Search Results

Search found 5123 results on 205 pages for 'gateway timeout'.

Page 114/205 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

  • ignore ipv6 router advertisements for static addresses with bonded interfaces

    - by boran
    I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

    Read the article

  • configure cisco catalyst 3560g with an egress uplink

    - by imaginative
    Currently my setup has our egress uplink connected directly to an external interface on a linux router/firewall/nat gateway. Since the linux box is a single point of failure, I've since setup two openbsd boxes using carp+pf+pfsync in order to gain some additional redundancy. the problem is, I only have one egress uplink (it's still a single point of failure) but need to get it to speak to the active carp node in my openbsd cluster which will server as my new router/firewall/nat cluster. Is there anything specific I need to do on a 3560G in order for me to be able to: 1) Drop the egress uplink into a port 2) Drop one link from the switch to a firewall 2) Drop a second link from a switch to the firewall This is so if one box dies, the other still has the egress link to the switch. Is putting them into one VLAN enough? Anything else that needs to go into the configuration for this setup to work?

    Read the article

  • Fedora14 serial console how-to needed

    - by lamba2
    Has anyone ever got a serial console working in fedora 14 ? Is it as simple as adding to grub: serial --unit=0 --speed=38400 terminal --timeout=10 serial console and add to the kernel lines: console=tty0 console=ttyS0,38400 ??? If so, this isn't working for me. I have agetty installed, and im using minicom, although i've heard you can also use "screen /dev/ttyUSB0" on the client side. The /etc/init/serial.conf file suggests it should be working, but nothing. Currently getting no joy from any of this after 2 days. Does anyone know a method that definitely works on fedora 14 ? (no /etc/event.d/ needed or such) edit: Client side im using a null modem cable and usb-serial adaptor.

    Read the article

  • limit linux background flush (dirty pages)

    - by korkman
    Background flushing in linux happens when either too much written data is pending (adjustable via /proc/sys/vm/dirty_background_ratio) or a timeout for pending writes is reached (/proc/sys/vm/dirty_expire_centisecs). Unless another limit is being hit (/proc/sys/vm/dirty_ratio), more written data may be cached. Further writes will block. In theory, this should create a background process writing out dirty pages without disturbing other processes. In practice, it does disturb any process doing uncached reading or synchronous writing. Badly. This is because the background flush actually writes at 100% device speed and any other device requests at this time will be delayed (because all queues and write-caches on the road are filled). Is there any way to limit the amount of requests per second the flushing process performs, or otherwise effectively prioritize other device I/O?

    Read the article

  • ISP Load Balancing with ISA 2006

    - by Bill Best
    I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

    Read the article

  • Problem with VPN using 2 Wire Router with a Linksys Router.

    - by Hiram Hubbard
    I am having a problem with a VPN between a 2 Wire router and a Linksys router. 2 wire is the client PC using Linksys Quick VPN software and Linksys RVS4000 is the server. The PC is not the issue. It works on a different network not using 2 wire. Also the Linksys RVS4000 is not the issue, 3 other user can VPN to it with no problem not using 2 Wire. The problem is with 2 Wire. The client PC is getting this error: "The remote gateway is not responding" What configuration changes are needed on the 2 Wire router (port, UPNP, etc...) and what changes are needed if any on the Linksys RVS4000? Thanks.

    Read the article

  • Permanent Routes Centos Questions

    - by user65053
    So with a little help I figured out how to setup these routes and I can set them in rc.local route add -net 208.82.236.0 netmask 255.255.255.0 dev ppp0 metric 1 route add -net 208.82.236.0 netmask 255.255.255.0 dev eth0 metric 10 my question is being that the first route is ppp0 as soon as I disconnect the modem the route is dropped how do I maintain the route or make it permanent so that next time the modem connects it will follow the route. Currently after ppp0 disconnects the route is dropped netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface laxapx03.o1.com * 255.255.255.255 UH 0 0 0 ppp0 208.82.236.0 * 255.255.255.0 U 0 0 0 eth0 10.0.1.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 default 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Migrate apache->tomcat to nginx->tomcat

