Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 114/315 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• How do you confirm network adapter is gigabit capable?

  - by StrandedPirate

  Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

  Read the article

• Best practice for assigning private IP ranges?

  - by Tauren

  Is it common practice to use certain private IP address ranges for certain purposes? I'm starting to look into setting up virtualization systems and storage servers. Each system has two NICs, one for public network access, and one for internal management and storage access. Is it common for businesses to use certain ranges for certain purposes? If so, what are these ranges and purposes? Or does everyone do it differently? I just don't want to do it completely differently from what is standard practice in order to simplify things for new hires, etc.

  Read the article

• How can I join two simple home networks together using an ethernet cable?

  - by Ilia Jerebtsov

  I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

  Read the article

• Macbook cannot see specific wireless network after being connected to it for a while

  - by donut

  Okay, so there's a single wireless network that my laptop has troubles with. My Macbook Pro used to be fine with it until it changed to using channel 13 (or 11?). Since then, after being connected to it for a while it disappears from my laptop's view. Other networks are showing up fine and other computers (including several Macs) have no troubles connecting to this network. If I clear my system cache using Onyx and then restart (sometimes a couple times) my laptop can see and connect to it again. But it seems that if I disconnect and try reconnecting I have to clear my cache again. One thing to note is that if I put my computer to sleep while connected to this network it has no problems reconnecting on wake up. I've got a 15" Macbook Pro 2,2 with Leopard 10.5.8.

  Read the article

• iPhone Cannot log into WiFi suddenly [closed]

  - by Stanley

  I suddenly get into this strange problem. My iPhone has been using the WiFi setup at my home for more than a year. Suddenly it cannot connect to the internet despite still having the full WiFi signal icon. Have an older iPhone 3 GS and it can still browse the net using the same WiFi. So the wireless router should be working. When I check the non-functioning iPhone, it has the "Router" and the "DNS" entries blank while the functioning iPhone has entries on both of the fields. Also the subnet Mask are different. Please help.

  Read the article

• Just LB or also Web Servers in Demilitarized Zone?

  - by Bradford

  In a load balanced environment, is it necessary to have all of the web servers in the DMZ? Or will just having the Load Balancer in the DMZ achieve the desired security? If it matters, the web server and application server are the same -- GF, Tomcat fronted by httpd on the same server, OAS, etc... LB - WEB/APPLICATION - DB Also, would the setup be different if it was LB - Web Server - Application Server - DB Thanks, Bradford

  Read the article

• SCM8014 to FVS338

  - by Jack

  I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

  Read the article

• Virtual machines interconnection inside Proxmox 2.1 Cluster

  - by Anton

  We have 3 physical servers (each with 1 NIC) in different datacentres, all of them are interconnected by openvpn bridged private network (10.x.x.x). Inside this network we have fully functional 3 nodes Proxmox 2.1 cluster. So, actually question is: Is there any "proper" way to make "global" local network (172.16.x.x) for all VMs inside cluster, so even if we move VM from one node to other we could reach it by static IP regardless of it's physical location? BTW, we can't add dedicated NIC to each server. Thanks in advance. EDIT: I have tried to make a separate openvpn bridge for 172.16.x.x, now I have at each server two interfaces: SRV1: openvpnbr1 - 172.16.13.1 vmbr0 - 172.16.1.1 SRV2: openvpnbr1 - 172.16.13.2 vmbr0 - 172.16.2.1 But now there is no connection between those ifaces: SRV1: ping 172.16.13.2 From 172.16.1.1 icmp_seq=2 Destination Host Unreachable SRV2: ping 172.16.13.1 From 172.16.2.1 icmp_seq=2 Destination Host Unreachable If I shut down vmbr0 interfaces, so there is connection between servers over openvpn, but vmbr0 is used by Proxmox... Where I am wrong?

  Read the article

• network layer reliability

  - by ghedas

  I have a question about the reliability of network layers, I think in the network layers there is a redundancy, my question is why both link-level and end-end reliability need?

  Read the article

• The RTL8111/8168B NIC under Linux and the r8168 driver

  - by nik

  So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Windows 7 backup network restore: "The network location cannot be reached, 0x800704CF"

  - by Znarkus

  When I try to restore from a backup image, I get this error. After I enter the network address (\\10.0.0.1\backup or \\z\backup), the wizard presents me with the network login dialog, which leads me to believe that it can connect to the network (yes, the share is password protected). I decided to install Windows 7, since I thought that I could restore the image from Windows. The restore process in Windows can locate the backups, but to do an image restore it needs to reboot to the wizard above. Which of course gives the very same error. This is what \\z\backup looks like. Please help, I'm getting desperate. Update: Forgot to mention that the NAS is running Ubuntu, if that's relevant.

  Read the article

• Is PLC speed affected by mixing different devices?

