Daily Archives

Articles indexed Monday September 24 2012

Page 9/18 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

  • asterisk queues priority and penalty

    - by MealstroM
    queues.conf shared_lascall=yes strategy=rrmemory wrapuptime=15 A1,A2,A3 are members of 2 queues: queue1(Q1) and queue2(Q2) A3 has penalty 3 in Q1 where min/max penalty are 0/3 and A3 has penalty 0 at Q2 where min/max penalty are 0/3. A3 has just ended a call and is on wrapuptime pause. User1 (U1) enters Q1 with priority 10, and user2 (U2) enters Q2 with priority 15. A3 wrapuptime ends. What user U1 or U2 will be served first?

    Read the article

  • Just how slow should my VPN be?

    - by David Heggie
    I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

    Read the article

  • How to forward OpenVPN Port to NAT'd XEN domU

    - by John
    I want to install a OpenVPN domU on XEN. Dom0 and domU are running Debian Squeeze, all domU are on a NAT'd privat network 10.0.0.1/24 My VPN-Gate is von 10.0.0.1 and running. How can I make it accessible under the dom0 public IP? I tried forwarding the port using iptables, but without any success. Here is what i did: ~ # iptables -L -n -v Chain INPUT (policy ACCEPT 1397 packets, 118K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 930 packets, 133K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT all -- * * 10.0.0.1 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT all -- * * 10.0.0.5 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT all -- * * 10.0.0.2 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 147 8236 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 13 546 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain OUTPUT (policy ACCEPT 1000 packets, 99240 bytes) pkts bytes target prot opt in out source destination ~ # iptables -L -t nat -n -v Chain PREROUTING (policy ACCEPT 324 packets, 23925 bytes) pkts bytes target prot opt in out source destination 139 7824 DNAT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 to:10.0.0.5:80 1 42 DNAT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 to:10.0.0.1:1194 Chain POSTROUTING (policy ACCEPT 92 packets, 5030 bytes) pkts bytes target prot opt in out source destination 863 64983 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 180 packets, 13953 bytes) pkts bytes target prot opt in out source destination

    Read the article

  • How can i lock images to a cell in excel 2010

    - by Jamie
    Ok, so i am using microsoft excel 2010 and have a set up currently where i have 2 views expanded and deflated using the Group or +/- function. My problem is that ui have images on the workbook too. The images are over the cells which are to be "hidden" when the - button is pressed and i would like the images to disappear with them. This is not curently happening instead they are moving to the next visible cell. I have included an example below incase i wasn't clear. I wish to hide Columns M:AU and the images are in various cells suchas N5 and O5. When i colapse (hide) the column range all of the images move to "AV5" the next row along that isn't hidden. This means the workbooks is looking messy when colapsed which is the oposite of what i was trying to do. Can anyone advise on a way around this?

    Read the article

  • How to "demote" all titles and headings in Word 2010?

    - by dangowans
    I built a large help document for an application I wrote. I used all the default styles in Word 2010, including "Title", "Heading 1", "Heading 2", etc. Sadly, when I generated the Table of Contents, Titles were not included. I'm also now using chmProcessor to automatically generate a website from the document, and it's not including Titles in its Table of Contents either. I'd like to make all Titles into Heading 1s, all Heading 1s into Heading 2s, and Heading 2s into Heading 3s, etc. Is this possible without a huge manual effort? (I'm sure there's a better word than "demote" for this.)

    Read the article

  • Autologin 2 Windows users OR Login another user from the desktop

    - by fpdragon
    I'm using two windows users on my HTPC at the same time. One is just for watching videos and one for administration via remote. This setup is quite ideal for me since windows can handle multiple concurrent logins and the win "rdp concurrent hack" (Google). The problem is, I want both users to be logged in automatically when the pc was started. It shall be possible to watch tv and also the admin user shall be automatically logged in to start my scripts and other tasks, even if I haven't logged in via remote desktop manually. Later, when I want to admin my htpc I can just rdp connect the admin user without interrupting the video playback on the actual HTPC's screen and check my cleanup tasks, downloads, ... witch already executed for this admin user. But right now I found no solution to automatically login user A from a user B desktop and I also found no solution to autologin both users immediately at startup. As a workaround I have to fire up my other notebook machine and login one time with the remote user via rdp. From this time on the remote admin user is running concurrent with the main user in the background of the machine. The other workaround would be... after startup switch user from main user to admin user and then back again. But that also requires manual steps. I'm on a Windows 8 System right now but all infos for Win7 or XP would be also interesting. thanks a lot for all ideas. PS: just to prevent useless posts... don't tell me that only one user can be logged in to windows. ;)

    Read the article

  • VBScript Capture StdOut from ShellExecute

    - by Joe
    I am trying to run the following code snippet as part of a tool to gather and log some pertinent system diagnostics. The purpose of this snippet is to gather the result of running the command: vssadmin list writers The snippet is as follows: ' Set WshShell = CreateObject("WScript.Shell") ' WScript.Echo sCurPath & "\vsswritercheck.bat" ' Set WshShellExec = WshShell.Exec("elevate.cmd cmd.exe /c " & sCurPath & "\vsswritercheck.bat") Set oShell = CreateObject("Shell.Application") oShell.ShellExecute "cmd.exe", sCurPath & "\vsswritercheck.bat", , "runas", 1 vsswriter = VSSWriterCheck Select Case oShell.Status Case WshFinished strOutput = oShell.StdOut.ReadAll Case WshFailed strOutput = oShell.StdErr.ReadAll End Select WScript.Echo strOutPut vsswriter = strOutPut With the first code snippet (commented out) I can run the command and capture stdout from the batch file. In the second code snipped, I cannot capture stdout. I need to be able to run the batch script with Elevated permissions, so I am looking for a compromise between the functionality of the two. I cannot run the entire calling script in elevated mode due to restrictions from other pieces of functionality. I am looking for any ideas on how to add this output to my log as I am running out of options that are within the scope of basic scripts.

    Read the article

  • The sound freezes while listening to music

    - by Scott
    I have bought an sound card - Sound Blaster X-FI Surround 5.1 PRO and while I'm listening to the music, after few minutes or even hours (it does happends randomly) the sound dissapears and I have to go settings: Playing Devices - Advanced and switch the Default Format (sampling frequency) and switch from the `16-bits, 48000 Hz (DVD Quality) to any other from the list (16-bits, 96000 Hz or 24-bits, 48000 Hz or 24-bits 96000 Hz). I have been trying to set all of the above options, but for all of them the sound freezes after listening to music. It is getting annoying and I hope its the settings fault and not my sound card. I got my drivers installed from the attached CD and I'm running Windows 7 HP 64 bits. If anyone would try to help me, I would really appreciate this.

    Read the article

  • DSA private key format

    - by ansur
    So I used puttygen to generate a DSA private key and then exported that to the OpenSSH format and here's what I got when I ran OpenSSL's asn1parse on it: 0:d=0 hl=4 l= 443 cons: SEQUENCE 4:d=1 hl=2 l= 1 prim: INTEGER :00 7:d=1 hl=3 l= 129 prim: INTEGER :B9916796B7A3EFFD5CA36368186D0ED 193BE7FDD61CC6851174F3E9781A0C0CEA7473E528372F559A1DB2A7E049A9BEFAE2CAAC55527049 2A0CD55B59A48A53BCADD32181F519EA9E6A98EF8EF59DE314A2E69606C728F2F8DEE722B4C67BA6 8EB8A619B6006804F83740F9C74C38136522E7E83F22920AA39822FBDA0DF4D0B 139:d=1 hl=2 l= 21 prim: INTEGER :D832F5B01F075FEC0F162B91982F34D B26A0CC29 162:d=1 hl=3 l= 129 prim: INTEGER :9B73F47AEFF8E39584FD10ACF81CCD5 75C96FC5558A5C94B941EF76318D132007ACAE1EA22E95CE0B13FC7875CE4D4ED33BA639CD8C2AC9 C0A0530FB7786F584A62EBAE5985E1C26ED0D0B9FDD5E8DB0142BE182A4E5359307007060C327FEE C2F8D04EABB37D7B74076EB9BDB4885F627DE85708D5BDBF5177A05721E09A367 294:d=1 hl=3 l= 128 prim: INTEGER :6BD9267D2D1E4546EE05F6CD087F311 93C0EEB13B1E139F5072E900AB2EEF68EEC28BF4D7D6CAE4DEE59005F00BAE07343EE520C217FF6E 7880DC788E4555F78CCB5E89A10CDC71A663DA696C5BC34E296CEB3518D65A79BF00B6D592B1399A 9F0D79AE3F3FB445EE1F2B4B72515F036C8E1D5C7FAD336FD3503874645C5C264 425:d=1 hl=2 l= 20 prim: INTEGER :15295A12325E5F1A6F7243B7BB3BE74 6FE7B76E9 My question is... where is this format described? What does the first 0 integer value mean for example? I guess I could look in the puttygen source code but is there an RFC describing this format or something?

    Read the article

  • Google Chrome is in Danish

    - by Mad Cow
    I'm not sure what i have done, but by default, Chrome comes up in Danish. I can ignore this most of the time but its v annoying and i cant seem to change it. For example google directions come up in Danish too and have to be translated back to English! I have tried the spanner icon, and i've confirmed the only two languages specified are En and US English. Does anyone have any ideas how i can default it back to English all the time. In-lined the original screenshot from www.cow-shed.co.uk Thanks

    Read the article

  • Windows 8 start screen will only find apps matching full words

    - by Ian Oakes
    Since doing a fresh install of Windows 8 x64 RTM I'm having trouble starting apps from the start screen. In previous version I could just start typing the apps name and I would be presented with a list of matches that decreased in number as I continued typing. In the RTM version I have to type complete words to find a match. i.e. if I want to run powershell I have to type in powershell before I get any hits. Like wise if I want to start Visual Studio I have to type visual before I get a match. If I continue and start typing Studio the match goes away and doesn't return until I finish typing studio. This problem does not affect Setting or Files which show all possible matches. Any ideas what is wrong?

    Read the article

  • Is it possible to live-boot VirtualBox from a USB flash drive?

    - by bw.
    To clarify, I'm not asking if you can boot from USB from within VirtualBox. I would like to make a portable version of Windows 7 that I can run from a USB drive on any machine. I'm putting a distro of Linux on my laptop, but I manage a Windows domain at work so I'd like an easier management solution than trying to use Linux tools to interface with a Windows DC(as RDP to a DC is not always an option). The reason I'm inquiring about VirtualBox... I plan on carrying this portable installation with me and using it on multiple machines, so I would like to avoid driver conflicts (which I imagine would happen if I only installed Windows on a flash drive). Basically, I need a way to boot an installation of Windows 7 from USB that still allows me to install/remove/update programs as if it were installed on a standard hard drive, and not freak out over different hardware configurations. Please help, superusers!

    Read the article

  • I've set an editor as default, how do I call it to open files in a shell?

    - by iight
    EDIT I thought of a better way to phrase the question. How can I find the alias that Ubuntu is using for a different text editor? Rather than using nano by typing nano file.txt, i'd like to be able to type sublime file.txt to open sublime editor. I don't know where to look to find these aliases. sudo update-alternatives --config editor does not show it as a choice, I only see the 'default' editors, like Nano and vim.tiny.

    Read the article

  • How can I tell my dd-wrt router to use someone's Amazon Affiliates link when I point my browser to amazon.com?

    - by Michael Paul
    Here's what I'd like to do. Instead of a one-time donation to one of my favorite free tools (junecloud.com) I'd like to do what they suggest here and use their Amazon Affiliates link to do all my Amazon shopping. I shop at amazon once or twice a week, so this is a great way to let them earn lots of long-term cash without me dropping a dime. My thought was to go into my dd-wrt enabled router and tell it, "any time I go to amazon.com on any computer in the house, please go to http://www.amazon.com/gp/redirect.html?link_code=ur2&tag=junecloud-20&camp=1789&creative=9325&location=%2F instead. (That URL simply redirects me to amazon.com but every purchase I make during that session is credited to JuneCloud.) Once logged into dd-wrt, I went to Services Services DNSMasq but I'm not really sure how to get it to work from there, or if it's even possible. I know I can redirect IP addresses, but I'm looking to redirect someone on my network from amazon.com to the special amazon affiliate code link. Hope that's clear. Thanks for any replies!

    Read the article

  • Need old version Firefox Java plugin

    - by Bryan
    I need to use Java 1.6.0_20 for the software I'm running. I went to the Oracle website and downloaded jre1.6.0_20 and installed it on my computer, but can't seem to get Firefox to load Java. If I download directly from http://www.java.com/en/download/manual.jsp, the plugin works fine but is the wrong version, and I can't find on www.java.com anywhere to download any of the previous versions. According to the help (can't post link because of spam prevention), I need to go into the Java Control Panel and enable it for Mozilla. I've done this multiple times, but every time I go in to the control panel and check the box, click Apply and Save, as soon as I go back in the box is unchecked. Does anyone know either why the box is unchecked, or where I can download the old JRE that also is configured for Firefox?

    Read the article

  • vmware windows7 professional changing ip addresses

    - by chris hough
    is there a way to fix your windows 7 professional guest host os ipaddress so it does not change every time you startup? I am currently using NAT for networking and would like to remain using this networking method if possible. In older versions of windows this never used to be a problem in vmware so I am wondering if I am missing a setting in windows 7 professional or in vmware. thank you for your help, chris

    Read the article

  • How to make mouse in Windows 7 act the same as Windows XP

    - by Phenom
    In Windows XP using TweakUI I could enable an option so that when my mouse goes over an inactive window, it makes that window the active window. There is also another separate option so that if the window becomes active, it automatically becomes the topmost window. I like to enable the former but not the latter. For Windows 7 I have not been able to find the same thing. What I found instead is an option inside windows that does something similar. If I move my mouse over an inactive window, I have to hover over it for a while before it becomes active. It is not instantaneous. The second problem is that once it does become active, it automatically makes itself the topmost window, covering other things I don't want covered. In summary, this is what I want in Windows 7: When my mouse goes over an inactive window, it immediately makes it the active window. When it activates the window, it does not raise it above other windows.

    Read the article

  • Create a primary partition on Windows 7

    - by TutorialPoint
    I have windows 7 installed. On the moment i have the following partitions on 1 hard disk: (300 GB) C: (Windows) (Primary, System, Boot, Page File, Crash Dump, Active) 100 GB D: (Data) (Logical) 100 GB E: (System Reserved created after Boot repair) (primary, system) 100 MB Now i want to create a new primary partition on this disk, because i have +/- 100 GB left, for a new OS. However when trying to make a new partition, it makes it a Logical partition, not Primary. How to make it primary...?

    Read the article

  • Windows program to remove titlebar, frame, etc from a window?

    - by Nelson
    I like playing computer games in windowed mode, as opposed to full screen. I don't like staring at the title bar, frame, and other UI junk. I also don't like seeing other stuff on my desktop around the window. Is there a simple Windows program that will strip the UI chrome off of an arbitrary window from some other application? Extra points for an easy way to put a black screen underneath the window, hiding the desktop. Note: I'm looking specifically to handle windows that are smaller than my desktop size. There's a variety of 'windowed maximized' options that make a window exactly the desktop size, and positioned so all the UI decorations are off screen. (E.g.: ShiftWindow). I'm trying to strip all the decorations away from a window that's smaller than desktop size.

    Read the article

  • Netflix Rolls Out Polished New iPhone and Android Apps [Video]

    - by Jason Fitzpatrick
    If you’re a Netflix subscriber, you’ve got a brand spanking new mobile interface to take for a spin. Last week Netflix released a brand new iOS interface, this week it’s a brand new Android interface. The above video showcases the new iOS interface for mobile playback on devices like the iPhone and iPad. The slick new layout makes it even easier to browser new content and resume watching content you’ve paused at home or on the go. For a peek at the new (and similar) Android interface, check out the video below: For more information about the respective apps, visit their download pages to read up and grab a copy. Netflix for Android / iOS How To Create a Customized Windows 7 Installation Disc With Integrated Updates How to Get Pro Features in Windows Home Versions with Third Party Tools HTG Explains: Is ReadyBoost Worth Using?

    Read the article

  • Launch Photography Is a Beautiful Collection of Shuttle Photos

    - by Jason Fitzpatrick
    Photographer Ben Cooper has a soft spot for the Space Shuttles; check out this excellent galleries to see everything from dynamic launch photos to beautiful fish-eye photos of the cockpits. Launch Photography [via Neatorama] How To Create a Customized Windows 7 Installation Disc With Integrated Updates How to Get Pro Features in Windows Home Versions with Third Party Tools HTG Explains: Is ReadyBoost Worth Using?

    Read the article

  • Découvrez les éditions de Visual Studio 2012 et leurs nouvelles fonctionnalités de design et de gestion du cycle de vie des applications

    Découvrez les éditions de Visual Studio 2012 ainsi que les fonctionnalités adaptées à vos besoins de la solution de gestion des projets logiciels Mise à jour du 24/09/2012 Visual Studio 2012 est disponible depuis le 12 septembre 2012. La solution propose une nouvelle génération d'outils de développement, de collaboration et de gestion du cycle de vie pour la conception des applications non seulement modernes et attrayantes, mais aussi accessibles n'importe où, n'importe quand, répondant aux attentes des clients. [IMG]http://rdonfack.developpez.com/images/vs20...

    Read the article

  • iOS 6 "jailbreaké" moins d'une journée après son lancement par le groupe de hackers Dev-Team, l'iPhone 5 bientôt déverrouillé ?

    iOS 6 "jailbreaké" moins d'une journée après son lancement Par le groupe de hackers Dev-Team, l'iPhone 5 bientôt déverrouillé ? L'iPhone Dev-Team, un groupe de hackers indépendant spécialisé dans les produits Apple, a réussi à créer un Jailbreak (déverrouillage) pour l'iOS 6. Cette annonce est survenue moins d'une journée après la sortie de ce dernier. [IMG]http://idelways.developpez.com/news/images/jailbreak.jpg[/IMG] Sorti dans la lignée du célèbre outil redsn0w, le jailbreak fonctionne seulement pour l'iPhone 4, l'iPhone 3GS et la quatrième génération de l'iPod Touch, soit uniquement des dispositifs équipés de processeurs A4. L'iPhone 5 n'est ...

    Read the article

  • Coup d'envoi d'Imagine Cup 2013 : Microsoft double le montant des primes du championnat de l'innovation numérique pour étudiant

    Coup d'envoi d'Imagine Cup 2013 : Microsoft double les primes et modifie la thématique de son championnat de l'innovation numérique pour étudiant C'est parti pour une nouvelle saison d'Imagine Cup, le championnat du monde étudiant de l'innovation numérique organisé par Microsoft. [IMG]http://rdonfack.developpez.com/images/imaginecup20132.jpg[/IMG] Créé en 2002, Imagine Cup permet à des étudiants du monde entier de « s'affronter » pour révéler leur potentiel créatif et entrepreneurial avec une mission : répondre à un ou plusieurs des « Objectifs du Millénaire pour le Développement ». L'édition 2013 de la compétition est ouverte dan...

    Read the article

  • PlanetHoster ouvre un datacenter en France et vient chasser sur les terres d'OVH, qui ferait « plus de quantité que de qualité »

    PlanetHoster ouvre un datacenter en France Et vient chasser sur les terres d'OVH qui ferait « plus de quantité que de qualité » L'hébergeur canadien PlanetHoster vient de faire un investissement de plusieurs centaines de milliers d'euros pour ouvrir un nouveau datacenter en France (à St-Denis). « C'est à la demande de beaucoup de clients européens qui souhaitaient avoir leur hébergement proche d'eux », explique Saber Bariz, le créateur de la société. On peut imaginer que les contraintes légales sur la localisation de certaines données sensibles aient poussé ces clients à formuler la demande. Mais c'est surtout le gain de performance qui aurait motivé le...

    Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >