Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 100/287 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• CentOS listen to everything on the wire

  - by Poni

  I know there's a native command on linux that will output (to stdout) every "event" related to a certain network interface (be it eth0 etc'). Like there's tail -f <file> to listen on file changes.. I just can't find it. I want to see all events, incoming packets, even dropped ones. At lowest level possible. In every protocol (TCP, UDP etc'). I think WireShark is a bit too big for this as I need something very simple just to see the events, it's for testing. What's the command?

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• How to connect to a Virtualbox guest from the host when network cable unplugged

  - by Greg K

  I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• Why does just splitting an Ethernet cable not work?

  - by Sin Jeong-hun

  I thought the Ethernet is logically a one-line communication bus (for argument's sake, I am excluding hubs). All machines attached on the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why would splitting one Ethernet line from my home router into two and connecting two computers not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room, and I had put a computer in another room (also my room, though). Since a wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

  Read the article

• Cannot browse network shares in Windows Explorer, but paths are still accessible

  - by Jeff Lockhart

  Windows Explorer has somehow corrupted itself and I'm not sure how to fix this problem. My Windows installation has been in use for a few years with network shares setup and working. Recently, I noticed that a program that I use to save network share paths to a database was no longer opening the explorer window to browse the path. It usually opens to the last path saved, but now it was just not opening at all. When I go to Windows Explorer to browse the network share directly, I get the error \\SERVER is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The specified network provider name is invalid. The network shares are just shares on the server itself (once saved to the database, they're used on the server as well as clients to reach files). The strange thing is, the files are still accessible from the program that uses them if I type the network share path in manually. So it is only a problem with Windows Explorer browsing the path. The reason I think there is some sort of configuration or setting, possibly in the registry, corrupted is that when the problem first manifest itself, I was somehow able to open an explorer window to a network share path, but the breadcrumb in the address bar did not function properly. It duplicated the share name folder at the top of the breadcrumb stack and when I clicked the second of the duplicated share folder, it crashed explorer.exe. I haven't been able to browse any network share path since this happened. I have tried using the IP address directly \\192.168.1.# as well as \\localhost and neither of those work either. I have tried running sfc /scannow and it did not find any errors. I tried ipconfig /flushdns and this made no difference. Attempting to map the network share to a drive fails using either the explorer GUI or net use command. Is there some way to reset Windows Explorer somehow to resolve this? I'd really like to avoid reinstalling Windows entirely if I can.

  Read the article

• Disable Windows Update when on 3G network

  - by David Gardiner

  Are there any tools/utilities that will change Windows Update to not download when a machine is using a 3G-type wireless network connection? Not sure if there is any difference between using a 3G USB key and a tethered iPhone.

  Read the article

• How to share a USB modem?

  - by allenskd

  Usually I wouldn't have this problem if it was a dsl modem or cable modem but it's really been difficult for me to share this little modem to other computers. Right now I have my laptop connected to a hub, both computers are in the same workgroup and I have "share this computer internet to other computers"... etc. Problem is, I don't know what is currently happening... I'm hoping someone would guide me, I have googled and some people have been successful at sharing the connection but it seems I'm missing something =/ Let me know if you need any details, thanks

  Read the article

• Windows 2008 R2 server cannot access shares on other servers

  - by Rob

  I have a problem on my new 2008 R2 64-bit server. Essentially the server sometimes refuses to access shares on other server. in the format \\servernam\sharename sometime it works and then for a few hours it doesn't and then at randon it comes back online. This is a local AD network and have even put in a new gigabit switch between all server. All the old 2003 servers work fine so I know DNS and WINS is all ok. I get error 1006 in eventlog saying that my R2 server can't contact the domain controller when it clearly can. Just to add to the config, it is running on a Dell PowerEdge R410, Vmware Esxi 4.0 and R2 is configured as a terminal server. I can always view shares with FQDN This morning net view \\ did not work but net view \\ did. Very random and very frustrating. any ideas? thanks

  Read the article

• Network Printers

  - by Jack

  We have a sever that shares all the printers. The PC's that are running on XP professional get a error message quoting (Connect to Printer). The only way I can find to get around the problem is by restating the printer and as soon is it comes online you can then add it but you have not got long. do you think it could be anything to-do with updates on the sever? the sever system is running Windows Server 2003 any help would be much appreciated. Thanks

  Read the article

• Connecting Windows XP to Windows 7 directly using cable

  - by TPR

  These are the problems I am encountering. XP can access Windows 7, not the other way around (which is fine, because I don't need it the other way currently) File transfer is too slow like 0.031 MB/s even though netperf and netCPS list around 8-9 MB/s. I disabled firewall on both computers. Both are same workgroup. I left homegroup on Windows 7. Windows 7 sees the connection as unidentified network. 10.1.1.2 (XP) and 10.1.1.1 (Windows 7) Subnet mask 255.255.255.0 Default gateway and DNS are empty for both of them. Both computer are connected to internet using wireless (using home network), and both of them are connected to each other using wire! If anybody has any pointers, do let me know. I have no problem doing such setup with both computers being Windows 7. This time one of them is XP though, and that seems to be the problem.

  Read the article

• Internet connection sharing between Windows XP and Windows 7

  - by Dave

  I bought my lil sister's netbooks for Christmas and I've been having a heck of a time trying to get Internet Connection Sharing to work. The host computer is a Windows XP box and it uses a US Cellular 3G modem dongle thingy to set it's Internet access. Additionally I have a hard wire plugged into the LAN1 port of the router described below. (I tried the WAN port out of desperation but things didn't seem happy that way.) Additionally they have a linksys router (can't remember specific model number, I will find this out) that I was using to take advantage of it's wireless capabilities. Originally thought about updating the router to use dd-wrt, but after reading the instructions it looked like to much of a pita (had to downgrade firmware, then install dd-wrt) to set up, eventually I caved, out of desperation, and ended up successfully installing dd-wrt on the router. I have DHCP turned off on the router, actually all I could select was DHCP forwarder. The netbooks both have windows 7 starter installed on them. Initially, I had the networks joined to a homegroup but I dropped that and everyone is able to see everyone in their respective network explorers. When I turn on Internet Connection Sharing on the host, its IP on the LAN changed to 192.168.0.1, so I arbitrarily decided to assign the router to port 192.168.0.100. When I connect the netbooks they get IPs dynamically. As I stated before, everyone can see everyone in the network explorer, and shares can be accessed. The weird thing is that everyone can ping the router but they cannot ping each others IPs. The status on the netbooks says that there is no Internet Connectivity. Another thing I tried was manually setting the DNS servers on the netbooks to the DNS servers that the host computer has. The funny thing is when I ping an outside domain such as google.com the IP address resolves, however I get no responses from the pings. When I tried plugging the host into the WAN port I could ping the router, nor could I access the router's web access admin. Another thing I tried was turning off the firewall on the netbooks and the firewall off on the host computer for the LAN connection, and they still could not ping each other. Also I thought I should be able to start a remote desktop connection but I couldn't do that either, I also checked to make sure that computers would in fact accept a request for remote desktop connections.

  Read the article

• Finding cause of TCP retransmission within a LAN

  - by Surreal

  Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

  Read the article

• Windows 7 - Sharing a connection through WiFi?

  - by RadiantHex

  Hi folks, I have a PC with Win7 and an iPod touch. Win7 is connected to the internet through a 3G dongle, I have set up an Ad Hoc wifi network and ticked "Allow other network users to connect through this computer's Internet connection". I have connected to both networks, but I'm getting "No Internet access" as access type for the Ad Hoc connection. Any ideas?

  Read the article

• Intermittent connection issues with atheros ar9285

  - by MrStatic

  I have an asus K50IJ which has an atheros ar9285 wifi chip. It has decided to start to randomly drop internet. Although the card doesn't seem to notice it has. It will show full signal instead of say 3 bars. I tried to look at the atheros site for the latest driver but they don't even offer driver downloads. I then checked the asus site and it doesn't even list that card in the downloads for this laptop. I run Windows 7 64bit. It will drop either every minute or once a day while I am doing intensive bandwidth usage and when I am just idling.

  Read the article

• Connectiong adsl router/modem and router with bridgemode

  - by Zvonko Telefonko

  I have one adsl modem/router which is not "top" of the line and it lack allot of options which I need. I was able to acquire one Cisco router recently which has all options that I need ( like DMZ, VPN, port forwarding, etc). I'm interested, if I connect the old modem/router to new Cisco router using bridge mode, will I be able to use all the features on the Cisco? For instance, the old router is lacking of port forward options. Does this mean that I will not be able to use port forwarding on Cisco router either or, since I will be using bridge mode, this will not affect Cisco router and it will work as the modem is in him? thank you

  Read the article

• How can I selectively increase latency? E.g. throttle games

  - by Arcymag

  Basically, I want networked games to run poorly on a network, but I want everything else to run smoothly. I would also appreciate advice on blocking games in general. As far as I can tell, there's a few ways to completely prevent an internet game from running: Blocking entirely via DNS configuration (e.g. hosts file), or router DNS configuration Blocking entirely via a separate DNS server Blocking the application, by uninstalling or some kind of access control Blocking the application by automatically killing the process every once in a while Blocking the application by corrupting files periodically However, I would like a more subtle way to block a program. Something that either: Increases latency (would this be doable through some kind of QoS like what DD-WRT offers?) Increases latency by using a special routing configuration for specific target IPs Throttle other systems resources, such as memory, IO, or CPU Screw around with keyboard configurations when a game is launched I would like this to work on MacOSX and Windows, but Linux would be great too. FYI I don't have a kid, but I was brainstorming with some friends and parents.

  Read the article

• How to access internet from 2 laptops with data card plugged-in in one of the machine?

  - by learnerforever

  Hi, I have 2 laptops - one running Windows XP and other running Vista. Both have wifi card.I have one Reliance broadband data card. I want to be able to access internet on both the machines simultaneously using this one data card. Please help. I think, there would be many many ways to do it. I do have some linksys router but any simple quick way without any extra hardware? like we could set up p2p or WLAN between these 2 machines, because both have wifi card so we shouldn't compulsorily need any extra hardware(?) I am fine with connecting data card to either of the machines. Thanks,

  Read the article

• Configure VPN to access remote LAN network on Windows7

  - by PiotrK

  Situation: I have two Windows7 machines (PC and laptop). I've set PC as VPN server and laptop as VPN client using default built-in W7 network tools. I've disabled use default gateway in remote network on client machine, so client don't try to route all communication through VPN. I've routed port 1723 (TCP/UDP) on NAT to my server and enabled IPSec/PPTP/L2TP passthrough I've put my laptop in indepedent network (basically I've connected it via 3G network), connected to VPN server and checked ipconfig /all I've get: IP Address: 192.168.1.101 Mask: 255.255.255.255 Gateway: (none) LAN mask in server LAN network is 255.255.255.0 - I am surely missing something obvious, but Google doesn't give me any good advices; How can I access local LAN network from remote VPN client? How can I access local shared documents?

  Read the article

• Millions of SYN_RECV connections, no DDoS

  - by ThomK

  We have such server structure: reverse proxy (nginx) - worker (uwsgi) - postgresql / memcached. All servers are in local network behind router, with NATed external ip:ports (http/s 80/443 to proxy, and ssh 22 to all servers). Problem is, that sometimes proxy server netstat reports MILLIONS of SYN_RECV connections. From same IP / same ports. Like that: nginx ~ # netstat -n | grep 83.238.153.195 tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV tcp 0 0 192.168.1.1:80 83.238.153.195:3107 SYN_RECV [...] And this is not DDoS, because all IPs affected belongs to our website users. On side note, users says that it's not affecting them. Website is online and working, but... that particular one (from example above) told me that website is down and Firefox can't connect. I've done tcpdump. 19:42:14.826011 IP 83.238.153.195.zephyr-srv > 192.168.1.1.http: Flags [S], seq 1845850583, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:14.826042 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:17.887331 IP 83.238.153.195.zephyr-srv > 192.168.1.1.http: Flags [S], seq 1845850583, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:17.887343 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:19.065497 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:23.918064 IP 83.238.153.195.zephyr-srv > 192.168.1.1.http: Flags [S], seq 1845850583, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:23.918076 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:25.265499 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:37.265501 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:37.758051 IP 83.238.153.195.2107 > 192.168.1.1.http: Flags [S], seq 564208067, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:37.758069 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:40.714360 IP 83.238.153.195.2107 > 192.168.1.1.http: Flags [S], seq 564208067, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:40.714374 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:41.665503 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:46.751073 IP 83.238.153.195.2107 > 192.168.1.1.http: Flags [S], seq 564208067, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:42:46.751087 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:47.665498 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:42:59.865499 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:01.265500 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:13.320382 IP 83.238.153.195.2114 > 192.168.1.1.http: Flags [S], seq 2136055006, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:13.320399 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:16.320556 IP 83.238.153.195.2114 > 192.168.1.1.http: Flags [S], seq 2136055006, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:16.320569 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:17.665498 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:22.250069 IP 83.238.153.195.2114 > 192.168.1.1.http: Flags [S], seq 2136055006, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:22.250080 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:23.665500 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:23.865501 IP 192.168.1.1.http > 83.238.153.195.2107: Flags [S.], seq 3188568660, ack 564208068, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:35.665498 IP 192.168.1.1.http > 83.238.153.195.2114: Flags [S.], seq 3754336171, ack 2136055007, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:37.903038 IP 83.238.153.195.2213 > 192.168.1.1.http: Flags [S], seq 2918118729, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:37.903054 IP 192.168.1.1.http > 83.238.153.195.2213: Flags [S.], seq 4145523337, ack 2918118730, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:40.772899 IP 83.238.153.195.2213 > 192.168.1.1.http: Flags [S], seq 2918118729, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:40.772912 IP 192.168.1.1.http > 83.238.153.195.2213: Flags [S.], seq 4145523337, ack 2918118730, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:41.865500 IP 192.168.1.1.http > 83.238.153.195.2213: Flags [S.], seq 4145523337, ack 2918118730, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:46.793057 IP 83.238.153.195.2213 > 192.168.1.1.http: Flags [S], seq 2918118729, win 65535, options [mss 1412,nop,wscale 0,nop,nop,sackOK], length 0 19:43:46.793069 IP 192.168.1.1.http > 83.238.153.195.2213: Flags [S.], seq 4145523337, ack 2918118730, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:47.865500 IP 192.168.1.1.http > 83.238.153.195.2213: Flags [S.], seq 4145523337, ack 2918118730, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 19:43:49.465503 IP 192.168.1.1.http > 83.238.153.195.zephyr-srv: Flags [S.], seq 2835837547, ack 1845850584, win 5840, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 Anyone have some thoughts on that?

  Read the article

• CentOS 6.5 proxy bypass/no_proxy not working

  - by Naruto Uzumaki

  I am running CentOS 6.5 on my desktop. I've set the Network Proxy using the network proxy application provided under Preferences. I've also set the following exceptions: localhost,127.0.0.0/8,172.16.0.0/12,192.168.0.0./16 But whenever I am using wget (I'm testing the proxy settings using using wget) then wget tries to connect to the proxy for private addresses, but wget localhost works fine and doesn't use the proxy. I also removed all the proxy settings and set the proxy in the shell: export http_proxy="<proxy_url>:<port>" export https_proxy="<proxy_url>:<port>" export no_proxy="localhost,127.0.0.0/8,172.16.0.0/12,192.168.0.0./16" It work when I use the command wget <external_url> or wget localhost but fails when I use the command wget <private address from the $no_proxy variable>. I also tried setting the variables in Ubuntu 14.04 also and facing the same issue. Regards,

  Read the article

• Setup for a live (low-latency) audio video broadcast over Wi-Fi?

  - by Majal Mirasol

  The Upgrade We are capturing audio (from mixer) and video (from a camera) from a main auditorium and passing it to separate rooms within the building. We used to have done this via manual audio/video cables and wires. We wanted to "upgrade" the system and wirelessly broadcast the stream via Wi-Fi. The Problem In our current setup (Wirecast running on A10 on a Wireless-N network), we have the problem of delay. Our streams are delayed from a minute up to five minutes on the clients (laptop/iPad/Android). This had not been a problem from the previous wired connections. Since the wireless network is local, we thought that a delay of less than a second should be achievable. Our Question And so it goes. Anybody there who has any experience for a setup that has both low latency and at the same time user-friendly to clients streaming in the program? Any recommendations would be highly appreciated. (Our current setup in on Windows 7, but setup on a dedicated Linux box is preferred, if achievable.)

  Read the article

• Monitor HTTP usage on network from Linux free

  - by David

  I manage a small office network. I am looking to start monitoring/logging internet usage (website requests) for each user on a small network. All the windows clients are running through a switch to a BT router. I also have a linux (centos) machine which is connected as a client to the BT router as well. Is there any free software I can install on the linux box (or my own machine) to allow me to log and monitor websites requested by users kind of like browser history. Ideally, something that would collect each client's browser history in 1 place. Thanks

  Read the article

• Western Digital My Book World drops off network

  - by Macha

  Most of my storage in my house relies on a WD My Book World Edition 500GB network drive. I threw out the vendor crapware they give you to access it (a trial version of Mionet) after it starting nagging me to upgrade, and set it up as a standard network drive using Window's Map Network Drive. However, since then, it has been dropping off the network after 30 minutes of non-usage. The only way to get it back on is to switch it off and on again at the plug socket. Does anyone know what is causing this, and hopefully how to fix it? EDIT: it's the original "blue rings" version with the latest firmware.

  Read the article

• Fedora 17 - Can't access remote machine using hostname

  - by Aaron

  I am using Fedora 17 and am trying to access a remote machine (running Fedora 15) using its hostname which isn't working. The machine is right next to me on the same switch as my machine (so they are both on the same network with the same subnet and everything). When I was running Windows (7 32-bit) on my machine I could access the other machine no problem but now that I am running Fedora 17 that's not the case. Is there an additional daemon or something that I need to be using in order for this to work?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >