Search Results

Search found 66534 results on 2662 pages for 'document set'.

Page 1004/2662 | < Previous Page | 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011  | Next Page >

• error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)

  - by ArunS

  We have online shopping site. When I am going to checkout page i am getting a error like this "error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure(35)" From the apache error log i can see some attempts to connect to api.paypal.com. Here is the part of my apache error log * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.123... * connected * Connected to api.paypal.com (66.211.168.123) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 When i tried to connect to api.paypal.com using curl i am getting a error like this curl -iv https://api.paypal.com/ * About to connect() to api.paypal.com port 443 (#0) * Trying 66.211.168.91... connected * Connected to api.paypal.com (66.211.168.91) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Request CERT (13): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS alert, Server hello (2): * error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure * Closing connection #0 curl: (35) error:14094410:SSL routines:SSL3_READ_BYTES:sslv3 alert handshake failure Can anyone help me to figure out this. Thanks in Advance. Arun S

  Read the article

• Widespread misinterpretation of DNS rules in resolving wildcards

  - by Dominic Sayers

  [EDITED to add: This problem has gone away on its own. I believe Cloudflare's name resolution may have been to blame. See my own answer below] Here is a snippet of my zone file *.example.com. 300 IN CNAME proxy.herokuapp.com. foo.example.com. 300 IN A 111.111.111.111 If I dig @8.8.8.8 foo.example.com I get the answer I expect: ;; ANSWER SECTION: foo.example.com. 30 IN A 111.111.111.111 The same is true of all other public DNS servers I've tried. However, when I try to set up a check with Pingdom to a URL on foo.example.com it instead sends the traffic to my Heroku app referenced by the *.example.com RR. The same is true of checks set up on New Relic, Errplane and traffic generated by the Heroku app itself. So on the one side, all public DNS servers interpret the zone file one way. Yet four service providers all interpret it a different way, one that differs to the standard suggested by RFC 4592. My question is: are these reputable, mature service providers all wrong? Or is it little me?

  Read the article

• Basic OpenVPN setup

  - by WalterJ89

  I am attempting to connect 2 win7 (x64+ x32) computers (there will be 4 in total) using OpenVPN. Right now they are on the same network but the intention is to be able to access the client remotely regardless of its location. The Problem I am having is I am unable to ping or tracert between the two computers. They seem to be on different subnets even though I have the mask set to 255.255.255.0. The server ends up as 10.8.0.1 255.255.255.252 and the client 10.8.0.6 255.255.255.252. And a third ends up as 10.8.0.10. I don't know if this a Windows 7 problem or something I have wrong in my config. Its a very simple set up, I'm not connecting two LANs. this is the server config (removed all the extra lines because it was too ugly) port 1194 proto udp dev tun ca keys/ca.crt cert keys/server.crt key keys/server.key # This file should be kept secret dh keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 6 this is the client config client dev tun proto udp remote thisdomainis.random.com 1194 resolv-retry infinite nobind persist-key persist-tun ca keys/ca.crt cert keys/client.crt key keys/client.key ns-cert-type server comp-lzo verb 6 Is there anything I missed in this? keys are all correct and the vpn's connect fine, its just the subnet or route issue. Thank You

  Read the article

• How can I make the XAnalogTV xscreensaver fill my screen?

  - by Breakthrough

  I recently installed xscreensaver, as well as the additional/extra screensavers. Many of the OpenGL ones function correctly, going fullscreen as expected. However, for some reason, the XAnalogTV screensaver leaves two "blank" spots on the edges of my screen. If I manually launch XAnalogTV, it displays a window, which it fills correctly. When I maximize the window, the same effect occurs: the window maximizes, but the two edges of the screen are literally "transparent". This effect also occurs when the screensaver is set to fullscreen. For these reasons, I believe the problem may be related to the aspect ratio of the screen. The edges of the screen are literally "ignored", with nothing being drawn there. Specifically, note the transition between the maximized and full-screen screenshots (with the un-drawn whitespace shrinking as the vertical height has been increased). For reference, I am running Xubuntu 12.04 on a Dell Vostro 1520 (Intel P8600, Nvidia 9300M) with a 1440 x 900 display (16:10). I have also set the GetViewPortIsFullOfLies preference to true. Is there any way to force XAnalogTV to fill my entire screen? Alternatively, as I believe the problem is aspect-ratio related, is there any way I can get the screensaver to render larger than my display, and simply discard the extra pixels? Relevant screenshots (windowed, maximized, and full-screen, respectively): You can see in the last two that the scrollbar from Firefox is clearly visible, even though this is a full-screen screensaver.

  Read the article

• (Mac Intel) HP PS driver prints in B&W from Adobe Reader after installing Cannon PS driver

  - by JohnB

  I have a unique problem that leaves me at a loss as to where to start troubleshooting. We have three Macs we use for graphics, two of which are PowerPC and one which is Intel. They are set up to print to an HP 5500dn, but occasionally this printer gets tied up with a massive print job, so I installed the PS driver (iR-PSv1.81MacOSX) for the Cannon C3200 Printer/copier on each of the machines. Both of the PowerPC Macs installed without issue, but the Intel Mac exhibits strange behavior: I've confirmed that while the Cannon driver is installed (whether or not the Cannon is set up for printing in print settings), the HP 5500dn will print in color from Safari, but only prints in black and white from Adobe Reader. The Cannon printer itself has not exhibited any strange behavior As soon as the Cannon driver is uninstalled, the HP 5500dn prints in color from Adobe Reader again. We run a network of Windows PCs, and the 'Mac room' mostly takes care of itself, so we don't have any experienced Mac administrators onsite. The Cannon is capable of Appletalk, but the PS driver seemed easier to work with (and Appletalk is currently disable on the Cannon. I'm not against using the Appletalk compatible drivers, but I would rather use the PS driver if at all possible - I don't want to open up the proverbial can of worms. If someone has any clues or suggestions that would help troubleshoot this problem, I would be grateful. I've already done some googling, but due to the obscure nature of this problem, I haven't been very successful. I don't like to create multiple threads on multiple sites, but I'm posting here due to Chopper3's suggestion on my post on ServerFault (http://serverfault.com/questions/135349/mac-intel-hp-ps-driver-prints-in-bw-from-adobe-reader-after-installing-cannon)

  Read the article

• How do I connect a 2008 server to a 2003 server active directory?

  - by Matt

  Our DC is running Windows Server 2003. I've just set up Windows Server 2008 and have terminal server running on it. When setting the terminal server permissions, it was able to allow a group name that was read from the domain. In the DC the new terminal server shows up as a computer in the domain. I can also log in as a user within the domain even though that user doesn't exist locally on the new server. However, when I go to set sharing permissions on the new machine it doesn't show my domain as a location. Instead it is only looking at location "machinename" and not allowing domain to be seen or added. Is there something I'm missing? Ok, lots of errors in the event log. We have this: The winlogon notification subscriber is taking long time to handle the notification event (Logon). Followed by this: The winlogon notification subscriber took 121 second(s) to handle the notification event (Logon). Followed by: The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has succesfully processed. If you do not see a success message for several hours, then contact your administrator. I think this might be the same problem I'm having http://serverfault.com/questions/24420/primary-domain-controller-slow Solved. The issue was that I had changed from DHCP to static and put the wrong DNS server IP in. i.e. firewall instead of DC/DNS server.

  Read the article

• Windows Virtual Machines will not run

  - by jlego

  I'm trying to setup a few virtual machines to use for testing websites in the various old versions of IE. I had Microsoft Virtual PC working on an older machine using XP mode and 2 other VHD's from Microsoft that allowed me to test in IE6-IE8. I've recently gotten a new work machine and am trying to set up the VMs again for testing, however nothing seems to be working. Both the old and the new system run Windows 7 64-bit Ultimate with AMD processors. I downloaded Virtual PC & XP mode from here http://www.microsoft.com/windows/virtual-pc/download.aspx and go through the installation process. XP mode is installed, but when I try to run it it goes through the initial setup process only to fail when it is almost complete with the error "Cannot Complete Setup". (After googling I see that this might be a conflict with my processor) I download other VHD's from here http://www.microsoft.com/windows/virtual-pc/download.aspx in order to get the other versions of IE and try to set those up in Virtual PC as well. I click on them to start the machine and both Windows 7 with IE8 and Windows Vista with IE7 just hang at a black screen. I try to use Virtual Box instead, and I get Windows XP with IE6 running, but I have no internet connection in the VM. I try all different settings and try to google the correct settings but nothing seems to work. When I load the VM, XP shows that its found new hardware but it needs the drivers. One of these pieces of hardware is the network adapter, but I can't connect to the internet to download the driver in the guest OS. VirtualBox tells me I need to install extensions in order for things to function properly. I go through the installation process in the guest OS and restart the VM, however now XP is asking for validation and I can't access the VM. I try installing the other 2 OS (Vista & 7) but I get a BSOD right after the startup screen appears and the VM restarts itself. I'm getting so frustrated trying to make this work, I would really appreciate any assistance on getting the VMs up and running or any alternatives for testing websites in Internet Explorer.

  Read the article

• pgpoolAdmin keeps going straight back to it's login page

  - by user705142

  I'm trying to run pgpoolAdmin through nginx - it seems to be working properly, at least initially. I've gone through the initial set-up, which works fine, but now after logging in every link takes me straight back to the login page. It also shows japanese text instead of english, despite picking english in the installation. It seems to me just as if it was unable to save any user data, session information etc. I have javascript/cookies enabled, so it's not that. The ownership of the folder is nginx, and so too is pgmgt.conf.php, so it shouldn't be a problem with permissions. One potential issue is that I can't seem to see any confirmation that php postgresql support is enabled in the php info screen, despite the correct package installed and in the config line. Any ideas as to what's happening here? The nginx rules are pretty standard: server { # pg-pool admin listen 997; server_name localhost; root /opt/pgpooladmin; index index.php; location ~ .php$ { fastcgi_pass_header Set-Cookie; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; include fastcgi_params; } }

  Read the article

• Windows 7 - Windwos XP - sharing - why isn't working?

  - by durumdara

  Hi! This is seems to be "hardware" and not "software" / "programming" question, but I need to use this share in my programs, so it is "close to programming". We had an XP based wireless network. The server is XP Professional, the clients are XP Home (Notebooks). This was working well with folder sharing (with user rights, not simple share). Then we replaced the one of the notebook with Win7/X64 notebook. First time this can reach the server, and the another client too. Later I went to another sites, and connect to another servers, another networks. And then, when I return to this network, I saw that I cannot connect to this server. Nothing of resources I see, and when try to dbl click on this computer, I got login window, where I can write anything, never I can login... The interesting part, that: Another XP home can see the server, can login as quest, or with other user. The server can see the XP home notebook. The Win7 can see the notebook's shared folders, and XP home can see the Win7 shared folders. The server can see the Win7 folders, BUT: the Win7 cannot see the server folders. Cannot see the resources too... The Win7 is in "work networking group", the group name is not mshome. I tried everything on the server, I tried to remove MS client, restore it with simple sharing, set guest password, etc., but I lost the possibilities to access this server from Win7. Does anyone have any idea what I need to see, what I need to set to access these resource - to use them in my programs? Thanks for every info, link: dd

  Read the article

• Either, nginx+php-fpm bad config or nginx+php-fpm cannot handle high query?

  - by The Wolf

  I have wordpress installed in my server configured(hopefully with nginx+php-fpm+mariaDB). I am trying to import using wordpress importer a 1.5MB xml file. Everytime I try to upload it using the importer, it got cut of... meaning just blank screen result.. Here is my error log: actually I just posted 2 of the errors [error] 858#0: *1 connect() failed (111: Connection refused) while connecting to upstream, client: xx.xxx.xx.xx, server: xxx.com, request: "GET xxxx.html HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" [error] 858#0: *13 connect() failed (111: Connection refused) while connecting to upstream, client: xxx.x.xx.xx, server: xxx.com, request: "GET xxxx.php HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "xxx.com" I don't know what is the reason why it can't process the wordpress export .xml. I already increased max_file_upload & etc., but nothing happens. Hope somebody can help me. Here are my conf: nginx.conf user nginx; worker_processes 8; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; server_tokens off; keepalive_timeout 65; fastcgi_read_timeout 500; #gzip on; client_max_body_size 2M; php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. include=/etc/php-fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Default Value: none pid = /var/run/php-fpm/php-fpm.pid ; Error log file ; Default Value: /var/log/php-fpm.log error_log = /var/log/php-fpm/error.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf [root@host etc]# vim php-fpm.conf [root@host etc]# vim php-fpm.conf ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes daemonize = no ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf ps aux [root@host etc]# ps aux USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.1 2900 1380 ? Ss Jun02 0:00 init root 2 0.0 0.0 0 0 ? S Jun02 0:00 [kthreadd/9308] root 3 0.0 0.0 0 0 ? S Jun02 0:00 [khelper/9308] root 124 0.0 0.0 2464 576 ? S<s Jun02 0:00 /sbin/udevd -d root 460 0.0 0.1 35976 1308 ? Sl Jun02 0:00 /sbin/rsyslogd -i /var/run/syslogd.pid -c 5 root 474 0.0 0.0 8940 1028 ? Ss Jun02 0:00 /usr/sbin/sshd root 481 0.0 0.0 3264 876 ? Ss Jun02 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid root 491 0.0 0.1 6268 1432 ? S Jun02 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/host.busilak.com. mysql 584 0.1 6.8 679072 71456 ? Sl Jun02 0:04 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib/mysql/plugin --use root 586 0.0 0.3 12008 3820 ? Ss Jun02 0:01 sshd: root@pts/0 root 629 0.0 0.0 9140 756 ? Ss Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 630 0.0 0.0 9140 520 ? S Jun02 0:00 /usr/sbin/saslauthd -m /var/run/saslauthd -a pam -n 2 root 645 0.0 0.1 12788 1928 ? Ss Jun02 0:01 sendmail: accepting connections smmsp 653 0.0 0.1 12576 1728 ? Ss Jun02 0:00 sendmail: Queue runner@01:00:00 for /var/spool/clientmqueue root 691 0.0 0.1 7148 1184 ? Ss Jun02 0:00 crond root 698 0.0 0.1 6272 1688 pts/0 Ss Jun02 0:00 -bash root 1006 0.0 0.0 7828 924 ? Ss 00:30 0:00 nginx: master process /usr/sbin/nginx -c /etc/nginx/nginx.conf nginx 1007 0.0 0.1 8156 1724 ? S 00:30 0:00 nginx: worker process nginx 1008 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1009 0.0 0.1 8020 1356 ? S 00:30 0:00 nginx: worker process nginx 1011 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1012 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1013 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1014 0.0 0.1 8024 1360 ? S 00:30 0:00 nginx: worker process nginx 1015 0.0 0.1 8024 1344 ? S 00:30 0:00 nginx: worker process root 1030 0.0 0.2 25396 2904 ? Ss 00:30 0:00 php-fpm: master process (/etc/php-fpm.conf) apache 1031 0.0 1.9 40700 20624 ? S 00:30 0:00 php-fpm: pool www apache 1032 0.0 2.0 41924 21888 ? S 00:30 0:01 php-fpm: pool www apache 1033 0.0 1.9 41212 20848 ? S 00:30 0:01 php-fpm: pool www apache 1034 0.0 1.9 40956 20792 ? S 00:30 0:01 php-fpm: pool www apache 1035 0.0 2.0 41560 21556 ? S 00:30 0:02 php-fpm: pool www apache 1040 0.0 1.8 39292 19120 ? S 00:30 0:00 php-fpm: pool www root 1125 0.0 0.0 6080 1040 pts/0 R+ 01:04 0:00 ps aux netstat -l [root@host etc]# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 localhost.localdomain:smtp *:* LISTEN tcp 0 0 localhost.locald:cslistener *:* LISTEN tcp 0 0 *:mysql *:* LISTEN tcp 0 0 *:http *:* LISTEN tcp 0 0 *:ssh *:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 60575947 /var/run/saslauthd/mux unix 2 [ ACC ] STREAM LISTENING 60574168 @/com/ubuntu/upstart unix 2 [ ACC ] STREAM LISTENING 60575873 /var/lib/mysql/mysql.sock Hope somebody can help me to figure out what is the problem.

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• How seriously should I take ECC correctable error warnings?

  - by David Mackintosh

  I have a pile of Sun X2200-M2 servers. These servers have ECC memory. In some of these servers, I am getting warnings in the eLOM about "correctable ECC errors detected", eg: # ssh regress11 ipmitool sel elist 1 | 05/20/2010 | 14:20:27 | Memory CPU0 DIMM2 | Correctable ECC | Asserted 2 | 05/20/2010 | 14:33:47 | Memory CPU0 DIMM2 | Correctable ECC | Asserted ...some more frequently than others. The kernel on this particular system is throwing EDAC errors as well, although with far more frequency than the eLOM is recording ECC events: EDAC k8 MC0: general bus error: participating processor(local node response), time-out(no timeout) memory transaction type(generic read), mem or i/o(mem access), cache level(generic) MC0: CE page 0x42a194, offset 0x60, grain 8, syndrome 0xf654, row 4, channel 1, label "": k8_edac MC0: CE - no information available: k8_edac Error Overflow set EDAC k8 MC0: extended error code: ECC chipkill x4 error EDAC k8 MC0: general bus error: participating processor(local node response), time-out(no timeout) memory transaction type(generic read), mem or i/o(mem access), cache level(generic) MC0: CE page 0x48cb94, offset 0x10, grain 8, syndrome 0xf654, row 5, channel 1, label "": k8_edac MC0: CE - no information available: k8_edac Error Overflow set EDAC k8 MC0: extended error code: ECC chipkill x4 error Now if the server is detecting Uncorrectable ECC, the system resets, so clearly that's bad and removing/replacing the identified stick or pair corrects the issue. But I am thinking that if the error is Correctable, then there's no immediate issue -- I can treat this as a warning and be prepared to pull the stick/pair if an uncorrectable error starts occurring?

  Read the article

• How to move a sata drive to a machine without AHCI mode

  - by Andrew Cooper

  I've got a Dell Inspiron 1545 on which the screen has died. I'm able to plug an external monitor into the Inspiron 1545 and it works fine, so the screen is the only issue. The OS is Win7. I'm trying to move the disk to a spare Dell Precision M90 laptop that I've got lying around. The problem is that almost as soon as the Windows logo appears in the boot sequence I get a BSOD with a STOP 0x0000007B message. Researching this message pointed to issues with SATA AHCI mode. I looked in the BIOS of the Inspiron 1545 and the controller was set to AHCI mode. I set it to ATA mode and tried to boot with the same drive and got the same result as on the Precision M90. Switching back to AHCI allowed the machine to boot correctly again. I checked the BIOS on the Precision M90 and it doesn't seem to support AHCI mode, although it is a SATA controller onboard. The BIOS is the latest A08 version available from Dell. Is there any way I can get this drive to boot in the M90 without reformatting it?

  Read the article

• Unix Permissions: Enable access to files no matter the user?

  - by TK Kocheran

  I've been using Linux for a long time and I still am completely in the dark about how file permissions really work. With that in mind, does anyone have any books or thorough guides I could read to really understand things completely? I've done my fair share of sysadminning, so I know the easy stuff like making directories readable and writable, making files executable, and changing the owner of a file, but on sharing files across users, I'm lost. Here's my main problem. I have a number of machines across which I intend to synchronize my music library. I've been using Unison for a while now and it's a great choice as I can easily run it over SSH on my local network which I just set up. Win-win. Up until this point, I've been synchronizing computers using a 2TB external hard drive. (computer 1 unisons to HD, computer 2 unisons to HD, etc.) This is tedious at best, especially since I encrypted the drive, making it a huge hassle to hook it up to all of my machines and sync it. Anyway, the drive is running ext4 (in TrueCrypt), so it maintains all Unix filesystem info like owners and groups. I just set up a new machine and just Unison'd it to get the music on it, and I realized that now, all of my permissions are fubar. I had to run Unison as root since that was the only way I could get the files to come off of the external drive. Apparently, since I'm using a different user name on this machine than my usual "rfkrocktk" across all machines, this essentially throws a huge wrench in the gears. Here's my use case. This laptop has two effective users, "leandra" and "rfkrocktk". I want to share music between these two users, so I symlinked /home/rfkrocktk/Music to point to /home/leandra/Music. How do I (a) allow both users access to read/write/delete files in this folder, and (b) keep everything nicely in sync without messing up file ownership?

  Read the article

• Losing JSESSIONID when using ProxyHTMLURLMap

  - by Matthew Schmitt

  I've setup a reverse proxy between an Apache front-end and multiple Tomcat backends. The below block of code includes the ProxyHTMLURLMap param so that the HTML can be rewritten to remove the Tomcat context path. With this setup in place, after logging into my application, an initial JSESSIONID is set properly, but when navigating to any other page, this JSESSIONID is lost and another one is set by the application. I should mention that the initial login directs to a URL that includes the current context path (i.e. https://app.domain.com/context/home), but when navigating to another page, that context path is not present in the URL (i.e. https://app.domain.com/page2). <Proxy balancer://happcluster> BalancerMember ajp://happ01.h.s.com:8009 route=worker1 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ02.h.s.com:8009 route=worker2 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ03.h.s.com:8009 route=worker3 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ04.h.s.com:8009 route=worker4 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ05.h.s.com:8009 route=worker5 loadfactor=5 timeout=15 retry=5 ProxySet lbmethod=bytraffic ProxySet stickysession=JSESSIONID </Proxy> ProxyPass /context balancer://happcluster/context ProxyPass / balancer://happcluster/context/ <Location /context/> # Rewrite HTTP headers and HTML/CSS links for everything else ProxyPassReverse / ProxyPassReverseCookieDomain / app.domain.com ProxyPassReverseCookiePath / /context ProxyHTMLURLMap /context/ / # Be prepared to rewrite the HTML/CSS files as they come back # from Tomcat SetOutputFilter INFLATE;proxy-html;DEFLATE </Location> Has anyone ever run into a similar situation?

  Read the article

• Two hosted servers, one public - VPN?

  - by Aquitaine

  Hello there, Web developer here who has to occasionally wear a system & network admin hat (small company). We currently have a single hosted server running Windows Server 2003 that runs both our web server (IIS/Coldfusion) and our database server (SQL Server 2008). We lock down the SQL server by allowing only specific IPs to connect to it. Not ideal but it's worked thus far. We're moving up to two distinct servers and I want to take the opportunity to 'get things right' and make only the web server face the public. What I need to be able to do is to allow only a handful of people to connect to the database server. Rather than using an IP allow list, I'd prefer to use a VPN to let people through so that access is based on the user and not simply the user's location. I'm leaning toward something like OpenVPN, just so I can stick with Server 2008 Web edition. Do I: Use the web server as a VPN server and set up the database server to only accept connections from the web server? Is there an extra step required to make connections to, say, db.mycompany.com route through the VPN rather than through a different connection? I'm ignorant of this part of network infrastructure stuff. Or, Set up a VPN server on the database server as the only public-facing server connection so that there aren't any routing issues to deal with? I know this is Network 101 stuff but I thought I'd ask before just blundering through it since it could affect the company a bit. Thanks very much!

  Read the article

• Haproxy not properly passing on X-Forwarded-For header

  - by JesseP

  I have backend web servers that receive requests by way of haproxy-nginx-fastcgi. The web app used to see multiple ip's coming through in the X-Forwarded-For header, chained together with commas (most original IP on the left). At some point in the recent past (just noticed, so not sure what caused it) something changed, and now I'm only seeing a single IP passed in the header to my web application. I've tried with haproxy 1.4.21 and 1.4.22 (recent upgrade) with the same behavior. Haproxy has the forwardfor header set: option forwardfor Nginx fastcgi_params config defines this header to be passed to the app: fastcgi_param HTTP_X_FORWARDED_FOR $http_x_forwarded_for; Anyone have any ideas on what might be going wrong here? EDIT: I just started logging the $http_x_forwarded_for variable in nginx logs, and nginx is only ever seeing a single IP, which shouldn't ever be the case, as we should always see our haproxy ip added in there, right? So, issue must either be in nginx handling of the variable coming in, or haproxy not building it properly. I'll keep digging... EDIT #2: I enabled request and response header logging in HAProxy, and it is not spitting anything out for X-Forwarded-For, which seems very odd: Oct 10 10:49:01 newark-lb1 haproxy[19989]: 66.87.95.74:47497 [10/Oct/2012:10:49:01.467] http service/newark2 0/0/0/16/40 301 574 - - ---- 4/4/3/0/0 0/0 {} {} "GET /2zi HTTP/1.1" O Here are the options i set for this in my frontend: mode http option httplog capture request header X-Forwarded-For len 25 capture response header X-Forwarded-For len 25 option httpclose option forwardfor EDIT #3: It really seems like haproxy is munging the header and just passing on a single one to the backend. This is fairly impacting to our production service, so if anyone has an ideas it would be greatly appreciated. I'm stumped... :(

  Read the article

• Why doesn't the Windows 7 volume mixer remember per-application levels for all applications?

  - by mdives

  If I have the device's master level set to 50, and then lower an application level to 25; Once I close that application and reopen it, the volume levels should persist. The master level should remain at 50 and the application's at 25. This does happen for most applications. However, for one in particular, Napster, it does not. I subscribe to Napster's streaming service. I use the Napster desktop application to connect to that service. Every time that I open the Napster app, I have to adjust the application's volume level down in the volume mixer. When I open the app again after closing it, I have to do the same thing, the volume mixer is not remembering the set level. In fact. The level is reset back to 50, the same level as the device's master level. Has anyone else experienced this, with Napster or any other application? Is there a solution or is this a known issue?

  Read the article

• install Win7 SP1 with bcdedit failing

  - by Albert

  I'm getting the error 0x800F0A12 which is described here. bcdedit says: C:\>bcdedit.exe Der Speicher für die Startkonfigurationsdaten konnte nicht geöffnet werden. Das System kann die angegebene Datei nicht finden. (English: Couldn't open the start configuration. Couldn't find the file.) (off topic: how can I get those messages in English?) I played around and I assume that is because the system partition C:\ is not on the first BIOS disk. There are 4 disks in my PC. On one of them (shown as the 4th in Windows drive manager) contains Windows, whereby the system-reserved NTFS partition is the first primary and the second primary is my main Windows system partition. A few more partitions follow with other (non-NTFS) stuff. I was able to set the first two disks offline (via the Windows drive manager). For the 3rd disk, it says that it cannot set the BIOS 0 disk offline. How can I ignore that and still install SP1? I don't want to rewire/resetup my disks.

  Read the article

• How to configure multiple virtual hosts for multiple users on Linux/Apache2.2

  - by authentictech

  I want to set up a virtual hosting server on Linux/Apache2.2 that allows multiple users to set up multiple website domains as would be appropriate for commercial shared hosting. I have seen examples (from my then perspective as a shared hosting customer) that allow users to store their web files in their user home directory with directories to correspond to the virtual host domain, e.g.: /home/user1/www/example1.com /home/user2/www/example2.com instead of using /var/www Questions: How would you configure this in your Apache configuration files? (Don't worry about DNS) Is this the best way to manage multiple virtual hosts? Are there others? What safety or security issues do you think I should be aware of in doing this? Many thanks, folks. Edit: If you want to only answer question 1, please feel free, as that is the most urgent to me at this moment and I would consider that an answer to the question. I have done it for myself since posting, but I am not confident that it's the best solution and I would like to know how an experienced sysadmin would do it. Thanks.

  Read the article

• Cacti is ignoring hash marks in interface aliases

  - by Matt Simmons

  I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

< Previous Page | 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011  | Next Page >