  - by CFP

  Hello everyone! At home, I have 4 PLC devices for my home network. Two of them are 85Mb/s powerlan PLC adapters, while the others are 10Mbps powerlan PLC adapters. I have not been able to determine reliably whether the presence of the 10Mb/s ones impact on the speed of the 85Mb/s ones. Is it possible that the bitrate is limited by the slowest devices on the network? Thanks!

  Read the article

• Is there a way to bridge two outgoing TCP connections in order to bypass firewalls and NAT?

  - by TK Kocheran

  We're all familiar with the problem of port-forwarding and NAT: if you want to expose something to accepting an incoming connection, you need to configure port-forwarding on the router or conjure up some other black magickery to "punch holes" in the firewall using UDP or something. I'm fairly new to the whole "hole-punching" concept so could someone explain how it works? Essentially, I'd like to understand how hole-punching would work and the theory behind it, as well as if two TCP connections could be bridged via a third party. Since there's no issue with outgoing TCP connections since it's handled with NAT, could a third party bridge the connections so that the two parties are still connected but without the bandwidth cost of traffic going through the third party?

  Read the article

• Creating basic, redundant gigE or IB storage network for Xen?

  - by StaringSkyward

  With only a modest budget, I want to move my 4 xen servers over to network storage -either NFS or iSCSI which will be determined based on how well it performs when we test it (we need good throughput and it must continue to work through link and switch failure tests). We may add another couple of xen servers at some point when this is done. I don't know much about the design and operation of storage networks, so would really appreciate some hints from those with experience. The budget is around $3,800 excluding the storage appliance. I am currently thinking these are my options to remain on budget: 1) Go for used infiniband hardware and aim for 10gb performance. 2) Stick with gig ethernet and buy some new switches (cisco or procurve) to create a storage-only ethernet LAN. Upgrade to 10gigE later but try to use hardware capable of it where possible to reduce upgrade costs. I have seen used, warrantied infiniband switches at reasonable prices (presumably because big companies are converging on 10gbit ethernet?) and the promise of cheap 10gb is attractive. I know nothing about IB, so here come the questions: Can I buy 2 x switches and have multiple HBAs in my xen and storage nodes to get redundancy and increased performance without complexity or expensive management software costs? If so, can you point me to some examples? Do NFS and iSCSI work just the same regardless? Is IB a sensible choice or could/should I use ethernet or FC on the same budget - I'm keen not to get boxed into a corner for future upgrades, however. For the storage I am likely to build a storage server using nexentastor with the intention that I can later add more disks, SSDs and add another server to provide a failover option at the storage level. An HP LeftHand starter SAN is also under consideration, too. Thanks in advance.

  Read the article

• Snow Leopard - resolving hostnames issue

  - by romant

  This worked in Leopard, although since Snowie came along … I have a Location setup with a DNS server to use [eg 10.0.0.17] , and a search string [eg sub.dom.ain.com] In the terminal: $ nslookup cake Server 10.0.0.17 Address: 10.0.0.17#53 Name: cake.sub.dom.ain.com Address: 10.0.0.38 So works like a charm. Although if I just the hostname cake in any other application within OSX - such as Safari/CoRD, they simply can't resolve the hostname. I have to instead use the FQDN cake.sub.dom.ain.com - why is this so? Why did this work in Leopard and is now broken? Would love a solution. Thanks

  Read the article

• Setting up Windows 2008 with VPN and NAT

  - by Benson

  I have a Windows 2008 box set up with VPN, and that works quite well. NPS is used to validate the VPN clients, who are able to access the private address of the server, once connected. I can't for the life of me get NAT working for the VPN clients, though. I've added NAT as a routing protocol, and set the one on in the VPN address pool as private, and the other as public - but it still won't NAT connections when I add a route through the VPN server's IP on the client side (route add SomeInternetIp IpOfPrivateInterfaceOnServer). I know I can reach the server's private interface (which happens to be 10.2.2.1) with remote desktop client, so I can't think of any issues with the VPN.

  Read the article

• Why DELL PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

  - by Kedare

  Hello ! I have a little question, I'm actually studing IT in France, and when looking on alternative on the very [...] very expensive Cisco equipments, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipments in France :( Thank you !

  Read the article

• How to configure router to give XBox top priority / most bandwidth?

  - by MrSparky

  Hi all - Newbie here so go easy... and apologies in advance if I blow the community etiquette / rules! Here's what I'm trying to do: I have a "D-Link DIR-655 Extreme N" wireless router and an XBox 360 w/ the old-style wireless connection thing (usb attachment)... I want to configure my router / network to give my XBox as much bandwidth as it wants, whenever it wants. I have tried giving the XBox a unique IP (within my network) and then tweaking the router to treat that IP as a top priority application (using the router's QOS stuff). Problem is whenever I turn off the xbox, I can't connect to the network the next time I start it up. It seems the only reliable setting in the XBox is to use "Automatic" for the IP settings within the Network Configuration area. Supposedly the D-Link ships with default settings that attempt to recognize a game console and give it top priority... but i've not seen good results (lots of stuttering / lag when someone else jumps online, etc). Any suggestions? thanks again!

  Read the article

• trying to connect to non-standard port over esxi guest network

  - by user52874

  I've got an exsi 5.5 box that has a redhat 6.5 guest and a win7 guest. The guest nics are connected on a vsphere standard switch. There is no connection from the vswitch to an outside physical nic. I can ping between the two boxes, each way. I can successfully psping redhat:22 from the win7 box. I can successfully tcping win7:139 from the redhat box. All firewalls are down on both boxes. I cannot connect from the win7 box to redhat:8003, either via psping redhat:8003, nor telnet redhat 8003, nor by the application client itself. sudo netstat -patn | grep 8003 on the redhat box shows that it's listening on 0.0.0.0. Any thoughts? suggestions?

  Read the article

• How do the routers communicate with each other ?

  - by Berkay

  Let's say that i want make a request a to a web page which is hosted in Europe (i live in USA).My packets only consist the IP address of the web page, first the domain name to ip address transformation is done, then my packets start their journey through to europe. i assume that MAC addresses never used in this situation? are they? First, my packets deal with many routers on way how these routers communicate with each other?, are router addresses added to my packet headers ? Second, is there a specific path router to router comminication or which conditions affect this route? Third to cross the Atlantic Ocean, are cables used or... ?

  Read the article

• Social network for internal company use

  - by khelll

  I'm seeking a social network app for employees in the company that can do the following: allows people to communicate within a company or across everyone on the social network (they can have access to a group or to everyone) post and archive interesting links, documents, etc. start a thread that goes to a group or to everyone lookup people’s info (profile) integrate w email so I can know if someone posts something new or responds to a questions Open source + customized deployment is a plus.

  Read the article

• public key infrastructure - distribute bad root certificates

  - by iamrohitbanga

  Suppose a hacker launches a new Linux distro with firefox provided with it. Now a browser contains the certificates of the root certification authorities of PKI. Because firefox is a free browser anyone can package it with fake root certificates. Can this be used to authenticate some websites. How? Many existing linux distros are mirrored by people. They can easily package software containing certificates that can lead to such attacks. Is the above possible? Has such an attack taken place before?

  Read the article

• how does ospf control flooding?

  - by iamrohitbanga

  what method is used by ospf protocol to prevent looping of flooded packets for link state advertisements? The packet header does not contain any timestamp. How do the routers recognize that it is the same advertisement that they sent before?

  Read the article

• Use one NIC to create multiple interfaces for Linux KVM

  - by Phanto

  I am working on a thesis research project, and I am having some difficulty figuring out how to make one NIC spawn several "bridge" interfaces such that each KVM VM can be seen on the local network. I am very new to KVM, and am still exploring what it can do. Below is the scenario that I am attempting to make (on a CentOS/RHEL 6 system): Linux KVM Host has 1 NIC (eth0) connected to a switch. Create multiple "bridge" or equivalent interfaces that are spawned off of eth0 that would provide a unique IP for each VM. This is so that each VM can communicate with other hosts on the network, and that other hosts on the network can communicate with the VM. IMPORTANT: I would like iptables on the KVM host to be able to manipulate/control/restrict the traffic that would be sent on those "bridge" interfaces. I would like to create a minimum of three VM's, each using their own unique "bridge" interfaces. I have previously made a br0 interface off of eth0, but unfortunately, I am unable to add any more to it. It appears that you can only bridge 1 interface to the NIC. I would like to bridge many to one. Would a tap device be able to do this? If so, how would it be set up? Effectively, I am attempting to replicate what can easily be created with VirtualBox on Windows, where each VM is given a "bridged" interface, and can live on the network. I want to achieve this very same thing with Linux KVM. Thank You EDIT: To be more descriptive, I want to achieve something that looks like this: This can be found on this page: http://en.gentoo-wiki.com/wiki/KVM#Networking_2 HOST +---------------+ | | KVM GUEST1 | | +--------------+ | +------+ | | | LAN ---+--- eth0 | +--+---+---- nic0 | KVM GUEST2 | | tap0----+ | |192.168.1.13 | +--------------+ | | tap1----+ | +--------------+ | | | +------+ | | | | | br0 +--+----------------------+---- nic0 | |192.168.1.12 | |192.168.1.14 | +---------------+ +--------------+

  Read the article

• what causes drops in apache throughput?

  - by Robbie Mckennie

  i was poking around in the windows task manager, and i found this cool network throughput graphing thing. so i wanted to see it max out, so i started downloading a 1.8gb image (from the localhost to a remote system). but, much to my surprise, it looked like this: i count 16 dips, so i divided the 1.8gb into 16 and i got 115mb. then i looked up the mtu of ip, and i knew the mtu of ethernet from my reading, both far smaller than 115mb. and since tcp is connection orientated, it doesn't have an mtu.

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >