Search Results

Search found 86974 results on 3479 pages for 'visualsvn server'.

Page 1111/3479 | < Previous Page | 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118  | Next Page >

  • Install xenserver on iscsi target

    - by Ghassen Telmoudi
    Is is know that Xen Server is based on CentOS, and it is fact that CentOS can be installed on an ISCSI target flawlessly, but I wanted to install Xen server on an ISCSI target I couldn't find a way. I already tried the latest version of xen server 6.2, and there is no obvious way who to do the installation without a local disk. Does anybody have an idea about the subject, or did someone know how to do it? Please share your experience about this subject.

    Read the article

  • route to vpn based on destination

    - by inquam
    I have a VPN connection on a Windows 7 machine. It's set up to connect to a server in US. Is it possible, and if so how, to setup so that .com destinations uses the vpn interface and .se destinations uses the "normal" connection? Edit (clarification): This is for outbound connections. I.e. the machine conencts to a server on foo.com and uses the VPN and the machine connects to bar.se and uses the "normal" interface. Let's say foo.com has an IP filter that ensures users are located in USA, if I go through the VPN I get a US ip and everything is fine. But tif all traffic goes this way the bar.se server that has a IP filter ensuring users are in Sweden will complain. So I want to route the traffic depending on server location. US servers through VPN and others through the normal interface.

    Read the article

  • Nagios remote monitoring: NRPE Vs. SSH

    - by sam
    We use Nagios to monitor quite a few (~130) servers. We monitor CPU, Disk, RAM and a few other things on each server. I've always used SSH to run the remote commands, purely because it requires little to no additional config on the remote server, just install nagios-plugins, create the nagios user and add the SSH key, all of which I've automated into a shell script. I've never actually considered the performance implications of using SSH over NRPE. I'm not too bothered about the load hit on the Nagios server (It's probably over-speced for what it does, it's never been over 10% CPU), but we run each remote check every 30 seconds and each server has 5 different checks performed. I assume SSH requires more resources for each check but is there a huge difference? (I.E. enough of a difference to warrant the switch to NRPE). If it's any help, we monitor a mix of physical servers (Normally with 8, 12 or 16 physical cores) and Amazon EC2 medium/large instances.

    Read the article

  • Configuring network entirely VMware Workstation

    - by MRB
    Hello everyone! You could help me how to configure a network entirely virtual with VMWare Workstation 6.5 which has the Windows Server 2003 and XP workstations, but all virtual server and workstation windows xp.Outra thing is through my Windows Server 2003 I will release Internet access for Windows workstations xp.Everyone I'd like to simulate at home as if in a company but everything virtual. My host is a Windows XP thanks!

    Read the article

  • Problems restoring old backups in NetBackup 6.5

    - by gharper
    I had a server that was decommissioned & replaced last year, and since the server was no longer in use, I deleted it's client & backup policy from the NetBackup Admin Console shortly afterwards. I recently got a request to restore a file from the old server, however when I specify the source client for the restore, I get an error message saying: WARNING: server (backupserver) does not contain any backups for client (oldserver) using the specified policy type (Standard) as requested by client (backupserver). [Ok] In addition to that error, I can't seem to run a Client Backup report on the old client any more to determine what tapes I need to recall in order to re-index and restore the files... My questions: Does deleting the client somehow remove NetBackups ability to ever restore files from the old system, even if the backups have a retention period of infinity? Is there a way to restore the file from the tape, assuming I can figure out which tape I need?

    Read the article

  • How to add a new attribute to an existing LDAP objectclass?

    - by David R.
    I created a custom LDAP objectClass, but forgot a couple attributes before I added it to my OpenLDAP server. I followed the instructions on this Ubuntu doc page: https://help.ubuntu.com/12.04/serverguide/openldap-server.html I am running Ubuntu 12.04. So, how do I add a new MAY attribute to an objectClass that is already applied to the server? Specifically on OpenLDAP, but it would be good to know how for Novell eDirectory as well.

    Read the article

  • Rewrite /folder to / Using .htaccess

    - by manyxcxi
    I am trying to redirect /folder to / using .htaccess but all am I getting is the Apache HTTP Server Test Page. My root directory looks like this: / .htaccess -/folder -/folder2 -/folder3 My .htaccess looks like this: RewriteEngine On RewriteCond %{REQUEST_URI} !^/folder/ RewriteRule (.*) /folder/$1 What am I doing wrong? I checked my httpd.conf (I'm running Centos) and the mod_rewrite library is being loaded. As a side note, my server is not a www server, it's simply a virtual machine so it's hostname is centosvm.

    Read the article

  • Virtual hosts and subdomains, need configuring on live, not on dev

    - by rix
    I have a query about subdomains and virtual hosts. On my dev server, I ca nset up a new virtual hosts and point it to a subdomain, ie: newdomain.mydevserver.com All is fine and I can access 'newdomain/mydevserver/com' I can also do 'host newdomain.mydevserver.com' However, when I do the same with my main server I get the server couldn't be contacted error - I'm guessing that's because i need a cname or a record for the DNS. My question is, why does it seem that i can create subdomains on my dev but not on my live server? Help appreciated, many thanks!

    Read the article

  • How long are the default times for greylisting? [on hold]

    - by rubo77
    In Wikipedia it sais: A mail transfer agent (MTA) using greylisting will "temporarily reject" any email from a sender it does not recognize. If the mail is legitimate the originating server will, after a delay, try again and, if sufficient time has elapsed, the email will be accepted. But how can I find out how long these delays are on my server and on the receiving side? My goal is to speed up email-traffic with partners using greylisting too and speed up the receiving of the first email someone sends to customers on my server.

    Read the article

  • Apache url rewrite to Nginx

    - by Kaloyan
    i work on a little php platform and my server is nginx. The first version of this php site was developed for Apache server. I need to upgrade the site and to migrate it to nginx server. The problem is url rewriting. I have this simple url rewrite rules in my Apache server: RewriteEngine On RewriteBase /simple-php/ RewriteCond %{REQUEST_FILENAME} !-d [NC] RewriteCond %{REQUEST_FILENAME} !-f [NC] RewriteRule ^(.*)$ viewpost.php?id=$1 [QSA,L] I can't "translate" this to nginx rewrite syntax. Can anybody help me? P.S. I can read both documentations, but i have not this time, just need fast solution. Thanks!

    Read the article

  • ssh hangs on "Last login" line

    - by Pavel H
    This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

    Read the article

  • FreeBSD: problem with Postfix after updating LDAP

    - by Olexandr
    At the server I installed openldap-server, at this computer open-ldap client has already been installed. Version of openldap-client (2.4.16) was older then new openldap-server (2.4.21) and the version of client has updated too. OpenLDAP-client works with postfix on this server and after all updates postfix cann't start again. The error when postfix stop|start is: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix" At the category with libraries is libldap-2.4.so.7, but libldap-2.4.so.6 is removed from the server. When I want to deinstall curently version of openldap-client, system write ===> Deinstalling for net/openldap24-client O.K., but when I start "make install" system write: ===> Installing for openldap-sasl-client-2.4.23 ===> openldap-sasl-client-2.4.23 depends on shared library: sasl2.2 - found ===> Generating temporary packing list ===> Checking if net/openldap24-client already installed ===> An older version of net/openldap24-client is already installed (openldap-client-2.4.21) You may wish to ``make deinstall'' and install this port again by ``make reinstall'' to upgrade it properly. If you really wish to overwrite the old port of net/openldap24-client without deleting it first, set the variable "FORCE_PKG_REGISTER" in your environment or the "make install" command line. *** Error code 1 Stop in /usr/ports/net/openldap24-client. *** Error code 1 Stop in /usr/ports/net/openldap24-client. Updating of ports doesn't help, and postfix writes error: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix"

    Read the article

  • Can a FreePBX backup be restored to a different version?

    - by Tim Long
    I run a small PBX based on the FreePBX distro of Asterisk. The installation has been steadily upgraded but for various reasons, we want to start again on a new server with a clean install from the distribution media. Will I be able to take a backup from the old server and restore it to the new server, even though the installs are different versions? How sensitive are FreePBX backups to the build version? Is it possible to get at least a partial restore?

    Read the article

  • Private Git repo using Smart HTTP with LDAP authentification

    - by ALOToverflow
    I've been crawling the interwebz and getting my hands dirty for the last few days, but I can't seem to make it all work together. I managed to get a HTTP repo working with Ubuntu 10.04 over Smart HTTP (pull and push over HTTP) for a single repo. This means that I do the initial setup over SSH to the server (git init --bare) and after that the clients can pull and push to it (git clone http://servername/allgitrepos/repo.git). Unfortunately it's impossible to add a new repo without SSHing to the server and adding it manually) i.e. git push http://servername/allgitrepos/repo2.git (allgitrepos is available for everyone to read-write and execute) would fail talking about git update-server-info (which seems to be a general error message). So far the repository is anonymous, so I would like to authenticate using LDAP and also use the LDAP creds to make the git commit. So, how can I push new repos to the server and how can I use the LDAP creds to make the git commit. Thanks

    Read the article

  • Servers/Websites Keep Going Down

    - by Tyler Johnson
    Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

    Read the article

  • IT merger - self-sufficient site with domain controller VS thin clients outpost with access to termi

    - by imagodei
    SITUATION: A larger company acquires a smaller one. IT infrastructure has to be merged. There are no immediate plans to change the current size or role of the smaller company - the offices and production remain. It has a Win 2003 SBS domain server, Win 2000 file server, linux server for SVN and internal Wikipedia, 2 or 3 production machines, LTO backup solution. The servers are approx. 5 years old. Cisco network equippment (switches, wireless, ASA). Mail solution is a hosted Exchange. There are approx. 35 desktops and laptops in the company. IT infrastructure unification: There are 2 IT merging proposals. 1.) Replacing old servers, installing Win Server 2008 domain controller, and setting up either subdomain or domain trust to a larger company. File server and other servers remain local and synchronization should be set up to a centralized location in larger company. Similary with the backup - it remains local and if needed it should be replicated to a centralized location. Licensing is managed by smaller company. 2.) All servers are moved to a centralized location in larger company. As many desktop machines as possible are replaced by thin clients. The actual machines are virtualized and hosted by Terminal server at the same central location. Citrix solutions will be used. Only router and site-2-site VPN connection remain at the smaller company. Backup internet line to insure near 100% availability is needed. Licensing is mainly managed by larger company. Only specialized software for PCs that will not be virtualized is managed by smaller company. I'd like to ask you to discuss both solutions a bit. In your opinion, which is better from the operational point of view? Which is more reliable, cheaper in the long run? Easier to manage from the system administrator's point of view? Easier on the budget and easier to maintain from IT department's point of view? Does anybody have any experience with the second option and how does it perform in production environment? Pros and cons of both? Your input will be of great significance to me. Thank you very much!

    Read the article

  • Jailkit not locking down SFTP, working for SSH

    - by doublesharp
    I installed jailkit on my CentOS 5.8 server, and configured it according to the online guides that I found. These are the commands that were executed as root: mkdir /var/jail jk_init -j /var/jail extshellplusnet jk_init -j /var/jail sftp adduser testuser; passwd testuser jk_jailuser -j /var/jail testuser I then edited /var/jail/etc/passwd to change the login shell for testuser to be /bin/bash to give them access to a full bash shell via SSH. Next I edited /var/jail/etc/jailkit/jk_lsh.ini to look like the following (not sure if this is correct) [testuser] paths= /usr/bin, /usr/lib/ executables= /usr/bin/scp, /usr/lib/openssh/sftp-server, /usr/bin/sftp The testuser is able to connect via SSH and is limited to only view the chroot jail directory, and is also able to log in via SFTP, however the entire file system is visible and can be traversed. SSH Output: > ssh testuser@server Password: Last login: Sat Oct 20 03:26:19 2012 from x.x.x.x bash-3.2$ pwd /home/testuser SFTP Output: > sftp testuser@server Password: Connected to server. sftp> pwd Remote working directory: /var/jail/home/testuser What can be done to lock down SFTP access to the jail? FWIW, I mostly used this as a guide: http://digitalpatch.blogspot.com.ar/2010/03/openssh-daemon-hardening-part-3-setup.html

    Read the article

  • Kerberos authentication between 2 applications

    - by Spivi
    We work on a server 2003 and server 2008 R2 enviroment. I'm familiar with the basic usage of the Kerberos protocol where the protocol authenticates a client when he tries to use a shared resource (server, folder, printer, etc.). We have three distinct and independent .NET applications that we develop inhouse (app A, app B & app C) but they need to communicate for a given reason (A recieves messages only from B and C and C recieves messages only from B). Is it possible to configure the Kerberos services to authenticate messages/request between two .NET apps ? (Instead of a user-server authentication, we will have an application-application authentication)

    Read the article

  • Cloning a VM to add a new MySQL Slave

    - by Ben Holness
    I am in the process of adding a new slave to a replicated mysql setup. All of the slave nodes are virtual machines. If I clone one of the nodes to a new VM, then start it with no networking, stop mysql, change the server-id in my.cnf to a new id and then restart mysql and networking, will it all work correctly, or will mysql get confused because it used to be a different server id? OS: Ubuntu 10.10 VM Platform: VMWare 5 MySQL : Server version: 5.1.49-1ubuntu8.1-log (Ubuntu)

    Read the article

  • Win 7 Remote Desktop connection failure when already logged in.

    - by Andy E
    I have a bit of a strange problem, magnified recently by my broadband dropouts. I wasn't sure whether to post this on SU or SF, so I thought I'd start here as more users would be likely to know what the problem is. In short, when I try and connect to my server (Windows Server 2008) from my laptop running Windows 7, I can only connect if my remote account was previously logged out. If I'm still logged in I get the error message: Windows cannot connect to the remote server. No explanation or anything. If my IP address is the same, I don't have this problem. If I boot up Windows XP Mode and run XP's remote desktop connection it works just fine -- I think the difference there is it takes me to the remote server's logon screen. With Win 7 RDC you never see the logon screen, it asks you for credentials before entering full screen mode. The real problem is that I'm having random broadband dropouts and my IP isn't static. If I logon via Win XP RDC, log out and then run Win 7 RDC then it works fine. I realize I can just use Win XP's RDC for now, but I don't really like keeping XP Mode open if I can help it. Does anyone know a way around this problem? Maybe forcing Win 7 RDC to go to the logon screen, or changing some server-side settings to work around the IP address issue?

    Read the article

  • Scaling a LAMP website hosted on EC2

    - by Gublooo
    Hello, I'm very new to all this - I've recently managed to launch my website on EC2. As next step, I want to learn how to scale the website. I have a general idea but wanted some input from the experts about how to go about it. My website is based on LAMP but also has Red5 server which allows users to record messages and also used for playing them back. Currently this is the architecture I'm planning to setup for initial scaling. Deploy four small EC2 instances for the following purposes: Instance-1: On this instance I will run the MySql database Instance-2: On this instance I will run the red5 server Instance-3 & Instance-4 These 2 instances will be used to deploy the website and will have Apache running on them. They will communicate with the mysql server on Instance-1 and red5 server on Instance-2 using the internal IP address. As an when required, I will launch another instance of the same EBS - I will have EBS of say 50 GIG where all the mysql data will be stored. Also red5 will use this EBS to store the video messages Load-Balancer - Use the load balancer provided by Amazon to load balance Instance-3 and Instance-4 This is what I have in mind. I could be way off so please bear with me. Also I have not taken into account the case of scaling MySql server as I currently have no idea about how that will be done and whether or not it is necessary initially. I am aware that Amazon provides auto scaling and mysql scaling as well but I dont want to get into that right now. Your feedback is appreciated Thanks

    Read the article

  • apt-get commands pausing at 'Waiting for headers'

    - by Matt
    I have a VM running Ubuntu Server 9.10 running a basic web server setup. Whenever I run an apt function it will pause for around 1 minute at 'Waiting for headers...'. It will eventually clear through and continue as normal but it is a bit of an annoyance. Everything else on the server seems to run fine. Any ideas?

    Read the article

  • BIND: forward 1st level zone

    - by raven
    First of all: sorry for the language, English is not my primary language. I have star-like DNS structure with many filials (more that 2): ^ | v filialNS_1.filial_1.city.local <---- ns.main.city.local <---- filialNS_2.filial_2.city.local ^ | v ns.mail.city.local is slave of all filials zones filialNS_1 is master of filial_1.city.local filialNS_2 is master of filial_2.city.local filialNS_N is master of filial_N.city.local I want to: serve DNS queries for xxx.filial_N.city.local with filialNS_N.filial_N.city.local forward all queries for xxx.xxx.xxx.local from filialNS_N to ns.main.city.local forward other queries to our provider's DNS on filial (or google-public-dns or anything else) FILIAL CONFIG named.conf zone "filial_1.city.local" { type master; file "/etc/namedb/dynamic/filial_1.city.local"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "2.76.10.in-addr.arpa" { type master; file "/etc/namedb/dynamic/2.76.10.in-addr.arpa"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "local." { type forward; forward only; forwarders { <ns.main.city.local IP address> }; }; nslookup server.filial_1.city.local - works fine nslookup server.main.city.local Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find server.main.city.local: NXDOMAIN Where am I going wrong?

    Read the article

  • Is it possible to use bittorrent for a fileserver

    - by sris
    I would like to set up a file server that is searchable, preferable via the web. I'm wondering if it would be possible to achieve this using the bittorrent protocol and have a single client sharing every single torrent on the server. I guess I could use some available tracker solution for the webinterface or write one myself. My concerns are the if there are any limits to the number of torrents a single client can share since this may potentially be 10k torrents. The number of downloading clients is very small, only myself and my relatives. The idea is to have a single place to host everything from vacation photos to musical creations. Is there any other options for this kind of file server. It should also be easy to upload files to the server.

    Read the article

  • Forward request through IPTables

    - by Jeremy
    I have a server running CentOS with 50 IP addresses on it. I was looking to use it as a proxy server (not just HTTP), but can't find any examples on how to set up the IP Tables. I want to proxy into IP-X and have my request look like its coming from IP-X. I currently do this on squid, but we need to proxy more than just HTTP traffic. Here is an example of the squid config: acl users src 255.255.255.255 #Locked down IP address acl all src 0.0.0.0/0.0.0.0 # http access rules http_access deny !users http_access allow users http_reply_access deny !users http_reply_access allow users icp_access deny all #ip_addresses acl ip3 myip 10.1.1.3 tcp_outgoing_address 10.1.1.3 ip3 Do to IP restrictions I need access to IMAP, POP and SMTP through a proxy. I want to use the server I already pay for that has 50 IPs on it as the proxy server.

    Read the article

< Previous Page | 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118  | Next Page >