Search Results

Search found 23567 results on 943 pages for 'max link'.

Page 103/943 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  Hi, When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

• Why are cookies unrecognized when a link is clicked from an external source (i.e. Excel, Word, etc..

  - by Nick

  I noticed that when a link is clicked externally from the web browser, such as from Excel or Word, that my session cookie is initially unrecognized, even if the link opens up in a new tab of the same browser window. The browser ends up recognizing its cookie eventually, but I am puzzled as to why that initial link from Excel or Word doesn't work. To make it even more challenging, clicking a link works fine from Outlook. Does anybody know why this might be happening? I'm using the Zend Framework with PHP 5.3.

  Read the article

• BI&EPM in Focus Sep 2012

  - by Mike.Hallett(at)Oracle-BI&EPM

  Customers ·       Iluka Resources Improves Business Insight into Mining Operations Through Significantly Faster, Customized Analyses ·       Waikato Regional Council Consolidates Financial Reports up to 10 Times Faster  ·       Lojas Renner Shortens Budget Consolidation from Three Days to 15 Minutes; Improves Data Quality, and Supports Aggressive Expansion Plans  ·       Link to Complete Archive ·       Profit Magazine article featuring General Dynamics: RECONnomics: Integrate. Innovate. Grow (link) ·       Video: Goodhope Asia Unifies Financial Data with Oracle Hyperion (link)   Enterprise Performance Management ·       Oracle University Training on Demand: 1.     Oracle Hyperion Financial Reporting 11.1.2 for Financial Management (link) 2.     Oracle Essbase Bootcamp: On Demand (link) 3.     Oracle Hyperion Planning 11.1.2: Create & Manage Applications On Demand (link)   Business Intelligence ·       Oracle University Training on Demand: 1.     Learn How to Create Analyses, Dashboards with OBI 11g (link) 2.     Build Repositories with Oracle Business Intelligence 11g (link) 3.     Oracle BI Publisher 11g Fundamentals (link) 4.     Oracle BI Applications Courses now available for 7.9.6  (link) 5.     Oracle BI 11g: New Features and Exalytics ·       Oracle Business Intelligence Release 11.1.1.6.2BP, updated information: 1.     Oracle BI Mobile at the Speed of Thought 2.     What's New in Oracle Business Intelligence Mobile 3.     What's New in Oracle Business Intelligence Visualizations 4.     Oracle Business Intelligence on Oracle.com 5.     Download the New Release ·       Discover How to Turn Data into Insight: Big Data Guide : Whitepaper and set of short Videos. ·       New OPN Specialisation Exam for OBI 11g Certification . ·       Lastest BIC2g and Exalytics Demonstration VMs for Partners . ·       New Version 2.3 Oracle Endeca Information Discovery and Server now available . ·       New Oracle BI Publisher 11.1.1.6 Trial Edition Now Available .

  Read the article

• CentOS Client - Unable to Establish iSCSI connection with multiple interfaces on the initiator

  - by slashdot

  So after upgrading to CentOS 6.2, I am seemingly no longer able to login into my iSCSI targets. I have multiple interfaces on different subnets on the system, and I first thought that it had to do with the fact that I may not be binding correct interfaces, which seems to be the case when looking at netstat, as this is clearly wrong: [root]? netstat -na|grep .90 tcp 0 1 10.10.100.60:42354 10.10.8.90:3260 SYN_SENT tcp 0 1 10.10.100.60:40777 10.10.9.90:3260 SYN_SENT I then went ahead and disabled all but one interface, and so as a result netstat appears to be correct, but the issue with login remains. I am positive that the target never sees a packet, because I see nothing by SYN_SENT. I know the problem is on my client, because the target is servicing multiple systems, none of which are CentOS 6.2. At this point I am pretty confident that some things changed between CentOS 6.0/6.1 and 6.2. So, if anyone have any thoughts, or ran into this, I would very much like to hear your thoughts. [root]? iscsiadm --mode node --targetname iqn.2011-12.dom.homer:01:lab-centos-servers-00001 --portal 10.10.8.90:3260,2 --interface=sw-iscsi-0 --login Logging in to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260] (multiple) iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals [root]? netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.10.8.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2.7 10.10.9.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3.7 10.10.100.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2.7 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3.7 0.0.0.0 10.10.100.1 0.0.0.0 UG 0 0 0 eth0 Output of ip addr show for the two interfaces involved: [root]? for i in 2.7 3.7; do ip addr show eth$i; done 6: eth2.7@eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:8d brd ff:ff:ff:ff:ff:ff inet 10.10.8.60/24 brd 10.10.8.255 scope global eth2.7 inet6 fe80::20c:29ff:fe94:5b8d/64 scope link valid_lft forever preferred_lft forever 7: eth3.7@eth3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:97 brd ff:ff:ff:ff:ff:ff inet 10.10.9.60/24 brd 10.10.9.255 scope global eth3.7 inet6 fe80::20c:29ff:fe94:5b97/64 scope link valid_lft forever preferred_lft forever Update 01/06/2012: This issue is getting even more interesting by the day it seems. I went a few weeks back and grabbed a snapshot of this system from before upgrading to 6.2. I spun up a new system from the snapshot, and reconfigured interface info and host keys, as well as iSCSI initiator and iscsi interface info to match new MACs. Changed nothing else. Then, I attempted to connect to my targets, and no issues at all. I cannot say that this was unexpected. I then went ahead and compared sysctl settings from both systems and there were differences after the upgrade, but nothing seemingly relevant to iSCSI or IP that could contribute to this. I also noticed that by default now two sessions per connection were enabled after the upgrade, but I changed it back to 1 session in /etc/iscsi/iscsid.conf. On the problematic system we can see that source interface is seemingly wrong, but even when I disable the 10.10.100 interface, problems persist. So, while this may be relevant, I could not validate it for certain. Needless to say, further research is necessary. Something is clearly different between releases. Working system is on 6.1, and non-working is 6.2. ::Working System:: tcp 0 0 10.10.8.210:39566 10.10.8.90:3260 ESTABLISHED tcp 0 0 10.10.9.210:46518 10.10.9.90:3260 ESTABLISHED [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.210 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.210 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.210 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 ::Non-working System:: tcp 0 1 10.10.100.60:44737 10.10.9.90:3260 SYN_SENT tcp 0 1 10.10.100.60:55479 10.10.8.90:3260 SYN_SENT [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.60 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.60 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.60 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 And the result is still same: [root]? iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not login to [iface: sw-iscsi-1, target: iqn.2011-12.dom.homer:02:lab-centos-servers-00001, portal: 10.10.9.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals Update 01/08/2012: I believe I have been able to figure out the answer to my issue. It is quite obscure and I doubt this will happen to anyone else any time soon. It turns out that setting iface.iscsi_ifacename and iface.hwaddress in the interfaces configuration file is not legal. When one manually adds an iscsi target, such as below, all settings from the interface config file are copied into the node config file, that gets created by the below command. Result is parameters iface.iscsi_ifacename and iface.hwaddress together in the same config file. These parameters are seemingly mutually exclusive, which does not exactly make sense, or there is perhaps an oversight in the codepath. Perhaps I will investigate further. # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:01:lab-centos-servers-00001 -p 10.10.8.90,3260,2 -I sw-iscsi-0 # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:02:lab-centos-servers-00001 -p 10.10.9.90,3260,2 -I sw-iscsi-1 Notice, below I commented out iface.hwaddress and iface.ipaddress, after which I re-added targets, with same command as above. All works just fine. [root]? cat * # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-0 iface.net_ifacename = eth2.6 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.8.60 iface.transport_name = tcp iface.vlan_id = 6 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-1 iface.net_ifacename = eth3.7 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.9.60 iface.transport_name = tcp iface.vlan_id = 7 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD Again, chances of this happening to someone else are slim to none, so likely waste of time typing this up. But, if someone does encounter this issue, I hope this post will help.

  Read the article

• How to specify this 'symbolic link' for the Jungo WinDriver?

