Search Results

Search found 5734 results on 230 pages for 'forward declarations'.

Page 109/230 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• Windows 7 with two network cards doesn't route traffic

  - by Tomek

  I have simple task to do: I have wni7 with two nics.I want to connect another comp(osx) to win7 through second nic to connect it to internet. I already changed the registry. Win7 interface with 192.168.2.1 has no gateway set (no point to do that) OSX interface with 192.168.2.2 has gateway set to 192.168.2.1 I do not add any routes on win7, every thing seems to be already there network on second nic is detected as "undefined network" (probably effect of no gateway) i can achieve any connectivity to internet from OSX only by enabling network connection sharing on nic with 192.168.2.1, but it enables NAT and I'm interested only in pure routing without nat(it's a setup for some research). firewall is off. It seems to me that win7 refuses to forward packets for some reason. Perhaps "undefined network" and NLA service is to blame, although i couldn't find any info about that. Below ascii schematics of my setup: internet<--router(192.168.1.1)<--(192.168.1.1) WIN7 (192.168.2.1)<--(192.168.2.2)OSX Thanks

  Read the article

• Proxying/Tunneling IPSec traffic via netcat or SOCKS?

  - by MattC

  I have a client that is using a SonicWall router as their VPN concentrator. I downloaded the client software and set up the router as a peer. My issue is that my company uses a dual DMZ setup, meaning we have an interior firewall, then a bunch of DMZ servers, then an external firewall, then finally the telco router. In this setup, the interior firewall has no way to communicate with the exterior firewall since they are on two totally separate subnets. The communication occurs through the servers that straddle the networks. In this case, I need some way to forward the ISAKMP/IPSec traffic from my desktop out to the Internet. My usual trick of using netcat on the intermediate proxy server doesn't work here since it's not TCP/UDP traffic as far as I can tell. All of my previous experience with VPN's have been using SSL-based VPN's which are clearly very easily proxy-able. Any help would be appreciated, thanks!

  Read the article

• Block (or only allow certian) incoming IP addresses on Verizon FIOS Actiontec Router

  - by jmlumpkin

  I opened a few ports to the outside of my home network so I can get into a few of my machines from outside. When checking some logs, I noticed that I was getting scanned on some ports from various other countries. I already moved my port forward to a non-standard port. I would like to be able to block specific IP's (or even subnets) from my Verizon FIOS router. There is a little bit of documentation online, but I can't find anything specific on how to do this. To start, I just want to block a specific IP. But if it is not to hard, I would also like to know how to possibly block a range of IPs. And with the inverse of this - is there a way to allow only certain IPs or range?

  Read the article

• postfix cannot send email

  - by AKLP

  I'd like to mention that im really new to this so please bear with me. I'm trying to setup a forum software to send emails via postfix but I think my server has the port 25 blocked. I tried running these: works: ping alt2.gmail-smtp-in.l.google.com don't work: telnet alt2.gmail-smtp-in.l.google.com 25 telnet 66.249.93.114 25 tried flushing iptables and then using these rules but didn't work either: sudo iptables --flush sudo iptables -P INPUT ACCEPT sudo iptables -P OUTPUT ACCEPT sudo iptables -P FORWARD ACCEPT sudo iptables -F sudo iptables -X doing a telnet on 25 port to localhost url works but nothing when telnet'ing in none local urls. mail.log: Oct 17 01:20:24 webhost postfix/smtp[3642]: connect to alt2.gmail-smtp-in.l.google.com[2607:f8b0:400e:c03::1a]:25: Connection timed out Oct 17 01:20:24 webhost postfix/smtp[3643]: connect to alt2.gmail-smtp-in.l.google.com[2607:f8b0:400e:c03::1a]:25: Connection timed out Oct 17 01:20:24 webhost postfix/smtp[3642]: 4744380032: to=<[email protected]>, relay=none, delay=2892, delays=2741/0.03/150/0, dsn=4.4.1, status=deferred (connect to alt2.gmail-smtp-in.l.google.com[2607:f$

  Read the article

• Need advise on linking apache and tomcat

  - by hsnm

  I have been searching this for hours with no luck. I have a web server that uses https on Apache2. I also have installed tomcat7 on the same server to run some Java webapp on it. I need to keep my https port 443 on Apache but forward the requests to the Java webapp to tomcat. I tried to use mod_jk to redirect the requests to tomcat but I failed. Most tutorials talk about redirecting plain http requests not https. I also could not let tomcat use https on 8443. I'm following the steps here but facing errors. The question: Can I redirect https traffic to tomcat without installing https on tomcat? Is there a good tutorial you can recommend to me?

  Read the article

• Vmware Fusion 5 Port Forwarding

  - by Snap Shot

  I have a service (a node.js express app) running on port 3000 in a CentOS 6.3 guest that I would like to access in a web browser on my Mac Mountain Lion host using VMware Fusion 5 Professional. I am having trouble finding any information about how to do this. I believe I would like to forward the port but I cannot find any information about this using either the GUI or by modifying configuration files. In earlier versions it looks like you might have modified a file called nat.conf but that does not seem to apply to Fusion 5. Has anyone successfully done this? Thank you.

  Read the article

• Is email forwarding to the sender's address usually blocked in Mail servers / MTA?

  - by codecowboy

  I've noticed that email forwarding to an address seems not to work if I send an email from the address to which I am forwarding email. This happens for GMail and Fasthosts mail servers. e.g I send an email to [email protected] from [email protected] , [email protected] is set to forward to [email protected] and the email never arrives. I realise this seems logical but it is a potential cause of confusion when testing email functionality in a web application (for me, anyway ;-). I would just like to know if this is standard for all MTA software so I can avoid confusing myself.

  Read the article

• Windows Server 2003 stops sharing a folder when the server reboots [closed]

  - by evolvd

  I have a file server that will stop sharing a particular folder once the server is rebooted. This problem happened after the server went through a p2v migration. There are no events that seem to correlate to this issue. I was reading http://support.microsoft.com/default.aspx/kb/870964 but I don't think this applies and there are other shares on the same drive that are still there after a reboot. To be clear about the issue; When the server reboots share x is no longer shared any more but share y and z are still there. This has nothing to do with users not being able to see the share. On the server its self the folder that was shared is no longer shared. I wish I had more information to post but after hours on this issue I can't find a way to move forward.

  Read the article

• How to rename multiple files in multiple folders with 1 command

  - by Charles

  We want to rename our *.html files to *.php but (sadly enough) have not enough knowledge to do it with a dos batchfile and/or cmd prompt command. The problem is that each file is in seperat folder and yes talking about 1500+ different folder names. Using wildcards for the files I know is the '*' but using also a wildcard for folders is unknown to me. We probably need to use the (MSDOS) 'FOR' command but there I am stucked. Folder structure we use is: parent-folder/child-folder/grandchild-folder/file.html sample: games/A/game_name/file.html, games/B/game_name/file.html, games/C/game_name/file.html and so on. The parent folder is for all files the same, the child & grandchild folders are different for most files. After renaming these files to .php I assume following in the .htaccess will make a permanent redirect. RedirectMatch 301 (.).html$ http://oursite.com$1.php Looking forward to suggestions/answers, thnx in advance.

  Read the article

• Apache mod_remoteip and access logs

  - by GioMac

  Since Apache 2.4 I've started using mod_remoteip instead of mod_extract_forwarded for rewriting client address from x-forwarded-for provided by frontend servers (varnish, squid, apache etc). So far everything works fine with the modules, i.e. php, cgi, wsgi etc... - client addresses are shown as they should be, but I couldn't write client address in access logs (%a, %h, %{c}a). No luck - I'm always getting 127.0.0.1 (localhost forward ex.). How to log client's ip address when using mod_remoteip?

  Read the article

• Reverse proxy with SSL and IP passthrough?

  - by Paul

  Turns out that the IP of a much-needed new website is blocked from inside our organization's network for reasons that will take weeks to fix. In the meantime, could we set up a reverse proxy on an Internet-based server which will forward SSL traffic and perhaps client IPs to the external site? Load will be light. No need to terminate SSL on the proxy. We may be able to poison DNS so original URL can work. How do I learn if I need URL rewriting? Squid/apache/nginx/something else? Setup would be fastest on Win 2000, but other OSes are OK if that would help. Simple and quick are good since it's a temporary solution. Thanks for your thoughts!

  Read the article

• Callback from static library

  - by MortenHN

  I think this should be simple, but im having a real hard time finding information about this topic. I have made a static library and have no problem getting the basics to work. But im having a hard time figuring out how to make a call back from the static library to the main APP. I would like my static library to only use one header as front, this header should contain functions like: requestImage:(NSString *)path; requestLikstOfSomething:(NSSting *)guid; and so on.. These functions should do the necessary work and start a async NSURLConnection, and call back to the main application when the call have finished. How do you guys do this, what are the best ways to callback from a static library when a async method is finished? should i do this with delegates (is this possible), notifications, key/value observers. I really want to know how you guys have solved this, and what you regard as the best practices. Im going to have 20-25 different calls so i want the static library header file to be as simple as possible preferable only with a list of the 20-25 functions. UPDATE: My question is not how to use delegate pattern, but witch way is the best to do callbacks from static librarys. I would like to use delegates but i dont want to have 20-25 protocol declarations in the public header file. I would prefer to have only one function for each request. Thanks in advance. Best regards Morten

  Read the article

• Port Forwarding Using iptables on Ubuntu

  - by user141610

  This is the scenario. I have configured a web-server in MUX. Now I want to access that web-server from Internet. Ubuntu box has two interfaces, One is connected to WAN (Public IP) and another one is connected to MUX (Private IP). MUX has no option to insert default gateway. iptables -t nat -A PREROUTING -p tcp -i eth0 -d 103.x.x.x --dport 8001 -j DNAT --to-destination 192.168.1.2:8080 iptables -A FORWARD -p tcp -d 192.168.1.2 --dport 8080 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT It does not work. Thanks...

  Read the article

• How to intercept and manipulate DNS queries?

  - by emtunc

  I'm not sure if I worded the question correctly to be honest but basically what I want to do is: When a user types in something like Expenses in the URL bar of a browser, I want the browser to be directed to a specific web address (very very similar to how OpenDNS shortcuts work) The IP address of the web address will not change amongst the different 'shortcuts'... i.e: mycompany.com = 10.0.0.0 mycompany.com/expenses = 10.0.0.0 mycompany.com/tracker = 10.0.0.0 When a user types expenses in the browser address bar and presses enter, I want the browser to automatically direct to the specified address as above. Would this be tricky to implement? I hope I have put my question forward appropriately :-) Additional notes: We are on a Windows envionment I believe the exchange server is running as the DNS server in the office

  Read the article

• Running multipul lines through a server.

  - by Kevin Roberson

  I am looking to buy numbers in bulk on DIDx.net. After I purchase the numbers in a particular area code, I want to forward those numbers to other numbers that are outside of that area code. This way it will be seen as a local call versus long distance. I have the customers but I don't have the system I need. I have read about Asterisk, VOIP, SIP, and BYOH. But I have no clue what will be the best system for me. Does anyone have any idea what my next step should be when it comes to hardware and software? Or what type of operating system I should use? I basically want to set up a system like GoogleVoice & Phonebooth.

  Read the article

• Suggestion for live video stream aggregation/switching/forwarding/management software?

  - by deceze

  I'm looking for a software or system that can receive video streams from a number of cameras via a network (RTMP or similar protocol), present a visual overview of all video streams and allow me to forward/send a selected stream to another service (e.g. to a Flash Media Server, or anywhere via RTMP). Basically the digital internet equivalent of a TV studio control panel, which allows a director to put together a live show. Is there any such software at an affordable price? A GUI-less server which can be scripted to switch streams would be good too. I'm not even quite sure what kind of product category this falls into or what search terms to plug into Google. Most results I have come up with have little more than an executive summary description which doesn't tell me anything. Any suggestion welcome.

  Read the article

• ant conditions problem

  - by senzacionale

  I have problem with ant. I woul dlike to use conditions in ant. But i get error of: BUILD FAILED C:\Projekti\Projekt ANT\build.xml:412: Problem: failed to create task or type Cause: The name is undefined. Action: Check the spelling. Action: Check that any custom tasks/types have been declared. Action: Check that any / declarations have taken place. and this is code: <target name="test"> <input message="Write some text: " addproperty="foo" /> <if> <equals arg1="${foo}" arg2="bar" /> <then> <echo message="The value of property foo is 'bar'" /> </then> <elseif> <equals arg1="${foo}" arg2="foo" /> <then> <echo message="The value of property foo is 'foo'" /> </then> </elseif> <else> <echo message="The value of property foo is not 'foo' or 'bar'" /> </else> </if> </target>

  Read the article

• How do I setup a syslog server for my network?

  - by Solignis

  I would like to setup a syslog server to forward all log file from all of my VMs and servers. I really don't much about what is out there. So I turn to the community, Something on Linux is fine, what I want more is alert ability like emails telling me something is not right. If there was something to sort the logs by source that would be cool. Where would I want run the syslog server from? My admin WS or a server/VM? Any input would be wonderful. Thanks in advance.

  Read the article

• Using rsyslog to create different log files for different processes

  - by user80203

  Scenario: I am running a cluster of machines. Each machine runs various python programs with a unique (across the cluster), but dynamically set, ID. Right now, they are all logging locally. So, I might have logs that look like: process_5.log process_6.log for processes that had ID's 5 and 6. Another machine may have: process_20.log process_25.log I wish to forward these logs to a logserver running rsyslogd. Python's logging facility has a nice syslog handler, so I understand how I could connect to the remote server. What I haven't figured out is how to use templating/DynFile to maintain log separation. e.g. on the logserver, I will want to see: process_5.log process_6.log process_20.log process_25.log which correspond to the logs of the same name on the sending machine. Is there a way to pull this off with rsyslogd templating?

  Read the article

• Proxy - Some general questions

  - by user68802

  Is it possible to accomplish the following scenario with a proxy server? We are having one internet facing server that we want to put behind a proxy for some reasons. We want everything to work as before. When they do a request all connections will be forward to the internal server which will send back the information through the proxy. We want to be able to change to proxy to show an maintenance page whenever we are doing maintenance and change it back to forwarding traffic when we are done. We do also want to be able to keep forwarding all users that are using the sites but show an maintenance page for all new users for a time before showing the maintenance page for everyone in order to give the users some time to finish their work before kicking them out.

  Read the article

• Is there a suitable chain for iptables when eth is in Promisc mode?

  - by user1495181

  I have a fron-end machine. Machine have2 eth cards. I want to use netfilter queue to do some checks on the packets. I set eth like this: ifconfig eth0 0.0.0.0 promisc up ifconfig eth1 0.0.0.0 promisc up I want to have an iptable rule like this(only example): iptables -A INPUT -i eth0 -j LOG --log-prefix " eth0 packet " but the packet is no passed through the iptables ,because it dosnt target to this MAC. Promisc mode didnt help. I saw that there is a way to add iptables chain for PROMISC, but need compilation... Is there any simplier way to have iptables rule when packet is not target to this eth. Currently i bypass this by creating a bridge between 2 eth and put rule on the FORWARD, but i done want to create bridge.

  Read the article

• Monitoring the wall time of a process on windows?

  - by Sean Madden

  Windows Task Manager has the ability to show the current CPU time of any given running process on windows, is there any way (not necessarily through Task Manager) to get the current wall time of a process? An example, let's say I have a script that reliably runs for about 45 minutes. Without adding a progress bar to the script, is there any way to figure out for how long it has been running? The math behind this seems pretty straight forward; WallTime = CurrentWallTime - WallTimeProcessStarted. Likewise, since the math is so simple, is there anyway to get the time that a process was started at?

  Read the article

• Replacing old server with new but different hostname & same IP

  - by MaxFr

  We have an old server 2000 and lots of users point to it by hostname and by its IP e.g \\server1, we have a new server 2008 R2 with new name serverlocation1 All folders and data have been sync'toy'd from the old server1 across to serverlocation1 each evening, the new server tree is exactly the same on the new server and all perms are correct. We need to make the new server the same IP as the old server1 as too many people access it directly via IP, and to ensure file and folder paths stay ok, anything \\server1\folder\file needs to go to \\newserverlocation1\folder\file etc I can change the old server1 name to server1-old & change IP and assign the old IP to the new server, but how do I force anything coming in for \\server1 to go to the new server and ensure anything referenced to the old server goes onto the new server ? I can CNAME but I need the new server to have the IP of the previous server so not sure if its straight forward etc..... point server1 to newserverlocation1 Then probably change DNS so that the OLD IP points to new hostname..... Any clarification appreciated.

  Read the article

• In Java, is there a gain in using interfaces for complex models?

  - by Gnoupi

  The title is hardly understandable, but I'm not sure how to summarize that another way. Any edit to clarify is welcome. I have been told, and recommended to use interfaces to improve performances, even in a case which doesn't especially call for the regular "interface" role. In this case, the objects are big models (in a MVC meaning), with many methods and fields. The "good use" that has been recommended to me is to create an interface, with its unique implementation. There won't be any other class implementing this interface, for sure. I have been told that this is better to do so, because it "exposes less" (or something close) to the other classes which will use methods from this class, as these objects are referring to the object from its interface (all public method from the implementation being reproduced in the interface). This seems quite strange to me, as it seems like a C++ use to me (with header files). There I see the point, but in Java? Is there really a point in making an interface for such unique implementation? I would really appreciate some clarifications on the topic, so I could justify not following such kind of behavior, and the hassle it creates from duplicating all declarations.

  Read the article

• OCaml delimiters and scopes

  - by Jack

  Hello! I'm learning OCaml and although I have years of experience with imperative programming languages (C, C++, Java) I'm getting some problems with delimiters between declarations or expressions in OCaml syntax. Basically I understood that I have to use ; to concatenate expressions and the value returned by the sequence will be the one of last expression used, so for example if I have exp1; exp2; exp3 it will be considered as an expression that returns the value of exp3. Starting from this I could use let t = something in exp1; exp2; exp3 and it should be ok, right? When am I supposed to use the double semicol ;;? What does it exactly mean? Are there other delimiters that I must use to avoid syntax errors? I'll give you an example: let rec satisfy dtmc state pformula = match (state, pformula) with (state, `Next sformula) -> let s = satisfy_each dtmc sformula and adder a state = let p = 0.; for i = 0 to dtmc.matrix.rows do p <- p +. get dtmc.matrix i state.index done; a +. p in List.fold_left adder 0. s | _ -> [] It gives me syntax error on | but I don't get why.. what am I missing? This is a problem that occurs often and I have to try many different solutions until it suddently works :/ A side question: declaring with let instead that let .. in will define a var binding that lasts whenever after it has been defined? What I basically ask is: what are the delimiters I have to use and when I have to use them. In addition are there differences I should consider while using the interpreter ocaml instead that the compiler ocamlc? Thanks in advance!

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >