Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 112/315 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119 | Next Page >

NFSv3 Asynchronous Write Depends on Block Size?

- by Joe Swanson

I am trying to figure out if my NFSv3 deployment is performing SAFE asynchronous writes. I suspect that it is doing strictly synchronous writes, as I am getting poor performance in general. I used Wireshark to look at the 'stable' flag in write calls, and look for 'commit' calls. I noticed that, with especially large block sizes, writes to appear to be performed asynchronously: dd if=/dev/zero of=/proj/re3/0/zero bs=2097152 count=512 However, smaller block sizes appear to be performed strictly synchronously: dd if=/dev/zero of=/proj/re3/0/zero bs=8192 count=655360 What gives? How does the client decide whether to tell the server to perform writes synchronously or asynchronously? Is there any way I can get smaller block sizes to be performed asynchronously?

Read the article
Multiple Internet connections, multiple networks and split access in Linux

- by Swapneel Patnekar

I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

Read the article
Is dual boot via wake on lan possible?

- by ianfuture

Is it possible to set up a PC so it can Wake on Lan and then have the option of which OS to boot into? I want to have a secondary PC with Windows and a *nix variant installed. I want the PC to be in a remote room so I can connect via a wireless hub to it and then boot it up as and when required and choose which OS to boot into. If it is possible how would I go about it? Any recommendations on how to do it or where I can get more info on how to do it? Thanks.. Ian

Read the article
internet connection drops randomly

- by Remus Rigo

hi all I have 3 PC's at home (with Win XP, Win 7 & Win 7) and a router. I am always connected to the internet through the router (PPoE connection). My problem is that sometimes when I want to search or open a page, my browser tells me that the server cannot be reached, as if I don't have a connection to the internet. Other times it logs me out from messenger, but browsing still works. FTP download/upload also works. If i disable and enable the LAN then all works fine. The connection doesn't always drop on all three PC's at the same time. Anyone got any idea besides re-installing OS? thanks

Read the article
please demystify the 10Gb ethernet interfaces, cables

- by maruti

this really is a Dell question but tempted to ask the experts @ serverfault. choosen a Dell powerconnect 8024 10GbE switch. per the spec sheet this has 10GbaseT ports. "24x 10GBASE-T (10Gb/1Gb/100Mb) with 4x Combo Ports of SFP+ (10Gb/1Gb) or 10GBASE-T" the HBA on my storage server has 10G CX4 copper ports Dell does not sell any cables and this adds to my confusion. from the picture Dell 8024 seems to have RJ-45 type ports on the front panel? my question: is it a RJ-45 + CX4 cable or CX4 + CX4 cable?

Read the article
Can't access an internal IIS web site via IP address, only hostname

- by chris-untrod-com

I have a machine on my home network running Windows Server 2008 (IIS7) with a web application running under default website called HTCOMNET. The network is just on a Windows Workgroup. The server is named nas1 and has a (dynamically assigned) IPv4 address of 192.168.2.12. I can ping 192.168.2.12. When I ping the machine by name ("nas1"), the hostname resolves to an IPv6 link-local address (as opposed to the ipv4 address). In a browser, I can go to http://nas1/HTCOMNET/ and IIS serves the site, no problem. But if I go to http://192.168.2.12/HTCOMNET, no dice. I have all the windows firewalls turned off. Any idea what's going on? I can't for the life of me figure out why I can't hit IIS via the IP. I feel like it's something really obvious, but i can't figure out what. Thanks!

Read the article
VoIP - need setup ip network with our SIP operator

- by evgeniy.labusnkiy

Need to make next one: for ex i'm now in UAE, but i need to make a call to my girlfriend who is in Ukraine. I need to find the way how can i make the connection to my home router and make the call from VoIP gateway using my standard phone network in Ukraine. I have some imagination about this, to do like this: Connect to router or VoIP gateway (how? soft?) using inet - Gateway make a call using standard phone line in my country. Any ideas? Best practice? What devices i need to make this? Pay attention that i don't want to use any SIP providers. Thats a lot!

Read the article
How do I mount my Linksys WRT610N to maximize range and connection strength?

- by KnipSter

The current generation linksys routers have internal antennae. I currently house my primary router in my basement and would like to maximize the strength with which it covers my home. Is there directionality to the antennae, should I mount it vertically on a wall?

Read the article
Unable to connect to MSN network with Adium

- by Adam Driscoll

I'm new to the Mac world and tried both MSN Messenger for Mac (7.0 and 8.0 beta) as well as Adium to connect to the Windows network. I've enable 'Allow all incoming connections' in the Firewall settings. Windows Live Messenger works fine when connecting through the same router on my Windows laptop. I've triple checked my password and verified it through a web browser and Windows Live. Any ideas what my issue could be?

Read the article
Route traffic from one VPN to a second VPN

- by Dominic

I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

Read the article
QoS, Squid, Virgin superhub

- by swiss196

I'm a student and have just moved into a house of 6. We've setup 100mb broadband with Virgin and get quite good speeds on it so we're really pleased. However, as there are 6 of us, who all like to stream/game/download etc I was looking at setting up QoS to ensure speeds were fair/equal etc. I looked into it and found out that the Virgin Superhub can't do it out of the box, so my next option is to setup squid proxy on my machine (always on) to act as at transparent proxy and provide QoS etc. However, I'm not really sure how to do this and had a look on the Internet but couldn't see any guides as such! I was wondering if someone could give me some more and perhaps provider a summary of the steps involved - and let me know if this is possible with the SuperHub etc. Thanks, Dave

Read the article
How to use the AWUS036H on MacBook Pro with Lion and Backtrack in VM?

- by Swader

I have the AWUS036H USB WiFi adapter and have recently upgraded the OSX to Lion. The thing is, there are no drivers for Lion for the AWUS036H, and I would have to boot into 32bit mode every time I want to launch the adapter as per instructions here: http://www.youtube.com/watch?v=n9_HAGi1ce0 I also want to install BackTrack as I deal in networks a lot for my company. While this would be a simple matter on any other laptop, the company issued Macbook does not allow booting into any OS other than MacOSX or Windows with Bootcamp. Now, since dual booting into BT is not an option, I would like Backtrack to run in VM inside my MacOSX Lion - and this it does. It works like a charm inside VirtualBox. But since there are no 64bit drivers for the wifi adapter, Lion doesn't recognize it and cannot install it. This, in turn, means that Backtrack cannot see it even though AWUS036H usually works flawlessly with BT. How can I make my VM-based BT see the wifi adapter even if the parent OS doesn't see it, if at all? Is there a way, or am I better off buying a new WiFi adapter that supports OSX 10.7 such as the AWUS036NHR?

Read the article
FortiGate firewall configuration with /30 and /28 networks

- by slyderc

I have fiber coming in from a new ISP which is being handed off via Ethernet on a single physical port. I'm having doubts about how to approach the configuration on my FortiGate 200A firewall because I've been given a /30 containing the ISP's gateway and another /28 for external IPs I can use: x.y.76.12/30 (.13 is the GW) x.y.76.64/28 (public IP space) How do I configure the FG200A's WAN1 interface to be aware of the two networks? As I only have one physical ISP port, will I need to plug it into a switch to break-out two cables and use a DMZ port on the FG200A for setting up the /28? Thanks in advance for your insight!

Read the article
Setting up 802.1X wireless connection on OSX

- by hizki

I am an OSX user, I have Snow Leopard 10.6.5 and an updated AirPort. I am trying to connect to my university's wireless network, but it has a complex security that I am having trouble defining... Here there are instructions for connecting with Windows XP, Windows 7 and Linux. Can someone please instruct me what should I do to set up this network on my MAC? Thank you. P.S. I have had previous success in setting up this network, but I have no idea what I did that made it work. Since I updated my AirPort it worked only seldomly and very slowly... Before the update, even when it worked it never remembered my password.

Read the article
Problem with Jumbo Frames

- by Spookyone

Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: * D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU * Synology DS107+, Firmware 3.0-1337 * Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

Read the article
Need assistance setting up Linux Router with 2 public lans

- by user195407

I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

Read the article
Download - Upload is too slow on Centos

- by Mehdi

My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

Read the article
Oracle 11g network configuration

- by Kylo

I installed Oracle 11g Enterprise Edition on my Windows 7 Pro. My problem is that I cannot log into database from other host (local network). When I connect to database using Oracle SQLdeveloper everything is ok as long as I specify 'localhost' in connection configuration. However, when I change it to '192.168.0.190' which is my host IP address I get 'The Network Adapter could not establish the connection'. I get the same error when logging in from other host in local network. What is the problem?

Read the article
All nework interfaces hang for seconds while one interface goes up/down

- by user3698377

I am building a client/server application that uses several network interfaces in parallel for redundancy, and I have noticed that while one network interface goes down or goes up, the communication on other interfaces hangs for several seconds. I could reproduce this behavior without my application in a simple way: there are 2 interfaces available on computer 1 ( Ethernet and WiFi ) ping from computer 2 the IP address of the Ethernet connection of computer 1 disconnect the WiFi of computer 1 ping hangs for seconds, and then the packets are traveling again between the 2 computers. The hanging happens as well if I turn back on the WiFi connection on computer 1. It happens as well if I ping the WiFi IP, and turn off/on the Ethernet connection ( or unplug/plug the cable). I am using Linux Ubuntu 12.04 on both computers. Any ideas why is this happening, and if / how can it be avoided?

Read the article
Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

- by Nate

I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

Read the article
Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

- by Nate

I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

Read the article
ISP Load Balancing with ISA 2006

- by Bill Best

I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

Read the article
Connection drops while transferring large files to one server on a network

- by Charlotte

My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

Read the article
Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

- by techaddict

Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

Read the article
DNS server at router level vs. computer level

- by Craig

I've three questions. Is it better/faster/optimal to set up your server's preferred and alternate DNS servers in your OS's network settings or in your router settings? Will it cause problems if it is set up in both places, both pointing to the same IPs? I am running Windows and I have my network assign a static IP to one of my computers. This doesn't allow me to obtain the DNS server addresses from my router automatically. Is there an IP I can put in that will cause it to take the DNS server addresses from the router?

Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119 | Next Page >