Search Results

Search found 30252 results on 1211 pages for 'network programming'.

Page 1083/1211 | < Previous Page | 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090  | Next Page >

• Giving VPN connections access to all locations?

  - by Jeff

  I have asked a similiar question, but didn't get any answers so i am going to try and rephrase. i have 4 locations corporate and 3 remotes when you are at the corporate location, you have full access to all networks. 192.168.3.x 192.168.2.x 192.168.1.x 192.168.0.x all locations are connected via site-to-site vpn with the corporate location. if you are at a remote location, you have access to that location & the corporate location. the corporate location handles all VPN traffic. however, when you VPN into the corporate location, you can not see outside the corporate location. can anyone provide some information or a link explaining how to allow the VPN users to see all locations? thanks static route configuration: Gateway of last resort is 207.255.x.1 to network 0.0.0.0 C 207.255.x.0 255.255.255.0 is directly connected, outside S 10.0.1.6 255.255.255.255 [1/0] via 207.255.x.1, outside S 10.0.1.5 255.255.255.255 [1/0] via 207.255.x.1, outside S 192.168.0.0 255.255.255.0 [1/0] via 192.168.0.1, inside C 192.168.1.0 255.255.255.0 is directly connected, inside S 192.168.2.0 255.255.255.0 [1/0] via 192.168.2.1, inside S 192.168.3.0 255.255.255.0 [1/0] via 192.168.3.1, inside S* 0.0.0.0 0.0.0.0 [1/0] via 207.255.x.1, outside [1/0] via 192.168.1.1, outside

  Read the article

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad?

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• IIS FTP error: 426 Connection closed; transfer aborted.

  - by Jiaoziren

  Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

  Read the article

• DNS Does Not Register at Off-site Locations

  - by Russ Warren

  First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

  Read the article

• Trying to delete a directory stored on a WIndows server, mounted on a mac

  - by AdamG

  I am trying to delete a directory stored on a Windows 2008 R2 server, mounted on a Mac as network home (10.8.5). The directory was created by Safari and stores temporary internet files. I need to be able to delete this folder on logout from a Mac bash script. The Terminal on Mac shows the directory as empty: 36W-FacRm-02:History lwickham$ cd /home/lwickham/Library/Caches/Metadata/Safari/History 36W-FacRm-02:History lwickham$ ls -al total 0 drwx------ 1 lwickham CGPS\Domain Users 264 Nov 8 09:24 . drwx------ 1 lwickham CGPS\Domain Users 264 Nov 8 09:28 .. However, on the Windows server it has a single 0kb file that doesn't start with a "." but yet is invisible to the Mac. E:\FacultyHome2\lwickham\Library\Caches\Metadata\Safari\History>dir Volume in drive E is FacultyUsers2 Volume Serial Number is 8C17-4EF3 Directory of E:\FacultyHome2\lwickham\Library\Caches\Metadata\Safari\History 11/08/2013 09:24 AM <DIR> . 11/08/2013 09:24 AM <DIR> .. 11/07/2013 04:28 PM 0 http?%2F%2Fwww.google.com%2Furl?sa=t&rct= j&q=&esrc=s&source=web&cd=6&ved=0CFsQFjAF&url=http%253A%252F%252Fwww.usbanklocat ions.com%252Fhsbc-bank-usa-96th-street-branch.html&ei=5vR7UtmXEPjfsATe0YCIBA&usg =AFQjCNF9ypKbpYbXRng00FY3W8Y6cF1Tiw&bvm=bv.56146854,d. 1 File(s) 0 bytes 2 Dir(s) 514,231,967,744 bytes free All my attempts to delete the dir from the Mac have failed: 36W-FacRm-02:History lwickham$ rm -fr /home/lwickham/Library/Caches/Metadata/Safari/History/* 36W-FacRm-02:History lwickham$ rm -frd /home/lwickham/Library/Caches/ rm: /home/lwickham/Library/Caches//Metadata/Safari/History: Directory not empty rm: /home/lwickham/Library/Caches//Metadata/Safari: Directory not empty rm: /home/lwickham/Library/Caches//Metadata: Directory not empty rm: /home/lwickham/Library/Caches/: Directory not empty

  Read the article

• Using a Linksys Wireless- G Broadband Router for a Wireless Antenna/Adapter?

  - by Alex

  (Warning: I'm not too computer-smart). Just moved fm a home where I used ATT DSL to a home w/ Comcast Cable for internet. Old home had the DSL ethernet wired to my only desktop w/ a 2Wire router for my wireless signal for the laptops. In the new home the signal comes fm cable via a Netgear(300) wireless router (remotely located) & works fine for my laptops. After searching with the network software, my desktop (can't be ethernet wired cuz of location) detects no wireless signal. Desktop is a 2 yr old HP p6311f Pavilion (Windows 7). Can't seem to detect any wireless hardware (ant/adaptr). Maybe I don't have the ability & need to buy a USB wireless antenna? Would the Pavilion come w/ wireless capability out of the box, maybe something inside the tower? No antenna on back. I happen to have a Linksys Wireless router which I plugged in to the desktop (trying both internet & shared ports) & noticed signal action on the router front panel. No internet on desktop though. Can I use this as an antenna for the desktop? Thanks & sorry if my solution is an easy one I'm just missing. Just want internet on the desktop.

  Read the article

• How does the LeftHand SAN perform in a Production environment?

  - by Keith Sirmons

  Howdy, I previously asked this ServerFault question: Does anyone have experience with lefthands VSA SAN The general consensus looks like it does not perform well enough for a production SQL server even at a light load. So the new question is, How does LeftHand's SAN perform on the HP or Dell dedicated Hardware boxes? We are looking at the Starter SAN with 2 HP nodes in a 2-way replication, 2 ESX servers hosting a total of 2 Active Directory server, 1 MS SQL server, 1 File Server, and 1 General Purpose Server for things like Virus Scan (All Microsoft Server 2005 or 2008). The reason I am looking at LeftHand is for the complete software package. I plan to have a DR site and like how the SAN can perform an Async Replication to the offsite location without having to go back to the Vendor for more licenses. I also like the redundancy built into the Network Raid architecture. I have looked at other SANS and found different faults with them. For example, Dell's EqualLogic: Found that although the individual box is very redundant in hardware, the Data once spanned across multiple boxes is not redundant, if a node goes down you have lost the only copy of the data sitting on that hardware (One thing is certain, all hardware fails... When? is the only question.). I have used an XioTech SAN as well.. Well worth the money BTW, but I think it is overkill for the size of the office I am targeting. The cost to get the hardware redundancy in the XioTech makes it a little out of reach for the budget I am working in. Thank you, Keith

  Read the article

• What parts should I get for an ASRock x58 Extreme motherboard

  - by Brad Gilbert

  I just received an ASRock x58 Extreme motherboard, for my post on this question. It was a 2009 Tom's Hardware recommended buy. It is a Core i7 motherboard, with an X58 Express Chipset. It uses DDR3 RAM. What I want to know is, what parts should I get to finish it off. I'm looking for some good bargains, because of a lack of funds. The most taxing game I will probably play on it is OpenTTD. The only parts I currently have that are compatible: A Dynex 400W power supply. It appears to be an ATX 2.1 power supply, with the addition of a -5 rail. Apparently designed to be compatible with most ATX-style motherboards. Several PCI add-in cards. Mostly 10/100 Network cards Some sound cards Some video cards with a VGA connector Plenty of PATA drives. 8 GB - 80 GB Hard-drives A dozen or-so CD-ROM drives, only a handful of them are CD-RW drives. One DVD-ROM drive I have one LCD, with a 15 pin VGA connector, which I salvaged from the dump. The only thing wrong with it was some dead capacitors. It also has a stuck pixel.

  Read the article

• WD my cloud 4th is Super Slow

  - by Saduser

  I am using a WD my cloud 4Tb and I have read other posts about users complaining about getting only 10Mb per second. My problem is that I am getting about 100kb/s to transfer a 125gb iPhoto library. Estimated time is 11 days to transfer this file. This is unacceptable. On the back of the WD cloud I am getting a solid green light and from what I read this means that I am on a gigabyte network. I have mac book pro running Mac OS Mavericks. I have tried 4 different cables and turned off my router firewall. I don't run anti-virus nor any firewall on the mac. Other things I have checked: direct connection to both router and WD cloud device. Tried wireless but it is even slower. Previously I was able to transfer a 55Gb iPhoto library in 14 hours which I felt was acceptable. I figured it would take approximately double the time to transfer the 125gb file but 11 days is ridiculous. Any other suggestions? Anything else I can check (how to check it) what is the bottle neck?

  Read the article

• Opening port 80 in router has no results

  - by Ricardo Pieper

  A friend of mine has a ADSL modem and I need to forward some ports. I have already forwarded the 1521 port (Oracle) and it's working fine. Now I need to forward the port 80. I already set up his IIS bindings to this port, and also forwarded the port like this video shows: https://www.youtube.com/watch?v=DLKD-fyexoo So I think I did everything correctly. The local IP address is also the same as the machine where the IIS server is running. I'm sorry, but I can't post images since i don't have 10 points :( Somehow I can't forward this port, yougetsignal.com keeps saying that the door is closed. When I try to open the port, the Control Panel says me that I have to access the control panel in the 8080 port, because the 80 port will be open. Ok, that's fine. But I'm still able to access it in the 80 port, and when I try to access it in the 8080 port, it doesn't work. I'm trying it with the TPLINK 8816, but I also tried to open it in the Opticom DsLink 279, and it didn't worked (using another machine), I got the exact same results. He has a dynamic IP address, but he is also using No-ip, so I can always access his Oracle database in a certain static address. The 1521 port is open. I also tried to disable the firewall in Windows, but that makes no sense to me, since the router doesn't really open the port 80. Clearly I'm missing something. I have never done it in my life, so I dont know how to proceed. Restarting the router was the first I did, no results. I'm accessing his laptop through TeamViewer, so I'm testing the port outside his local network. Edit: My ISP says that they allow to open ports, and the 1521 port is opened. What could I do to open the 80 port?

  Read the article

• Servers in DMZ will not communicate with each other

  - by Tukaro

  (Full disclosure: I rate barely above "noob" when it comes to networking.) My workplace recent got a new web server. Since we're nearing the end of an overhaul of our website, we're doing a slooooow migration between the old web server and the new one. The old webserver (we'll call it SERVOLD) is Windows Server 2008 with IIS 7. It does not have SQL Server installed. The new server (SERVNEW) is Windows Server 2008 R2, IIS 7.5, with the same version of SQL Server installed. Both are located in the DMZ for our network, and both have their own outward-facing IP address (.3 and .4, respectively). Each server can communicate fine with computers within the domain (not in the DMZ), and those same computers have no trouble communicating with either server. Both servers are also accessible from the internet just fine. However, no matter what, these two servers just refuse to recognize each other. They have the same Workgroup name listed (WORKGROUP), and I thought that would be enough for them to recognize each other. What needs to happen such that I can get these two servers to communicate with each other? We want to do a gradual roll-over to the new website (new one uses ASP.NET, old one uses CFMX), so being able to use one database between both servers is a necessity. Thanks!

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• Route all traffic via OpenVPN client

  - by Ilya

  I've got OpenVPN client running on 192.168.0.3. What I'd like to do is route all the traffic from the second computer with 192.168.0.100 via OpenVPN client that's running on the first computer. My router ip is 192.168.0.1 Network topology: Windows computer with OpenVPN client: 192.168.0.3 Windows computer whose traffic has to be rerouted: 192.168.0.100 Router: 192.168.0.1 I want it to work in the following way: 192.168.0.100 computer => 192.168.0.3 computer => OpenVPN => 192.168.0.1 How can I achieve that by only modifying windows' routing table? I've tried entering the following into windows shell(on computer without VPN), which didn't work (it just dropped my internet connection): route delete 0.0.0.0 mask 255.255.255.255 192.168.0.1 route add 0.0.0.0 mask 255.255.255.255 192.168.0.3 Should I also setup the computer that has OpenVPN client running? Does it have anything to do with windows tcp forwarding? Thanks!

  Read the article

• Datacenter IP Addressing and DNS Management

  - by user65248

  Hello everyone Basically we are setting up a small Datacenter, about 300 amps power and max 50 racks, Im saying these coz I wanna u imagine the size and requirements, I have studied networking mostly Microsoft and Windows based systems , but I cant get how the IP addressing and DNS management and configuration works in a Datacenter , and unfortunately I have to setup everything by myself but defe we will have some staff to do some job. Now my questions Datacenter IP Addressing Suppose we have got a block of 200 IP addresses from our ISP, How can I manage these block of IP addresses, is there any software out there to simplify this I heard that using DHCP server in a datacenter is not recommended, otherwise what would u say about MS DHCL server ofc considering we need to have backup serversin case of failur How can I assign a block of IPs to a specific rack, I know with different software and management its different but Im asking how it is done normally IP addresses are exposed to the whole network, what if a customer try to use an IP address and is not assigned to their server or rack , how can I prevent this or how can I track the IP usage DNS Management Im goin to setup at least two servers for our DNS servers, I know nothing about Datacenter DNS system, but I have configured DNS server in normal networks and also for webservers, Now I wanna know What exactly needs to be done for a DNS in a datacenter that is not done for normal networks. How can I configure PTR records why cant I configure PTR records on my webserver side DNS server and it should be done on datacenter DNS server , I mean what is the difference in DC DNS servers that allow us to to so , I know the question is very silly and simple but Im confused Is there any software outthere to allow doing the whole thing, I mean automatically add records to the DNS and also managin IP addresses !? Thanks in advance

  Read the article

• Embedding a WMV file on the web via URL in a Powerpoint presentation

  - by Dave

  I've got a situation where I want to distribute a Powerpoint presentation to several people. I want to be able to embed several large videos in this presentation by linking to a URL, for the following specific reasons: the videos are highly confidential, and I would like to be able to delete them at some later date, but still allow them to see it in the presentation while it is online. I want to send the presentation via email (so it should be small), and put the links on a server with a faster upload speed Maybe I'd like to change the video at some point without changing the presentation One option that addresses #1 is to hook up a webcam and allow them to see video stream from the office, but our upload rate is too slow for this to be a viable option. I've tried embedding a video and giving Powerpoint the URL. It seems to work initially, because the first frame appears in my slideshow. However, when I play the slideshow, nothing happens. I looked at the network traffic on my computer, and nothing was getting downloaded from the remote server. Any suggestions on how to make this work, or how to at least satisfy the criteria listed above would be great!

  Read the article

• How to enable Ipv6 on my ubunutu 11.04 virtual machine

  - by liv2hak

  I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

  Read the article

• What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

  - by xzenox

  I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• VNC server failed to start CentOS

  - by Shaun

  I followed a tutorial on how to install and get VNCserver to run on CentOS 6 (since freenx isnt supported yet) and I keep getting Starting VNC server: 1:user [FAILED] How do I figure out whats going on here? Im new to Linux/CentOS and im trying to get RDP going so I can step away from SSH as much as possible (you know us Windows users love our pretty GUI's). So, where is the error log at and how do I find it? Or maybe someone else has experienced this and knows the solution based on the simple error given? After running in debug mode, here is my error + . /etc/init.d/functions ++ TEXTDOMAIN=initscripts ++ umask 022 ++ PATH=/sbin:/usr/sbin:/bin:/usr/bin ++ export PATH ++ '[' -z '' ']' ++ COLUMNS=80 ++ '[' -z '' ']' +++ /sbin/consoletype ++ CONSOLETYPE=pty ++ '[' -f /etc/sysconfig/i18n -a -z '' -a -z '' ']' ++ . /etc/profile.d/lang.sh ++ unset LANGSH_SOURCED ++ '[' -z '' ']' ++ '[' -f /etc/sysconfig/init ']' ++ . /etc/sysconfig/init +++ BOOTUP=color +++ RES_COL=60 +++ MOVE_TO_COL='echo -en \033[60G' +++ SETCOLOR_SUCCESS='echo -en \033[0;32m' +++ SETCOLOR_FAILURE='echo -en \033[0;31m' +++ SETCOLOR_WARNING='echo -en \033[0;33m' +++ SETCOLOR_NORMAL='echo -en \033[0;39m' +++ PROMPT=yes +++ AUTOSWAP=no +++ ACTIVE_CONSOLES='/dev/tty[1-6]' +++ SINGLE=/sbin/sushell ++ '[' pty = serial ']' ++ __sed_discard_ignored_files='/\(~\|\.bak\|\.orig\|\.rpmnew\|\.rpmorig\|\.rpmsave\)$/d' + '[' -r /etc/sysconfig/vncservers ']' + . /etc/sysconfig/vncservers ++ VNCSERVERS='1:larry 2:moe 3:curly' ++ VNCSERVERARGS[1]='-geometry 800x600' ++ VNCSERVERARGS[2]='-geometry 640x480' ++ VNCSERVERARGS[3]='-geometry 640x480' + prog='VNC server' + RETVAL=0 + case "$1" in + start + '[' 0 '!=' 0 ']' + . /etc/sysconfig/network ++ NETWORKING=yes ++ HOSTNAME=vps.binaryvisionaries.com ++ DOMAINNAME=server.name ++ GATEWAYDEV=venet0 ++ NETWORKING_IPV6=yes ++ IPV6_DEFAULTDEV=venet0 + '[' yes = no ']' + '[' -x /usr/bin/vncserver ']' + '[' -x /usr/bin/Xvnc ']' + echo -n 'Starting VNC server: ' Starting VNC server: + RETVAL=0 + '[' '!' -d /tmp/.X11-unix ']' + for display in '${VNCSERVERS}' + SERVS=1 + echo -n '1:larry ' 1:larry + DISP=1 + USER=larry + VNCUSERARGS='-geometry 800x600' + runuser -l larry -c 'cd ~larry && [ -r .vnc/passwd ] && vncserver :1 -geometry 800x600' + RETVAL=1 + '[' 1 -eq 0 ']' + break + '[' -z 1 ']' + '[' 1 -eq 0 ']' + failure 'vncserver start' + local rc=1 + '[' color '!=' verbose -a -z '' ']' + echo_failure + '[' color = color ']' + echo -en '\033[60G' + echo -n '[' [+ '[' color = color ']' + echo -en '\033[0;31m' + echo -n FAILED FAILED+ '[' color = color ']' + echo -en '\033[0;39m' + echo -n ']' ]+ echo -ne '\r' + return 1 + '[' -x /usr/bin/plymouth ']' + /usr/bin/plymouth --details + return 1 + echo + '[' 1 -eq 98 ']' + return 1 + exit 1

  Read the article

• Error when connecting to shared Windows Printers

  - by TrueDuality

  I'm replacing our Windows 2003 print server with one running on Windows 2008 R2. I have connected and configured all of our printers and can successfully print to them from the server itself. All of the printers are shared and user's have permission to print on all of them. Whenever one of our clients attempts to connect through the shares they receive the following error message: Operation could not be completed (error 0x0000709). Double check the printer name and make sure that the printer is connected to the network. No messages are generated on the client Event Log nor is anything generated on the server. I have reinstalled the drivers as suggested by a few forum posts I came across and it didn't solve the issue. There are twelve different printer drivers and they are all experiencing this issue so I believe it is unrelated to the driver. I have disabled UAC on both the client and server since that has caused so many headaches before, but it too did not solve this problem. Does anyone have any idea what may be causing this?

  Read the article

• Huge host CPU usage in idle vmware guest. Ubuntu 10.04 host, Vista SP2 guest

  - by themesandmodules

  I'm experiencing huge host CPU usage with an idle vmware guest. Host: Ubuntu 10.04 32-bit 2.6.32-24-generic-pae. (Very new install, i.e 24 hours ago) Hardware is Dell XPS M1530 laptop, 4GB ram. Intel Core II Duo T9300 2.50Ghz The virtualization setting "VT" or something is enabled in my bios. Guest: Completely fresh install of Windows Vista, upgraded to latest SP2 and all windows updates installed. 1024 - 1512MB ram allocated. Absolutely no other software installed on it, apart from VMWare tools. Situation When the guest is doing absolutely nothing, I watch with sysinternals process watch on the guest. This shows that system idle process is between 70 and 99%, usually around 95%. No actual process doing anything. On the host, I watch with top, I get cpu usage of 20% - 80%, usually around 30%. What I have tried Single and Dual processor available to guest - no change. Turn off all peripherals to guest - no network, drives, usb etc - no change. Turn off 3d acceleration for guest - perhaps a small improvement, or no change. Upping allocated ram to guest from 1024MB to 1512MB - no change. Yelling at vmware - no change. I have experienced a similar issue in the past, which was solved by setting the guest to have 1 CPU. This time that hasn't worked.

  Read the article

• Exchange 2003 IMAP not working for some users

  - by John Gardeniers

  We normally don't have a need for IMAP connections from outside the company network but in order to allow a one user to use IMAP on a portable device I've turned it on and opened port 993 on the firewall. When the user in question was unable to get connected I tested this using Outlook remotely. Start by creating a new IMAP account in Outlook using a test account. No problems, it worked perfectly. Now try the same thing using the account of the user who actually needs to connect and it's a no-go. Outlook simply keeps prompting for logon credentials. Next I tried using my own account and that too failed. Testing with a couple of other accounts worked perfectly. Interestingly enough, with my own account I've used IMAP on a MAC before (internally) without a problem and I'm not aware of anything that has changed which could affect IMAP on my account. Checking the user settings in ADUC showed that all accounts have the same Exchange protocol settings. Specifically, IMAP is enabled. A check of the event logs on the server reveals no entries for the connection attempts, making this kind of difficult to debug. Has anyone here encountered such a situation and, even more importantly, what caused it?

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• DNS server not working?

  - by Behrooz A

  I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

  Read the article

< Previous Page | 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090  | Next Page >