  - by user252098

  Just now , I try to install the Jungo WinDriver in the Ubuntu 13.10 . But I am puzzled by the its manual : 4.2.3. Linux WinDriver Installation Instructions 4.2.3.1. Preparing the System for Installation In Linux, kernel modules must be compiled with the same header files that the kernel itself was compiled with. Since WinDriver installs kernel modules, it must compile with the header files of the Linux kernel during the installation process. Therefore, before you install WinDriver for Linux, verify that the Linux source code and the file version.h are installed on your machine: Install the Linux kernel source code: If you have yet to install Linux, install it, including the kernel source code, by following the instructions for your Linux distribution. If Linux is already installed on your machine, check whether the Linux source code was installed. You can do this by looking for 'linux' in the /usr/src directory. If the source code is not installed, either install it, or reinstall Linux with the source code, by following the instructions for your Linux distribution. Install version.h: The file version.h is created when you first compile the Linux kernel source code. Some distributions provide a compiled kernel without the file version.h. Look under /usr/src/linux/include/linux to see whether you have this file. If you do not, follow these steps: Become super user: $ su Change directory to the Linux source directory: cd /usr/src/linux Type: make xconfig Save the configuration by choosing Save and Exit. Type: make dep Exit super user mode: exit To run GUI WinDriver applications (e.g., DriverWizard [5]; Debug Monitor [7.2]) you must also have version 5.0 of the libstdc++ library — libstdc++.so.5. If you do not have this file, install it from the relevant RPM in your Linux distribution (e.g., compat-libstdc++). Before proceeding with the installation, you must also make sure that you have a linux symbolic link. If you do not, create one by typing /usr/src$ ln -s 'target kernel'/linux For example, for the Linux 2.4 kernel type /usr/src$ ln -s linux-2.4/ linux ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ I can't understand how to specify these two parameters in my Ubuntu .

  Read the article

• postfix: Temporary lookup failure

  - by mk_89

  I have followed the tutorials step by step for installing and configuring postfix https://help.ubuntu.com/community/Postfix https://help.ubuntu.com/community/PostfixBasicSetupHowto I am trying to test the services to whether Temporary lookup failure error telnet localhost 25 250 2.1.0 Ok rcpt to: fmaster@localhost 451 4.3.0 <fmaster@localhost>: Temporary lookup failure rcpt to: info@localhost 451 4.3.0 <info@localhost>: Temporary lookup failure I have tried searching the web but I have found no solutions, why am I getting this problem? mail.log Sep 24 01:03:05 bookcdb postfix/smtpd[21055]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <info@localhost>: Temporary lookup failure; from=<root@localhost> to=<info@localhost> proto=ESMTP helo=<localhost> Sep 24 01:03:19 bookcdb postfix/smtpd[21055]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <root@localhost>: Temporary lookup failure; from=<root@localhost> to=<root@localhost> proto=ESMTP helo=<localhost> Sep 24 01:08:19 bookcdb postfix/smtpd[21055]: timeout after RCPT from unknown[::1] Sep 24 01:08:19 bookcdb postfix/smtpd[21055]: disconnect from unknown[::1] Sep 24 01:10:49 bookcdb postfix/anvil[21059]: statistics: max connection rate 1/60s for (smtp:::1) at Sep 24 01:00:49 Sep 24 01:10:49 bookcdb postfix/anvil[21059]: statistics: max connection count 1 for (smtp:::1) at Sep 24 01:00:49 Sep 24 01:10:49 bookcdb postfix/anvil[21059]: statistics: max cache size 1 at Sep 24 01:00:49 Sep 24 01:15:36 bookcdb postfix/smtpd[22175]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Sep 24 01:15:36 bookcdb postfix/smtpd[22175]: warning: hostname localhost does not resolve to address ::1: No address associated with hostname Sep 24 01:15:36 bookcdb postfix/smtpd[22175]: connect from unknown[::1] Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: error: open database /etc/postfix/transport.db: No such file or directory Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport lookup error for "root@localhost" Sep 24 01:15:55 bookcdb postfix/trivial-rewrite[22195]: warning: transport_maps lookup failure Sep 24 01:15:59 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:15:59 bookcdb postfix/trivial-rewrite[22195]: warning: hash:/etc/postfix/transport lookup error for "fmaster@localhost" Sep 24 01:15:59 bookcdb postfix/trivial-rewrite[22195]: warning: transport_maps lookup failure Sep 24 01:15:59 bookcdb postfix/smtpd[22175]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <fmaster@localhost>: Temporary lookup failure; from=<root@localhost> to=<fmaster@localhost> proto=ESMTP helo=<localhost> Sep 24 01:16:30 postfix/smtpd[22175]: last message repeated 5 times Sep 24 01:16:30 bookcdb postfix/smtpd[22175]: disconnect from unknown[::1] Sep 24 01:19:50 bookcdb postfix/anvil[22177]: statistics: max connection rate 1/60s for (smtp:::1) at Sep 24 01:15:36 Sep 24 01:19:50 bookcdb postfix/anvil[22177]: statistics: max connection count 1 for (smtp:::1) at Sep 24 01:15:36 Sep 24 01:19:50 bookcdb postfix/anvil[22177]: statistics: max cache size 1 at Sep 24 01:15:36 Sep 24 01:20:32 bookcdb postfix/qmgr[21039]: D0C596E0B34: from=<[email protected]>, size=442, nrcpt=1 (queue active) Sep 24 01:20:32 bookcdb postfix/qmgr[21039]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 01:20:32 bookcdb postfix/error[22402]: D0C596E0B34: to=<[email protected]>, relay=none, delay=5369, delays=5369/0.01/0/0.09, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 01:24:16 bookcdb postfix/smtpd[22573]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Sep 24 01:24:16 bookcdb postfix/smtpd[22573]: warning: hostname localhost does not resolve to address ::1: No address associated with hostname Sep 24 01:24:16 bookcdb postfix/smtpd[22573]: connect from unknown[::1] Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: error: open database /etc/postfix/transport.db: No such file or directory Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "root@localhost" Sep 24 01:24:43 bookcdb postfix/trivial-rewrite[22594]: warning: transport_maps lookup failure Sep 24 01:25:14 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:25:14 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "[email protected]" Sep 24 01:25:14 bookcdb postfix/trivial-rewrite[22594]: warning: transport_maps lookup failure Sep 24 01:25:14 bookcdb postfix/smtpd[22573]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<root@localhost> to=<[email protected]> proto=ESMTP helo=<localhost> Sep 24 01:25:32 bookcdb postfix/qmgr[21039]: 2E5C36E0A07: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 01:25:32 bookcdb postfix/qmgr[21039]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 01:25:32 bookcdb postfix/qmgr[21039]: 0EA3A6E0ACC: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 01:25:32 bookcdb postfix/error[22631]: 2E5C36E0A07: to=<[email protected]>, orig_to=<root>, relay=none, delay=30203, delays=30203/0.01/0/0.1, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 01:25:32 bookcdb postfix/error[22632]: 0EA3A6E0ACC: to=<[email protected]>, orig_to=<root>, relay=none, delay=30115, delays=30115/0.01/0/0.11, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 01:25:58 bookcdb postfix/smtpd[22573]: warning: non-SMTP command from unknown[::1]: subject: fdf Sep 24 01:25:58 bookcdb postfix/smtpd[22573]: disconnect from unknown[::1] Sep 24 01:26:01 bookcdb postfix/smtpd[22573]: warning: hostname localhost does not resolve to address ::1: No address associated with hostname Sep 24 01:26:01 bookcdb postfix/smtpd[22573]: connect from unknown[::1] Sep 24 01:26:10 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:26:10 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "root@locahost" Sep 24 01:26:10 bookcdb postfix/trivial-rewrite[22594]: warning: transport_maps lookup failure Sep 24 01:26:37 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:26:37 bookcdb postfix/trivial-rewrite[22594]: warning: hash:/etc/postfix/transport lookup error for "fmaster@localhost" Sep 24 01:26:37 bookcdb postfix/trivial-rewrite[22594]: warning: transport_maps lookup failure Sep 24 01:26:37 bookcdb postfix/smtpd[22573]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <fmaster@localhost>: Temporary lookup failure; from=<root@locahost> to=<fmaster@localhost> proto=SMTP Sep 24 01:26:45 bookcdb postfix/smtpd[22573]: disconnect from unknown[::1] Sep 24 01:30:05 bookcdb postfix/anvil[22575]: statistics: max connection rate 1/60s for (smtp:::1) at Sep 24 01:24:16 Sep 24 01:30:05 bookcdb postfix/anvil[22575]: statistics: max connection count 1 for (smtp:::1) at Sep 24 01:24:16 Sep 24 01:30:05 bookcdb postfix/anvil[22575]: statistics: max cache size 1 at Sep 24 01:24:16 Sep 24 01:34:57 bookcdb dovecot: master: Dovecot v2.0.19 starting up (core dumps disabled) Sep 24 01:35:02 bookcdb amavis[1009]: starting. /usr/sbin/amavisd-new at mail.bookcdb.com amavisd-new-2.6.5 (20110407), Unicode aware Sep 24 01:35:02 bookcdb amavis[1009]: Perl version 5.014002 Sep 24 01:35:05 bookcdb amavis[1155]: Net::Server: Group Not Defined. Defaulting to EGID '114 114' Sep 24 01:35:05 bookcdb amavis[1155]: Net::Server: User Not Defined. Defaulting to EUID '108' Sep 24 01:35:05 bookcdb amavis[1155]: Module Amavis::Conf 2.208 Sep 24 01:35:05 bookcdb amavis[1155]: Module Archive::Zip 1.30 Sep 24 01:35:05 bookcdb amavis[1155]: Module BerkeleyDB 0.49 Sep 24 01:35:05 bookcdb amavis[1155]: Module Compress::Zlib 2.033 Sep 24 01:35:05 bookcdb amavis[1155]: Module Convert::TNEF 0.17 Sep 24 01:35:05 bookcdb amavis[1155]: Module Convert::UUlib 1.4 Sep 24 01:35:05 bookcdb amavis[1155]: Module Crypt::OpenSSL::RSA 0.27 Sep 24 01:35:05 bookcdb amavis[1155]: Module DB_File 1.821 Sep 24 01:35:05 bookcdb amavis[1155]: Module Digest::MD5 2.51 Sep 24 01:35:05 bookcdb amavis[1155]: Module Digest::SHA 5.61 Sep 24 01:35:05 bookcdb amavis[1155]: Module IO::Socket::INET6 2.69 Sep 24 01:35:05 bookcdb amavis[1155]: Module MIME::Entity 5.502 Sep 24 01:35:05 bookcdb amavis[1155]: Module MIME::Parser 5.502 Sep 24 01:35:05 bookcdb amavis[1155]: Module MIME::Tools 5.502 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::DKIM::Signer 0.39 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::DKIM::Verifier 0.39 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::Header 2.08 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::Internet 2.08 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::SPF v2.008 Sep 24 01:35:05 bookcdb amavis[1155]: Module Mail::SpamAssassin 3.003002 Sep 24 01:35:05 bookcdb amavis[1155]: Module Net::DNS 0.66 Sep 24 01:35:05 bookcdb amavis[1155]: Module Net::Server 0.99 Sep 24 01:35:05 bookcdb amavis[1155]: Module NetAddr::IP 4.058 Sep 24 01:35:05 bookcdb amavis[1155]: Module Socket6 0.23 Sep 24 01:35:05 bookcdb amavis[1155]: Module Time::HiRes 1.972101 Sep 24 01:35:05 bookcdb amavis[1155]: Module URI 1.59 Sep 24 01:35:05 bookcdb amavis[1155]: Module Unix::Syslog 1.1 Sep 24 01:35:05 bookcdb amavis[1155]: Amavis::DB code loaded Sep 24 01:35:05 bookcdb amavis[1155]: Amavis::Cache code loaded Sep 24 01:35:05 bookcdb amavis[1155]: SQL base code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: SQL::Log code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: SQL::Quarantine NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: Lookup::SQL code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: Lookup::LDAP code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: AM.PDP-in proto code loaded Sep 24 01:35:05 bookcdb amavis[1155]: SMTP-in proto code loaded Sep 24 01:35:05 bookcdb amavis[1155]: Courier proto code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: SMTP-out proto code loaded Sep 24 01:35:05 bookcdb amavis[1155]: Pipe-out proto code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: BSMTP-out proto code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: Local-out proto code loaded Sep 24 01:35:05 bookcdb amavis[1155]: OS_Fingerprint code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: ANTI-VIRUS code loaded Sep 24 01:35:05 bookcdb amavis[1155]: ANTI-SPAM code loaded Sep 24 01:35:05 bookcdb amavis[1155]: ANTI-SPAM-EXT code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: ANTI-SPAM-C code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: ANTI-SPAM-SA code loaded Sep 24 01:35:05 bookcdb amavis[1155]: Unpackers code loaded Sep 24 01:35:05 bookcdb amavis[1155]: DKIM code loaded Sep 24 01:35:05 bookcdb amavis[1155]: Tools code NOT loaded Sep 24 01:35:05 bookcdb amavis[1155]: Found $file at /usr/bin/file Sep 24 01:35:05 bookcdb amavis[1155]: No $altermime, not using it Sep 24 01:35:05 bookcdb amavis[1155]: Internal decoder for .mail Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .F Sep 24 01:35:05 bookcdb amavis[1155]: Found decoder for .Z at /bin/uncompress Sep 24 01:35:05 bookcdb amavis[1155]: Internal decoder for .gz Sep 24 01:35:05 bookcdb amavis[1155]: Found decoder for .bz2 at /bin/bzip2 -d Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .lzo tried: lzop -d Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .rpm tried: rpm2cpio.pl, rpm2cpio Sep 24 01:35:05 bookcdb amavis[1155]: Found decoder for .cpio at /bin/pax Sep 24 01:35:05 bookcdb amavis[1155]: Found decoder for .tar at /bin/pax Sep 24 01:35:05 bookcdb amavis[1155]: Found decoder for .deb at /usr/bin/ar Sep 24 01:35:05 bookcdb amavis[1155]: Internal decoder for .zip Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .7z tried: 7zr, 7za, 7z Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .rar tried: unrar-free Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .arj tried: arj, unarj Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .arc tried: nomarch, arc Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .zoo tried: zoo Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .lha Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .doc tried: ripole Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .cab tried: cabextract Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .tnef Sep 24 01:35:05 bookcdb amavis[1155]: Internal decoder for .tnef Sep 24 01:35:05 bookcdb amavis[1155]: No decoder for .exe tried: unrar-free; arj, unarj Sep 24 01:35:05 bookcdb amavis[1155]: Using primary internal av scanner code for ClamAV-clamd Sep 24 01:35:05 bookcdb amavis[1155]: Found secondary av scanner ClamAV-clamscan at /usr/bin/clamscan Sep 24 01:35:05 bookcdb amavis[1155]: Creating db in /var/lib/amavis/db/; BerkeleyDB 0.49, libdb 5.1 Sep 24 01:35:05 bookcdb postgrey[1219]: Process Backgrounded Sep 24 01:35:05 bookcdb postgrey[1219]: 2012/09/24-01:35:05 postgrey (type Net::Server::Multiplex) starting! pid(1219) Sep 24 01:35:05 bookcdb postgrey[1219]: Using default listen value of 128 Sep 24 01:35:05 bookcdb postgrey[1219]: Binding to TCP port 10023 on host localhost#012 Sep 24 01:35:05 bookcdb postgrey[1219]: Setting gid to "116 116" Sep 24 01:35:05 bookcdb postgrey[1219]: Setting uid to "110" Sep 24 01:35:06 bookcdb spamd[1231]: logger: removing stderr method Sep 24 01:35:08 bookcdb spamd[1233]: spamd: server started on port 783/tcp (running version 3.3.2) Sep 24 01:35:08 bookcdb spamd[1233]: spamd: server pid: 1233 Sep 24 01:35:08 bookcdb spamd[1233]: spamd: server successfully spawned child process, pid 1238 Sep 24 01:35:08 bookcdb spamd[1233]: spamd: server successfully spawned child process, pid 1240 Sep 24 01:35:08 bookcdb spamd[1233]: prefork: child states: SI Sep 24 01:35:08 bookcdb spamd[1233]: prefork: child states: II Sep 24 01:35:15 bookcdb postfix/master[1729]: daemon started -- version 2.9.3, configuration /etc/postfix Sep 24 01:36:08 bookcdb postfix/smtpd[1995]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Sep 24 01:36:08 bookcdb postfix/smtpd[1995]: warning: hostname localhost does not resolve to address ::1: No address associated with hostname Sep 24 01:36:08 bookcdb postfix/smtpd[1995]: connect from unknown[::1] Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: error: open database /etc/postfix/transport.db: No such file or directory Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport lookup error for "*" Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport lookup error for "root@localhost" Sep 24 01:36:51 bookcdb postfix/trivial-rewrite[1999]: warning: transport_maps lookup failure Sep 24 01:37:00 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:37:00 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport lookup error for "fmaster@localhost" Sep 24 01:37:00 bookcdb postfix/trivial-rewrite[1999]: warning: transport_maps lookup failure Sep 24 01:37:00 bookcdb postfix/smtpd[1995]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <fmaster@localhost>: Temporary lookup failure; from=<root@localhost> to=<fmaster@localhost> proto=SMTP Sep 24 01:37:28 bookcdb dovecot: imap-login: Login: user=<mkadiri89>, method=PLAIN, rip=::1, lip=::1, mpid=2730, secured Sep 24 01:37:28 bookcdb dovecot: imap(mkadiri89): Disconnected: Logged out bytes=44/697 Sep 24 01:37:29 bookcdb dovecot: imap-login: Login: user=<mkadiri89>, method=PLAIN, rip=::1, lip=::1, mpid=2732, secured Sep 24 01:37:29 bookcdb dovecot: imap(mkadiri89): Disconnected: Logged out bytes=464/1303 Sep 24 01:37:29 bookcdb dovecot: imap-login: Login: user=<mkadiri89>, method=PLAIN, rip=::1, lip=::1, mpid=2734, secured Sep 24 01:37:29 bookcdb dovecot: imap(mkadiri89): Disconnected: Logged out bytes=117/1395 Sep 24 01:37:31 bookcdb dovecot: imap-login: Login: user=<mkadiri89>, method=PLAIN, rip=::1, lip=::1, mpid=2737, secured Sep 24 01:37:31 bookcdb dovecot: imap(mkadiri89): Disconnected: Logged out bytes=117/1395 Sep 24 01:37:49 bookcdb dovecot: imap-login: Login: user=<root>, method=PLAIN, rip=::1, lip=::1, mpid=2739, secured Sep 24 01:37:49 bookcdb dovecot: imap: Error: user root: Invalid settings in userdb: userdb returned 0 as uid Sep 24 01:37:49 bookcdb dovecot: imap: Error: Invalid user settings. Refer to server log for more information. Sep 24 01:37:54 bookcdb dovecot: imap-login: Login: user=<root>, method=PLAIN, rip=::1, lip=::1, mpid=2741, secured Sep 24 01:37:54 bookcdb dovecot: imap: Error: user root: Invalid settings in userdb: userdb returned 0 as uid Sep 24 01:37:54 bookcdb dovecot: imap: Error: Invalid user settings. Refer to server log for more information. Sep 24 01:38:04 bookcdb dovecot: imap-login: Login: user=<info>, method=PLAIN, rip=::1, lip=::1, mpid=2743, secured Sep 24 01:38:04 bookcdb dovecot: imap(info): Disconnected: Logged out bytes=44/697 Sep 24 01:38:04 bookcdb dovecot: imap-login: Login: user=<info>, method=PLAIN, rip=::1, lip=::1, mpid=2745, secured Sep 24 01:38:04 bookcdb dovecot: imap(info): Disconnected: Logged out bytes=464/1303 Sep 24 01:38:04 bookcdb dovecot: imap-login: Login: user=<info>, method=PLAIN, rip=::1, lip=::1, mpid=2747, secured Sep 24 01:38:04 bookcdb dovecot: imap(info): Disconnected: Logged out bytes=117/1395 Sep 24 01:38:55 bookcdb postfix/smtpd[1995]: disconnect from unknown[::1] Sep 24 01:38:58 bookcdb postfix/smtpd[1995]: warning: hostname localhost does not resolve to address ::1: No address associated with hostname Sep 24 01:38:58 bookcdb postfix/smtpd[1995]: connect from unknown[::1] Sep 24 01:39:11 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Sep 24 01:39:11 bookcdb postfix/trivial-rewrite[1999]: warning: hash:/etc/postfix/transport lookup error for "info@localhost" Sep 24 01:39:11 bookcdb postfix/trivial-rewrite[1999]: warning: transport_maps lookup failure Sep 24 01:39:37 bookcdb postfix/smtpd[1995]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <fmaster@localhost>: Temporary lookup failure; from=<info@localhost> to=<fmaster@localhost> proto=SMTP Sep 24 01:39:47 bookcdb postfix/smtpd[1995]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <fmaster@localhost>: Temporary lookup failure; from=<info@localhost> to=<fmaster@localhost> proto=SMTP Sep 24 01:40:13 bookcdb postfix/smtpd[1995]: NOQUEUE: reject: RCPT from unknown[::1]: 451 4.3.0 <info@localhost>: Temporary lookup failure; from=<info@localhost> to=<info@localhost> proto=SMTP Sep 24 01:43:08 bookcdb postfix/smtpd[1995]: disconnect from unknown[::1] Sep 24 01:46:08 bookcdb postfix/anvil[1998]: statistics: max connection rate 1/60s for (smtp:::1) at Sep 24 01:36:08 Sep 24 01:46:08 bookcdb postfix/anvil[1998]: statistics: max connection count 1 for (smtp:::1) at Sep 24 01:36:08 Sep 24 01:46:08 bookcdb postfix/anvil[1998]: statistics: max cache size 1 at Sep 24 01:36:08 Sep 24 01:48:05 bookcdb dovecot: imap-login: Login: user=<info>, method=PLAIN, rip=::1, lip=::1, mpid=2805, secured Sep 24 01:48:05 bookcdb dovecot: imap(info): Disconnected: Logged out bytes=85/681 Sep 24 01:51:30 bookcdb dovecot: imap-login: Login: user=<info>, method=PLAIN, rip=::1, lip=::1, mpid=2815, secured Sep 24 01:51:30 bookcdb dovecot: imap(info): Disconnected: Logged out bytes=117/1395 Sep 24 02:05:15 bookcdb postfix/qmgr[1745]: 2EA006E0B32: from=<[email protected]>, size=439, nrcpt=1 (queue active) Sep 24 02:05:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 02:05:15 bookcdb postfix/qmgr[1745]: E76996E09B2: from=<[email protected]>, size=439, nrcpt=1 (queue active) Sep 24 02:05:15 bookcdb postfix/error[2842]: 2EA006E0B32: to=<[email protected]>, relay=none, delay=8391, delays=8391/0.05/0/0.09, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 02:05:16 bookcdb postfix/error[2843]: E76996E09B2: to=<[email protected]>, relay=none, delay=8416, delays=8416/0.03/0/0.11, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 02:30:15 bookcdb postfix/qmgr[1745]: D0C596E0B34: from=<[email protected]>, size=442, nrcpt=1 (queue active) Sep 24 02:30:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 02:30:15 bookcdb postfix/error[2914]: D0C596E0B34: to=<[email protected]>, relay=none, delay=9551, delays=9551/0.01/0/0.08, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 02:35:15 bookcdb postfix/qmgr[1745]: 2E5C36E0A07: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 02:35:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 02:35:15 bookcdb postfix/qmgr[1745]: 0EA3A6E0ACC: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 02:35:15 bookcdb postfix/error[2926]: 2E5C36E0A07: to=<[email protected]>, orig_to=<root>, relay=none, delay=34386, delays=34386/0.03/0/0.1, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 02:35:15 bookcdb postfix/error[2927]: 0EA3A6E0ACC: to=<[email protected]>, orig_to=<root>, relay=none, delay=34299, delays=34298/0.02/0/0.12, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 03:15:15 bookcdb postfix/qmgr[1745]: 2EA006E0B32: from=<[email protected]>, size=439, nrcpt=1 (queue active) Sep 24 03:15:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 03:15:15 bookcdb postfix/qmgr[1745]: E76996E09B2: from=<[email protected]>, size=439, nrcpt=1 (queue active) Sep 24 03:15:15 bookcdb postfix/error[3025]: 2EA006E0B32: to=<[email protected]>, relay=none, delay=12590, delays=12590/0.01/0/0.07, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 03:15:15 bookcdb postfix/error[3026]: E76996E09B2: to=<[email protected]>, relay=none, delay=12616, delays=12616/0.01/0/0.09, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 03:40:15 bookcdb postfix/qmgr[1745]: D0C596E0B34: from=<[email protected]>, size=442, nrcpt=1 (queue active) Sep 24 03:40:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 03:40:15 bookcdb postfix/error[3097]: D0C596E0B34: to=<[email protected]>, relay=none, delay=13752, delays=13752/0.01/0/0.07, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 03:45:15 bookcdb postfix/qmgr[1745]: 2E5C36E0A07: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 03:45:15 bookcdb postfix/qmgr[1745]: warning: connect to transport private/smtp-amavis: No such file or directory Sep 24 03:45:15 bookcdb postfix/qmgr[1745]: 0EA3A6E0ACC: from=<[email protected]>, size=438, nrcpt=1 (queue active) Sep 24 03:45:15 bookcdb postfix/error[3129]: 2E5C36E0A07: to=<[email protected]>, orig_to=<root>, relay=none, delay=38586, delays=38586/0.01/0/0.09, dsn=4.3.0, status=deferred (mail transport unavailable) Sep 24 03:45:15 bookcdb postfix/error[3130]: 0EA3A6E0ACC: to=<[email protected]>, orig_to=<root>, relay=none, delay=38498, delays=38498/0.01/0/0.08, dsn=4.3.0, status=deferred (mail transport unavailable) postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix content_filter = smtp-amavis:[127.0.0.1]:10024 home_mailbox = Maildir/ inet_interfaces = all inet_protocols = all mailbox_command = mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = server1.bookcdb.com, bookcdb.com, localhost.bookcdb.com, localho st, bookcdb.com myhostname = server1.bookcdb.com mynetworks = 127.0.0.0/8 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relay_domains = lists.bookcdb.com relayhost = smtp_tls_note_starttls_offer = yes smtp_tls_security_level = may smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,rejec t_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_auth_only = no smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_security_level = may smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_tls_session_cache_timeout = 3600s smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• Unable to connect to Github for the first time

  - by MaxMackie

  This is my first time with Git and I'm trying to set it up on my box. I added my key to my profile in the Github web interface. When I try to connect... : max@linux-vwzy:~> ssh [email protected] The authenticity of host 'github.com (207.97.227.239)' can't be established. RSA key fingerprint is xx Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added 'github.com,207.97.227.239' (RSA) to the list of known hosts. PTY allocation request failed on channel 0 max@linux-vwzy:~> ssh-add ~/.ssh/id_rsa Identity added: /home/max/.ssh/id_rsa (/home/max/.ssh/id_rsa) max@linux-vwzy:~> ssh [email protected] PTY allocation request failed on channel 0 I'm supposed to be getting some kind of welcome message however, I'm not.

  Read the article

• Wake On Lan (WOL) for Realtek RTL8101E/RTL8102E

  - by Heisennberg

  I'm unsuccessfully trying to get Wake on Lan to work with my local server (IP Address : 192.168.0.2, distro Ubuntu 12.04.3 LTS) which has a Realtek RTL8101E/RTL8102E ethernet card. The computer sending the WOL is a Macbook Pro which is connected on the same network. Yet the server fails to start. Here what I have done so far : name@serverName ~ $ cat /proc/acpi/wakeup Device S-state Status Sysfs node HDEF S3 *disabled pci:0000:00:1b.0 PXSX S3 *disabled PXSX S0 *enabled pci:0000:04:00.0 PXSX S0 *disabled USB1 S3 *enabled pci:0000:00:1d.0 USB2 S3 *enabled pci:0000:00:1d.1 USB3 S3 *enabled pci:0000:00:1d.2 USB5 S3 *enabled pci:0000:00:1a.1 EHC1 S3 *enabled pci:0000:00:1d.7 EHC2 S3 *enabled pci:0000:00:1a.7 name@serverName ~ $ lspci ------ 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 01) ------ name@serverName ~ $ sudo ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Link partner advertised pause frame use: Symmetric Receive-only Link partner advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) drv probe ifdown ifup Link detected: yes and I'm calling the WOL with : name@serverName ~ $ wakeonlan xx:xx:xx:xx:xx` Sending magic packet to 255.255.255.255:9 with xx:xx:xx:xx:xx I have succesfully activated the WOL option in my computer BIOS. Any idea ?

  Read the article

• validation properties by attribute

  - by netmajor

  I create class with two property - name,link(below). I use simple property validation by Required and StringLength attribute. I bind this class object to WPF ListBox(with textBoxs). But when I have textbox empty or write words longer than 8 sign nothing happens :/ What should I do to fires ErrorMessage? Or how to implement validation in other way ? I also try use : if (value is int) { throw new ArgumentException("Wpisales stringa!!"); } But it only fires in debug mode :/ My class with implementation of attribute validation: public class RssInfo : INotifyPropertyChanged { public RssInfo() { } public RssInfo(string _nazwa, string _link) { nazwa = _nazwa; link = _link; } private string nazwa; [Required(ErrorMessage = "To pole jest obowiazkowe nAZWA")] public string Nazwa { get { return nazwa; } set { if (value != nazwa) { nazwa = value; onPropertyChanged("Nazwa"); } if (value is int) { throw new ArgumentException("Wpisales stringa!!"); } } } private string link; [Required(ErrorMessage="To pole jest obowiazkowe link")] [StringLength(8, ErrorMessage = "Link cannot be longer than 8 characters")] public string Link { get { return link; } set { if (value != link) { link = value; onPropertyChanged("Link"); } } } #region INotifyPropertyChanged Members public event PropertyChangedEventHandler PropertyChanged; #endregion private void onPropertyChanged(string propertyName) { if (this.PropertyChanged != null) { PropertyChanged(this, new PropertyChangedEventArgs(propertyName)); } } }

  Read the article

• GCC4.2 build warning : Default deployment version is greater than the max value for the iPhone simul

  - by user255403

  Hi I upgraded an iPhone project from the 2.2.1 SDK to 3.0 SDK recently... And when I build the project I am getting the following warning: GCC 4.2 default deployment target 10.6.2 for architecture 'i386' and variant 'normal' is greater than the maximum value 10.6 for the Simulator - iPhone OS 3.1.2 SDK I have the iPhone OS Deployment target set to iPhone OS 3.0 Any idea what could be causing this 'warning' to show up. Regards - SY

  Read the article

• Project Euler 8: (Iron)Python

  - by Ben Griswold

  In my attempt to learn (Iron)Python out in the open, here’s my solution for Project Euler Problem 8.  As always, any feedback is welcome. # Euler 8 # http://projecteuler.net/index.php?section=problems&id=8 # Find the greatest product of five consecutive digits # in the following 1000-digit number import time start = time.time() number = '\ 73167176531330624919225119674426574742355349194934\ 96983520312774506326239578318016984801869478851843\ 85861560789112949495459501737958331952853208805511\ 12540698747158523863050715693290963295227443043557\ 66896648950445244523161731856403098711121722383113\ 62229893423380308135336276614282806444486645238749\ 30358907296290491560440772390713810515859307960866\ 70172427121883998797908792274921901699720888093776\ 65727333001053367881220235421809751254540594752243\ 52584907711670556013604839586446706324415722155397\ 53697817977846174064955149290862569321978468622482\ 83972241375657056057490261407972968652414535100474\ 82166370484403199890008895243450658541227588666881\ 16427171479924442928230863465674813919123162824586\ 17866458359124566529476545682848912883142607690042\ 24219022671055626321111109370544217506941658960408\ 07198403850962455444362981230987879927244284909188\ 84580156166097919133875499200524063689912560717606\ 05886116467109405077541002256983155200055935729725\ 71636269561882670428252483600823257530420752963450' max = 0 for i in xrange(0, len(number) - 5): nums = [int(x) for x in number[i:i+5]] val = reduce(lambda agg, x: agg*x, nums) if val > max: max = val print max print "Elapsed Time:", (time.time() - start) * 1000, "millisecs" a=raw_input('Press return to continue')

  Read the article

• How to implement 3D model interaction like 3D max or other game editors?

  - by Rushi

  I am developing game editor.To detect mouse hit on 3D model I am using mouse picking concept. But I want to give interactive arrows functionality like other game editor with actual arrows at the center of model in three direction. How to achieve this..?

  Read the article

• Pitfalls and practical Use-Cases: Toplink, Hibernate, Eclipse Link, Ibatis ...

  - by Martin K.

  I worked a lot with Hibernate as my JPA implementation. In most cases it works fine! But I have also seen a lot of pitfalls: Remoting with persisted Objects is difficult, because Hibernate replaces the Java collections with its own collection implementation. So the every client must have the Hibernate .jar libraries. You have to take care on LazyLoading exceptions etc. One way to get around this problem is the use of webservices. Dirty checking is done against the Database without any lock. "Delayed SQL", causes that the data access isn't ACID compliant. (Lost data...) Implict Updates So we don't know if an object is modified or not (commit causes updates). Are there similar issues with Toplink, Eclipse Link and Ibatis? When should I use them? Have they a similar performance? Are there reasons to choose Eclipse Link/Toplink... over Hibernate?

  Read the article

• Intel 82576 Network card

  - by No1_Melman

  I have an Intel dual port pcie NIC card with two 82576 interfaces according to ubuntu 12.04. I run the command sudo lshw -html > /home/melman/Documents/hardware.html and it shows both of the interfaces but they're grayed out?! How can enable them? ifconfig output: bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.100.2 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr e0:69:95:d1:db:ff inet addr:192.168.10.63 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::e269:95ff:fed1:dbff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2903 errors:0 dropped:0 overruns:0 frame:0 TX packets:2627 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1524738 (1.5 MB) TX bytes:430196 (430.1 KB) Interrupt:20 Memory:f7f00000-f7f20000 eth3 Link encap:Ethernet HWaddr 00:50:b6:50:a7:f9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:1b:21:6e:99:77 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c00000-f7c20000 eth5 Link encap:Ethernet HWaddr 00:1b:21:6e:99:76 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c20000-f7c40000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:246 errors:0 dropped:0 overruns:0 frame:0 TX packets:246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17584 (17.5 KB) TX bytes:17584 (17.5 KB)

  Read the article

• C#/.NET Little Wonders: The Generic Func Delegates

  - by James Michael Hare

  Once again, in this series of posts I look at the parts of the .NET Framework that may seem trivial, but can help improve your code by making it easier to write and maintain. The index of all my past little wonders posts can be found here. Back in one of my three original “Little Wonders” Trilogy of posts, I had listed generic delegates as one of the Little Wonders of .NET.  Later, someone posted a comment saying said that they would love more detail on the generic delegates and their uses, since my original entry just scratched the surface of them. Last week, I began our look at some of the handy generic delegates built into .NET with a description of delegates in general, and the Action family of delegates.  For this week, I’ll launch into a look at the Func family of generic delegates and how they can be used to support generic, reusable algorithms and classes. Quick Delegate Recap Delegates are similar to function pointers in C++ in that they allow you to store a reference to a method.  They can store references to either static or instance methods, and can actually be used to chain several methods together in one delegate. Delegates are very type-safe and can be satisfied with any standard method, anonymous method, or a lambda expression.  They can also be null as well (refers to no method), so care should be taken to make sure that the delegate is not null before you invoke it. Delegates are defined using the keyword delegate, where the delegate’s type name is placed where you would typically place the method name: 1: // This delegate matches any method that takes string, returns nothing 2: public delegate void Log(string message); This delegate defines a delegate type named Log that can be used to store references to any method(s) that satisfies its signature (whether instance, static, lambda expression, etc.). Delegate instances then can be assigned zero (null) or more methods using the operator = which replaces the existing delegate chain, or by using the operator += which adds a method to the end of a delegate chain: 1: // creates a delegate instance named currentLogger defaulted to Console.WriteLine (static method) 2: Log currentLogger = Console.Out.WriteLine; 3:  4: // invokes the delegate, which writes to the console out 5: currentLogger("Hi Standard Out!"); 6:  7: // append a delegate to Console.Error.WriteLine to go to std error 8: currentLogger += Console.Error.WriteLine; 9:  10: // invokes the delegate chain and writes message to std out and std err 11: currentLogger("Hi Standard Out and Error!"); While delegates give us a lot of power, it can be cumbersome to re-create fairly standard delegate definitions repeatedly, for this purpose the generic delegates were introduced in various stages in .NET.  These support various method types with particular signatures. Note: a caveat with generic delegates is that while they can support multiple parameters, they do not match methods that contains ref or out parameters. If you want to a delegate to represent methods that takes ref or out parameters, you will need to create a custom delegate. We’ve got the Func… delegates Just like it’s cousin, the Action delegate family, the Func delegate family gives us a lot of power to use generic delegates to make classes and algorithms more generic.  Using them keeps us from having to define a new delegate type when need to make a class or algorithm generic. Remember that the point of the Action delegate family was to be able to perform an “action” on an item, with no return results.  Thus Action delegates can be used to represent most methods that take 0 to 16 arguments but return void.  You can assign a method The Func delegate family was introduced in .NET 3.5 with the advent of LINQ, and gives us the power to define a function that can be called on 0 to 16 arguments and returns a result.  Thus, the main difference between Action and Func, from a delegate perspective, is that Actions return nothing, but Funcs return a result. The Func family of delegates have signatures as follows: Func<TResult> – matches a method that takes no arguments, and returns value of type TResult. Func<T, TResult> – matches a method that takes an argument of type T, and returns value of type TResult. Func<T1, T2, TResult> – matches a method that takes arguments of type T1 and T2, and returns value of type TResult. Func<T1, T2, …, TResult> – and so on up to 16 arguments, and returns value of type TResult. These are handy because they quickly allow you to be able to specify that a method or class you design will perform a function to produce a result as long as the method you specify meets the signature. For example, let’s say you were designing a generic aggregator, and you wanted to allow the user to define how the values will be aggregated into the result (i.e. Sum, Min, Max, etc…).  To do this, we would ask the user of our class to pass in a method that would take the current total, the next value, and produce a new total.  A class like this could look like: 1: public sealed class Aggregator<TValue, TResult> 2: { 3: // holds method that takes previous result, combines with next value, creates new result 4: private Func<TResult, TValue, TResult> _aggregationMethod; 5:  6: // gets or sets the current result of aggregation 7: public TResult Result { get; private set; } 8:  9: // construct the aggregator given the method to use to aggregate values 10: public Aggregator(Func<TResult, TValue, TResult> aggregationMethod = null) 11: { 12: if (aggregationMethod == null) throw new ArgumentNullException("aggregationMethod"); 13:  14: _aggregationMethod = aggregationMethod; 15: } 16:  17: // method to add next value 18: public void Aggregate(TValue nextValue) 19: { 20: // performs the aggregation method function on the current result and next and sets to current result 21: Result = _aggregationMethod(Result, nextValue); 22: } 23: } Of course, LINQ already has an Aggregate extension method, but that works on a sequence of IEnumerable<T>, whereas this is designed to work more with aggregating single results over time (such as keeping track of a max response time for a service). We could then use this generic aggregator to find the sum of a series of values over time, or the max of a series of values over time (among other things): 1: // creates an aggregator that adds the next to the total to sum the values 2: var sumAggregator = new Aggregator<int, int>((total, next) => total + next); 3:  4: // creates an aggregator (using static method) that returns the max of previous result and next 5: var maxAggregator = new Aggregator<int, int>(Math.Max); So, if we were timing the response time of a web method every time it was called, we could pass that response time to both of these aggregators to get an idea of the total time spent in that web method, and the max time spent in any one call to the web method: 1: // total will be 13 and max 13 2: int responseTime = 13; 3: sumAggregator.Aggregate(responseTime); 4: maxAggregator.Aggregate(responseTime); 5:  6: // total will be 20 and max still 13 7: responseTime = 7; 8: sumAggregator.Aggregate(responseTime); 9: maxAggregator.Aggregate(responseTime); 10:  11: // total will be 40 and max now 20 12: responseTime = 20; 13: sumAggregator.Aggregate(responseTime); 14: maxAggregator.Aggregate(responseTime); The Func delegate family is useful for making generic algorithms and classes, and in particular allows the caller of the method or user of the class to specify a function to be performed in order to generate a result. What is the result of a Func delegate chain? If you remember, we said earlier that you can assign multiple methods to a delegate by using the += operator to chain them.  So how does this affect delegates such as Func that return a value, when applied to something like the code below? 1: Func<int, int, int> combo = null; 2:  3: // What if we wanted to aggregate the sum and max together? 4: combo += (total, next) => total + next; 5: combo += Math.Max; 6:  7: // what is the result? 8: var comboAggregator = new Aggregator<int, int>(combo); Well, in .NET if you chain multiple methods in a delegate, they will all get invoked, but the result of the delegate is the result of the last method invoked in the chain.  Thus, this aggregator would always result in the Math.Max() result.  The other chained method (the sum) gets executed first, but it’s result is thrown away: 1: // result is 13 2: int responseTime = 13; 3: comboAggregator.Aggregate(responseTime); 4:  5: // result is still 13 6: responseTime = 7; 7: comboAggregator.Aggregate(responseTime); 8:  9: // result is now 20 10: responseTime = 20; 11: comboAggregator.Aggregate(responseTime); So remember, you can chain multiple Func (or other delegates that return values) together, but if you do so you will only get the last executed result. Func delegates and co-variance/contra-variance in .NET 4.0 Just like the Action delegate, as of .NET 4.0, the Func delegate family is contra-variant on its arguments.  In addition, it is co-variant on its return type.  To support this, in .NET 4.0 the signatures of the Func delegates changed to: Func<out TResult> – matches a method that takes no arguments, and returns value of type TResult (or a more derived type). Func<in T, out TResult> – matches a method that takes an argument of type T (or a less derived type), and returns value of type TResult(or a more derived type). Func<in T1, in T2, out TResult> – matches a method that takes arguments of type T1 and T2 (or less derived types), and returns value of type TResult (or a more derived type). Func<in T1, in T2, …, out TResult> – and so on up to 16 arguments, and returns value of type TResult (or a more derived type). Notice the addition of the in and out keywords before each of the generic type placeholders.  As we saw last week, the in keyword is used to specify that a generic type can be contra-variant -- it can match the given type or a type that is less derived.  However, the out keyword, is used to specify that a generic type can be co-variant -- it can match the given type or a type that is more derived. On contra-variance, if you are saying you need an function that will accept a string, you can just as easily give it an function that accepts an object.  In other words, if you say “give me an function that will process dogs”, I could pass you a method that will process any animal, because all dogs are animals.  On the co-variance side, if you are saying you need a function that returns an object, you can just as easily pass it a function that returns a string because any string returned from the given method can be accepted by a delegate expecting an object result, since string is more derived.  Once again, in other words, if you say “give me a method that creates an animal”, I can pass you a method that will create a dog, because all dogs are animals. It really all makes sense, you can pass a more specific thing to a less specific parameter, and you can return a more specific thing as a less specific result.  In other words, pay attention to the direction the item travels (parameters go in, results come out).  Keeping that in mind, you can always pass more specific things in and return more specific things out. For example, in the code below, we have a method that takes a Func<object> to generate an object, but we can pass it a Func<string> because the return type of object can obviously accept a return value of string as well: 1: // since Func<object> is co-variant, this will access Func<string>, etc... 2: public static string Sequence(int count, Func<object> generator) 3: { 4: var builder = new StringBuilder(); 5:  6: for (int i=0; i<count; i++) 7: { 8: object value = generator(); 9: builder.Append(value); 10: } 11:  12: return builder.ToString(); 13: } Even though the method above takes a Func<object>, we can pass a Func<string> because the TResult type placeholder is co-variant and accepts types that are more derived as well: 1: // delegate that's typed to return string. 2: Func<string> stringGenerator = () => DateTime.Now.ToString(); 3:  4: // This will work in .NET 4.0, but not in previous versions 5: Sequence(100, stringGenerator); Previous versions of .NET implemented some forms of co-variance and contra-variance before, but .NET 4.0 goes one step further and allows you to pass or assign an Func<A, BResult> to a Func<Y, ZResult> as long as A is less derived (or same) as Y, and BResult is more derived (or same) as ZResult. Sidebar: The Func and the Predicate A method that takes one argument and returns a bool is generally thought of as a predicate.  Predicates are used to examine an item and determine whether that item satisfies a particular condition.  Predicates are typically unary, but you may also have binary and other predicates as well. Predicates are often used to filter results, such as in the LINQ Where() extension method: 1: var numbers = new[] { 1, 2, 4, 13, 8, 10, 27 }; 2:  3: // call Where() using a predicate which determines if the number is even 4: var evens = numbers.Where(num => num % 2 == 0); As of .NET 3.5, predicates are typically represented as Func<T, bool> where T is the type of the item to examine.  Previous to .NET 3.5, there was a Predicate<T> type that tended to be used (which we’ll discuss next week) and is still supported, but most developers recommend using Func<T, bool> now, as it prevents confusion with overloads that accept unary predicates and binary predicates, etc.: 1: // this seems more confusing as an overload set, because of Predicate vs Func 2: public static SomeMethod(Predicate<int> unaryPredicate) { } 3: public static SomeMethod(Func<int, int, bool> binaryPredicate) { } 4:  5: // this seems more consistent as an overload set, since just uses Func 6: public static SomeMethod(Func<int, bool> unaryPredicate) { } 7: public static SomeMethod(Func<int, int, bool> binaryPredicate) { } Also, even though Predicate<T> and Func<T, bool> match the same signatures, they are separate types!  Thus you cannot assign a Predicate<T> instance to a Func<T, bool> instance and vice versa: 1: // the same method, lambda expression, etc can be assigned to both 2: Predicate<int> isEven = i => (i % 2) == 0; 3: Func<int, bool> alsoIsEven = i => (i % 2) == 0; 4:  5: // but the delegate instances cannot be directly assigned, strongly typed! 6: // ERROR: cannot convert type... 7: isEven = alsoIsEven; 8:  9: // however, you can assign by wrapping in a new instance: 10: isEven = new Predicate<int>(alsoIsEven); 11: alsoIsEven = new Func<int, bool>(isEven); So, the general advice that seems to come from most developers is that Predicate<T> is still supported, but we should use Func<T, bool> for consistency in .NET 3.5 and above. Sidebar: Func as a Generator for Unit Testing One area of difficulty in unit testing can be unit testing code that is based on time of day.  We’d still want to unit test our code to make sure the logic is accurate, but we don’t want the results of our unit tests to be dependent on the time they are run. One way (of many) around this is to create an internal generator that will produce the “current” time of day.  This would default to returning result from DateTime.Now (or some other method), but we could inject specific times for our unit testing.  Generators are typically methods that return (generate) a value for use in a class/method. For example, say we are creating a CacheItem<T> class that represents an item in the cache, and we want to make sure the item shows as expired if the age is more than 30 seconds.  Such a class could look like: 1: // responsible for maintaining an item of type T in the cache 2: public sealed class CacheItem<T> 3: { 4: // helper method that returns the current time 5: private static Func<DateTime> _timeGenerator = () => DateTime.Now; 6:  7: // allows internal access to the time generator 8: internal static Func<DateTime> TimeGenerator 9: { 10: get { return _timeGenerator; } 11: set { _timeGenerator = value; } 12: } 13:  14: // time the item was cached 15: public DateTime CachedTime { get; private set; } 16:  17: // the item cached 18: public T Value { get; private set; } 19:  20: // item is expired if older than 30 seconds 21: public bool IsExpired 22: { 23: get { return _timeGenerator() - CachedTime > TimeSpan.FromSeconds(30.0); } 24: } 25:  26: // creates the new cached item, setting cached time to "current" time 27: public CacheItem(T value) 28: { 29: Value = value; 30: CachedTime = _timeGenerator(); 31: } 32: } Then, we can use this construct to unit test our CacheItem<T> without any time dependencies: 1: var baseTime = DateTime.Now; 2:  3: // start with current time stored above (so doesn't drift) 4: CacheItem<int>.TimeGenerator = () => baseTime; 5:  6: var target = new CacheItem<int>(13); 7:  8: // now add 15 seconds, should still be non-expired 9: CacheItem<int>.TimeGenerator = () => baseTime.AddSeconds(15); 10:  11: Assert.IsFalse(target.IsExpired); 12:  13: // now add 31 seconds, should now be expired 14: CacheItem<int>.TimeGenerator = () => baseTime.AddSeconds(31); 15:  16: Assert.IsTrue(target.IsExpired); Now we can unit test for 1 second before, 1 second after, 1 millisecond before, 1 day after, etc.  Func delegates can be a handy tool for this type of value generation to support more testable code.  Summary Generic delegates give us a lot of power to make truly generic algorithms and classes.  The Func family of delegates is a great way to be able to specify functions to calculate a result based on 0-16 arguments.  Stay tuned in the weeks that follow for other generic delegates in the .NET Framework!   Tweet Technorati Tags: .NET, C#, CSharp, Little Wonders, Generics, Func, Delegates

  Read the article

• How can I test if an oriented rectangle contains another oriented rectangle?

  - by gronzzz

  I have the following situation: To detect whether is the red rectangle is inside orange area I use this function: - (BOOL)isTile:(CGPoint)tile insideCustomAreaMin:(CGPoint)min max:(CGPoint)max { if ((tile.x < min.x) || (tile.x > max.x) || (tile.y < min.y) || (tile.y > max.y)) { NSLog(@" Object is out of custom area! "); return NO; } return YES; } But what if I need to detect whether the red tile is inside of the blue rectangle? I wrote this function which uses the world position: - (BOOL)isTileInsidePlayableArea:(CGPoint)tile { // get world positions from tiles CGPoint rt = [[CoordinateFunctions shared] worldFromTile:ccp(24, 0)]; CGPoint lb = [[CoordinateFunctions shared] worldFromTile:ccp(24, 48)]; CGPoint worldTile = [[CoordinateFunctions shared] worldFromTile:tile]; return [self isTile:worldTile insideCustomAreaMin:ccp(lb.x, lb.y) max:ccp(rt.x, rt.y)]; } How could I do this without converting to the global position of the tiles?

  Read the article

• How to determine if you should use full or differential backup?

  - by Peter Larsson

  Or ask yourself, "How much of the database has changed since last backup?". Here is a simple script that will tell you how much (in percent) have changed in the database since last backup. -- Prepare staging table for all DBCC outputs DECLARE @Sample TABLE         (             Col1 VARCHAR(MAX) NOT NULL,             Col2 VARCHAR(MAX) NOT NULL,             Col3 VARCHAR(MAX) NOT NULL,             Col4 VARCHAR(MAX) NOT NULL,             Col5 VARCHAR(MAX)         )   -- Some intermediate variables for controlling loop DECLARE @FileNum BIGINT = 1,         @PageNum BIGINT = 6,         @SQL VARCHAR(100),         @Error INT,         @DatabaseName SYSNAME = 'Yoda'   -- Loop all files to the very end WHILE 1 = 1     BEGIN         BEGIN TRY             -- Build the SQL string to execute             SET     @SQL = 'DBCC PAGE(' + QUOTENAME(@DatabaseName) + ', ' + CAST(@FileNum AS VARCHAR(50)) + ', '                             + CAST(@PageNum AS VARCHAR(50)) + ', 3) WITH TABLERESULTS'               -- Insert the DBCC output in the staging table             INSERT  @Sample                     (                         Col1,                         Col2,                         Col3,                         Col4                     )             EXEC    (@SQL)               -- DCM pages exists at an interval             SET    @PageNum += 511232         END TRY           BEGIN CATCH             -- If error and first DCM page does not exist, all files are read             IF @PageNum = 6                 BREAK             ELSE                 -- If no more DCM, increase filenum and start over                 SELECT  @FileNum += 1,                         @PageNum = 6         END CATCH     END   -- Delete all records not related to diff information DELETE FROM    @Sample WHERE   Col1 NOT LIKE 'DIFF%'   -- Split the range UPDATE  @Sample SET     Col5 = PARSENAME(REPLACE(Col3, ' - ', '.'), 1),         Col3 = PARSENAME(REPLACE(Col3, ' - ', '.'), 2)   -- Remove last paranthesis UPDATE  @Sample SET     Col3 = RTRIM(REPLACE(Col3, ')', '')),         Col5 = RTRIM(REPLACE(Col5, ')', ''))   -- Remove initial information about filenum UPDATE  @Sample SET     Col3 = SUBSTRING(Col3, CHARINDEX(':', Col3) + 1, 8000),         Col5 = SUBSTRING(Col5, CHARINDEX(':', Col5) + 1, 8000)   -- Prepare data outtake ;WITH cteSource(Changed, [PageCount]) AS (     SELECT      Changed,                 SUM(COALESCE(ToPage, FromPage) - FromPage + 1) AS [PageCount]     FROM        (                     SELECT CAST(Col3 AS INT) AS FromPage,                             CAST(NULLIF(Col5, '') AS INT) AS ToPage,                             LTRIM(Col4) AS Changed                     FROM    @Sample                 ) AS d     GROUP BY    Changed     WITH ROLLUP ) -- Present the final result SELECT  COALESCE(Changed, 'TOTAL PAGES') AS Changed,         [PageCount],         100.E * [PageCount] / SUM(CASE WHEN Changed IS NULL THEN 0 ELSE [PageCount] END) OVER () AS Percentage FROM    cteSource

  Read the article

• Bulkinsert from CSV into db (C#) -> max number of rows in a web application?

  - by Swoosh

  Web application - C#, .Net, SQL 2k5. I recently used bulkinsert on an other application and I thought I would like to give it a try. I am going to receive a CSV file with 1000 rows, which will most likely add 500 000 (that is five hundred thousand) records in the database. I don't have any idea yet about this huge amount if it's going to work out well. I am afraid that it will time out. I didn't do any testing yet, but I am pretty sure it would time out eventually. Is there a way to make it not time out (I don't know ... split the bulkinsert into 1000 pieces :D) or I should try to do something like BCP, with a SQL job ...

  Read the article

• Is there a minimum spanning tree that does not contain the min/max weighted edge?

  - by Martin

  If we have an (arbitrary) connected undirected graph G, whose edges have distinct weights, does every MST of G contains the minimum weighted edge? is there an MST of G that does not contain the maximum weighted edge? Also, I'm more thankful if someone can give a hint of the key things one must keep in mind when dealing with such MST questions. Thanks

  Read the article

• How long (max characters) can a datastore entity key_name be? Is it bad to haver very long key_names

  - by indiehacker

  What is the maximum number of characters that can be used to define the key_name of a datastore entity? Is it bad to have very long key_names? For example: Lets say we use key_names of a 170 characters, which is the length of a Twitter message 140 plus 10 numeric characters for latitude and 10 for longtitude and 10 for a timestamp. (Reasoning of such a key_name: So by using such a key_name we can easily and quickly be sure of no duplicate postings, since the same message should not come from the same place and time more than once.)

  Read the article

• Google Webmaster tools Incorrect rel-alternate-hreflang implementation warning message

  - by Noam

  I'm getting this warning msg. in Google webmaster tools Incorrect rel-alternate-hreflang implementation In particular, there seems to be a problem with missing or incorrect bi-directional linking (when page A links with hreflang to page B, there must be a link back from B to A as well). This msg. seems pretty straight forward, but when checking their example pages, I'm not finding anything wrong. I'm using alternate for translation of main site menu, titles, etc.. In each page I have this: <link rel="alternate" hreflang="en" href="http://mydomain.com/page" /> <link rel="alternate" hreflang="jp" href="http://ja.mydomain.com/page" /> <link rel="alternate" hreflang="ko" href="http://ko.mydomain.com/page" /> <link rel="alternate" hreflang="th" href="http://th.mydomain.com/page" /> <link rel="alternate" hreflang="es" href="http://es.mydomain.com/page" /> <link rel="alternate" hreflang="pt" href="http://pt.mydomain.com/page" /> I've double checked this exists in all the 6 pages. This is the first time I've seen this msg although I've implemented this at least 6 months ago, and implementation hasn't changed. Is there any way to check a specific set of pages for these things? Am I missing something in my implementation? We're auto-redirecting people from a location to their specific language, and give them an option to manually change this. I've also just found out about the suggestion for Vary HTTP header - is that relevant and important here?

  Read the article

• Max HTML/CSS Editor: TextWrangler or Aptana or Simple CSS?

  - by Mark H.

  Which do you recommend and why? (I would go textedit, but want to first learn and stick with coding for a while before I spend the money.)

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >