Search Results

Search found 448 results on 18 pages for 'linksys'.

Page 11/18 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Automatically repair network connection when it goes down.

  - by Spines

  Every hour or so my wireless router goes down, and everyone connected loses internet for a couple minutes. If I right click on my network connection and choose repair, I usually get internet back quicker. Is there a way I can automatically have it try to repair the connection once it goes down? Can I write a program to do this if there isn't a built in windows setting? BTW I'm using Windows XP. EDIT:My router is a Linksys WRT110 with Firmware Version: 1.0.04, and I have cable internet. The signal is 100%. I live in an apartment complex and there are about 15 other wifi networks visible to me, not sure if that has any effect.

  Read the article

• Setup Cisco RVS4000 QOS for VOIP

  - by andyknas

  Just switched from dedicated T1's with analog phone lines to cable modem with 10/2 uplink. We're having some VOIP call quality issues on the outgoing side when bandwidth is stressed and I need to setup QOS or a VLAN on our RVS4000 router. Currently all phone traffic (talkswitch device and ip phones) are on it's own d-link PoE switch, and all workstations are on a LinkSys 1GB switch. Both switches are plugged into ports on the RVS4000. I'd like to set it up so that the dlink port has ~512Mbsp dedicated to it for voice at all times. It's my understanding that with a VLAN or QOS I can set this up. I've got QOS setup already with port 5060 to have high priority but it doesn't seem to make a difference.

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• Setting up a wireless network with Verizon MiFi

  - by winarm

  I am trying to set up a home network. I live in a location without cable internet so I have a Verizon MiFi card. I have a few laptops at the moment and they each connect through the card but I want to set up an Ubuntu 10.10 server and see if I can use it for DHCP. I have a Trendnet TEG-S50G switch and the computer I plan to use for the server has a Linksys WMP-11 Wireless PCI card. Is there any other equipment I need in order to get this to work? Is this even doable? Is there a better way to make this happen?

  Read the article

• Network Map Issue.

  - by Amit Thakur

  Hi There.. I have a Linksys NAS200, I have several user in that. Only for My A/c i can't map network drive. When i try to excess my personal folder. no access coming..but i can open my personal folder in web browser.other user are able to acess their folder. It happed to me only. whenever i tried, its only showing one shared folder which is visble and shared to all user.. Please help me to map it.and create a network driver with my username/password...tried every possiblities... Thanks in advance for your comments// Amit

  Read the article

• DNS Server and Private HTTP / SOCKS Proxy

  - by DucDigital

  Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

  Read the article

• DNS Server and Private HTTP / SOCKS Proxy

  - by DucDigital

  Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

  Read the article

• ADSL Modem Goes Slower Than Dialup

  - by peter

  Hi All, I have two ADSL modems, the first one does not have wireless, but is configured and working fine at around 6 - 7 mbps (ADSL) on Orcon in New Zealand. I bought a Belkin N150 wireless router to replace the first one. I configured it exactly the same as the first one, but a speed test confirms that it is running slower than dial up. One difference I noticed is that the first modem (a linksys) came from Orcon, and didn't have an ADSL username and password set up. The Belkin modem on the other hand wouldn't let me leave the username and password field blank. Any ideas? I am a techy guy, so it doesn't appear to be anything obvious with the settings I have missed. Thanks.

  Read the article

• Why isn't Synergy working for me?

  - by Anthony

  It worked for about a week then stopped working. I'm trying to make it work between a Windows 7 laptop and a Windows XP laptop. My router is a Linksys E1000. I tried uninstalling and reinstalling the program multiple times. I've tried port forwarding. I've tried making exceptions in the firewall. I've tried disabling the firewalls. It might be relevant also that Input Director doesn't work either. What am I doing wrong?

  Read the article

• Home networking - Wireless switch?

  - by gamers2000

  I currently have a Linksys WRT160N that has a couple wireless clients and a few wired clients. We are planning to switch from DSL to cable and unfortunately, there isn't a cable point in a location close to the wired clients (i.e. the new location of the router would be too far from the wired clients to lay Ethernet cables). Thus, I was wondering if there was a wireless switch of some sort in which it would be a standard Ethernet switch that would connect to my wireless network? (This is a home network,of course.)

  Read the article

• Should I use 802.11n with a 15 Mbps ISP (Comcast Cable)?

  - by stackoverflowuser2010

  I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP. I know that 802.11n has a max bandwidth of 300 Mbps, and it would help for intra-house transfers, such as streaming video from one computer to another. But is there any benefit to 802.11n for Internet activity, such as web browswing, gaming, and streaming video from Netflix?

  Read the article

• Wireless clients have no route to ethernet clients in OpenWrt router

  - by superjoe30

  I'm using OpenWrt Kamikaze 8.09 on a Linksys WRT54g v1.1 router. I just flashed it with default settings and got everything working, except my wireless laptop cannot ping my desktop which is wired to the router. What can I do to fix this? (My desktop can ping other desktops wired to the router) My routing table: config 'defaults' option 'syn_flood' '1' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'lan' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'wan' option 'input' 'REJECT' option 'output' 'ACCEPT' option 'forward' 'REJECT' option 'masq' '1' config 'forwarding' option 'src' 'lan' option 'dest' 'wan' option 'mtu_fix' '1' config 'redirect' option 'src' 'wan' option '_name' 'ssh' option 'proto' 'tcp' option 'src_dport' '22' option 'dest_ip' '192.168.1.100' option 'dest_port' '22' config 'redirect' option 'src' 'wan' option '_name' 'http' option 'proto' 'tcp' option 'src_dport' '8888' option 'dest_ip' '192.168.1.100' option 'dest_port' '8888'

  Read the article

• Allow Incoming Responses from Curl On Ubuntu 11.10 - Curl

  - by Daniel Adarve

  I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms Thanks in Advance

  Read the article

• Why is my router not routing?

  - by dwj

  Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

  Read the article

• Forwarding port to a VM - How to?

  - by Peter Gadd

  I use Win 8 Ent x64 on my PC, and I also have a Win 7 VMware virtual machine set up using a bridged network adapter. The IPv4 number for the Win 7 VM is 192.168.1.115. I require access to the VM from the Internet through port 1688. How do I set up port forwarding to achieve this? My router is a Cisco Linksys WAG120N. ========= If you require any further information to help me with this, I will gladly supply it. ========= Thanks in advance.

  Read the article

• How to set up a software VPN when moving a server to the cloud

  - by Neal L

  I work in a small company with one office in Dallas and another in Los Angeles. We run a Fedora server at our Dallas location and use a Linksys RV042 at each location to create a VPN connection between the sites. Every time the power or internet goes out in Dallas, our server is inaccessible so the entire company goes down. Because of this, we would like to use a shared server in the cloud (something like Linode) to avoid this problem. As a relative novice to VPN configurations, I would like to know if it is possible to set up a software VPN on the cloud server and connect our local networks in Dallas and LA to that VPN. I've read about openvpn and ssh vpns, but I don't know it is the best option. Could anyone with some experience point me in the right direction on the right combination of software VPN and hardware for this? We're open to new hardware to make this happen. Thanks!

  Read the article

• configure pppoe on wrt54gl(openwrt)

  - by sunny

  Hi, I have home DSL connection from my ISP with a beetel modem at my end. I want to make my network wireless, so i bought a linksys wrt54gl and installed open-wrt on it. My ISP provides dynamic IP's with me connecting via pppoe. My question is how do I configure openwrt to work with this. Please suggest what option should I go with, or any other you recommend. DSL cable--Beetel Modem-- Wrt54gl in bridge mode with beetel modem doing the pppoe and having a DHCP server. DSL cable--Wrt54gl with wrt54gl handling the pppoe. Is option 2 possible, can I have a setup without bringing the beetel modem in the picture at all?

  Read the article

• Two NIC cards with the same metric - Internet traffic going out the wrong one

  - by bvanderw

  I have two NIC cards in my computer - one is connected to our corporate network and the Internet, the other is connected to a private LAN through a Linksys WRT54G. Both cards use DHCP. This was never an issue with Windows XP, but with Windows Vista (and Windows 7) the metric for the 0.0.0.0 route is the same (20), and it appears that some network traffic that should go out my main network card are going out my secondary card instead. The solution to date is to delete the 0.0.0.0 route associated with the second NIC card, but I have to do this several times a day. Is there a better solution? --Bruce

  Read the article

• Should I remove all unmanged switches from my network?

  - by IMAbev

  I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

  Read the article

• Windows 7 Connection Sharing unable to access some sites

  - by Kristopher Ives

  I have a pretty sad networking situation that involves connecting to an open Wireless network and sharing that connection to an Ethernet that is plugged into a Linksys router. This has been done with XP and Windows 7, and it works great with XP. The problem with Windows 7 is that only some DNS will work. I don't know if it's been poisoned on the network above us (which we have no control over), but we've tried clearing the DNS cache as well as moving to using Google's DNS servers (8.8.8.8, 8.8.4.4). Here is a really quick list of sites that won't respond to DNS requests at all via dig, although if I get the IP address I can ping them: facebook.com yuilibrary.com twitter.com A lot of sites do work though. Anyone have an idea? It may be a subnet problem? If anyone wants more info let me know.

  Read the article

• Remote Desktop connection repeatedly aborting

  - by DerKlaus

  I connect to my workplace computer using Remote Desktop. After 1-2 minutes the application freezes to tell me after one more minute that the connection was aborted. It then reconnects. Everything works again for 1-2 minutes. Then the process repeats. Probably Forever. My coworkers do not experience such problems when connecting to the workplace. My workplace computer: Windows 7 32bit My home computer: Windows 7 64bit connected to the internet via WLAN-router with integrated ADSL modem (Linksys WAG200G) Things I already tried to fix the problem: disabled the Windows firewall disabled the other firewall reduced the MTU upgraded the firmware on the router configured port-forwarding to forward all packets to my home computer The problem remains unchanged. What could be the cause of the connection aborts? What else can I try to fix the connection? Thanks in advance.

  Read the article

• Setting up multiple wireless access points on same network

  - by SqlRyan

  I'd like to add wireless to my network, and I need multiple access points to cover the whole area. I'd like to set them up so that there's only one "wireless network" that the clients see, and it switches them as seamlessly as possible between access points as they wander around (if that's not possible, then at least have it so that they don't need to set up the security by hand on each one the first time, if possible). I've searched online, and there are quite a few sets of mixed instructions (same vs different SSID, frequency, does the security need to match exactly, etc.). Can somebody who has some experience doing this please let me know what they did? I imagine it's pretty simple, but there seems to be no clear cut "yes, you can do this" online, even though I know you can. I have a mid-size LAN with about 20 workstations and two Domain Controllers on it. Also, I'll be doing this with consumer wireless components, if it makes a difference, not enterprise-level components (ie. Linksys rather than Cisco).

  Read the article

• Need help connecting to NAS externally-port forwarding and DDNS newbie

  - by Joel

  Hi folks, I just picked up a synology NAS, and I'm loving it for internal use, but I want to be able to access the NAS externally-both from my iPhone (3G) and from the net. I have a Linksys WRT54G-TM router. My first question is whether I have set up the dyndns correctly. On my computer that is on my network, if I put in mydomain.dyndns.org, I am taken to a password popup and when I enter my router login and password, my router admin page opens up. On the same computer, I get the same results if I use my external IP address, and if I use my internal IP 192.168.0.1 So that is all as expected. However, when I go to my iphone and turn off wifi, and try to connect with 3g to the external IP or the dnydns domain, I just get an error "Safari could not open the page because the server stopped responding". What's up?

  Read the article

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• DDWRT or similar as repeater in a network.

  - by Quantumplation

  I have a friend with sever connection issues due to her wireless router being on the bottom floor of her house, and the computer being a story or two away. I have several old Linksys routers lying about, one of which is currently running DDWRT for my network. Would it be a good idea (effective) to configure one of these routers as a wireless bridge of some kind in an intermediary floor to improve her connection? Is there any specific configuration beyond the standard DDWRT setup that I would need to do? Thanks for your help. =)

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >