Search Results

Search found 29317 results on 1173 pages for 'device control'.

Page 1015/1173 | < Previous Page | 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022  | Next Page >

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Port 22 is not responding

  - by Emanuele Feliziani

  I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

  Read the article

• Linux: prevent outgoing TCP flood

  - by Willem

  I run several hundred webservers behind loadbalancers, hosting many different sites with a plethora of applications (of which I have no control). About once every month, one of the sites gets hacked and a flood script is uploaded to attack some bank or political institution. In the past, these were always UDP floods which were effectively resolved by blocking outgoing UDP traffic on the individual webserver. Yesterday they started flooding a large US bank from our servers using many TCP connections to port 80. As these type of connections are perfectly valid for our applications, just blocking them is not an acceptable solution. I am considering the following alternatives. Which one would you recommend? Have you implemented these, and how? Limit on the webserver (iptables) outgoing TCP packets with source port != 80 Same but with queueing (tc) Rate limit outgoing traffic per user per server. Quite an administrative burden, as there are potentially 1000's of different users per application server. Maybe this: how can I limit per user bandwidth? Anything else? Naturally, I'm also looking into ways to minimize the chance of hackers getting into one of our hosted sites, but as that mechanism will never be 100% waterproof, I want to severely limit the impact of an intrusion. Cheers!

  Read the article

• How should I configure nginx caching headers for a "baked" static file blog? (Octopress)

  - by Doug Stephen

  I recently deployed an Octopress blog (which is a blogging platform built around Jekyll). It's a static-site blog generator, with no dynamic content or databases to muck about with. It's being served up by nginx. My question is, what is the appropriate expires directive or Cache-Control header that I should set to make sure that visitors get the most up-to-date version of the site when they visit without having to manually refresh? Since the site is just .html files it seems to get cached pretty aggressively. I've tried a million different combinations of expires modified + xxxx and even straight up expires off but I can't seem to wrap my head around it. I'm very new to dealing with caching like this, specifically, on static files that change frequently, and obviously if the site hasn't been changed then I'd like for it to be served up out of the cache. Update (still not solved though): I found open_file_cache, tweaked that. Still no dice. It seems like what I might want to do is use nginx as a proxy cache and use Apache with ETags? Is there really no convenient way to make nginx play nicer with conditional requests from the client? TL;DR: I'm running a static-file blog and I'd like to set up nginx to only serve from the cache if the blog hasn't been updated recently, but I'm too stupid to figure it out myself because I'm relatively new to web servers.

  Read the article

• Too many concurrent connections Exchange 2010. What else is there to check?

  - by hydroparadise

  I thought that I had this under control before. But for some reason during our last email marketing promo, I start receiving from our mass email client (built in house).. The message could not be sent to the SMTP server. The transport error code is 0x800ccc67. The server repsonse was 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel again. There's several places I've checked to make sure that wouldn't be an issue. First I checked that receive connector was set to receive an adequate number of connections on our relay connector (1000 connections). Then, I would later find out about Throttling Policies. I created one and set all the properties I knew to set in terms of the policy following properties to 1000; EWSMaxConcurrency, OWAMaxConcurrency, CPAMaxConcurrency, and CPAMaxConcurrency. Still, the email client starts receiving the error shortly after 100 has been sent and takes about 15-30 seconds. The process is then repeatable, but still the error gets received at the same spot everytime. Is there a rate setting that I am missing? Was there a windows update that I missed looking at? Should the software have it's own throttling feature?

  Read the article

• DVD playback with Windows Media Player 11 works fine, but when copied to HDD and then played back, t

  - by stakx

  I have several DVDs with short documentaries on it. Since the notebook I'm using (a Dell Latitude E6400) has only one DVD drive, and I might play back those short movies very often, I thought of copying them to the HDD and playing them back from there. However, I've run into a problem, namely stuttering audio. Problem description: When I play back these movies directly from DVD (with Windows Media Player 11 under Windows Vista), everything works fine. Smooth video, no significant audio problems (only the occasional click). But as soon as I copy any of these DVDs to the HDD and try to play them back from there (e.g. using the wmpdvd://drive/title/chapter?contentdir=path protocol, I get stuttering audio — audio playback sounds like a machine gun for a third of a second or so, approx. every 8 seconds. I have tried converting the VOB files from the DVD to another format (ie. ripping), but that resulted in a noticeable downgrade of picture quality. Therefore I thought it best to keep the files in their original format, if possible. Still, I suspect that the stuttering audio is due to some (de-)muxing problem, and that changing the file format might help. (After all, video playback is fine; therefore I don't think that the hardware is too slow for playback.) Only thing is, I don't know how to convert the VOB files to another Windows Media Player-compatible format without quality loss. I hope someone can help me, or give me further pointers on things I could try out to get HDD playback to work without the problem described. Some things I've tried so far, without any success: VOB2MPG, in order to convert the .vob file to a .mpg file. But that changes only the A/V container, not the content. No re-encoding takes place at all. Re-encoding with MPlayer/MEncoder. Lots of quality loss there, and I frankly haven't got the time to test all possible settings combinations available. Disabling all plug-ins, equalizers, etc. in Windows Media Player. Disabling all hardware acceleration on the audio playback device. Further info on the VOB files I'm trying to playback: The video format is MPEG ES, PAL 720x576 pixels @ 24/25 frames per second. The sound stream is uncompressed PCM, 16-bit stereo @ 48kHz. (Might it help if I somehow re-encoded the sound stream at a lower resolution, or as an MP3? If so, how would I do this without changing the video stream?) P.S.: I am limited to using Windows Media Player (11). (I previously tried MPlayer btw., but the video playback quality was surprisingly bad.)

  Read the article

• limiting connections from tomcat to IIS - proxy? iptables?

  - by Chris Phillips

  Howdy, I've webapp on tomcat6 which is connecting to an M$ PlayReady DRM instance on IIS6.0 The performance is seen to be best when we bench mark (using ab) the DRM service with 25 concurrent connections, which gives about 250 requests per second, which is ace. higher concurrent connections results in TCP/IP timeouts and other lower level mess. But there is no way to control how the tomcat app connects to the service - it's not internally managing a pool of connections etc, they are all isolated http connections to the server. Ideally I'd like a situation where we can have 25 http 1.1 connections being kept alive permanently from tomcat and requesting the licenses through this static pool of connections, which I think would the best performance. But this is not in the code, so was looking for a way to possibly simulate this at the Linux level. I was possibly thinking that iptables connlimit might be able to gracefully handle these connections, but whilst it could limit, it'd probably still annoy the app. What about a proxy? nginx (or possibly squid) seems potentially appealing to run on the tomcat server and hit on localhost as we might want to add additional DRM servers to use under load balance anyway. Could this take 100 incoming connections from tomcat, accept them all and proxy over the the IIS server in a more respectful manner? Any other angles? EDIT - looking over mod_proxy for apache, which we are already using for conventional use on an apache instance in front of this tomcat instance, might be ideal. I can set a max value on the proxy_pass to only allow 25 connections, and keep them alive permanently. Is that my answer? Many thanks, Chris

  Read the article

• Sending bulkmail from different server?

  - by Omer Gencay

  I want to send bulk domains from my vps for a domain(cagetur.com) hosted in another company. The company(cagetur) will go on using the old hosting account for its mailing operations. The vps will just be used for smtp for once a week. I created an A record "vps.cagetur.com". directed it to the IP adress of vps then created a mx record with bigger preference number "50 vps.cagetur.com." on the domain control panel. When I trace the "vps.cagetur.com" i can reach my vps now. I installed hMail on the vps. Configure it (created domain, accounts). I have no information about "system" so i couldn't get further from this point. I can connect to the mail server with Outlook without errors. I can send an email from the account on the vps but it doesn't reaches. No errors, no emails. What do i have to do for getting it work? Thank you.

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Win 2003 SBS - secure enough by default?

  - by Pekka

  I have to set up a Windows 2003 Small Business Server to work as a Subversion repository and possibly as an E-Mail server later. The machine is a virtual one, hosted with a hosting company, and freshly initialized. I used the Security Configuration Wizard to deactivate all server roles. After I install Subversion, I will open the necessary ports for the service; in addition, obviously, RDP will stay open so I can remote control the machine. Automatic updates are activated, and I will set up E-Mail notification every time somebody logs on to the server. I'm a programmer and not a professional systems administrator, so I would like to know whether you would regard this a sane and secure setup for a (publicly available) box to host sensitive code and/or E-Mail on. Is there anything in addition I should do to make the machine secure? Is there anything I can do on a long-term basis to keep the machine secure, apart from monitoring the event log (as far as I can make sense out of it), and seeing that any hotfixes are installed properly?

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• How to interrupt software raid resync?

  - by Adam5

  I want to interrupt a running resync operation on a debian squeeze software raid. (This is the regular scheduled compare resync. The raid array is still clean in such a case. Do not confuse this with a rebuild after a disk failed and was replaced.) How to stop this scheduled resync operation while it is running? Another raid array is "resync pending", because they all get checked on the same day (sunday night) one after another. I want a complete stop of this sunday night resyncing. [Edit: sudo kill -9 1010 doesn't stop it, 1010 is the PID of the md2_resync process] I would also like to know how I can control the intervals between resyncs and the remainig time till the next one. [Edit2: What I did now was to make the resync go very slow, so it does not disturb anymore: sudo sysctl -w dev.raid.speed_limit_max=1000 taken from http://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html During the night I will set it back to a high value, so the resync can terminate. This workaround is fine for most situations, nonetheless it would be interesting to know if what I asked is possible. For example it does not seem to be possible to grow an array, while it is resyncing or resyncing "pending"]

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• How can I reverse mouse movement (X & Y axis) system-wide? (Win 7 x64)

  - by Scivitri

  Short Version I'm looking for a way to reverse the X and Y mouse axis movements. The computer is running Windows 7, x64 and Logitech SetPoint 6.32. I would like a system-level, permanent fix; such as a mouse driver modification or a registry tweak. Does anyone know of a solid way of implementing this, or how to find the registry values to change this? I'll settle quite happily for how to enable the orientation feature in SetPoint 6.32 for mice as well as trackballs. Long Version People seem never to understand why I would want this, and I commonly hear "just use the mouse right-side up!" advice. Dyslexia is not something which can be cured by "just reading things right." While I appreciate the attempts to help, I'm hoping some background may help people understand. I have a user with an unusual form of dyslexia, for whom mouse movements are backward. If she wants to move her cursor left, she will move the mouse right. If she wants the cursor to move up, she'll move the mouse down. She used to hold her mouse upside-down, which makes sophisticated clicking difficult, is terrible for ergonomics, and makes multi-button mice completely useless. In olden times, mouse drivers included an orientation feature (typically a hot-air balloon you dragged upward to set the mouse movement orientation) which could be used to set the relationship between mouse movement and cursor movement. Several years ago, mouse drivers were "improved" and this feature has since been limited to trackballs. After losing the orientation feature she went back to upside-down mousing for a bit, until finding UberOptions, a tweak for Logitech SetPoint, which would enable all features for all pointing devices. This included the orientation feature. And there was much rejoicing. Now her mouse has died, and current Logitech mice require a newer version of SetPoint for which UberOptions has not been updated. We've also seen MAF-Mouse (the developer indicated the version for 64-bit Windows does not support USB mice, yet) and Sakasa (while it works, commentary on the web indicate it tends to break randomly and often. It's also just a running program, so not system-wide.). I have seen some very sophisticated registry hacks. For example, I used to use a hack which would change the codes created by the F1-F12 keys when the F-Lock key was invented and defaulted to screwing my keyboard up. I'm hoping there's a way to flip X and Y in the registry; or some other, similar, system-level tweak out there. Another solution could be re-enabling the orientation feature for mice, as well as trackballs. It's very frustrating that input device drivers include the functionality we desperately need for an accessibilty concern, but it's been disabled in the name of making the drivers more idiot-proof.

  Read the article

• Auto Log-Off Windows users - Windows 2003 domain

  - by thehatter

  Hi! I am trying to make windows clients automatically log off after some time, I have been trying to use the winexit.scr which I have seen working else where in a similar environment. After working though these instructions (I did read the comments and notice the original ADM provided is buggy) I've had no joy what so ever! Winexit.scr refuses to read any settings in the registry, even while using a test account I can access the required reg key(s); edit, add, and remove values. Essentially winexit.scr always uses it's default values: 30 second timeout, no forced log-out. What I really want is a 30 minute timeout with a forced log-out, closing all the users apps etc. I've tried removing and re-adding the ADM template, creating the GPO from scratch several times, giving various registry permissions - including full control to "Everybody" just for fun! Oh, clients are all win XP SP3, DC is win 2003 R2 SP2. So, can anybody suggest something? Cheers!

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• switchover in postgresql

  - by user1010280

  I am using Postgresql 9.0 with Streaming replication. So, during switchover I follow these steps:- Get the server timestamp on primary. Get the current log position on primary. Set Verify Log location Verify Transaction Received Location Shutdown DB on production. Synchronize the transaction logs from PR to DR. Trigger a failover on the DR Database by creating the trigger file specified in recovery.conf Verify DB Mode on DR Copy the control file from from DR to primary. copy the temporary stats file from DR to primary. copy the history file from DR to primary. Create recovery.conf file. Start Database in standby mode in primary. Verify DB mode on PR At step (6), I have to copy last wal generated on Primary to standby and sync both PR and standby. but this thing takes time to copy files because this remote. So that postgres will keep seraching for wal for long time and after that it stops the server. So I want to know is there any way so that I can ask postgres to stop seraching or locating WAL after shutdown??? because postgres tries to locate this wal every 5 seconds. Please reply as soon as possible..its urgent...

  Read the article

• How to create NTFS partition in Linux to install Windows 7 from USB?

  - by Michal Stefanow

  I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

  Read the article

• Is there any way to synchronize Outlook RSS Feeds with BlackBerry?

  - by nvuono

  Does anyone know how I can view the contents of my Outlook 2007 RSS Feeds from a corporate-issued BlackBerry? Our Inbox and Calendar are already integrated with corporate exchange servers but it looks like nobody cares too much about the RSS Feeds. Is there some setting on my Blackberry or in Outlook I could possibly tweak to include these updates? I know there are many standalone RSS readers available for blackberry (Google Reader for example) but I mention Outlook RSS Feeds specifically in my question because I am subscribing to a number of RSS feeds I've setup on my intranet for various version control systems that would be inaccessible to an external RSS reader. It seems like I might have to setup some sort of email commit notifications if I want anything from my blackberry but I much prefer the 'pull' method of an RSS feed viewer over receiving streams of emails. Please feel free to suggest any alternatives! Edit: I've additionally tried moving my "SVN Repository" folder directly into my Mailbox instead of keeping it as a child of the RSS Feeds folder. This allows me to view the SVN Repository folder on my blackberry where previously the RSS Feeds folder and all children were hidden but unfortunately it never seems to get populated with the items that are displaying in Outlook. I've even made a fresh commit to make sure that the SVN Repository folder still works correctly in Outlook from outside the RSS Feeds folder but no luck on the BlackBerry end of things. BlackBerry Model Details: BlackBerry 8310 smartphone (EDGE) v4.2.2.170 Platform 2.5.0.30

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Windows ACL inheritance issues for FTP server and automated tools

  - by Martin Sall

  I have set up Cerberus FTP server. By default, Cerberus FTP service runs under SYSTEM ACCOUNT. Also I have some console applications which run as scheduled tasks. They are running under a dedicated "Utilities" user account which has "Log on as batch job" permissions. These console applications take uploaded FTP files, process them and then move them to some dedicated archive folder. The problem is that my console apps are throwing Security exceptions when trying to acces the uploaded files. I tried to give the Full control permissions on the ftproot folder for my "Utilities" account and I have checked that "Replace all Child object permissions with inheritable permissions from this object" checkbox, but it affects only current files. When new files are uploaded, they again are not accessible by my "Utilities" account. I tried to go another way and put Cerberus FTP service under "Utilities" account. Then I also needed to give "Utilities" account permissions on Cerberus Data folder in ProgramData. Still no luck - after this operation, Cerberus internal SOAP web service stopped working (although everything else seems to work). I need that SOAP service to be available, so running the Cerberus FTP under "Utilities" account seems to be not an option. Unless I find out, what else do I need to set up for that "Utilities" account to stop Cerberus from complaining. I guess, Cerberus is uploading files to some temporary folder and so those files get the permissions form that folder and keep the same permissions even after moved to the ftproot. What would be the right solution for this which would grant Cerberus FTP server and the "Utilities" account minimal needed permissions to access the contents of the ftproot folder?

  Read the article

• How to correctly configure DNS for Icelandic domains and Plesk

  - by Leonard Challis

  I have a domain registered with ISNIC (domain.is). They only let you set nameservers that pass their requirements. I've been told it's this requirement that I need to fix: Nameserver must be consistently registered in DNS, i.e. its own A resource record must be available and a corresponding PTR resource record as well. I allocated two new IP addresses from my server host and at that point set their PTR records to ns0.domain.is and ns1.domain.is. After that I created two A records for that domain in Plesk, again ns0. and ns2.domain.is with their respective IPs. Next, I went to the ISNIC page to register my nameservers, along with their IP addresses I'd allocated and this worked perfectly for both without error. So the final job was to set the nameservers for the domain via ISNIC's control panel, however when I try, I'm getting this error: Test results for "NS0.DOMAIN.IS": The nameserver ns1.vps123.vpsprovider.com is not consistently registered in DNS (ns1.vps123.vpsprovider.com => 1123.123.123.123 => vps123.vpsprovider.com) The nameserver ns0.vps123.vpsprovider.com is not consistently registered in DNS (ns0.vps123.vpsprovider.com => 1123.123.123.123 => vps123.vpsprovider.com) The nameserver ns0.DOMAIN.IS is missing from the NS record set for DOMAIN.IS Test results for "NS1.DOMAIN.IS": The nameserver ns1.DOMAIN.IS is missing from the NS record set for DOMAIN.IS The nameserver ns0.DOMAIN.IS is missing from the NS record set for DOMAIN.IS This is really at the limits of my DNS knowledge I'm afraid. It feels like I'm close but maybe missing a vital part, linking the nameservers in Plesk or something?

  Read the article

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• A lots of Apache processes are using my CPU uses always more than 70%

  - by Barkat Ullah

  I am running a plesk panel in 1and1. I have 120 sites running and all are using pligg cms, each site has 600 visitors per day. Please see the details of my server below: HDD-1000GB RAM-16GB Processor-6 Core I always see a lot of apache processes running in my # top view, so the server seems overloaded. If I can reduce the amount apache processes I think the server will be ok. But I don't know why too many apache processes are running. Please see the link below for the screenshot of my # top view: http://dl.dropbox.com/u/26967109/%23Top-2.jpg Sometimes I saw too many connection error in my plesk control panel, so I added the below line in my [mysqld] section: set-variable=max_connections=416 But I didn't find a solution yet. I have also added maxclients and serverlimit 416 in the config /etc/httpd/conf/httpd.conf But no solution yet. I am researching around more than 7 days but don't get any solution. Please help me to solve the problem. In peak hours my sites are taking too much time to load, but off-peak hour it is ok. Please help me to find out the actual problem.

  Read the article

< Previous Page | 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022  | Next Page >