    - by Slezhuk
    Now we are using apache2 as frontend, and tomcat as backend. We are using mod_proxy_balancer and AJP. Also we are using stickysession by JSESSIONID cookie: <Proxy balancer://backend> BalancerMember ajp://127.0.0.1:8008 min=10 max=100 ping=5 connectiontimeout=40 ttl=60 retry=20 route=node-1 BalancerMember ajp://127.0.0.1:8009 min=10 max=100 ping=5 connectiontimeout=40 ttl=60 retry=20 route=node-2 ProxySet lbmethod=byrequests timeout=30 ProxySet stickysession=JSESSIONID|jsessionid nofailover=Off </Proxy> and using jvmRoute parameter in web.xml to add tail to JSESSIONID cookie: <Engine name="Catalina" defaultHost="localhost" jvmRoute="node-1"> So far i did not found way to do this in nginx. Is there any solution for this? We are not using session replication, so getting sequential requests to same backend is crucial.

    Read the article

  • 2 routers, both DHCP, no IP assigned

    - by piobyz
    I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

    Read the article

  • Firewalling gateways and IDS's

    - by Scott Davies
    Hi, For IDS, I plan to have a Win 2008 server running on the gateway with the majority of roles disabled. I plan to firewall the Internet connection, but I'd also like to install Snort to work as an IDS. However, I am guessing that regardless of the Snort install of the promiscuous Winpcap driver, I won't be able to monitor ports that the firewall blocks. My thinking is that chain of flow is: Internet-Firewall on Win 2008-Winpcap-Snort-internal network Is there a way to still monitor services that the firewall will block (i.e. TCP 445 SMB) ? Perhaps run the data through Snort and then through the firewall ? Thanks

    Read the article

  • Weird routing problems with VPN

    - by Borek
    In our VPN setup I have to add a route to my routing table like this: route add 1.2.3.0 mask 255.255.255.0 172.16.1.1 -p Our internal addresses 1.2.3.x then use 172.16.1.1 as their gateway and both my local internet and work VPN can work at the same time. However, when I disconnect from VPN and reconnect again, I can't ping our servers even though the connection status is "Connected". When I do route print my previously added route is listed but it doesn't seem to work. So I try to execute that 'route add' command again and as expected, it tells me that The route addition failed: The object already exists. But - and that's the point - when I now try to ping our servers again, everything works! So every time, I have to execute this route add command that will fail but fix the issue at the same time. Any ideas what I might be doing wrong? My PC is Windows 7 x64, I am Administrator, UAC is enabled and the command prompt is run with elevated privileges.

    Read the article

  • Hyper-V virtual machine unable to get IP address from DHCP server running on same physical box

    - by Bronumski
    We have a Windows server 2008 R2 with two network cards running AD, DHCP, DNS and Hyper-V The first nic is setup with a static IP address and DHCP, WDS, and DNS are bound to it. The second nic is configured in Hyper-V to be only used by Hyper-V and has been automatically configured so that only the virtual switch is enabled on the adapter. DHCP and DNS work fine for all physical machines on the network. It also works for Virtual Machines running on another physical box. Virtual machines that are bound to the virtual switch network adapter are unable to get a IP address. If the virtual machine is given a static IP address with correct subnet, gateway and dns everything works. Has anyone else got this working?

    Read the article

  • Squid closing the connection on long HTTP GET requests

    - by Rhys
    Hello, When running a database query on a specific external site we use, Squid seems to cut off the connection after a consistent period of time (just over a minute). The query is submitted through a standard web form is that uses GET to query their database. Firefox 3 just displays a blank page. Internet Explorer throws a 'Page Cannot Be Displayed' error (tested in v6 and v8). When we perform the same query on the same machine, but bypass the Squid proxy, it works fine. The query takes about two and a half minutes to complete. There are a few timeout settings in Squid, but I honestly don't know what one to be looking at. Any possible solutions would be much appreciated. Cheers

    Read the article

  • Warning message in boot.ini

    - by MA1
    Hi everyone, I have a dual boot system with Windows XP Pro and Windows 7. Following are the contents of my system's boot.ini. ;Warning: Boot.ini is used on Windows XP and earlier operating systems. ;Warning: Use BCDEDIT.exe to modify Windows Vista boot options. ; [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /NOEXECUTE=OPTIN /FASTDETECT I just want to know about first two warning lines, whether these two lines are always present in dual boot system when the boot process is different for installed operating systems, for example xp + vista/w7 or windows2000 + vista/w7 etc? Regards,

    Read the article

  • Exchange 2010 periodically stops responding to SMTP events with error 421 4.4.1 Connection timed out

    - by Michael Shimmins
    After some help diagnosing why Exchange 2010 Enterprise stops responding to SMTP events. I can't find a pattern to it. It doesn't appear to be an actual timeout, as the server responds immediately with the error. To reproduce it I telnet into the server on port 25 and issue a EHLO. The server immediately replies with the 421: 421 4.4.1 Connection timed out Once this starts happening I've found restarting the exchange box is the only reliable way to get it flowing again. Sometimes restarting the Transport service or the mailbox attendant service seems to fix it, but this could be coincidental as it often has no effect.

    Read the article

  • Virtual NIC on VM couldn't ping externally after Vmotion

    - by ToreTrygg
    Today I vmotioned 5 MS SQL 2005 servers over to a new DRS Cluster. All SQL servers use the "Production_LAN" network and a single virtual NIC of type "VMXNET 3". The first 4 SQL VM (Windows 2003 Standard or Enterprise x32 bit) vmotioned over without a hitch. The last SQL VM I vmotioned (Windows 2003 Standard x64 bit R2) vmotioned over without error, but I upon completion, I could no longer ping the VM. I went into the VM and could not even ping the gateway, however I could ping the loopback. This SQL server is extremely busy in comparison with the previous 4 VM's. I restarted the server and it came back up with the virtual nic working just fine. The build of both servers (vmotioner and vmotionee) is ESX 4.0.0 175625 - So, pre-update 1. Should I suspect the network switch/VM for possibly not updating the mac table on the switch? Anybody else ever have this issue or know what may have caused it? Thank you!

    Read the article

  • Odd behavior on Shift-{Esc,Fx}

    - by ??????? ???????????
    Sometimes, when changing between the modes in Vim, I forget to take my finger off the Shift key. This innocent mistake is probably part of the luggage carried over from other terminals, but I have never seen my input treated this way. After changing from command mode to input mode, if I hit the Esc key while the Shift key is down, Vim will display <9b (Control Sequence Introducer) instead of switching to the command mode. At least two work-arounds to this intended behavior are available on the mintty site (faq, issue). " Avoiding escape timeout issues in vim :let &t_ti.="\e[?7727h" :let &t_te.="\e[?7727l" :noremap <EscO[ <Esc :noremap! <EscO[ <Esc " Remap escape :imap <special <CSI <ESC My question is about the syntax and the meaning of the first solution. From the looks of it, it seems like t_ti is being assigned a literal value, but I'm not sure why the "c address-of" operator is required. I'm also not sure why there are two noremap statements.

    Read the article

  • Can TP-Link router make phone calls?

    - by Umair Ashraf
    I have a TP-Link router with DSL service provided by a local company which serves it over the landline phone. My landline cord is plugged into an ethernet router which is then plugged into TP-Link wireless router. I can access internet with this wireless router all over my home with all computers. Landline Cord [into] Ethernet Router [into] TP-Link Wireless Router [air] Computers I would add that landline cord is also into a phone device which I use to make calls and that's not cordless. Now I am accessing internet via WiFi on my laptop and want to ask if is this possible to make landline calls via this same computer I am surfing internet through? What I am asking it to a dial-up via TP-Link router that goes through landline. You see the landline cord is the actual data gateway and is also used to make calls. So it can simultaneously send Data and Voice over the same wire.

    Read the article

  • Specific IP routing for VPN

    - by Roy
    Is there a way that I can prevent an entire subnet from using internal routing. The VPN server is supposed to be a way to access the company's intranet websites for some people, while for others it is supposed to do routing to the outside only and therefore not having access to any internal websites. The VPN server has a DNS on the actual server but not all should be using this DNS. Some of the users should be directly sent out of the server to the internet. Example: 10.0.0.1 is the DNS on the server, gateway for the VPN 10.0.0.2 is a user (A) on the VPN having access to the intranet websites (subnet is 10.0.0.0/25) 10.0.0.192 is a user (B) only needing routing and no access to intranet websites (subnet is 10.0.0.192/26) All traffic of user B should be directly rerouted out of the server. I have tried several iptables but without success.

    Read the article

  • Dismissing systray balloons with the keyboard?

    - by rangerchris
    This is probably a supplementary question to how to access the systray using the keyboard... I've read that, and done some googling (google fu lacking, or there really is no answer), but I can't find a nice quick keyboard shortcut to dismiss those info balloons that apps in the system tray choose to display every now and then. The hints for access in the linked question can't be used to close the balloon (and least when I've tried them here). Now I know I can wait for a timeout and they'll go away but if I can just hit , that'd be fanstastic. So... anyone aware of a keyboard shortcut?

    Read the article

  • How to clear stuck locked maildrop pop3 process

    - by Joshua
    I am using cyrus for imap and pop One of my users is getting the following error: Unable to lock maildrop : Mailbox is locked by POP server. I can see where it starts in the log. I've read that there is no physical lock file anymore (i've tried looking for it anyways) and that the solution is to just wait for the timeout, or kill the offending pop3 process. I know that this is happening because of a lossy connection on the part of the affected user, and that pop3 can only have 1 session active at a time. I need to manually clear the lock and I am having trouble finding the offending pop process. I have tried lsof, but it doesn't say how long the individual files (sockets) have been opened for. I've reduced the tcp keepalive time down to 5 mins, but I still need to reset this guy's lock. I could use some pointers. Thanks!

    Read the article

  • What are the advantages and disadvantages of having a hosted firewall?

    - by Roy
    Would you rather have your firewall hosted or in house if you've got the skills to manage it? We currently have 6 remote offices and 2 different ISP's, one private network and our firewall (Watchguard, licenses are due to expire) is also our main gateway. I don't see how a hosted firewall (in this case Fortinet) is going to work for us especially when it's cheaper to buy our own firewall and the transition from one ISP to a new provider will take some time because our current contracts aren't due to expire soon. What are to pros and cons of having a firewall hosted by your ISP in general?

    Read the article

  • Can't communicate with Primary DNS Server

    - by horsley
    A computer, with Windows 7, can't access any website by domain suddenly. Whether this computer use a wired link or connect to the WLAN, The fault persists IP and DNS obtained automatically, and seems normal (ipconfig /all return the correct info) I can visit websites by using HTTP proxy The DNS server is available, other computer in my room works properly. I can ping myself, the gateway and any other IP, but domains I can use nslookup and obtain the correct IP info There are some error information in the event log about dns client events explaining the client can not verify the DNS server available Windows network diagnosis explain that Windows can't communicate with the device or resource (Primary DNS Server) I guess the dns client should be blame. I tried to do the following things but the fault persist. Reinstall the driver of network adapter Reset TCP/IP (netsh int ip reset) Reset Winsock (netsh winsock reset) Reset LSP I don't want to reinstall the whole os, what should I do?

    Read the article

  • Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

    - by Lock
    I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

    Read the article

  • Memcached failover

    - by user25164
    We have 2 memcached servers configured and use the Eniym client. When one of the server is down, it appears this server is added to the deadServers list (ServerPool.cs) and tries to resurrect the server every 10seconds (we have configured deadTimeOut to be 10seconds). Attempting to connect to the failed server causes a TCP timeout, the pages take a long time to load which results in bad user experience. 1) What is the standard way of resolving this issue? There are some posts about removing the server from the deadServers list. Is it okay to do this? 2) What is the recommended deadTimeOut setting (I understand by default it's 2 mins and we've changed it to 10seconds in our implementation) 3) Am I correct in my understanding that the cached data is not replicated across Server 1 and Server 2? If Server 1 is down, then it goes to the database to fetch these values (and it doesn't really check Server2)? Any help is really appreciated.

    Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >