Search Results

Search found 2900 results on 116 pages for 'fingerprint reader'.

Page 106/116 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• In 10.10, USB 3.0 PCI Express card recognized by lspci but not lsusb or dmesg. How to fix?

  - by Paul

  Asus N PC, runs 10.10 x86_64 The Asus N comes with 4 usb 2.0 ports, each labelled 2.0 on the case. Attempting to add two usb 3.0 ports to be provided by a generic usb 3.0 pci express card installed in the pci expres slot. The new card says usb 3.0 and has the blue ports. The card is installed into the laptop unpowered, then the laptop is powered on and boots normally. Nothing happens when a USB 3.0 flash drive is inserted into the usb 3.0 port. uname -a Linux drpaulbrewer-N90SV 2.6.35.8 #1 SMP Fri Jan 14 15:54:11 EST 2011 x86_64 GNU/Linux lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64 Kernel modules: sis-agp 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-fdefffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [f4] Power Management version 2 Capabilities: [70] Subsystem: Silicon Integrated Systems [SiS] PCI-to-PCI bridge Kernel driver in use: pcieport 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) Flags: bus master, medium devsel, latency 0 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 128 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffe0 [size=16] Capabilities: [58] Power Management version 2 Kernel driver in use: pata_sis 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at f9fff000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 21 Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) Subsystem: ASUSTeK Computer Inc. Device 11f5 Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128] I/O ports at cc00 [size=128] Capabilities: [40] Power Management version 2 Kernel driver in use: sis190 Kernel modules: sis190 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 17 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at bc00 [size=4] I/O ports at b800 [size=16] I/O ports at b400 [size=128] Capabilities: [58] Power Management version 2 Kernel driver in use: sata_sis Kernel modules: sata_sis 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: fdf00000-fdffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=06, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe000000-febfffff Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller Subsystem: ASUSTeK Computer Inc. Device 17b3 Flags: bus master, medium devsel, latency 0, IRQ 18 Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce GT 130M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 2021 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fa000000 (64-bit, non-prefetchable) [size=32M] I/O ports at dc00 [size=128] [virtual] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Kernel driver in use: nvidia Kernel modules: nvidia-current, nouveau, nvidiafb 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Device 1a3b:1067 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fdff0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Kernel driver in use: ath9k Kernel modules: ath9k 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at febfe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 lsusb Bus 003 Device 002: ID 0b05:1751 ASUSTek Computer, Inc. BT-253 Bluetooth Adapter Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 002: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg trying to post dmesg exceeded the stackexchange posting limit of 30K... but nothing there is usb 3.0

  Read the article

• Joining on NULLs

  - by Dave Ballantyne

  A problem I see on a fairly regular basis is that of dealing with NULL values.  Specifically here, where we are joining two tables on two columns, one of which is ‘optional’ ie is nullable.  So something like this: i.e. Lookup where all the columns are equal, even when NULL.   NULL’s are a tricky thing to initially wrap your mind around.  Statements like “NULL is not equal to NULL and neither is it not not equal to NULL, it’s NULL” can cause a serious brain freeze and leave you a gibbering wreck and needing your mummy. Before we plod on, time to setup some data to demo against. Create table #SourceTable ( Id integer not null, SubId integer null, AnotherCol char(255) not null ) go create unique clustered index idxSourceTable on #SourceTable(id,subID) go with cteNums as ( select top(1000) number from master..spt_values where type ='P' ) insert into #SourceTable select Num1.number,nullif(Num2.number,0),'SomeJunk' from cteNums num1 cross join cteNums num2 go Create table #LookupTable ( Id integer not null, SubID integer null ) go insert into #LookupTable Select top(100) id,subid from #SourceTable where subid is not null order by newid() go insert into #LookupTable Select top(3) id,subid from #SourceTable where subid is null order by newid() If that has run correctly, you will have 1 million rows in #SourceTable and 103 rows in #LookupTable.  We now want to join one to the other. First attempt – Lets just join select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and #LookupTable.SubID = #SourceTable.SubID OK, that’s a fail.  We had 100 rows back,  we didn’t correctly account for the 3 rows that have null values.  Remember NULL <> NULL and the join clause specifies SUBID=SUBID, which for those rows is not true. Second attempt – Lets deal with those pesky NULLS select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and isnull(#LookupTable.SubID,0) = isnull(#SourceTable.SubID,0) OK, that’s the right result, well done and 99.9% of the time that is where its left. It is a relatively trivial CPU overhead to wrap ISNULL around both columns and compare that result, so no problems.  But, although that’s true, this a relational database we are using here, not a procedural language.  SQL is a declarative language, we are making a request to the engine to get the results we want.  How we ask for them can make a ton of difference. Lets look at the plan for our second attempt, specifically the clustered index seek on the #SourceTable   There are 2 predicates. The ‘seek predicate’ and ‘predicate’.  The ‘seek predicate’ describes how SQLServer has been able to use an Index.  Here, it has been able to navigate the index to resolve where ID=ID.  So far so good, but what about the ‘predicate’ (aka residual probe) ? This is a row-by-row operation.  For each row found in the index matching the Seek Predicate, the leaf level nodes have been scanned and tested using this logical condition.  In this example [Expr1007] is the result of the IsNull operation on #LookupTable and that is tested for equality with the IsNull operation on #SourceTable.  This residual probe is quite a high overhead, if we can express our statement slightly differently to take full advantage of the index and make the test part of the ‘Seek Predicate’. Third attempt – X is null and Y is null So, lets state the query in a slightly manner: select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and ( #LookupTable.SubID = #SourceTable.SubID or (#LookupTable.SubID is null and #SourceTable.SubId is null) ) So its slightly wordier and may not be as clear in its intent to the human reader, that is what comments are for, but the key point is that it is now clearer to the query optimizer what our intention is. Let look at the plan for that query, again specifically the index seek operation on #SourceTable No ‘predicate’, just a ‘Seek Predicate’ against the index to resolve both ID and SubID.  A subtle difference that can be easily overlooked.  But has it made a difference to the performance ? Well, yes , a perhaps surprisingly high one. Clever query optimizer well done. If you are using a scalar function on a column, you a pretty much guaranteeing that a residual probe will be used.  By re-wording the query you may well be able to avoid this and use the index completely to resolve lookups. In-terms of performance and scalability your system will be in a much better position if you can.

  Read the article

• Control HelpButton, HelpRequested, HelpButtonClicked - Instant help for windows Dialog Form components

  Instant help for windows dialog components is a great feature and very much known since windows 98. but I saw many many people are not aware it and query on Google to get help, but “help button” for dialogs helps you or your customers to get the help instantly. Every dialog window has help icon if that dialog was coded to enable it. it really helps to know the functionality of the components quickly. For example I was trying to pint a document from acrobat reader and opened printer properties to print the content front and back of the paper. If you observe there is a help button before close button. To get help on options of “Print on Both Sides” you would need to click on help button first and then click on the area on which you want to see the help. above picture shows help text for the options of “Print on Both Sides”. If you would like to get the help using keyboard you can use F1 key. Help button can be displayed only if minimize button and maximize button both are not shown unless you want go with custom buttons. below is the way if you want to get Help button for windows forms.   In this sample demo I want to have a checkbox and need to show help when I click on F1 on check box. So I created a form which country check box and help label as show in adjacent picture. Below is the code for your code bind file. using System; using System.Windows.Forms; namespace WindowsFormsApplication1 {     public partial classForm1: Form    {         publicForm1()         {             InitializeComponent();         }         private void Form1_Load(objectsender, EventArgs e)         {             this.Text = "Help Button Demo Form";             lblHelp.Text = "Press F1 on any component to get Instant Help";             this.HelpButton = true;             this.MaximizeBox = false;             this.MinimizeBox = false;             chkCountry.Tag = "Check or Uncheck Coutry Check Box";             chkCountry.HelpRequested += newHelpEventHandler(chkCountry_HelpRequested);             chkCountry.MouseLeave += newEventHandler(chkCountry_MouseLeave);         }         void chkCountry_HelpRequested(objectsender, HelpEventArgs hlpevent)         {             ControlrequestingControl = (Control)sender;             lblHelp.Text = (string)requestingControl.Tag;             hlpevent.Handled = true;         }         void chkCountry_MouseLeave(objectsender, EventArgs e)         {             lblHelp.Text = "Press F1 on any component to get Instant Help";         }     } } In above code  “HelpRequested” is an event will be fired when you click on F1 on Country checkbox. I stored the help information in the checkbox property called “Tag”. You might also maintain a property file to keep help text for each component differently. If you click on F1 when focus is on main form instead on individual component then generally separate help window opens. This can be done using the event “Form.HelpRequested” to open help windows as in below code. this.HelpRequested += newHelpEventHandler(Form1_HelpRequested); voidForm1_HelpRequested(objectsender, HelpEventArgs hlpevent) {     frmHelp.Show(); } span.fullpost {display:none;}

  Read the article

• EXTJS 3.2.1 EditorGridPanel - ComboBox with jsonstore

  - by Yoong Kim

  Hi, I am using EXTJS with an editorgridpanel and I am trying to to insert a combobox, populated with JsonStore. Here is a snapshot of my code: THE STORE: kmxgz.ordercmpappro.prototype.getCmpapproStore = function(my_url) { var myStore = new Ext.data.Store({ proxy: new Ext.data.HttpProxy({ url: my_url , method: 'POST' }) , reader: new Ext.data.JsonReader({ root: 'rows', totalProperty: 'total', id: 'list_cmpappro_id', fields: [ {name: 'list_cmpappro_id', mapping: 'list_cmpappro_id'} , {name: 'list_cmpappro_name', mapping: 'list_cmpappro_name'} ] }) , autoLoad: true , id: 'cmpapproStore' , listeners: { load: function(store, records, options){ //store is loaded, now you can work with it's records, etc. console.info('store load, arguments:', arguments); console.info('Store count = ', store.getCount()); } } }); return myStore; }; THE COMBO: kmxgz.ordercmpappro.prototype.getCmpapproCombo = function(my_store) { var myCombo = new Ext.form.ComboBox({ typeAhead: true, lazyRender:false, forceSelection: true, allowBlank: true, editable: true, selectOnFocus: true, id: 'cmpapproCombo', triggerAction: 'all', fieldLabel: 'CMP Appro', valueField: 'list_cmpappro_id', displayField: 'list_cmpappro_name', hiddenName: 'cmpappro_id', valueNotFoundText: 'Value not found.', mode: 'local', store: my_store, emptyText: 'Select a CMP Appro', loadingText: 'Veuillez patienter ...', listeners: { // 'change' will be fired when the value has changed and the user exits the ComboBox via tab, click, etc. // The 'newValue' and 'oldValue' params will be from the field specified in the 'valueField' config above. change: function(combo, newValue, oldValue){ console.log("Old Value: " + oldValue); console.log("New Value: " + newValue); }, // 'select' will be fired as soon as an item in the ComboBox is selected with mouse, keyboard. select: function(combo, record, index){ console.log(record.data.name); console.log(index); } } }); return myCombo; }; The combobox is inserted in an editorgridpanel. There's a renderer like this: Ext.util.Format.comboRenderer = function(combo){ return function(value, metadata, record){ alert(combo.store.getCount()); <== always 0!! var record = combo.findRecord(combo.valueField || combo.displayField, value); return record ? record.get(combo.displayField) : combo.valueNotFoundText; } }; When the grid is displayed the first time, instead of have the displayField, I have : "Value not found." And I have the alert : 0 (alert(combo.store.getCount())) from the renderer. But I can see in the console that the data have been correctly loaded! Even if I try to reload the store from the renderer (combo.store.load();), I still have the alert (0)! But when I select the combo to change the value, I can see the data and when I change the value, I can see the displayFiel! I don't understand what's the problem? Since now several days, I already tried all the solutions I found...but still nothing! Any advice is welcome! Yoong

  Read the article

• How can I do vertical paging with UITableView?

  - by vodkhang

  Let me describe the situation I am trying to do: I have a list of Items. When I go into ItemDetailView, which is a UITableView. I want to do paging here like: When I scroll down out of the table view, I want to display the next item. Like in Good Reader: Currently, I am trying 2 approaches but both do not really work for me. 1st: I let my UITableView over my scroll view and I have a nice animation and works quite ok except sometimes, the UITableView will receive event instead of my scroll view. And because, a UITableView is already a UITableView, this approach seems not be a good idea. Here is some code: - (void)applicationDidFinishLaunching:(UIApplication *)application { // a page is the width of the scroll view scrollView.pagingEnabled = YES; scrollView.contentSize = CGSizeMake(scrollView.frame.size.width, scrollView.frame.size.height * kNumberOfPages); scrollView.showsHorizontalScrollIndicator = NO; scrollView.showsVerticalScrollIndicator = YES; scrollView.scrollsToTop = NO; scrollView.delegate = self; [self loadScrollViewWithPage:0]; } - (void)loadScrollViewWithPage:(int)page { if (page < 0) return; if (page >= kNumberOfPages) return; [self.currentViewController.view removeFromSuperview]; self.currentViewController = [[[MyNewTableView alloc]initWithPageNumber:page] autorelease]; if (nil == currentViewController.view.superview) { CGRect frame = scrollView.frame; [scrollView addSubview:currentViewController.view]; } } - (void)scrollViewDidScroll:(UIScrollView *)sender { if (pageControlUsed) { return; } CGFloat pageHeight = scrollView.frame.size.height; int page = floor((scrollView.contentOffset.y - pageHeight / 2) / pageHeight) + 1; [self loadScrollViewWithPage:page]; } - (IBAction)changePage:(id)sender { int page = pageControl.currentPage; [self loadScrollViewWithPage:page]; // update the scroll view to the appropriate page CGRect frame = scrollView.frame; [scrollView scrollRectToVisible:frame animated:YES]; pageControlUsed = YES; } My second approach is: using pop and push of navigationController to pop the current ItemDetail and push a new one on top of it. But this approach will not give me a nice animation of scrolling down like the first approach. So, the answer to how I can get it done with either approach will be appreciated

  Read the article

• To connect Gstreamer with Qt in order to play a gstreamer video in the Qt Widget

  - by raggio

  I tried using phonon to play the video but could not succeed. Off-late came to know through the Qt forums that even the latest version of Qt does not support phonon. Thats when i started using Gstreamer.Any suggestions as to how to connect the Gstreamer window with the Qt widget?My aim is to play a video using Gstreamer on the Qt widget.So how do i link the gstreamer window and the Qt widget? I am successful in getting the Id of the widget through winid(). Further with the help of Gregory Pakosz, I have added the below 2 lines of code in my application - QApplication::syncX(); gst_x_overlay_set_xwindow_id(GST_X_OVERLAY(sink), widget->winId()); However am not able to link the Qt widget with the gstreamer video window. This is what my sample code would look like :- int main(int argc, char *argv[]) { printf("winid=%d\n", w.winId()); gst_init (NULL,NULL); /* create a new bin to hold the elements */ bin = gst_pipeline_new ("pipeline"); /* create a disk reader */ filesrc = gst_element_factory_make ("filesrc", "disk_source"); g_assert (filesrc); g_object_set (G_OBJECT (filesrc), "location", "PATH_TO_THE_EXECUTABLE", NULL); demux = gst_element_factory_make ("mpegtsdemux", "demuxer"); if (!demux) { g_print ("could not find plugin \"mpegtsmux\""); return -1; } vdecoder = gst_element_factory_make ("mpeg2dec", "decode"); if (!vdecoder) { g_print ("could not find plugin \"mpeg2dec\""); return -1; } videosink = gst_element_factory_make ("xvimagesink", "play_video"); g_assert (videosink); /* add objects to the main pipeline */ gst_bin_add_many (GST_BIN (bin), filesrc, demux, vdecoder, videosink, NULL); /* link the elements */ gst_element_link_many (filesrc, demux, vdecoder, videosink, NULL); gst_element_set_state(videosink, GST_STATE_READY); QApplication::syncX(); gst_x_overlay_set_xwindow_id(GST_X_OVERLAY(videosink), w.winId()); /* start playing */ gst_element_set_state (bin, GST_STATE_PLAYING); } Could you explain more in detail about the usage of gst_x_overlay_set_xwindow_id() wrt my context? Could i get any hint as to how i can integrate gstreamer under Qt? Please help me solve this problem

  Read the article

• 'NoneType' object has no attribute 'get' error using SQLAlchemy

  - by Az

  I've been trying to map an object to a database using SQLAlchemy but have run into a snag. Version info if handy: [OS: Mac OSX 10.5.8 | Python: 2.6.4 | SQLAlchemy: 0.5.8] The class I'm going to map: class Student(object): def __init__(self, name, id): self.id = id self.name = name self.preferences = collections.defaultdict(set) self.allocated_project = None self.allocated_rank = 0 def __repr__(self): return str(self) def __str__(self): return "%s %s" %(self.id, self.name) Background: Now, I've got a function that reads in the necessary information from a text database into these objects. The function more or less works and I can easily access the information from the objects. Before the SQLAlchemy code runs, the function will read in the necessary info and store it into the Class. There is a dictionary called students which stores this as such: students = {} students[id] = Student(<all the info from the various "reader" functions>) Afterwards, there is an "allocation" algorithm that will allocate projects to student. It does that well enough. The allocated_project remains as None if a student is unsuccessful in getting a project. SQLAlchemy bit: So after all this happens, I'd like to map my object to a database table. Using the documentation, I've used the following code to only map certain bits. I also begin to create a Session. from sqlalchemy import * from sqlalchemy.orm import * engine = create_engine('sqlite:///:memory:', echo=False) metadata = MetaData() students_table = Table('studs', metadata, Column('id', Integer, primary_key=True), Column('name', String) ) metadata.create_all(engine) mapper(Student, students_table) Session = sessionmaker(bind=engine) sesh = Session() Now after that, I was curious to see if I could print out all the students from my students dictionary. for student in students.itervalues(): print student What do I get but an error: Traceback (most recent call last): File "~/FYP_Tests/FYP_Tests.py", line 140, in <module> print student File "/~FYP_Tests/Parties.py", line 30, in __str__ return "%s %s" %(self.id, self.name) File "/opt/local/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/SQLAlchemy-0.5.8-py2.6.egg/sqlalchemy/orm/attributes.py", line 158, in __get__ return self.impl.get(instance_state(instance), instance_dict(instance)) AttributeError: 'NoneType' object has no attribute 'get' I'm at a loss as to how to resolve this issue, if it is an issue. If more information is required, please ask and I will provide it.

  Read the article

• Messing with Encoding and XslCompiledTransform

  - by Josemalive

  Hello, im messing with the encodings. For one hand i have a url that is responding me in UTF-8 (im pretty sure thanks to firebug plugin). Im opening the url reading the content in UTF-8 using the following code: StreamReader reader = new StreamReader(response.GetResponseStream(),System.Text.Encoding.UTF8); For other hand i have a transformation xslt sheet with the following code: <?xml version="1.0" encoding="utf-8"?> <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:msxsl="urn:schemas-microsoft-com:xslt" exclude-result-prefixes="msxsl"> <xsl:output method="xml" indent="yes"/> <xsl:template match="@* | node()"> <xsl:copy> <xsl:apply-templates select="@* | node()"/> <br/> hello </xsl:copy> </xsl:template> </xsl:stylesheet> This xslt sheet is saved in UTF-8 format too. I use the following code to mix the xml with the xslt: StringWriter writer = new StringWriter(); XslCompiledTransform transformer = new XslCompiledTransform(); transformer.Load(HttpContext.Current.Server.MapPath("xslt\\xsltsheet.xslt"); XmlWriterSettings xmlsettings = new XmlWriterSettings(); xmlsettings.Encoding = System.Text.Encoding.UTF8; transformer.Transform(xmlreader, null, writer); return writer; Then after all im render in the webbrowser the content of this writer and im getting the following error: The XML page cannot be displayed Cannot view XML input using style sheet. Please correct the error and then click the Refresh button, or try again later. Switch from current encoding to specified encoding not supported. Error processing resource 'http://localhost:2541/Results.... <?xml version="1.0" encoding="utf-16"?> Im wondering where is finding the UTF-16 encoding take in count that: All my files are saved as UTF-8 The response from the server is in UTF-8 The way of read the xslt sheet is configured as UTF-8. Any help would be appreciated. Thanks in advance. Best Regards. Jose.

  Read the article

• Something wrong with my XML?

  - by Prateek Raj

  hi everyone, i'm parsing an xml with my extjs but it returns only one of the five components. only the first one of the five components. Ext.regModel('Card', { fields: ['investor'] }); var store = new Ext.data.Store({ model: 'Card', proxy: { type: 'ajax', url: 'xmlformat.xml', reader: { type: 'xml', record: 'investors' } }, listeners: { single: true, datachanged: function(){ Ext.getBody().unmask(); var items = []; store.each(function(rec){ alert(rec.get('investor')); }); and my xml file is: <?xml version="1.0" encoding="UTF-8"?> <root> <investors> <investor>Active</investor> <investor>Aggressive</investor> <investor>Conservative</investor> <investor>Day Trader</investor> <investor>Very Active</investor> </investors> <events> <event>3 Month Expiry</event> <event>LEAPS</event> <event>Monthlies</event> <event>Monthly Expiries</event> <event>Weeklies</event> </events> <prices> <price>$0.5</price> <price>$0.05</price> <price>$1</price> <price>$22</price> <price>$100.34</price> </prices> </root> wen i run the code only "Active" comes out. . . . i know that i'm doing something wrong but i'm not sure what.... please help . . . . .

  Read the article

• Whats wrong with my triple DES wrapper??

  - by Chen Kinnrot

  it seems that my code adds 6 bytes to the result file after encrypt decrypt is called.. i tries it on a mkv file.. please help here is my code class TripleDESCryptoService : IEncryptor, IDecryptor { public void Encrypt(string inputFileName, string outputFileName, string key) { EncryptFile(inputFileName, outputFileName, key); } public void Decrypt(string inputFileName, string outputFileName, string key) { DecryptFile(inputFileName, outputFileName, key); } static void EncryptFile(string inputFileName, string outputFileName, string sKey) { var outFile = new FileStream(outputFileName, FileMode.OpenOrCreate, FileAccess.ReadWrite); // The chryptographic service provider we're going to use var cryptoAlgorithm = new TripleDESCryptoServiceProvider(); SetKeys(cryptoAlgorithm, sKey); // This object links data streams to cryptographic values var cryptoStream = new CryptoStream(outFile, cryptoAlgorithm.CreateEncryptor(), CryptoStreamMode.Write); // This stream writer will write the new file var encryptionStream = new BinaryWriter(cryptoStream); // This stream reader will read the file to encrypt var inFile = new FileStream(inputFileName, FileMode.Open, FileAccess.Read); var readwe = new BinaryReader(inFile); // Loop through the file to encrypt, line by line var date = readwe.ReadBytes((int)readwe.BaseStream.Length); // Write to the encryption stream encryptionStream.Write(date); // Wrap things up inFile.Close(); encryptionStream.Flush(); encryptionStream.Close(); } private static void SetKeys(SymmetricAlgorithm algorithm, string key) { var keyAsBytes = Encoding.ASCII.GetBytes(key); algorithm.IV = keyAsBytes.Take(algorithm.IV.Length).ToArray(); algorithm.Key = keyAsBytes.Take(algorithm.Key.Length).ToArray(); } static void DecryptFile(string inputFilename, string outputFilename, string sKey) { // The encrypted file var inFile = File.OpenRead(inputFilename); // The decrypted file var outFile = new FileStream(outputFilename, FileMode.OpenOrCreate, FileAccess.ReadWrite); // Prepare the encryption algorithm and read the key from the key file var cryptAlgorithm = new TripleDESCryptoServiceProvider(); SetKeys(cryptAlgorithm, sKey); // The cryptographic stream takes in the encrypted file var encryptionStream = new CryptoStream(inFile, cryptAlgorithm.CreateDecryptor(), CryptoStreamMode.Read); // Write the new unecrypted file var cleanStreamReader = new BinaryReader(encryptionStream); var cleanStreamWriter = new BinaryWriter(outFile); cleanStreamWriter.Write(cleanStreamReader.ReadBytes((int)inFile.Length)); cleanStreamWriter.Close(); outFile.Close(); cleanStreamReader.Close(); } }

  Read the article

• IE won't load PDF in a window created with window.open

  - by Dean

  Here's the problem, which only occurs in Internet Explorer (IE). I have a page that has links to several different types of files. Links from these files execute a Javascript function that opens a new window and loads the specific file. This works great, unless the file I need to open in the new window is a PDF in which case the window is blank, even though the URL is in the address field. Refreshing that window using F5 doesn't help. However, if I put the cursor in the address field and press <enter> the PDF loads right up. This problem only occurs in IE. I have seen it in IE 7 and 8 and am using Adobe Acrobat Reader 9. In Firefox (PC and Mac) everything works perfectly. In Chrome (Mac), the PDF is downloaded. In Safari (Mac) it works. In Opera (Mac) it prompts me to open or save. Basically, everything probably works fine, except for IE. I have searched for similar problems and have seen some posts where it was suggested to adjust some of the Internet Options on IE. I have tried this but it doesn't help, and the problem wasn't exactly the same anyway. Here's the Javascript function I use to open the new window. function newwin(url,w,h) { win = window.open(url,"temp","width="+w+",height="+h+",menubar=yes,toolbar=yes,location=yes,status=yes,scrollbars=auto,resizable=yes"); win.focus(); } You can see that I pass in the URL as well as the height, h, and width, w, of the window. I've used a function like this for years and as far as I know have never had a problem. I call the newwin() function using this. <a href="javascript:newwin('/path/document.pdf',400,300)">document.pdf</a> (Yes, I know there are other, better ways than using inline JS, and I've even tried some of them because I've run out of things to try, but nothing works.) So, if anyone has an idea as to what might be causing this problem, I'd love to hear it.

  Read the article

• Can MFMailComposeViewController attach an XML doc to an HTML message?

  - by Luther Baker

  I am creating an email in MFMaiilComposeViewController and if I simply create some html snippets and assign them to the message body - all is well. The resulting email (in GMail and Yahoo) looks like the original HTML I sent. [mailMan_ setMessageBody:body isHTML:YES]; On the other hand, if I also include an XML attachment, my email reader renders everything as plain text … including, the XML inlined. IE: my mail client (GMail, Yahoo) shows the raw HTHML and XML tags - including html tags that I didn't supply - ie: the html, head, body tags the iPhone provides around the content: NSData *opmlData = [[NSData alloc] initWithData:[opml dataUsingEncoding:NSUTF8StringEncoding]]; NSString *fileName = [NSString stringWithFormat:@"%f.opml", [NSDate timeIntervalSinceReferenceDate]]; [mailMan_ addAttachmentData:opmlData mimeType:@"text/xml" fileName:fileName]; I pop3'd the mails to see what was happening and found that WITHOUT an attachment, the resulting html section of the email contains this block: --0-1682099714-1273329398=:59784 Content-Type: text/html; charset=us-ascii <html><body bgcolor="#FFFFFF"><div><h2 style="b while on the other hand, WITH the XML attachment, the iPhone is sending this: --0-881105825-1273328091=:50337 Content-Type: text/plain; charset=us-ascii <html><body bgcolor="#FFFFFF"><div><h2 style="bac Notice the difference? Look at the Content-Type … text/html vs text/plain. It looks like when I include an XML attachment, the iPhone is errantly tagging the HTML version of the body as plain text! Just to clarify, technically, both with and without the attachment, the iPhone also includes this: --0-881105825-1273328091=:50337 Content-Type: text/plain; charset=us-ascii Notebook Carpentry Bathroom floor tile Bathroom wall tile Scrape thinset But this obviously isn't where the problem lies. Am I doing something wrong? What must I do to actually "attach" XML without the iPhone labeling the entire HTML body as plain text. I tried reversing the assignments (attachment first and then body) but no luck. For what it's worth, the email looks perfect from the iPhone's sending interface. Indeed, the HTML renders correctly and the attachment looks like a little icon at the bottom of the message. This problem has more to do with what the iPhone is actually sending.

  Read the article

• Adding Parsekit To An Xcode Project

  - by Garry

  I am trying to add the Parsekit framework to my OSX Xcode project. I've never added a 3rd party framework before and I can't get it to work right. I dragged the included Xcode project into my 'Groups & Files' pane and chose to Add it to my project. I then dragged Parsekit.framework underneath the Link Binary With Libraries heading. Then I double-clicked my target app and added Parsekit as a Direct Dependency. I also added libicucore.dylib as a Linked Library (as it says to do this on their site). Finally, in the Build settings tab of my target info I set the Header Search Paths to /Users/path/to/include/directory and the Other Linker Flags to -ObjC -all_load. Running this as a debug build work fine with no errors. However, when I build my app to release and then try to run the executable created, the app fails to load with the following error message: MyApp cannot be opened because of a problem. Check with the developer to make sure myApp works with this version of Mac OS X. Here is the dump from the crash reporter: Process: MyApp [11658] Path: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Identifier: com.yourcompany.MyApp Version: ??? (???) Code Type: X86-64 (Native) Parent Process: launchd [135] Date/Time: 2010-05-24 17:08:08.475 +0100 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6Interval Since Last Report: 133300 sec Crashes Since Last Report: 3 Per-App Crashes Since Last Report: 3 Anonymous UUID: DF0265E4-B5A0-45E1-8B71-D52A27CFDDCA Exception Type: EXC_BREAKPOINT (SIGTRAP) Exception Codes: 0x0000000000000002, 0x0000000000000000 Crashed Thread: 0 Dyld Error Message: Library not loaded: @executable_path/../Frameworks/ParseKit.framework/Versions/A/ParseKit Referenced from: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Reason: image not found Model: MacBookPro5,5, BootROM MBP55.00AC.B03, 2 processors, Intel Core 2 Duo, 2.53 GHz, 4 GB, SMC 1.47f2 Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB Memory Module: global_name AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.10.91.27) Bluetooth: Version 2.3.1f4, 2 service, 2 devices, 1 incoming serial ports Network Service: AirPort, AirPort, en1 Network Service: Ethernet Adaptor (en6), Ethernet, en6 Serial ATA Device: Hitachi HTS545025B9SA02, 232.89 GB Serial ATA Device: HL-DT-ST DVDRW GS23N USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0x24400000 USB Device: Internal Memory Card Reader, 0x05ac (Apple Inc.), 0x8403, 0x26500000 USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x04500000 USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0237, 0x04600000 USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8213, 0x06110000 After building the app, in addition to the executable file, Xcode is also creating a file called MyApp.app.dSYM. Any idea what that is?? I am developing with Xcode 3.2.2 on an Intel MBP running 10.6.3. Many thanks for any help offered.

  Read the article

• AVFoundation buffer comparison to a saved image

  - by user577552

  Hi, I am a long time reader, first time poster on StackOverflow, and must say it has been a great source of knowledge for me. I am trying to get to know the AVFoundation framework. What I want to do is save what the camera sees and then detect when something changes. Here is the part where I save the image to a UIImage : if (shouldSetBackgroundImage) { CGColorSpaceRef colorSpace = CGColorSpaceCreateDeviceRGB(); // Create a bitmap graphics context with the sample buffer data CGContextRef context = CGBitmapContextCreate(rowBase, bufferWidth, bufferHeight, 8, bytesPerRow, colorSpace, kCGBitmapByteOrder32Little | kCGImageAlphaPremultipliedFirst); // Create a Quartz image from the pixel data in the bitmap graphics context CGImageRef quartzImage = CGBitmapContextCreateImage(context); // Free up the context and color space CGContextRelease(context); CGColorSpaceRelease(colorSpace); // Create an image object from the Quartz image UIImage * image = [UIImage imageWithCGImage:quartzImage]; [self setBackgroundImage:image]; NSLog(@"reference image actually set"); // Release the Quartz image CGImageRelease(quartzImage); //Signal that the image has been saved shouldSetBackgroundImage = NO; } and here is the part where I check if there is any change in the image seen by the camera : else { CGImageRef cgImage = [backgroundImage CGImage]; CGDataProviderRef provider = CGImageGetDataProvider(cgImage); CFDataRef bitmapData = CGDataProviderCopyData(provider); char* data = CFDataGetBytePtr(bitmapData); if (data != NULL) { int64_t numDiffer = 0, pixelCount = 0; NSMutableArray * pointsMutable = [NSMutableArray array]; for( int row = 0; row < bufferHeight; row += 8 ) { for( int column = 0; column < bufferWidth; column += 8 ) { //we get one pixel from each source (buffer and saved image) unsigned char *pixel = rowBase + (row * bytesPerRow) + (column * BYTES_PER_PIXEL); unsigned char *referencePixel = data + (row * bytesPerRow) + (column * BYTES_PER_PIXEL); pixelCount++; if ( !match(pixel, referencePixel, matchThreshold) ) { numDiffer++; [pointsMutable addObject:[NSValue valueWithCGPoint:CGPointMake(SCREEN_WIDTH - (column/ (float) bufferHeight)* SCREEN_WIDTH - 4.0, (row/ (float) bufferWidth)* SCREEN_HEIGHT- 4.0)]]; } } } numberOfPixelsThatDiffer = numDiffer; points = [pointsMutable copy]; } For some reason, this doesn't work, meaning that the iPhone detects almost everything as being different from the saved image, even though I set a very low threshold for detection in the match function... Do you have any idea of what I am doing wrong?

  Read the article

• Odd ActiveRecord model dynamic initialization bug in production

  - by qfinder

  I've got an ActiveRecord (2.3.5) model that occasionally exhibits incorrect behavior that appears to be related to a problem in its dynamic initialization. Here's the code: class Widget < ActiveRecord::Base extend ActiveSupport::Memoizable serialize :settings VALID_SETTINGS = %w(show_on_sale show_upcoming show_current show_past) VALID_SETTINGS.each do |setting| class_eval %{ def #{setting}=(val); self.settings[:#{setting}] = (val == "1"); end def #{setting}; self.settings[:#{setting}]; end } end def initialize_settings self.settings ||= { :show_on_sale => true, :show_upcoming => true } end after_initialize :initialize_settings # All the other stuff the model does end The idea was to use a single record field (settings) to persist a bunch of configuration data for this object, but allow all the settings to seamlessly work with form helpers and the like. (Why this approach makes sense here is a little out of scope, but let's assume that it does.) Net-net, Widget should end up with instance methods (eg #show_on_sale= #show_on_sale) for all the entires in the VALID_SETTINGS array. Any default values should be specified in initialize_settings. And indeed this works, mostly. In dev and staging, no problems at all. But in production, the app sometimes ends up in a state where a) any writes to the dynamically generated setters fail and b) none of the default values appear to be set - although my leading theory is that the dynamically generated reader methods are just broken. The code, db, and environment is otherwise identical between the three. A typical error message / backtrace on the fail looks like: IndexError: index 141145 out of string (eval):2:in []=' (eval):2:inshow_on_sale=' [GEM_ROOT]/gems/activerecord-2.3.5/lib/active_record/base.rb:2746:in send' [GEM_ROOT]/gems/activerecord-2.3.5/lib/active_record/base.rb:2746:inattributes=' [GEM_ROOT]/gems/activerecord-2.3.5/lib/active_record/base.rb:2742:in each' [GEM_ROOT]/gems/activerecord-2.3.5/lib/active_record/base.rb:2742:inattributes=' [GEM_ROOT]/gems/activerecord-2.3.5/lib/active_record/base.rb:2634:in `update_attributes!' ...(then controller and all the way down) Ideas or theories as to what might be going on? My leading theory is that something is going wrong in instance initialization wherein the class instance variable settings is ending up as a string rather than a hash. This explains both the above setter failure (:show_on_sale is being used to index into the string) and the fact that getters don't work (an out of bounds [] call on a string just returns nil). But then how and why might settings occasionally end up as a string rather than hash?

  Read the article

• Write binary stream to browser using PHP

  - by Dave Jarvis

  Background Trying to stream a PDF report written using iReport through PHP to the browser. The general problem is: how do you write binary data to the browser using PHP? Working Code The following code does the job, but (for many reasons) it is not as efficient as it should be (the code writes a file then sends the file contents the browser). // Load the MySQL database driver. // java( 'java.lang.Class' )->forName( 'com.mysql.jdbc.Driver' ); // Attempt a database connection. // $conn = java( 'java.sql.DriverManager' )->getConnection( "jdbc:mysql://localhost:3306/climate?user=$user&password=$password" ); // Extract parameters. // $params = new java('java.util.HashMap'); $params->put('DistrictCode', '101'); $params->put('StationCode', '0066'); $params->put('CategoryCode', '010'); // Use the fill manager to produce the report. // $fm = java('net.sf.jasperreports.engine.JasperFillManager'); $pm = $fm->fillReport($report, $params, $conn); header('Cache-Control: no-cache private'); header('Content-Description: File Transfer'); header('Content-Disposition: attachment, filename=climate-report.pdf'); header('Content-Type: application/pdf'); header('Content-Transfer-Encoding: binary'); header('Content-Length: ' . strlen( $result ) ); $path = realpath( "." ) . "/output.pdf"; $em = java('net.sf.jasperreports.engine.JasperExportManager'); $result = $em->exportReportToPdfFile($pm,$path); readfile( $path ); $conn->close(); Non-working Code To remove the slight redundancy (i.e., write directly to the browser), the following code looks like it should work, but it does not: $em = java('net.sf.jasperreports.engine.JasperExportManager'); $result = $em->exportReportToPdf($pm); header('Content-Length: ' . strlen( $result ) ); echo $result; Content is sent to the browser, but the file is corrupt (it begins with the PDF header) and cannot be read by any PDF reader. Question How can I take out the middle step of writing to the file and write directly to the browser so that the PDF is not corrupted? Thank you!

  Read the article

• Blackberry Player, custom data source

  - by Alex

  Hello I must create a custom media player within the application with support for mp3 and wav files. I read in the documentation i cant seek or get the media file duration without a custom datasoruce. I checked the demo in the JDE 4.6 but i have still problems... I cant get the duration, it return much more then the expected so i`m sure i screwed up something while i modified the code to read the mp3 file locally from the filesystem. Somebody can help me what i did wrong ? (I can hear the mp3, so the player plays it correctly from start to end) I must support OSs = 4.6. Thank You Here is my modified datasource LimitedRateStreaminSource.java * Copyright © 1998-2009 Research In Motion Ltd. Note: For the sake of simplicity, this sample application may not leverage resource bundles and resource strings. However, it is STRONGLY recommended that application developers make use of the localization features available within the BlackBerry development platform to ensure a seamless application experience across a variety of languages and geographies. For more information on localizing your application, please refer to the BlackBerry Java Development Environment Development Guide associated with this release. */ package com.halcyon.tawkwidget.model; import java.io.IOException; import java.io.InputStream; import java.io.OutputStream; import javax.microedition.io.Connector; import javax.microedition.io.file.FileConnection; import javax.microedition.media.Control; import javax.microedition.media.protocol.ContentDescriptor; import javax.microedition.media.protocol.DataSource; import javax.microedition.media.protocol.SourceStream; import net.rim.device.api.io.SharedInputStream; /** * The data source used by the BufferedPlayback's media player. / public final class LimitedRateStreamingSource extends DataSource { /* The max size to be read from the stream at one time. */ private static final int READ_CHUNK = 512; // bytes /** A reference to the field which displays the load status. */ //private TextField _loadStatusField; /** A reference to the field which displays the player status. */ //private TextField _playStatusField; /** * The minimum number of bytes that must be buffered before the media file * will begin playing. */ private int _startBuffer = 200000; /** The maximum size (in bytes) of a single read. */ private int _readLimit = 32000; /** * The minimum forward byte buffer which must be maintained in order for * the video to keep playing. If the forward buffer falls below this * number, the playback will pause until the buffer increases. */ private int _pauseBytes = 64000; /** * The minimum forward byte buffer required to resume * playback after a pause. */ private int _resumeBytes = 128000; /** The stream connection over which media content is passed. */ //private ContentConnection _contentConnection; private FileConnection _fileConnection; /** An input stream shared between several readers. */ private SharedInputStream _readAhead; /** A stream to the buffered resource. */ private LimitedRateSourceStream _feedToPlayer; /** The MIME type of the remote media file. */ private String _forcedContentType; /** A counter for the total number of buffered bytes */ private volatile int _totalRead; /** A flag used to tell the connection thread to stop */ private volatile boolean _stop; /** * A flag used to indicate that the initial buffering is complete. In * other words, that the current buffer is larger than the defined start * buffer size. */ private volatile boolean _bufferingComplete; /** A flag used to indicate that the remote file download is complete. */ private volatile boolean _downloadComplete; /** The thread which retrieves the remote media file. */ private ConnectionThread _loaderThread; /** The local save file into which the remote file is written. */ private FileConnection _saveFile; /** A stream for the local save file. */ private OutputStream _saveStream; /** * Constructor. * @param locator The locator that describes the DataSource. */ public LimitedRateStreamingSource(String locator) { super(locator); } /** * Open a connection to the locator. * @throws IOException */ public void connect() throws IOException { //Open the connection to the remote file. _fileConnection = (FileConnection)Connector.open(getLocator(), Connector.READ); //Cache a reference to the locator. String locator = getLocator(); //Report status. System.out.println("Loading: " + locator); //System.out.println("Size: " + _contentConnection.getLength()); System.out.println("Size: " + _fileConnection.totalSize()); //The name of the remote file begins after the last forward slash. int filenameStart = locator.lastIndexOf('/'); //The file name ends at the first instance of a semicolon. int paramStart = locator.indexOf(';'); //If there is no semicolon, the file name ends at the end of the line. if (paramStart < 0) { paramStart = locator.length(); } //Extract the file name. String filename = locator.substring(filenameStart, paramStart); System.out.println("Filename: " + filename); //Open a local save file with the same name as the remote file. _saveFile = (FileConnection) Connector.open("file:///SDCard/blackberry/music" + filename, Connector.READ_WRITE); //If the file doesn't already exist, create it. if (!_saveFile.exists()) { _saveFile.create(); } System.out.println("---------- 1"); //Open the file for writing. _saveFile.setReadable(true); //Open a shared input stream to the local save file to //allow many simultaneous readers. SharedInputStream fileStream = SharedInputStream.getSharedInputStream(_saveFile.openInputStream()); //Begin reading at the beginning of the file. fileStream.setCurrentPosition(0); System.out.println("---------- 2"); //If the local file is smaller than the remote file... if (_saveFile.fileSize() < _fileConnection.totalSize()) { System.out.println("---------- 3"); //Did not get the entire file, set the system to try again. _saveFile.setWritable(true); System.out.println("---------- 4"); //A non-null save stream is used as a flag later to indicate that //the file download was incomplete. _saveStream = _saveFile.openOutputStream(); System.out.println("---------- 5"); //Use a new shared input stream for buffered reading. _readAhead = SharedInputStream.getSharedInputStream(_fileConnection.openInputStream()); System.out.println("---------- 6"); } else { //The download is complete. System.out.println("---------- 7"); _downloadComplete = true; //We can use the initial input stream to read the buffered media. _readAhead = fileStream; System.out.println("---------- 8"); //We can close the remote connection. _fileConnection.close(); System.out.println("---------- 9"); } if (_forcedContentType != null) { //Use the user-defined content type if it is set. System.out.println("---------- 10"); _feedToPlayer = new LimitedRateSourceStream(_readAhead, _forcedContentType); System.out.println("---------- 11"); } else { System.out.println("---------- 12"); //Otherwise, use the MIME types of the remote file. // _feedToPlayer = new LimitedRateSourceStream(_readAhead, _fileConnection)); } System.out.println("---------- 13"); } /** * Destroy and close all existing connections. */ public void disconnect() { try { if (_saveStream != null) { //Destroy the stream to the local save file. _saveStream.close(); _saveStream = null; } //Close the local save file. _saveFile.close(); if (_readAhead != null) { //Close the reader stream. _readAhead.close(); _readAhead = null; } //Close the remote file connection. _fileConnection.close(); //Close the stream to the player. _feedToPlayer.close(); } catch (Exception e) { System.err.println(e.getMessage()); } } /** * Returns the content type of the remote file. * @return The content type of the remote file. */ public String getContentType() { return _feedToPlayer.getContentDescriptor().getContentType(); } /** * Returns a stream to the buffered resource. * @return A stream to the buffered resource. */ public SourceStream[] getStreams() { return new SourceStream[] { _feedToPlayer }; } /** * Starts the connection thread used to download the remote file. */ public void start() throws IOException { //If the save stream is null, we have already completely downloaded //the file. if (_saveStream != null) { //Open the connection thread to finish downloading the file. _loaderThread = new ConnectionThread(); _loaderThread.start(); } } /** * Stop the connection thread. */ public void stop() throws IOException { //Set the boolean flag to stop the thread. _stop = true; } /** * @see javax.microedition.media.Controllable#getControl(String) */ public Control getControl(String controlType) { // No implemented Controls. return null; } /** * @see javax.microedition.media.Controllable#getControls() */ public Control[] getControls() { // No implemented Controls. return null; } /** * Force the lower level stream to a given content type. Must be called * before the connect function in order to work. * @param contentType The content type to use. */ public void setContentType(String contentType) { _forcedContentType = contentType; } /** * A stream to the buffered media resource. */ private final class LimitedRateSourceStream implements SourceStream { /** A stream to the local copy of the remote resource. */ private SharedInputStream _baseSharedStream; /** Describes the content type of the media file. */ private ContentDescriptor _contentDescriptor; /** * Constructor. Creates a LimitedRateSourceStream from * the given InputStream. * @param inputStream The input stream used to create a new reader. * @param contentType The content type of the remote file. */ LimitedRateSourceStream(InputStream inputStream, String contentType) { System.out.println("[LimitedRateSoruceStream]---------- 1"); _baseSharedStream = SharedInputStream.getSharedInputStream(inputStream); System.out.println("[LimitedRateSoruceStream]---------- 2"); _contentDescriptor = new ContentDescriptor(contentType); System.out.println("[LimitedRateSoruceStream]---------- 3"); } /** * Returns the content descriptor for this stream. * @return The content descriptor for this stream. */ public ContentDescriptor getContentDescriptor() { return _contentDescriptor; } /** * Returns the length provided by the connection. * @return long The length provided by the connection. */ public long getContentLength() { return _fileConnection.totalSize(); } /** * Returns the seek type of the stream. */ public int getSeekType() { return RANDOM_ACCESSIBLE; //return SEEKABLE_TO_START; } /** * Returns the maximum size (in bytes) of a single read. */ public int getTransferSize() { return _readLimit; } /** * Writes bytes from the buffer into a byte array for playback. * @param bytes The buffer into which the data is read. * @param off The start offset in array b at which the data is written. * @param len The maximum number of bytes to read. * @return the total number of bytes read into the buffer, or -1 if * there is no more data because the end of the stream has been reached. * @throws IOException */ public int read(byte[] bytes, int off, int len) throws IOException { System.out.println("[LimitedRateSoruceStream]---------- 5"); System.out.println("Read Request for: " + len + " bytes"); //Limit bytes read to our readLimit. int readLength = len; System.out.println("[LimitedRateSoruceStream]---------- 6"); if (readLength > getReadLimit()) { readLength = getReadLimit(); } //The number of available byes in the buffer. int available; //A boolean flag indicating that the thread should pause //until the buffer has increased sufficiently. boolean paused = false; System.out.println("[LimitedRateSoruceStream]---------- 7"); for (;;) { available = _baseSharedStream.available(); System.out.println("[LimitedRateSoruceStream]---------- 8"); if (_downloadComplete) { //Ignore all restrictions if downloading is complete. System.out.println("Complete, Reading: " + len + " - Available: " + available); return _baseSharedStream.read(bytes, off, len); } else if(_bufferingComplete) { if (paused && available > getResumeBytes()) { //If the video is paused due to buffering, but the //number of available byes is sufficiently high, //resume playback of the media. System.out.println("Resuming - Available: " + available); paused = false; return _baseSharedStream.read(bytes, off, readLength); } else if(!paused && (available > getPauseBytes() || available > readLength)) { //We have enough information for this media playback. if (available < getPauseBytes()) { //If the buffer is now insufficient, set the //pause flag. paused = true; } System.out.println("Reading: " + readLength + " - Available: " + available); return _baseSharedStream.read(bytes, off, readLength); } else if(!paused) { //Set pause until loaded enough to resume. paused = true; } } else { //We are not ready to start yet, try sleeping to allow the //buffer to increase. try { Thread.sleep(500); } catch (Exception e) { System.err.println(e.getMessage()); } } } } /** * @see javax.microedition.media.protocol.SourceStream#seek(long) */ public long seek(long where) throws IOException { _baseSharedStream.setCurrentPosition((int) where); return _baseSharedStream.getCurrentPosition(); } /** * @see javax.microedition.media.protocol.SourceStream#tell() */ public long tell() { return _baseSharedStream.getCurrentPosition(); } /** * Close the stream. * @throws IOException */ void close() throws IOException { _baseSharedStream.close(); } /** * @see javax.microedition.media.Controllable#getControl(String) */ public Control getControl(String controlType) { // No implemented controls. return null; } /** * @see javax.microedition.media.Controllable#getControls() */ public Control[] getControls() { // No implemented controls. return null; } } /** * A thread which downloads the remote file and writes it to the local file. */ private final class ConnectionThread extends Thread { /** * Download the remote media file, then write it to the local * file. * @see java.lang.Thread#run() */ public void run() { try { byte[] data = new byte[READ_CHUNK]; int len = 0; //Until we reach the end of the file. while (-1 != (len = _readAhead.read(data))) { _totalRead += len; if (!_bufferingComplete && _totalRead > getStartBuffer()) { //We have enough of a buffer to begin playback. _bufferingComplete = true; System.out.println("Initial Buffering Complete"); } if (_stop) { //Stop reading. return; } } System.out.println("Downloading Complete"); System.out.println("Total Read: " + _totalRead); //If the downloaded data is not the same size //as the remote file, something is wrong. if (_totalRead != _fileConnection.totalSize()) { System.err.println("* Unable to Download entire file *"); } _downloadComplete = true; _readAhead.setCurrentPosition(0); //Write downloaded data to the local file. while (-1 != (len = _readAhead.read(data))) { _saveStream.write(data); } } catch (Exception e) { System.err.println(e.toString()); } } } /** * Gets the minimum forward byte buffer which must be maintained in * order for the video to keep playing. * @return The pause byte buffer. */ int getPauseBytes() { return _pauseBytes; } /** * Sets the minimum forward buffer which must be maintained in order * for the video to keep playing. * @param pauseBytes The new pause byte buffer. */ void setPauseBytes(int pauseBytes) { _pauseBytes = pauseBytes; } /** * Gets the maximum size (in bytes) of a single read. * @return The maximum size (in bytes) of a single read. */ int getReadLimit() { return _readLimit; } /** * Sets the maximum size (in bytes) of a single read. * @param readLimit The new maximum size (in bytes) of a single read. */ void setReadLimit(int readLimit) { _readLimit = readLimit; } /** * Gets the minimum forward byte buffer required to resume * playback after a pause. * @return The resume byte buffer. */ int getResumeBytes() { return _resumeBytes; } /** * Sets the minimum forward byte buffer required to resume * playback after a pause. * @param resumeBytes The new resume byte buffer. */ void setResumeBytes(int resumeBytes) { _resumeBytes = resumeBytes; } /** * Gets the minimum number of bytes that must be buffered before the * media file will begin playing. * @return The start byte buffer. */ int getStartBuffer() { return _startBuffer; } /** * Sets the minimum number of bytes that must be buffered before the * media file will begin playing. * @param startBuffer The new start byte buffer. */ void setStartBuffer(int startBuffer) { _startBuffer = startBuffer; } } And in this way i use it: LimitedRateStreamingSource source = new LimitedRateStreamingSource("file:///SDCard/music3.mp3"); source.setContentType("audio/mpeg"); mediaPlayer = javax.microedition.media.Manager.createPlayer(source); mediaPlayer.addPlayerListener(this); mediaPlayer.realize(); mediaPlayer.prefetch(); After start i use mediaPlayer.getDuration it returns lets say around 24:22 (the inbuild media player in the blackberry say the file length is 4:05) I tried to get the duration in the listener and there unfortunatly returned around 64 minutes, so im sure something is not good inside the datasoruce....

  Read the article

• OperationalError: foreign key mismatch

  - by Niek de Klein

  I have two tables that I'm filling, 'msrun' and 'feature'. 'feature' has a foreign key pointing to the 'msrun_name' column of the 'msrun' table. Inserting in the tables works fine. But when I try to delete from the 'feature' table I get the following error: pysqlite2.dbapi2.OperationalError: foreign key mismatch From the rules of foreign keys in the manual of SQLite: - The parent table does not exist, or - The parent key columns named in the foreign key constraint do not exist, or - The parent key columns named in the foreign key constraint are not the primary key of the parent table and are not subject to a unique constraint using collating sequence specified in the CREATE TABLE, or - The child table references the primary key of the parent without specifying the primary key columns and the number of primary key columns in the parent do not match the number of child key columns. I can see nothing that I'm violating. My create tables look like this: DROP TABLE IF EXISTS `msrun`; -- ----------------------------------------------------- -- Table `msrun` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `msrun` ( `msrun_name` VARCHAR(40) PRIMARY KEY NOT NULL , `description` VARCHAR(500) NOT NULL ); DROP TABLE IF EXISTS `feature`; -- ----------------------------------------------------- -- Table `feature` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `feature` ( `feature_id` VARCHAR(40) PRIMARY KEY NOT NULL , `intensity` DOUBLE NOT NULL , `overallquality` DOUBLE NOT NULL , `charge` INT NOT NULL , `content` VARCHAR(45) NOT NULL , `msrun_msrun_name` VARCHAR(40) NOT NULL , CONSTRAINT `fk_feature_msrun1` FOREIGN KEY (`msrun_msrun_name` ) REFERENCES `msrun` (`msrun_name` ) ON DELETE NO ACTION ON UPDATE NO ACTION); CREATE UNIQUE INDEX `id_UNIQUE` ON `feature` (`feature_id` ASC); CREATE INDEX `fk_feature_msrun1` ON `feature` (`msrun_msrun_name` ASC); As far as I can see the parent table exists, the foreign key is pointing to the right parent key, the parent key is a primary key and the foreign key specifies the primary key column. The script that produces the error: from pysqlite2 import dbapi2 as sqlite import parseFeatureXML connection = sqlite.connect('example.db') cursor = connection.cursor() cursor.execute("PRAGMA foreign_keys=ON") inputValues = ('example', 'description') cursor.execute("INSERT INTO `msrun` VALUES(?, ?)", inputValues) featureXML = parseFeatureXML.Reader('../example_scripts/example_files/input/featureXML_example.featureXML') for feature in featureXML.getSimpleFeatureInfo(): inputValues = (featureXML['id'], featureXML['intensity'], featureXML['overallquality'], featureXML['charge'], featureXML['content'], 'example') # insert the values into msrun using ? for sql injection safety cursor.execute("INSERT INTO `feature` VALUES(?,?,?,?,?,?)", inputValues) connection.commit() for feature in featureXML.getSimpleFeatureInfo(): cursor.execute("DELETE FROM `feature` WHERE feature_id = ?", (str(featureXML['id']),))

  Read the article

• Bidirectional FIFO

  - by nunos

  I would like to implement a bidirectional fifo. The code below is functioning but it is not using bidirectional fifo. I have searched all over the internet, but haven't found any good example... How can I do that? Thanks, WRITER.c: #include <stdio.h> #include <unistd.h> #include <string.h> #include <sys/types.h> #include <sys/wait.h> #include <fcntl.h> #define MAXLINE 4096 #define READ 0 #define WRITE 1 int main (int argc, char** argv) { int a, b, fd; do { fd=open("/tmp/myfifo",O_WRONLY); if (fd==-1) sleep(1); } while (fd==-1); while (1) { scanf("%d", &a); scanf("%d", &b); write(fd,&a,sizeof(int)); write(fd,&b,sizeof(int)); if (a == 0 && b == 0) { break; } } close(fd); return 0; } READER.c: #include <stdio.h> #include <unistd.h> #include <string.h> #include <sys/types.h> #include <sys/wait.h> #include <fcntl.h> #include <sys/stat.h> #define MAXLINE 4096 #define READ 0 #define WRITE 1 int main(void) { int n1, n2; int fd; mkfifo("/tmp/myfifo",0660); fd=open("/tmp/myfifo",O_RDONLY); while(read(fd, &n1, sizeof(int) )) { read(fd, &n2, sizeof(int)); if (n1 == 0 && n2 == 0) { break; } printf("soma: %d\n",n1+n2); printf("diferenca: %d\n", n1-n2); printf("divisao: %f\n", n1/(double)n2); printf("multiplicacao: %d\n", n1*n2); } close(fd); return 0; }

  Read the article

• Java: Reading a pdf file from URL into Byte array/ByteBuffer in an applet.

  - by Pol

  I'm trying to figure out why this particular snippet of code isn't working for me. I've got an applet which is supposed to read a .pdf and display it with a pdf-renderer library, but for some reason when I read in the .pdf files which sit on my server, they end up as being corrupt. I've tested it by writing the files back out again. I've tried viewing the applet in both IE and Firefox and the corrupt files occur. Funny thing is, when I trying viewing the applet in Safari (for Windows), the file is actually fine! I understand the JVM might be different, but I am still lost. I've compiled in Java 1.5. JVMs are 1.6. The snippet which reads the file is below. public static ByteBuffer getAsByteArray(URL url) throws IOException { ByteArrayOutputStream tmpOut = new ByteArrayOutputStream(); URLConnection connection = url.openConnection(); int contentLength = connection.getContentLength(); InputStream in = url.openStream(); byte[] buf = new byte[512]; int len; while (true) { len = in.read(buf); if (len == -1) { break; } tmpOut.write(buf, 0, len); } tmpOut.close(); ByteBuffer bb = ByteBuffer.wrap(tmpOut.toByteArray(), 0, tmpOut.size()); //Lines below used to test if file is corrupt //FileOutputStream fos = new FileOutputStream("C:\\abc.pdf"); //fos.write(tmpOut.toByteArray()); return bb; } I must be missing something, and I've been banging my head trying to figure it out. Any help is greatly appreciated. Thanks. Edit: To further clarify my situation, the difference in the file before I read then with the snippet and after, is that the ones I output after reading are significantly smaller than they originally are. When opening them, they are not recognized as .pdf files. There are no exceptions being thrown that I ignore, and I have tried flushing to no avail. This snippet works in Safari, meaning the files are read in it's entirety, with no difference in size, and can be opened with any .pdf reader. In IE and Firefox, the files always end up being corrupted, consistently the same smaller size. I monitored the len variable (when reading a 59kb file), hoping to see how many bytes get read in at each loop. In IE and Firefox, at 18kb, the in.read(buf) returns a -1 as if the file has ended. Safari does not do this. I'll keep at it, and I appreciate all the suggestions so far.

  Read the article

• Problem with type coercion and string concatenation in JavaScript in Greasemonkey script on Firefox

  - by Yi Jiang

  I'm creating a GreaseMonkey script to improve the user interface of the 10k tools Stack Overflow uses. I have encountered an unreproducible and frankly bizarre problem that has confounded me and the others in the JavaScript room on SO Chat. We have yet to find the cause after several lengthy debugging sessions. The problematic script can be found here. Source - Install The problem occurs at line 85, the line after the 'vodoo' comment: return (t + ' (' + +(+f.offensive + +f.spam) + ')'); It might look a little weird, but the + in front of the two variables and the inner bracket is for type coercion, the inner middle + is for addition, and the other ones are for concatenation. Nothing special, but observant reader might note that type coercion on the inner bracket is unnecessary, since both are already type coerced to numbers, and type coercing result is useless when they get concatenated into a string anyway. Not so! Removing the + breaks the script, causing f.offensive and f.spam to be concatenated instead of added together. Adding further console.log only makes things more confusing: console.log(f.offensive + f.spam); // 50 console.log('' + (+f.offensive + +f.spam)); // 5, but returning this yields 50 somehow console.log('' + (+f.offensive + +f.spam) + ''); // 50 Source: http://chat.stackoverflow.com/transcript/message/203261#203261 The problem is that this is unreproducible - running scripts like console.log('a' + (+'3' + +'1') + 'b'); in the Firebug console yields the correct result, as does (function(){ return 'a' + (+'3' + +'1') + 'b'; })(); Even pulling out large chunks of the code and running them in the console does not reproduce this bug: $('.post-menu a[id^=flag-post-]').each(function(){ var f = {offensive: '4', spam: '1'}; if(f){ $(this).text(function(i, t){ // Vodoo - please do not remove the '+' in front of the inner bracket return (t + ' (' + +(+f.offensive + +f.spam) + ')'); }); } }); Tim Stone in the chatroom has reproduction instruction for those who are below 10k. This bug only appears in Firefox - Chrome does not appear to exhibit this problem, leading me to believe that this may be a problem with either Firefox's JavaScript engine, or the Greasemonkey add-on. Am I right? I can be found in the JavaScript room if you want more detail and/or want to discuss this.

  Read the article

• how to debug "deep" crashes in Android?

  - by eerok512

  Hi All, I've been trying to debug an android crash that is occurring without a Java Stack Trace... Java Stack Trace bugs are very easy for me to fix... but this bug I'm getting seems to be crashing inside the "NDK" or whatever it is the deep internals of Android are called... I've made no modifications to the NDK btw... I just dunno what else to call that layer hehe. Anyway I'm mainly looking for advice on deep-debug methods, rather than help with this specific problem... because I doubt I can post all the source code involved... so really I just need to know how to set breakpoints at the deep layers or whatever other methods there are to trace deep-crashes to their source... so I will briefly describe the bug and then post a LogCat. I have an app with 7 Activities Activity_INTRO Activity_EULA Activity_MAIN Activity_Contact Activity_News Activity_Library Activity_More INTRO is the initiating one... it fades in some company logos... after displaying them for a set time it jumps to the EULA activity... after the user accepts the EULA, it jumps to MAIN... MAIN then creates a TabHost and populates it with the 4 remaining activities now heres the thing... when I click on say, the More tab of the TabHost, the app pauses for a few seconds and then hard-crashes... no java stack trace, but an actual ASM level trace with the registers and IP and stack... the same thing occurs no matter which tab I select, Contact, News, Library, More... all of them crash with the same hard-crash if however I set the manifest to start the app at Activity_MAIN, bypassing the INTRO and EULA, then these crashes do not occur... so something is lingering from those opening activities that is somehow hosing the TabHost'ed Activities... and I'm wondering what the hell that could be... because I'm using finish() on those activites when they need to jump... in fact here is how I'm doing it let me know if you see any bugs: when jumping from INTRO to EULA I do: //Display the EULA Intent newIntent = new Intent (avi, Activity_EULA.class); startActivity (newIntent); finish(); and EULA to MAIN: Intent newIntent = new Intent (this, Activity_Main.class); startActivity (newIntent); finish(); anyway, here is the hard crash log... please let me know if there is some way I can reverse engineer either /system/lib/libcutils.so or /system/lib/libandroid_runtime.so, because I think the crash is happening in one of them... i think its happening in the libandroid_runtime in fact.... anyway on to the log: 12-25 00:56:07.322: INFO/DEBUG(551): *** *** *** *** *** *** *** *** *** *** *** *** *** *** *** *** 12-25 00:56:07.332: INFO/DEBUG(551): Build fingerprint: 'generic/sdk/generic/:1.5/CUPCAKE/150240:eng/test-keys' 12-25 00:56:07.362: INFO/DEBUG(551): pid: 722, tid: 723 >>> com.killerapps.chokes <<< 12-25 00:56:07.362: INFO/DEBUG(551): signal 11 (SIGSEGV), fault addr 00000004 12-25 00:56:07.362: INFO/DEBUG(551): r0 00000004 r1 40021800 r2 00000004 r3 ad3296c5 12-25 00:56:07.372: INFO/DEBUG(551): r4 00000000 r5 00000000 r6 ad342da5 r7 41039fb8 12-25 00:56:07.372: INFO/DEBUG(551): r8 100ffcb0 r9 41039fb0 10 41e014a0 fp 00001071 12-25 00:56:07.382: INFO/DEBUG(551): ip ad35b874 sp 100ffc98 lr ad3296cf pc afb045a8 cpsr 00000010 12-25 00:56:07.552: INFO/DEBUG(551): #00 pc 000045a8 /system/lib/libcutils.so 12-25 00:56:07.572: INFO/DEBUG(551): #01 lr ad3296cf /system/lib/libandroid_runtime.so 12-25 00:56:07.582: INFO/DEBUG(551): stack: 12-25 00:56:07.582: INFO/DEBUG(551): 100ffc58 00000000 12-25 00:56:07.592: INFO/DEBUG(551): 100ffc5c 001c5278 [heap] 12-25 00:56:07.602: INFO/DEBUG(551): 100ffc60 000000da 12-25 00:56:07.602: INFO/DEBUG(551): 100ffc64 0016c778 [heap] 12-25 00:56:07.602: INFO/DEBUG(551): 100ffc68 100ffcc8 12-25 00:56:07.602: INFO/DEBUG(551): 100ffc6c 001c5278 [heap] 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc70 427d1ac0 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc74 000000c1 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc78 40021800 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc7c 000000c2 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc80 00000000 12-25 00:56:07.612: INFO/DEBUG(551): 100ffc84 00000000 12-25 00:56:07.622: INFO/DEBUG(551): 100ffc88 00000000 12-25 00:56:07.622: INFO/DEBUG(551): 100ffc8c 00000000 12-25 00:56:07.622: INFO/DEBUG(551): 100ffc90 df002777 12-25 00:56:07.632: INFO/DEBUG(551): 100ffc94 e3a070ad 12-25 00:56:07.632: INFO/DEBUG(551): #00 100ffc98 00000000 12-25 00:56:07.632: INFO/DEBUG(551): 100ffc9c ad3296cf /system/lib/libandroid_runtime.so 12-25 00:56:07.632: INFO/DEBUG(551): 100ffca0 100ffcd0 12-25 00:56:07.642: INFO/DEBUG(551): 100ffca4 ad342db5 /system/lib/libandroid_runtime.so 12-25 00:56:07.642: INFO/DEBUG(551): 100ffca8 410a79d0 12-25 00:56:07.642: INFO/DEBUG(551): 100ffcac ad00e3b8 /system/lib/libdvm.so 12-25 00:56:07.652: INFO/DEBUG(551): 100ffcb0 410a79d0 12-25 00:56:07.652: INFO/DEBUG(551): 100ffcb4 0016bac0 [heap] 12-25 00:56:07.662: INFO/DEBUG(551): 100ffcb8 ad342da5 /system/lib/libandroid_runtime.so 12-25 00:56:07.662: INFO/DEBUG(551): 100ffcbc 40021800 12-25 00:56:07.662: INFO/DEBUG(551): 100ffcc0 410a79d0 12-25 00:56:07.662: INFO/DEBUG(551): 100ffcc4 afe39dd0 12-25 00:56:07.662: INFO/DEBUG(551): 100ffcc8 100ffcd0 12-25 00:56:07.662: INFO/DEBUG(551): 100ffccc ad040a8d /system/lib/libdvm.so 12-25 00:56:07.672: INFO/DEBUG(551): 100ffcd0 41039fb0 12-25 00:56:07.672: INFO/DEBUG(551): 100ffcd4 420000f8 12-25 00:56:07.672: INFO/DEBUG(551): 100ffcd8 ad342da5 /system/lib/libandroid_runtime.so 12-25 00:56:07.672: INFO/DEBUG(551): 100ffcdc 100ffd48 12-25 00:56:07.852: DEBUG/dalvikvm(722): GC freed 367 objects / 15144 bytes in 210ms 12-25 00:56:08.081: DEBUG/InetAddress(722): www.akillerapp.com: 74.86.47.202 (family 2, proto 6) 12-25 00:56:08.242: DEBUG/dalvikvm(722): GC freed 62 objects / 2328 bytes in 122ms 12-25 00:56:08.771: DEBUG/dalvikvm(722): GC freed 245 objects / 11744 bytes in 179ms 12-25 00:56:09.131: INFO/ActivityManager(577): Process com.killerapps.chokes (pid 722) has died. 12-25 00:56:09.171: INFO/WindowManager(577): WIN DEATH: Window{43719320 com.killerapps.chokes/com.killerapps.chokes.Activity_Main paused=false} 12-25 00:56:09.251: INFO/DEBUG(551): debuggerd committing suicide to free the zombie! 12-25 00:56:09.291: DEBUG/Zygote(553): Process 722 terminated by signal (11) 12-25 00:56:09.311: INFO/DEBUG(781): debuggerd: Jun 30 2009 17:00:51 12-25 00:56:09.331: WARN/InputManagerService(577): Got RemoteException sending setActive(false) notification to pid 722 uid 10020

  Read the article

• iPhone - database reading method and memory leaks

  - by Do8821

  Hi, in my application, a RSS reader, I get memory leaks that I can't fix because I can't understand from where they come from. Here is the code pointed out by Instruments. -(void) readArticlesFromDatabase { [self setDatabaseInfo]; sqlite3 *database; articles = [[NSMutableArray alloc] init]; if(sqlite3_open([databasePath UTF8String], &database) == SQLITE_OK) { const char *sqlStatement = "select * from articles"; if(sqlite3_prepare_v2(database, sqlStatement, -1, &compiledStatement, NULL) == SQLITE_OK) { while(sqlite3_step(compiledStatement) == SQLITE_ROW) { NSString *aName = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 1)]; NSString *aDate = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 2)]; NSString *aUrl = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 3)]; NSString *aCategory = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 4)]; NSString *aAuthor = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 5)]; NSString *aSummary = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 6)]; NSMutableString *aContent = [NSMutableString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 7)]; NSString *aNbrComments = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 8)]; NSString *aCommentsLink = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 9)]; NSString *aPermalink = [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, 11)]; [aContent replaceCharactersInRange: [aContent rangeOfString: @"http://www.mywebsite.com/img/action-on.gif"] withString: @"hellocoton-action-on.gif"]; [aContent replaceCharactersInRange: [aContent rangeOfString: @"hhttp://www.mywebsite.com/img/action-on-h.gif"] withString: @"hellocoton-action-on-h.gif"]; [aContent replaceCharactersInRange: [aContent rangeOfString: @"hthttp://www.mywebsite.com/img/hellocoton.gif"] withString: @"hellocoton-hellocoton.gif"]; NSString *imageURLBrut = [self parseArticleForImages:aContent]; NSString *imageURLCache = [imageURLBrut stringByReplacingOccurrencesOfString:@":" withString:@"_"]; imageURLCache = [imageURLCache stringByReplacingOccurrencesOfString:@"/" withString:@"_"]; imageURLCache = [imageURLCache stringByReplacingOccurrencesOfString:@" " withString:@"_"]; NSString *uniquePath = [tmp stringByAppendingPathComponent: imageURLCache]; if([[NSFileManager defaultManager] fileExistsAtPath: uniquePath]) { imageURLCache = [@"../tmp/" stringByAppendingString: imageURLCache]; [aContent replaceCharactersInRange: [aContent rangeOfString: imageURLBrut ] withString: imageURLCache]; } Article *article = [[Article alloc] initWithName:aName date:aDate url:aUrl category:aCategory author:aAuthor summary:aSummary content:aContent commentsNbr:aNbrComments commentsLink:aCommentsLink commentsRSS:@"" enclosure:aPermalink enclosure2:@"" enclosure3:@""]; [articles addObject:article]; article = nil; [article release]; } } sqlite3_finalize(compiledStatement); } sqlite3_close(database); } ` I have a lot of "Article" leaked and NSString matching with these using : [NSString stringWithUTF8String:(char *)sqlite3_column_text(compiledStatement, X)]; I tried a lot of different code I always have these leaks. Anyone has got an idea to help me?

  Read the article

• Why does the rename() syscall prohibit moving a directory that I can't write to a different director

  - by Daniel Papasian

  I am trying to understand why this design decision was made with the rename() syscall in 4.2BSD. There's nothing I'm trying to solve here, just understand the rationale for the behavior itself. 4.2BSD saw the introduction of the rename() syscall for the purpose of allowing atomic renames/moves of files. From 4.3BSD-Reno/src/sys/ufs/ufs_vnops.c: /* * If ".." must be changed (ie the directory gets a new * parent) then the source directory must not be in the * directory heirarchy above the target, as this would * orphan everything below the source directory. Also * the user must have write permission in the source so * as to be able to change "..". We must repeat the call * to namei, as the parent directory is unlocked by the * call to checkpath(). */ if (oldparent != dp->i_number) newparent = dp->i_number; if (doingdirectory && newparent) { VOP_LOCK(fndp->ni_vp); error = ufs_access(fndp->ni_vp, VWRITE, tndp->ni_cred); VOP_UNLOCK(fndp->ni_vp); So clearly this check was added intentionally. My question is - why? Is this behavior supposed to be intuitive? The effect of this is that one cannot move a directory (located in a directory that one can write) that one cannot write to another directory that one can write to atomically. You can, however, create a new directory, move the links over (assuming one has read access to the directory), and then remove one's write bit on the directory. You just can't do so atomically. % cd /tmp % mkdir stackoverflow-question % cd stackoverflow-question % mkdir directory-1 % mkdir directory-2 % mkdir directory-1/directory-i-cant-write % echo "foo" > directory-1/directory-i-cant-write/contents % chmod 000 directory-1/directory-i-cant-write/contents % chmod 000 directory-1/directory-i-cant-write % mv directory-1/directory-i-cant-write directory-2 mv: rename directory-1/directory-i-cant-write to directory-2/directory-i-cant-write: Permission denied We now have a directory I can't write with contents I can't read that I can't move atomically. I can, however, achieve the same effect non-atomically by changing permissions, making the new directory, using ln to create the new links, and changing permissions. (Left as an exercise to the reader) . and .. are special cased already, so I don't particularly buy that it is intuitive that if I can't write a directory I can't "change .." which is what the source suggests. Is there any reason for this besides it being the perceived correct behavior by the author of the code? Is there anything bad that can happen if we let people atomically move directories (that they can't write) between directories that they can write?

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >