Search Results

Search found 18132 results on 726 pages for 'connection timeout'.

Page 100/726 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

  • Wireless Network Disappearing From Available Networks (Windows 7)

    - by PeteDaMeat
    I have been using Windows 7 with a BT Voyager wireless adapter to connect to my home wireless network for around the last 6 months or so and until recently have experienced no problems. However, over the last couple of days Windows has been unable to connect to the network and the network name is no longer visible in the list of available wireless networks. The only way I have got round the problem is to reboot the NetGear router and to change the SSID to a network name which has not already been used. I do not believe the problem is with the router as my mobile phone can connect to it without any problems. The BT Voyager wireless adapter detects all other available networks so I presume this is a Windows 7 issue as it seems to occur when the PC is rebooted. This problen has happened twice in the last 2 days and is becoming extremely annoying. Does anyone have any suggestions?

    Read the article

  • Outlook refuses to connect to Exchange

    - by wfaulk
    Outlook 2007 under Windows XP connecting to Exchange 2003 SP2: when started, it flips back and forth between "Connecting to Exchange Server" and "Disconnected" three or four times, then gives up and stays disconnected. I tried deleting the ost file (which was nearly 2GB), turning Cached mode on and off, recreating the account inside the Mail control panel, changing the account to use HTTP, and probably some other things. None of it seemed to make any difference, until … After fiddling with it for a while, I got this absurd error message dialog at startup, and it exits after I click OK: Cannot start Microsoft Office Outlook. Cannot open the Outlook window. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. (I'm not sure if I can even trust that message. It's so long, it just feels like a random offset into Outlook's stack of error messages.) Either way, the Exchange server is available to everyone else, and is available via OWA from that computer. I ran Process Explorer against Outlook and it showed 5 or so ESTABLISHED connections to our Exchange server, plus listening on two UDP ports, and two CLOSE_WAIT connections to localhost. If I managed to look at Outlook's IP connections while it was doing its Connecting/Disconnected dance, it had a huge number of connections open to the Exchange server. It more than filled ProcExp's dialog box; I'm guessing at least 20, probably more. The only other odd thing is that our network admin at some point added a wildcard DNS record to the domain name that we use for email, and now Outlook will sometimes (always?) start by complaining about autodiscover.example.com's SSL certificate. There is a web server there, but it doesn't have any sort of email autodiscover anything on it. It doesn't make any difference if I click "OK" or "Cancel" (or whatever the buttons are). I also added a bogus entry for the hostname to Windows' hosts file, pointing it at 127.0.0.2, and it stopped complaining about the certificate. (The CLOSE_WAIT sockets above were from before I made this change, and went away after.) I don't think this is related, as the same problem should exist for everyone, but it might be. This is the second time this user has had this problem. The first time, I never found a solution other than reinstalling Outlook. Now that it's a pattern, I'd like to find a permanent solution, rather than assume it's a random glitch.

    Read the article

  • Internet connectivity issues with one router but work ok with other router

    - by user825904
    I have one Tplink ADSL ROUTER and when i enter username and password on setup page then everything works fine. Now i have one more router Netgear router then when i enter same username and password then interworks ok for some 50% websites but for other 50% websites the page is not loaded and it hangs there. In the sats bar it says website found , waiting for reply and it hnags there and no site is displayed. I wonder which setting is different on these two routers. The Tplink router i have bought is from local shop but netgear router is from different country. Can that make some difference

    Read the article

  • Best way to connect a desktop computer to a 3g network

    - by dbyrne
    A friend of mine is moving to a building with no Internet connectivity. Ethernet and wifi are out of the question. What is the best way for him to get his desktop connected? The most obvious solution is for him to get an unlimited 3G data plan. What is the best way for him to set this up? I am assuming he should get something like Verizon's MiFi 3G access point, but does this have an ethernet jack?

    Read the article

  • USB-to-Parallel adapter rated as USB 1.1 - will its driver lower speed of USB 2.0 bus?

    - by cumminjm
    I need to connect a printer with a parallel port to a computer with only a USB 2.0 bus. I'd like to do so without lowering the USB 2.0 bus speed to USB 1.1. All the USB-to-Parallel adapter cable found so far seem to be rated as USB 1.1 and they come with a CD which presumably contains a necessary driver. I haven't purchased one and tested it out yet, but if so, would the cable's driver lower speed of USB 2.0 bus?

    Read the article

  • "Play on another device" function not working with Samsung Allshare

    - by Tural Teyyuboglu
    Briefly I can't get work "Play on another device" function More detailed My Samsung TV (which support network) and PC are in the same network. The problem is, I can play PC contents from TV. But when I try to control TV remotely from Allshare software (PC), it shows TV only as connected device: But not as remote player in "players" list The result Tried to turn off firewall completely, reset router, re-install software. No success. Please help. BTW. On this link they kinda explained how to do it, but I software doesn' detect the TV as player in my case: http://www.samsung.com/global/allshare/pcsw/quickguide.html

    Read the article

  • How to connect SharePoint Online with Dynamics CRM Online using BDC?

    - by ripperus
    I try to connect SharePoint Online with Dynamics CRM Online using BDC. But without any results. I'll try to using Account's from CRM in SharePoint Online like a list. I mean - when I have 100 account's (customers) in CRM I want to export this account's to SharePoint Online like a list. And when I will bed edited account in CRM the elements in the list will be update (and when I edited element on SharePoint list it will update in CRM). Is there any possibility to connect in this way? If if what I should use - SharePoint Designer 2010, Visual Studio or do this on web interface?

    Read the article

  • Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

    - by Abdul Majeed
    I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

    Read the article

  • Can't connect to YouTube from specific network

    - by Tyilo
    Using my current network, I am unable to connect to http://www.youtube.com/. It doesn't matter what browser I use or if I use a cli-command (wget, curl). Error in Google Chrome: Oops! Google Chrome could not connect to www.youtube.com Error using curl: curl: (7) couldn't connect to host If I use nslookup to get the IP-address of YouTube, I get 173.194.32.32. If I go to http://173.194.32.32/ in my browser it can connect, but as Google is probably checking the Host HTTP-header, it shows Google's frontpage instead. There is no blocked websites on the router and other devices on the network seems to work. My computer only has this problem on this specific network. I am using Mac OS X 10.8.2 on a MacBook (mid 2009).

    Read the article

  • Why can't I access a particular website even though the server appears to be available

    - by 50ndr33
    I can't access http://www.lynda.com/ with any of my browsers on my home network. By checking http://www.downforeveryoneorjustme.com/, I can see that the server is up and I can access it via a proxy like TOR. This screen appears immediately after I type the page in It doesn't even try to load the page, it seems. Though when I ping the server I get this: I tried to do ipconfig /flushdns. But it didn't help either. Anyone know how to fix this?

    Read the article

  • 4 - 7 second delay accessing Mysql across the network

    - by Kristiaan
    Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

    Read the article

  • connect to paltalk server using a proxy

    - by user40026
    Hi I want to use paltalk, which is a kind of chat software, but the ports that this applications uses are closed in my country. What I need to do is to use a proxy server. Unfortunately the software itself does not provide a proxy setting. I though it would be possible to run paltalk on an O.S. installed on a virtual machine (say virtualbox) and configure the network setting of virtual machine to direct all its traffic through a proxy on host Operating system, but I could not find a way to do so neither. can anyone please help me?

    Read the article

  • Why do my proxy settings keep changing?

    - by tjrobinson
    I am running Windows 7 and a few times a day the "Use a proxy server for your LAN (These settings will not apply to dial-up of VPN connections)." under "Local Area Network (LAN) Settings" checkbox becomes checked seemingly on it's own. Am I pressing some kind of hidden keyboard shortcut accidentally? What sort of applications might alter this setting and why? Unfortunately as this is a developer box, there's a lot of stuff that could be interfering, e.g. Visual Studio 2010, Windows Azure SDK and various browsers. Has anyone else come across this?

    Read the article

  • Experiences with Google TiSP?

    - by Zypher
    i got an email from google a couple of hours ago (around 12AM EST today) that Google's TiSP service is now available in my area. this seems like a great deal compared to my cUrrent 16Mbps cable coNction at work, however i'm a lIttle nervous about the fact that linux support is "Coming soon". i was wOndering if anyone had successfully installed this system and gotten it woRking with their linux infrastructure? I'm assuming that there shouldn't be any issues siNce we have an ASA in front of our internet. TiSP Shouldn't care what is behind that. Any insight would be greatly appreciated!

    Read the article

  • Connect server to router with workstation in between?

    - by letseatfood
    I have a server (9 yr old Dell with Ubuntu 10.04 Server Edition) and a workstation (Laptop with Vista) which are both connected to a router. The workstation is able to access the server via web browser for testing my web development projects. Since the server is old and does not have a wireless card, I am wondering if it is possible to connect the server directly to the workstation while maintaining the ability to connect to the server from the workstation. The reason is that the computers are in a separate room from the router and I am trying to limit the amount of wires on the floor, along with trying to avoid buying more hardware (like a wireless card). Thanks and I will be more than happy to clarify!

    Read the article

  • Could some one please explain the various proxy configuration scenarios?

    - by RP.
    I am working on a client application in C# which does a various kinds of communication with a server( eg: uploads, downloads etc ). We have a legacy system which does the same functionality and we get in to proxy configuration related issues frequently.It uses the settings from internet explorer network settings. Most of the time these are due to specific proxy configuration( Eg: Proxy auto-config etc ). I am trying to understand the various scenarios used in corporate environments for proxy configurations. Could some one please explain the various proxy configuration scenarios?

    Read the article

  • Problem connecting to MySQL with zend

    - by wheresrhys
    I've set up a virtual host on my local machine (windows xp with xampp installed), have installed zend there and am now trying to connect to the MySQLdatabase. I get the following error message: Message: SQLSTATE[HY000] [2003] Can't connect to MySQL server on ''myhost.com'' (10060) All the tips I've found via google haven't helped. I use kaspersky antivirus and have added port 3306 to the allowed list for MySQL and Apache. I've also pinged myhost.com:3306 and get a response (with ip address 67.63.50.51), though localhost:3306 and 127.0.0.1:3306 aren't found. I've checked that other apps can still access MySQL if the virtual host is pointed at them instead and my non zend apps do work. I guess I have to do something further to the port, or maybe force the app to use a different port, but am not sure how to do either. Any help appreciated.

    Read the article

  • More than 10k connections on linux vps

    - by Sash_007
    my question what is causing this and how to check? we use url masking script is the website..is it causing this?please help We could noticed that you are abusing our network, as you have made more than 10k connections in our node due to this our node became unstable and all of our customer faced down time because of your VPS. Please find the log details below for your reference. ============================== 593 src=199.231.227.56 dst=58.2.236.196 465 src=199.231.227.56 dst=192.223.243.6 396 src=199.231.227.56 dst=58.2.238.191 217 src=199.231.227.56 dst=58.2.236.197 161 src=199.231.227.56 dst=20.139.83.50 145 src=199.231.227.56 dst=192.223.163.6 136 src=199.231.227.56 dst=125.21.230.68 134 src=199.231.227.56 dst=125.21.230.132 131 src=199.231.227.56 dst=20.139.67.50 117 src=199.231.227.56 dst=110.234.29.210 112 src=199.231.227.56 dst=65.52.0.51 104 src=199.231.227.56 dst=202.46.23.55 100 src=199.231.227.56 dst=202.3.120.4 94 src=199.231.227.56 dst=117.198.39.22 69 src=203.197.253.62 dst=199.231.227.56 62 src=14.194.248.225 dst=199.231.227.56 53 src=199.231.227.56 dst=192.223.136.5 52 src=49.248.11.195 dst=199.231.227.56 51 src=199.231.227.56 dst=117.198.38.15 50 src=199.231.227.56 dst=192.71.175.2 47 src=199.231.227.56 dst=61.16.189.76 45 src=199.231.227.56 dst=122.177.222.17 43 src=199.231.227.56 dst=115.242.89.40 42 src=199.231.227.56 dst=103.22.237.215 41 src=125.16.9.2 dst=199.231.227.56 39 src=199.231.227.56 dst=117.198.35.90 38 src=199.231.227.56 dst=203.91.201.54 38 src=199.231.227.56 dst=14.139.241.89 38 src=199.231.227.56 dst=111.93.85.82 37 src=199.231.227.56 dst=65.52.0.56 Note: 1st column indicates the total number of connections to a particular IP. You have totally made more than 10k connections.

    Read the article

  • IPtables rate-limit, What are the differences between modules? Recent, Limit

    - by TechZilla
    I am doing some rate-limiting with IPtables, and i'm not sure if I should use "Recent" or "Limit" What are the differences between the two? If they both achieve the same result, which one has better performance? I would like to know, regardless if any difference would be perceivable. I am looking to ACCEPT if under limit, and REJECT if over. I'm not interested in thus bandwidth throttling, I don't want a queue. I don't need any syntax examples, both have ample use examples online. I have also used Limit in the past. I appreciate any responses.

    Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >