Search Results

Search found 30252 results on 1211 pages for 'network programming'.

Page 1115/1211 | < Previous Page | 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122  | Next Page >

• Problem with connecting two different networks

  - by tanascius

  I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

  Read the article

• apache/httpd responds slower under EL6.1 than EL5.6 (centos)

  - by daniel

  I've read through other threads on performance differences between RHEL6 and RHEL5, but none seem a tight match to mine. My issue manifests itself in slightly slower average response time (20ms) per request. I have about 10/10 servers of the same hardware spec with Cent6.1 and Cent5.6. The issue is consistent across the group. I am running Ruby on Rails with Passenger. Apache config is identical (checked out from the same SVN repo) Ruby and Passenger are identical builds. Application is identical and being served traffic round robin. mod_worker An interesting clue from server-status: The Cent6.1 servers have a steady 20-40 threads in the "Reading Request" state while the Cent5.6 servers have around 1. I'm graphing this so I can see it trend over time. I also have a bunch of much newer machines that are significantly faster and are running Cent6.1. They dust all the older machines in response time, but I can see they also have a steady 20-40 threads in the "Reading Request" state. This makes me believe I can get their response time down, if I can figure out what is holding up these requests. My gut is telling me that I need to tune some network setting in sysctl, but I haven't figured it out yet. Help is appreciated.

  Read the article

• Noob with git repository on Windows Storage Server 2008?

  - by HibbyHoo

  I have a Western Digital Sentinel at home running Windows Storage Server 2008 R2 Essentials. I have several git repositories on it for my own personal projects, and have no problem pushing and pulling over my local network. I want to be able to access those repos remotely from anywhere. I am able to log in and remotely access folders and files on it, but I cannot clone repos using the same address. It hangs for a REALLY long time before finally failing with an error: git.exe clone --progress -v "https://myIpAddressHere/Remote/fs/files.aspx?path=%5C%5Cmydevicename%5Cmyreposfolder%5Cmyrepo.git" "D:\repo" Cloning into 'D:\repo'... error: Failed connect to myIpAddress:443; No error while accessing https://myIpAddress/Remote/fs/files.aspx?path=%5C%5Cmydevicename%5Cmyreposfolder%5Cmyrepo.git/info/refs fatal: HTTP request failed git did not exit cleanly (exit code 128) I'm not too privy to networking or web development, and I have only a rudimentary understanding of how to use git (with TortoiseGit). I'm having a hard time finding search results for this specific problem and a hard time interpreting generic tutorials for the general scope of this problem. TortoiseGit version: 1.7.13.0. git version: 1.7.10.mysysgit.1.

  Read the article

• Intranet machines refuse to talk anymore

  - by ashes999

  I have two machines on the local intranet. They used to be able to talk to each other (ping, share files, etc.). Both are not successfully connected to the internet. The problem machine (lets call it test machine) can't talk to my main machine. The test machine can ping other machines on the intranet (at least one of my coworkers), but not mine. Odd. When I try to ping it from my machine, by machine name, I get Destination host unreachable. Both machines are on the intranet, with the network configured as Work Both machines have Windows Firewall disabled temporarily Both machines can talk to the internet (Google, SO, etc.) Neither machine can ping the other I need help resolving this. What I really want to achieve, is to remote into the test machine from my main machine, like I used to be able to do a few weeks ago. Some notes: Tried arp -a on both machines. I don't see the other machine's IP listed. Both machines have stable IPs; neither seems to have an IP conflict The configuration under ipconfig /all on my main machine mathces my coworker's machine. The test machine can ping his machine, but not my machine. The target machine times out trying to ping the main machine; the main machine gives me Destination host unreachable. I have rebooted both machines (several times) to no avail I have /release and /renewed both machines several times

  Read the article

• Bind9 not doing anything with forwarded query responses?

  - by Rykaro

  I have a Bind DNS server that is the local production DNS server and a Windows 2008 R2 domain controller which provides DNS for a lab environment with the domain xyz.lab. I've configured the Bind DNS to forward DNS requests for the domain xyz.lab to the Windows DNS server with this config: zone "xyz.lab" { type forward; forward only; forwarders { x.x.x.x; }; }; zone "x.x.x.in-addr.arpa" { type forward; forward only; forwarders { x.x.x.x; }; }; And Bind options are (the all_internal acl includes the subnets of both the production and lab networks as well as the loopback of the bind server): allow-query { all_internal; }; allow-recursion { all_internal; }; allow-transfer { none; }; notify no; minimal-responses yes; version "unknown"; Unfortunately, when I do an nslookup or dig on the bind server for a host on the lab domain, the request times out. The logs on the Windows 2008 DNS server show it receiving the query and responding to it and a network packet trace shows the query responses arriving at the Bind DNS server. The servers reside on the same switch with a router providing connectivity between the layer 3 subnets (production and lab are on different subnets) and there is a round trip time of between 3ms and 5ms on pings between the two servers, so I don't think there is an issue with latency causing a timeout of the query. In summary a query-response arrives back at the Bind server and the nslookup/dig times-out. Why does the Bind DNS not seem to be doing anything with the query responses when it receives them?

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

• No access to Windows 2003 admin shares

  - by ARomo

  This is the environment: Several Win 2003 SP 2 servers and several Win XP SP2 & SP3 clients. All in the same LAN. Firewall is disabled everywhere. No recent Windows updates or configuration changes. This is the problem: Since last Thursday, I log on to any other server or workstation as any regular (non-admin) user and I fail to be able to open ADMIN SHARES ONLY (namely \\server1\c$, \\server1\e$ and \\server1\admin$). The error message is: "\server1\c$ is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Multiple connections to a server or shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again." I can, however, open the same shares if I use FQDN or IP address: \\server1.domain.local\c$ \\172.0.0.1\c$ Other shares do not have this issue and I can open them without any issue. Any ideas or suggestion would be truly appreciated. Thank you in advance.

  Read the article

• How can I make AdobePS recognize my printer in Win98se?

  - by Jeff

  I am trying to use the adobe product: "PostScript Printer Driver AdobePS 4.2.6 for Windows 95 and Windows 98" to connect a new HP laser printer (CP1025nw) via USB to a machine running win98SE. I am using the PPD file for "HP color LaserJet PS". The Adobe utility installs the printer, and it shows up on the printer list ... but it doesn't print. I get an error message (sometimes) that an error occurred writing to USB001.. Evidently, AdobePS cannot "See" the printer. I suspect there is a problem wrt the printer port. Nothing I pick works. I have two virtual printer ports, USB001 and USB002 which were created during the installation of an HP inkjet printer. The inkjet will work on either of these, but the laser printer works on neither. When I connect the laserjet printer, the windows New Hardware Wizard activates, but I don't see how to point it at the AdobePS Postscript driver. HP has no support whatsoever for win98, so there's no hope of getting help from them. The printer works great with the several winXP computers connected through either the network connection or the USB. So, how do I convince Win98se to use the adobe postscript printer driver? Is this printer even a postscript printer? Is there a better way to get win98se to talk to this printer? Any suggestions?

  Read the article

• Clean installation of RHEL 5.5 claims package "desktops" is missing

  - by TKguru42

  Hi all, I'm a student worker in the CS department of my university, so please forgive me for any unprofessional descriptions. Simplified explanations are appreciated. I recently replaced some bad graphics cards in a few public workstations. The machines are all the same model. Before putting them back on the network I did fresh installs of RHEL---first I tried 5.4, but yum update ran into all sorts of ugly dependency errors and if I tried to remove any of the problematic packages, the whole operating system FUBAR'd. Using RHEL 5.5 gave me the same errors during install saying that "java.1.5.1-sun*" and "desktops" were missing, but yum update didn't have any dependency problems. Now that I tried logging in through the GUI, I encounter no GUI past the standard RHEL login page. The desktop is a uniform light teal and there's no system tray. An xclock window and an xterm window are open, and Firefox opens automatically, but that's it. Nothing else. What's REALLY confusing is that the computer claims that gnome is already installed, except it clearly isn't working. Any help or advice is greatly appreciated. If it helps, our department uses kickstart to run our standard Linux installs. I can try to get the script if that would be of use. Thank you!

  Read the article

• Setup Apache with IPv6

  - by mrz

  I have two virtual machine on my computer. I have Apache installed on one of them (would be referred to as "server" after this), and I have set the Apache to listen to an IPv6. And when I enter the IPv6 into web browser on the "server" I see my index.html file. so far so good ... I want to be able to open a web browser on the other virtual machine("client") and see the index.html. But, when I try entering the IPv6 of the "server" in a web browser on the "client" I get an Unable to establish a connection to the server error. I can ping6 "client" from "server" and vice verse. There is only one thing to mention. ifconfig of the "server" shows 3 different IPv6 which two of them are scoped Global and there is one Link scope IPv6. On the "client" there is only one Link scope IPv6 though. I only can ping the Link IPv6s. Pinging other IPv6s would result connect:Network is unreachable. And if I set Apache to listen to Link IPv6, The rcapache2 start will fail the job. Any thoughts on what I am probably missing/doing wrong?

  Read the article

• 2 Web Servers, 2 Domains, 1 WAN IP configuration

  - by Tillman32

  The Problem: I have 2 domains, 2 web servers, 1 WAN IP. This is on a home network, so I don't have any crazy router or anything with the right tools, at least I don't think I do. I have a Dlink DIR-655 router. I need to be able to forward the website to the right box. 1 server is hosting www.site1.com, and the other should be hosting, www.site2.com. I forwarded the domain, to a port that is forwarded to that box. wanip:1235, 1235 is then forwarded to the internal IP of site2's server. But when I go to www.site2.com I get the 404 page of www.site1.com. I need www.site2.com to go to the right server. Is this something I can do in the virtual hosts of www.site1.com or is it something else. Also, if this isn't entirely possible, or if its a big process, I can just move www.site1.com to the www.site2.com's server, and use virtual hosts, that is an option that I would be okay with.

  Read the article

• Unable to connect to SQL Database (can the password be reset)

  - by user45450

  I have recently joined a company which has an SQL 2005 Server running a few databases. The server looks like no one has touched it in a couple of years and has this week it ran out of disk space. After a quick hard drive scan it looks like some of the databases have become a little bloated and particularly the Sharepoint_config~*~_log and WSS_Content_log.ldf have grown to about 15GB. I have been able to log into a couple of the other databases and use the shrinkfile command to free up disk space but for some reason I am unable to log into the sharepoint and Microsoft#SSEE databases (which gives me the "cannot connect to Sharepoint, a network related or instance specific error occurred..." when I try and connect) I can see that the database is running via the SQL surface configuration and I have made sure that the remote connection settings allow me to connect locally but I am still unable to log in either with windows authentication or locally. Is there any way to reset or recover the database login details so I can get in? ( I have tried logging in with all the administrative passwords I can find and after tracking down the company who installed it in the first place I found out that they have no idea what the password could have been)

  Read the article

• .lnk doesn't open, no errors

  - by MushinNoShin

  I have a shortcut (.LNK) on my desktop to a MS Access database out on a network drive. When I double click that shortcut I get an hour glass for about 10 seconds and then nothing. No errors, no access opening, nothing happens. It appears as if there's not even an MSAccess process running in the background. The file successfully opens from: The Open dialog in Access The commandline "C:\path\to\MSACCESS.EXE C:\path\to\shortcut.lnk" The commandline "C:\path\to\MSACCESS.EXE C:\path\to\whatTheShortcutPointsTo.mdb" The file silently fails to open from: Double clicking the shortcut.lnk Double clicking the mdb file that shortcut.lnk targets At first I thought it had to do with how the link handler operated but the fact that it does the same exact thing when I try to open the mdb directly in explorer makes me think it's an issue with explorer. I've tried restoring, deleting, and recreating the association with the extension. I've tried running MSACCESS.EXE /regserver. I've run out of things to throw at it. In case this is specific to MS Access 2007; I'm trying to use 2007 :)

  Read the article

• Windows Server 2003 (w/Exchange) move to new machine

  - by James Booker

  I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

  Read the article

• Using a second Wifi Router (in order to use a LAN port)

  - by Sledge81

  Problem: Connecting a TV decoder via Internet. It doesn't have inbuilt wifi so wired LAN is the only option. I bought a second Wifi Router so I could use its LAN port to create a wired internet connection to my decoder. What I want to achieve: The second Wifi Router should basically pick up the signal from the main wifi router. I would then use the LAN port to connect (with a wire) to the TV decoder. In other words have my secondary Wifi Router act as an access point, which will enable me to use a wired LAN connection to the decoder. What i've done so far: Connected the second Wifi Router to my laptop via the LAN ports. Access 192.168.1.1 and went into my second router. 1) SSID set to the same one as the main Wifi Router 2) Tried disabling DHCP and enabling DHCP (with the DNS and default gateway configured the same as the main router). When I check my network connections, I see the LAN connection too but it says 'Not connected to the internet' while the Wifi (main router) shows connected. Can someone please advise on how to use my second Wifi Router to connect to the main Wifi Router (and thus the Internet). Thanks. main wifi router: Zyxel secondary wifi router: TP Link

  Read the article

• ESX 3.5 refuses to update

  - by Speeddymon

  I have a set of ESX 3.5 servers in 2 different datacenters. One is DR, one is production. They are on the same vlan and so I can access any of them on the private network from my vCenter server. Last month, as a learning experience (I hadn't dealt with ESX much before), I updated the DR server. Other than finding out that a couple of bundles had to be installed manually in order to get the rest to install from vCenter, it went off without a hitch. Now, I'm trying to do the same for our production servers and it is not working. I've googled around for the error I get during scan, and investigate loads of different solutions (editing the integrity file, checking DNS, etc) -- I did install the 2 bundles that had to be installed manually already -- but scan from vCenter is just not working. Side note: I did just scan the DR server again and that scan works fine so shouldn't be a problem with vCenter that has cropped up recently -- it has to be something else. The error I get is: Patch metadata for (servername) missing. Please download updates metadata first. Failed to scan (servername) for updates. I'm all out of ideas on how to make this work, so any help would be hugely appreciated.

  Read the article

• Incorrect Internal DNS Resolution

  - by user167016

  I'm having a DNS issue. Server 2008 R2. The first clue was that after being off the network for a month, I could no longer Remote Desktop into my workstation by name, it wouldn't find it. Both via VPN and internally. But if I connect using its IP, that works. Now I notice in the server's Share and Storage Management, in Manage Sessions, it's displaying the incorrect computer name for some users. So I try, for one example: Ping -a 192.168.16.81 Pinging BOBS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: - replies all successful Then I try Ping RICHARDS_COMPUTER Pinging RICHARDS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: -all replies successful In DHCP, .81 belongs to RICHARDS_COMPUTER I did try flushdns. Not sure if this is related, apologies if it's not, but when I try to connect, I also get prompted: "The identity of the remote computer cannot be verified. Do you want to connect anyway? The remote computer could not be authenticated due to problems with its security certificate. It may be unsafe to proceed.." It then lists the correct name as the name in the certificate from the remote computer, but claims that the certificate is not from a trusted authority. Any thoughts are most appreciated!

  Read the article

• 3-4 old computers = general purpose cluster?

  - by TheLQ

  I have 3 old computers lying around right now running a P2 at 800 MHz(?), Intel Mobile 1.6 GHz, AMD Athlon XP 2000+ at 1.66 GHz, and (might not use this) P4 at 2.7 GHz, all with 512 MB Ram, and am considering clustering them together for fun/knowledge. They would be running an undecided version of linux, preferably ubuntu based. The issue is what I want to use it for: general computing and occasional video encoding. By general computing I mean day to day tasks. However I'm not sure if every program started by a single X session is going to exist on the same machine, defeating the purpose of such a system. Will programs be split up or exist on one machine? Second, assuming this is running 100baseT ethernet (not sure if the PCI slot itself could handle Gigabit), would the speed of having a program exist over the network be an issue? It seems that the constant asking of various things in RAM would be quite slow. And before you say "buy another computer!", that's not the point of this question. I'm asking would it be usable, not necessarily practical. And yes I know, this is going to be extreamly power consuming.

  Read the article

• OSX server setup suggestions

  - by Tom

  I am looking into the possibility to setup an OSX server for my employees, and would like some input on what is the best approach to meet my needs, and perhaps some suggestions if I am moving in the wrong direction. I am thinking of a Mac Mini OSX server, and are not sure if my needs will be met, and what possibilities are out there. I want these capabilities: - Groups/Users managed on server - Shared folders and private folders for users/groups - Access to activated services - Server hosting software for the users (developing tools ++) - Similar to Windows Terminal Server - Virtual desktop environment (both local and over internet/VPN) - Possible to access trough Mac and Windows The reason I am looking at OSX server is that my employees almost only work in OSX environment, and I want to offer the capabilities to logon to the server trough some kind of terminal software, and have full access to their work OSX environment and software on their mac or pc, from anywhere they might be. Instead of having to have multiple setups and need for spending alot of time installing and setting up needed software on every client. This is a small business, where some work on local network, and others from the internet, preferably trough VPN. But a terminal server solution, that are fast and easy to manage would be perfect for our needs. So if anyone have any experience with a similar setup, please let me know what you did, and your experiences with your setup.

  Read the article

• IPtables and Remote Desktop with Proxy

  - by Sebastian

  So I setup a windows 2008 web server R2 on VirtualBox. Currently using Bridged Network. I can remote desktop to the machine hosting the VM (10.0.0.183) but cannot remote desktop to the VM itself (10.0.0.195). The remote port on the VM set to 5003. VM setup to accept remote connections (windows side). We also use a proxy for our internet, and I added these rules under NAT. (centOS 5) on our proxy box. -A INPUT -p tcp --dport 3389 -j ACCEPT -A REROUTING -i ppp0 -p tcp --dport 3389 -j REDIRECT --to-port 5003 -A FORWARD -d 10.0.0.195 --dport 5003 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT I've been trying for hours and hours and just cannot get it to work. I also used freedns so that we can use a domain name to connect too this VM over the internet. (the DNS points to our external IP address). If we don't get this right we will have to purchase a PPoE from an ISP to connect to this VM remotely, but I know that there is an alternative route if I can just get this port forwarding right!

  Read the article

• Troubleshooting DTCPing Errors

  - by JimmyP

  So I am running DTC ping between 2 machines on our network and am getting the following error ++++++++++++++++++++++++++++++++++++++++++++++ DTCping 1.9 Report for WEB2 ++++++++++++++++++++++++++++++++++++++++++++++ RPC server is ready ++++++++++++Validating Remote Computer Name++++++++++++ 03-03, 13:39:45.099-->Start DTC connection test Name Resolution: internal-->10.20.3.236-->internal.something 03-03, 13:39:45.114-->Start RPC test (WEB2-->internal) Problem:fail to invoke remote RPC method Error(0x6BA) at dtcping.cpp @303 -->RPC pinging exception -->1722(The RPC server is unavailable.) RPC test failed I have also run RPC ping where I get what I beleive is the same error: C:\Program Files\Windows Resource Kits\Tools>rpcping -s internal Exception 1722 (0x000006BA) Number of records is: 4 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1722 Detection location is 323 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1237 Detection location is 313 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 311 Flags is 0 NumberOfParameters is 3 Long val: 135 Pointer val: 0 Pointer val: 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 318 Flags is 0 NumberOfParameters is 0 I'm pretty sure that the exception number 1722 is the key but I can't find any info about it. There may be a firewall with ports that need opening between the machines which I am checking with our sys admins now. But I can do a regular ping between the machines. Other than that I am reading a lot of articles talking about OS services and components I know nothing about and am having trouble finding any info on. Can anyone shed any light on this? FYI the machine is running Windows Server 2003 RS SP2.

  Read the article

• How many iptables block rules is too many

  - by mhost

  We have a server with a Quad-Core AMD Opteron Processor 2378. It acts as our firewall for several servers. I've been asked to block all IPs from China. In a separate network, we have some small VPS machines (256MB and 512MB). I've been asked to block china on those VPS's as well. I've looked online and found lists which requires 4500 block rules. My question is will putting in all 4500 rules be a problem? I know iptables can handle far more rules than that, what I am concerned about is since these are blocks that I don't want to have access to any port, I need to put these rules before any allow. This means all legitimate traffic needs to be compared to all those rules before getting through. Will the traffic be noticeably slower after implementing this? Will those small VPS's be able to handle processing that many rules for every new packet (I'll put an established allow before the blocks)? My question is not How many rules can iptables support?, its about the effect that these rules will have on load and speed. Thanks.

  Read the article

• How to backup Servers to an SSH-Host with low traffic and access to versions and encryption?

  - by leto

  Hello, I've not run backups for the past dont't remember anymore years for my personal stuff until waking up lately and realising contrary to my prior belief: Actually. I care! :) Now I have a central data server at home where I want to attach an external media to, to which I want to save backups of my most important stuff, like years of self-written scripts, database dumps, you name it. I've tinkered with rsync+ssh over the last two years, also tried tar over ssh, but don't know the simplest and most easy to maintain way to do it yet. Heres my workload: A typical LAMP-Server (<5GB Data) which I'd like to backup fully so lots of small files connected via 10Mbit My personal stuff (<750GB Data) from a Mac connected via GE My passwords in an encrypted container (100Mb) from OpenBSD connected via serial-PPP My E-Mail from the last ten years (<25GB) as Maildir which I need to keep in readable format Some archives (tar.*) which I need to backup only once and keep in readable format (Deleted my ideas, as I'm here for suggestions) What I need: 1. Use an ssh-tunnel for data transfer 2. Be quick with lots of small files 3. Keep revisions 4. Be sure the data I save is not corrupted 5. Intelligent resume functions and be able to deal with network congestion :) 6. Compressed and optionally encrypted storage 7. Be able to extract data from backup easily (filesystem like usage would be nice) How would and with what software would you backup this stuff? Hints to tools that can help solve only part of my problem (like encryption) also greatly appreciated. Greets

  Read the article

• Folder Sharing NTFS permissions with Share Permission

  - by Muhammad Adly

  i have a problem on my domain, the history starting from when i had a server with WIN 2008 r2 installed with the following roles installed on it (AD, DNS, DHCP, File). From 1 month i decided to install a new server 2008 r2 server to get (AD, DNS, DHCP) and leave the file server on the old one. i did the following exactly: 1) robocopy all my data on external HDD 2) Install a new server with 2008 r2 3) transfer all 5 roles to transfer the domain to the new server (MainDC) 4) issue (NETLOGON, SYSVOL) not transferred but i decided to reinitialize them again an now they are operating (MainDC) 5) re-create and re-configure a new GPOs and link it to my OUs 6) reinstall Old server operating system with a fresh installation of WIN 2008 R2 (FileServer) 7) join my domain with my domain credentials. the issue when i tried to share folder on \fileserver the permissions that i had set in sharing permissions are applied on the main shared folder and subfolders. the security settings are not applied. i.e. Say i'm sharing \fileserver\MainFolder with sharing permission for Authenticated Users that can read, so every one can read this main shared folder, if i set security permission for \fileserver\MainFolder\User1 that User1 can Read\Write\Modify. User1 can not perform this processes when accessing it from Network Share, i tried alot of steps from topics online get ownership for folder, remove inheritance from parent folder, applying changes for child objects, i tried also to construct a new folder structure but also the same issue, i tried another host PC, also i get the same issue.

  Read the article

• Get more space for redis in unix server

  - by DevTraveler

  In our app we have only windows servers beside the cases we use redis queues. This case , we use unix server created by amazon. As you can see we do not have a lot of space available and we want to make sure redis has enough space to work without getting stuck. I am little bit new in unix and after reading some data about the unix file system i still was not fully sure how can i give the redis drive (it is in the home directory) more space. I see the mnt that has a lot of space but read it is temporary for cd-rom and network drives. Can you help me figure out how to get more space to my redis ? If it is possible i prefer not to re-install the redis server. Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.7G 880M 89% / udev 7.4G 4.0K 7.4G 1% /dev tmpfs 3.0G 152K 3.0G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.4G 0 7.4G 0% /run/shm /dev/xvdb 414G 30G 364G 8% /mnt Thanks.

  Read the article

< Previous Page | 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122  | Next Page >