computer. Now I want to install and use it on my virtual server at hosteurope. The basic installation was no problem, but now I have problems with my build project. After pulling an mercurial update from a repository, ant is invoked and throws the following error in my build project: "Buildfile: /var/lib/jenkins/workspace/concrete5-seed-clean/build.xml [property] java.io.IOException: Cannot run program "/usr/bin/env": java.io.IOException: error=12, Cannot allocate memory" There is a known problem with heap size at virtual servers at hosteurope (http://faq.hosteurope.de/index.php?cpid=13918), so I tried to set the heap size manually: # for ant export ANT_OPTS="-Xms512m -Xmx512m" # jenkins # edited /etc/default/jenkins, added line JAVA_ARGS="-Xms512m -Xmx512m" # restarted jenkins via /etc/init.d/jenkins restart After setting this for ant, the command "ant -diagnostics" runs through and does not cause an error, but the error still occurs when I try to build the project. Server-Details: - http://www.hosteurope.de/produkt/Virtual-Server-Linux-L Ubuntu 10.4 LTS RAM: 1GB / Dynamic 2GB My questions: - Is 1GB enough for Jenkins or do I have to upgrade the server? - Is this error caused by ant or jenkins? Update: I got it running with ant options -Xmx128m -Xms128m, but sometimes the error occurs again. (this freaks me out, cause i can not reproduce it by now :/ ) Help much appreciated! Cheers, Matthias

  Read the article

• error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)

  - by ArunS

  We have online shopping site. When I am going to checkout page i am getting a error like this "error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)" From the apache error log i can see some attempts to connect to api.paypal.com. Here is the part of my apache error log * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.123... * connected * Connected to api.paypal.com (66.211.168.123) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 When i tried to connect to api.paypal.com using curl i am getting a error like this curl -iv https://api.paypal.com/ * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.91... connected * Connected to api.paypal.com (66.211.168.91) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Request CERT (13): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS alert, Server hello (2): * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 curl: (35) error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure Can anyone help me to figure out this. Thanks in Advance. Arun S

  Read the article

• How can I cause Task Scheduler to "fail" if a dialog box returns a certain result?

  - by Roger

  I'm working on a VBScript to do a weekly reboot of all machines on our network. I want to run this script via Task Scheduler. The script runs at 3:00 AM, but there is a small chance that users may still be on the network at that time, and I need to give them the option to terminate the reboot. If they do so, I would like the reboot to occur the next night at 3:00 AM. I've set Task Scheduler up to repeat in this way. So far, so good. The problem is that if the user selects "Cancel" in my script, the Task Scheduler does not see my task as failed, and won't run it again the next night. Any ideas? Can I pass an errorcode to task scheduler or otherwise abort the task via VBScript? My code is below: Option Explicit Dim objShell, intShutdown Dim strShutdown, strAbort ' -r = restart, -t 600 = 10 minutes, -f = force programs to close strShutdown = "shutdown.exe -r -t 600 -f" set objShell = CreateObject("WScript.Shell") objShell.Run strShutdown, 0, false 'go to sleep so message box appears on top WScript.Sleep 100 ' Input Box to abort shutdown intShutdown = (MsgBox("Computer will restart in 10 minutes. Do you want to cancel computer restart?",vbYesNo+vbExclamation+vbApplicationModal,"Cancel Restart")) If intShutdown = vbYes Then ' Abort Shutdown strAbort = "shutdown.exe -a" set objShell = CreateObject("WScript.Shell") objShell.Run strAbort, 0, false End if Wscript.Quit Appreciate any thoughts.

  Read the article

• Hooking domain to home server (WinServer2008) with specific port

  - by user1071461

  Alright, I'm asking two things here. First of all, if i purchase a domain let's say myhomeserver.com, am I able to make the default port go through a different port instead of the default port 80? (that is without having to do myhomeserver.com:5000 for example). Also this should be without blocking other ports (so no stealth forwarding to myhomeserver.com:5000 i think) Secondly, How could I go about hooking a domain to a windows 2008 server? I've seen it on linux but no clue how to do it on windows if it's even possible. I know I'm asking a lot here, just some tips are appereciated. Also, yes I know, using a home server is horrible for security and preformance and whatnot, I understand this already, thanks ^^

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• why is my Bamboo pen always drawing and a yellow note pad appears?

  - by cboi

  I have had a Bamboo pen and touch tablet for a couple years but have not used it in a long time. Now that I'm trying to use it again it is behaving very strangely. It won't drag anything on my desktop, the minute I try there is this yellow pad that appears and the pen draws a line on it instead of dragging the file. The yellow pad and drawn line disappear the second I lift the pen from the tablet. The most frustrating is it does the same thing when I try to draw in Photoshop. It won't draw with the paintbrush on my canvas because the minute I try to this yellow pad appears and it draws a line on it instead of on the canvas, which disappears the second I lift the pen from the tablet. It also bizarrely automatically switches from the paintbrush to the automatic selection tool. Has anyone had this problem? Any suggestions on how to fix this? I operate with Mac OS X 10.5.8

  Read the article

• Copy files with original folder structure, but to 8.3 format

  - by kokbira

  I have a folder with a lot of files and folders inside it. I would like to copy that to another location so the result is a folder with the same file and folder structure, but with all files in 8.3 format. How to do it? PS: Well, some files have extensions with more than 3 characters (e.x. home.sh3d, windows.theme etc.), so when I say about transforming all filenames to 8.3 I would like to say about transforming them to a 8.X format (i.e., to do not change extensions).

  Read the article

• Using external monitor and screen resolution?

  - by Johnydep

  it might sound very basic question but i need some help. I have lenovo Ideapad y560p which offers a maximum resolution of 1366px x 768px. Now i am planning to buy an external monitor, and i short listed some FULL HD resolution monitors, but it is my understanding that even with FULL HD, i would only achieve the best resolution my laptop supports. Is it true? And also if this is the case, should i really go for an HD monitor or settle down with a lower resolution version? 2ndly, is there any way to increase resolution with simple upgrade? or it is not possible without voiding the warranty??

  Read the article

• CPU not working on a specific motherboard

  - by Shaman

  I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >