Search Results

Search found 22532 results on 902 pages for 'computer hardware'.

Page 102/902 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

• Is ASUS P5K-V Comptatable with this Crucial M4 SSD?

  - by Owen Melbourne

  hope alls well, Upgrading my old pc which has an Asus P5K V Motherboard, and im looking to add an SSD to it. I've come across Crucials website which says these 2 products are available http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=49C6AB1FA5CA7304 which is this http://www.ebuyer.com/product/266526 hard drive I believe. Could somebody confirm that these should be compatable? Many thanks

  Read the article

• What is this Cable for? 4 Pin to 2 Pin from Riser to Perc in Dell R410

  - by Kyle Brandt

  I got a new raid card for a R410 server since the S300 that came with it doesn't support raid with Linux (No work around for this if SAS from what I could find). Anyways, the RAID card has 2 pins on it and there is a cable that that connects to a 4 pin connection on the riser. The cable only has two wires, one black and one red. What is this cable for? My guess would be maybe LED status for the front panel or something like that, but I am just guessing....

  Read the article

• External USB disk drive cannot be remounted in Windows XP

  - by jackhab

  I have Maxtor Basics Desktop 1TB external USB drive connected to Windows XP. The dirve's firmware puts it to sleep after 10-20 min of inactivity and then the drive cannot be mounted unless I reset it via power connector. While in sleep mode I can see the device in the Device Manager under both Disk drives and USB sections. Is there a way to get the drive out of sleep mode without hard reset? Thanks

  Read the article

• Is this a normal operating temperature range for a New Third-Generation MacBook Air (2.13 MHz, 120 G

  - by doug

  Even with just my text editor open (no web browser) and maybe the terminal, the baseline temperature is usually above 40 C. When i open 4-5 browser tabs in Safari (even if none of Sites have Flash) the temp can quickly go over 50 C. (In addition, i am observing these temps even though i have turned the fan up to 3000 rpms). (i have install smcFanControl on my MBA so i can see the temp in the menu bar.) So this means my MBA is running much warmer than my MBP; and in practice, it means that i have to be very careful how i use my MBA. Of course if i load a Site with Flash, it just freaks out, and often quickly goes above 65 C (I've installed a flash blocker to avoid this). Is anyone else observing this behavior? I have checked the Apple boards and sure enough, there are a lot of complaints, but nothing from Apple.

  Read the article

• Testing Firewire 800 port on MacBook Pro

  - by dtlussier

  I am having trouble getting my MacBook pro to mount an external Firewire hard drive. I am able to mount the disk no problem on other Macs, just not my machine. I haven't received any errors from my machine, and don't see anything related to the Firewire port in the logs. Are there good diagnostic tools for this type of problem that come with the Mac? other free alternatives ?

  Read the article

• What is causing my newly built PC to BSOD?

  - by Ben S

  I recently built my own PC from parts and installed Windows 7 and I have been getting BSODs with various different stop codes. The latest was 0x24, but I've also had 0xd1 and 0x1e. However, Windows does not let me know where the fault occurred, so I have no idea how to go about resolving this. I've uploaded the last three minidumps in case someone can make sense out of them and let me know what could be causing my BSODs. Thanks, Ben

  Read the article

• Recommendations for a JetDirect print server for USB 2.0 printers?

  - by eleven81

  I have been using some older HP JetDirect 300x print servers for a variety of parallel printers over the years. These things work great for every printer I have tried them with, including HP's, Dell's, and even a Mountbatten braille embosser! These have been a boon for printers whose internal network cards fail, but whose parallel ports continue working. I don't have to throw away the $500 printer that is one year and a week old, and can keep using it for many, many years. Now that very few printers are coming with parallel ports, but are coming solely with USB connections and network cards. When the network card fails but the printer is still usable, I want to continue using it on the network with a JetDirect card. In summary: Does anyone have any recommendations for JetDirect cards that will work as well with USB 2.0 printers of unspecified manufacturer that my old JetDirect 300x cards do?

  Read the article

• Can enabling a RAID controller's writeback cache harm overall performance?

  - by Nathan O'Sullivan

  I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

  Read the article

• Hiding monitor from windows, working with it from my app only [closed]

  - by Mikhail

  I need to use a monitor as a "private" device for my special application, I want to use it as a flashlight of a sort and draw special patterns on it in full screen. I don't want this monitor to be recognized by OS (Windows 7) as a monitor. I.e. user should not be able to move mouse to that monitor, or change its resolution, or run screensaver on it or whatever. But I want to be able to interact with it from my application. Monitor is plugged using an HDMI cable to a video card (most probably nVidia). What is the simplest way to do this? All solutions are appreciated, including purchasing additional adapters or simple video cards, or any other special devices.

  Read the article

• How can I get Windows 7 to work with two Nvidia graphics cards with different drivers?

  - by Max

  This is similar to this question, but I am using more similar cards with Windows 7. I just purchased a Zotac Nvidia GeForce 7200 GS. I have a motherboard with two PCI Express x16 slots. There is already an MSI Nvidia GeForce 8800 GTS being used as the primary card, driving two LCD monitors. I would like the Zotac to output to a TV via DVI-out. Unfortunately, when Windows detects the Zotac and installs its drivers, or I manually install them, Windows stops being able to boot up. If I remove them and re-install the MSI 8800 drivers, I can boot again, but Windows can no longer see the Zotac 7200--it shows up as a yellow triangle in Device Manager. I've read conflicting reports about this. Some people claim that Windows 7 will support multiple heterogeneous graphics card drivers, as long as they are all using the same driver API ("WDDM?"). Others say that they have to be using the exact same driver, or it won't work. Others claim that you have to use the exact same card. which is it, exactly? I know I can run the MSI 8800 in SLI if I purchase another, but I don't need that kind of power--I just need HD-out to my television. I read somewhere that running two cards in SLI precludes you from using 100% of their output ports, so I'm not sure if that's an option. I suppose I could also run two MSI 8800's without SLI, but again, that's more power than I need (and more money than I'd like to spend). Also, I don't think this exact model is even manufactured anymore. Any ideas?

  Read the article

• Small (Micro) 16GB USB flash drive

  - by cust0s

  I'm looking for a small 16GB USB flash drive, that's good looking, will stand the test of time and can be attached to a key ring. I don't want extra software (like that found on the SanDisk Micro Cruzer) and it needs to be compatible with Windows, Mac and Linux. Also, I'd rather pay a bit more than buying a cheap flash drive and then it crapping out on me.

  Read the article

• ImgBurn CD/DVD burn error

  - by bobby

  I am getting the above error when I try to burn a CD/DVD on my DVD writer. I am seeing this error for every CD/DVD I try to burn. I am not able to write any CDs or DVDs using ImgBurn. What could be causing this error?

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• What is the name of this screw? (from HP ProLiant quick-deploy rail kits)

  - by kockiren

  I need the name of the screw for the HP quick deploy rail kit. The screw clicks into the square holes of the rack. It is a Gen4 Rail kit but the screw is like the Gen8 Rail kit ones. I called HP support, but they couldn't really help me. Unfortunately the rack manual does not name this screw either. After googling a while, I found the compatible "Thumb Style Rack Screws". It would do the job but isn't exactly what I am looking for. So, what is the name of the pictured screw.

  Read the article

• Instructions per cycle?

  - by Matt Simmons

  I've been learning a little bit more about how processors work, but I haven't been able to find a straight answer about instructions per cycle. For instance, I was under the impression that a four core CPU could execute four instructions per cycle, so a four core CPU running at 2Ghz would execute 8 billion operations per second. Is this the case? I'm sure it's oversimplifying things, but if there's a guide or something else I can use to set myself straight, I'm definitely open to ideas.

  Read the article

• Is it safe to leave a broadband router running 24/7?

  - by Anirvan

  My father-in-law's ISP warned him in the strictest possible terms to physically turn off his rented Nokia Siemens C2110 PPPoE broadband router when not in use. Everyone I know leaves their broadband router on all the time, and I've never heard of any negative impacts. Is leaving a consumer broadband router running 24/7 really problematic? Is the ISP in question being ridiculously paranoid?

  Read the article

• HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

  - by JohnRB

  I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

  Read the article

• How do I re-enable the IPMI temperature sensors?

  - by NobleUplift

  I've never had a problem reading temperature sensors with ipmitool on my server, but recently the temperature readings started showing up as disabled: # ipmitool sdr list Temp | disabled | ns Temp | disabled | ns Ambient Temp | 21 degrees C | ok CMOS Battery | 0x00 | ok VCORE | 0x00 | ok VDDIO | 0x00 | ok VDDA | 0x00 | ok VTT | 0x00 | ok VCORE | 0x00 | ok VDDIO | 0x00 | ok VDDA | 0x00 | ok VTT | 0x00 | ok VDD 1.2V PG | 0x00 | ok Linear PG | 0x00 | ok I am using OpenIPMI 2.0.19 and ipmitool 1.8.12. How can I re-enable my temperature sensors?

  Read the article

• Best motherboard power supply combo for backblaze server

  - by jin14

  Building a backblaze server as described in this article. http://blog.backblaze.com/ So 45 hard drives in one box. I'm making it a MSDPM 2010 server so I actually don't even need raid cards in there as MSDPM will figure out how to use all of the hard drives on it's own. So need to know what motherboard, CPU, power supply I should get. Primary hard drive : SSD 128GB Storage : 45 1.5GB sata drives OS : windows 2008 Backup software : Microsoft System center Data protection server 2010 Need to know Which mother board to buy which will support 45 SATA hard drives. Don't need a raid card. Which power supply can power all 45 hard drives, 1 ssd drive, motherboard. Best set of equipment that meets my needs wins

  Read the article

• Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

  - by ame

  Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from block of hard drives to controller, but I haven't any indication of hard discs on server front panel. There's indication of activity of drives only during boot of server. Controller has 2-pin connector (JT6B3, SAS Activity LED header) but where and how can I connect it? Thanx.

  Read the article

• What precautions should I take once defective RAM has been replaced?

  - by DustByte

  I recently discovered that my RAM is faulty (MemTest86+). I am waiting for new RAM to be sent to me.  It was through sheer luck that I discovered something was wrong. I was copying a large amount of big files and decided to verify the copies by their checksums. I discovered strange discrepancies, and noticed that checksum computation for the same file was not consistent. Now, this is the only problem I have encountered; no BSOD, no crashes, no errors. In a sense this makes me more worried than if I would have had massive crashes. I have no idea for how long the RAM has been faulty, and I have no idea if corrupt bits have been saved into files on my hard drives. I do know the RAM was fine two months ago (tested it back then). I am a user of Adobe's Lightroom and I am worried that photos or the catalog itself could carry corrupt data. Question: what should I do once new healthy RAM has been installed? Reinstall Windows (I'm using Windows 7, 64 bit)? Is there a risk that I will be presented with nasty surprises in the future if I don't? What about personal files? I have backups of some of the files but for newer files I'm not sure I can even trust the backups. It's going to take me many hard hours to manually replace files with older versions, or compare checksums.

  Read the article

• Restarting an IBM BMC without restarting the server itself

  - by SRobertJames

  I have a few servers with IBM BMC (Baseboard Management Controller). I'd like to power cycle the BMC without restarting the server. Is this possible? How? Note: On one of them, the web interface is down; so I'd need to either do this by physically restarting the BMC (not sure how to do this - even the power button on the server isn't supposed to recycle the BMC, I believe) or via the UDP or SNMP interface (again, not sure how to do that either)

  Read the article

• How does the build quality of laptops compare?

  - by pgwillia

  I'm looking to replace my 5 year old laptop. I want my next laptop to endure at least this long. I typically have Thunderbird, Firefox, Eclipse Java IDE, Skype, a ssh session, and Apache Tomcat running. I'm currently running Karmic Ubuntu, but am agnostic about operating system and would move to Win 7 or OS X. I frequently travel with this computer. I also value battery longevity and power conservation (if possible). Above all I'm looking to minimize cost. I think the hardware that best meets my needs is an Intel i7 processor, 8 GB RAM, 100GB @7200 rpm or SSD hardrive, and about 15 inch monitor. These specs are met by most brands. Does anyone know specific pros/cons and build quality for Macbook Pro, Lenovo Thinkpad (W510 or T510), Sony's VPC-F1190, and ASUS G Series G73JH-X1 NoteBook? Are all i7 processors created equal? Do you have other suggestion that meet my needs?

  Read the article

• Determine Server specs for a Rails with MySQL database (on AWS)

  - by Rogier

  I developed a intranet applications with Rails (3.2) for one of my customers. There will be around 30-40 employees working with it. Backend is MySQL (5). What would be the best way to determine the servers specs needed? Given: max. load will be roughly 2400 (40*60) HTTP requests (mixed GET / POST) per hour. 15% of these calls are JSON calls (iOS) avg request will make between 5-10 database calls 500-800 SQL INSERTS per day webpages are fairly simple (no images, just text) avg webpage is 15 request (css/js/etc) and total size is 35-45 KB More specific, since they need access from multiple geographical locations, we are thinking of running a bitnami Ruby stack in the AWS cloud (uptime is important). Any thoughts on a AWS Instance (small/medium) and Utilization (light/medium/heavy) ? Thanks!

  Read the article

• Laptop turns off after 20 minutes of use

  - by Christoph

  My laptop a sony vaio VGN-NW11S http://www.trustedreviews.com/Sony-VAIO-VGN-NW11S-S---15-5in-Laptop_Laptop_review. Everytime i turn it on, in safe mode or not, if i try to open an application i.e. run a process such as google chrome or event viewer, defrag, virus scan, it completely turns off without warning, nor giving a trace of events the next time I switch it on. Apart from that, I had worries it might be my battery or power supply but I dont think it is that, I took the laptop apart cleaning fans etc. and have ordered some cpu paste as I checked to see the condition of the processor. I will post to see if re-applying the paste works. One more thing, when the heavy processes kick in, the fan starts to make a lot of noise, maybe trying to cool down the CPU? Any ideas on what else it could be and what I could do to test what is wrong?

  Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >