Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 118/278 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Multiple External IP Ranges on a Juniper SSG5

  - by Sam

  I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

  Read the article

• windows installer service could not be started

  - by Fischer

  I'm on windows 7 64 bit, i'm using the admin accouunt, i try to install some programs, but can't, i troubleshooted the error that i got, and turned out that windows installer service is stopped, i tried to start it, it says windows installer service could not be started because its disabled or it has no enabled devices associated with it. Error 1058 How to fix it? Note that the laptop has an expired bitdefender installed on it. I don't know if it's causing the problem or not, i just thought it was worth mentioning since i had many problems with misconfigured or expired antiviruses before. The MSIServer could not be started as well, and i tried to run as administrator The laptop is not mine, i'm just trying to fix it

  Read the article

• Skipping scheduled self-tests and predicting drive EOL

  - by Steve Madsen

  For a few weeks now, smartd has been reporting that it is skipping some of its scheduled self-tests on the weekends: Apr 24 18:29:32 calvin smartd[4758]: Device: /dev/sda, skip scheduled Offline Immediate Test; 40% remaining of current Self-Test. Apr 24 18:29:33 calvin smartd[4758]: Device: /dev/sdb, skip scheduled Offline Immediate Test; 50% remaining of current Self-Test. The drives in this RAID-1 array are set to run an offline test four times a day, a short self-test at 2am every day, and a long self-test on Saturdays at 2am. For some reason, it looks like the long self-test is taking longer, causing the other scheduled tests to be skipped. First question: is this a sign of likely drive failure? Then today, smartd reported that a self-test failed. Here is the output of smartctl -a /dev/sdb: smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 family Device Model: ST3250823AS Serial Number: 3ND1GNBC Firmware Version: 3.03 User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Apr 25 13:15:34 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 047 039 006 Pre-fail Always - 168450357 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 33 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 9 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 654745480 9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 40141 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 51 194 Temperature_Celsius 0x0022 037 062 000 Old_age Always - 37 (0 17 0 0) 195 Hardware_ECC_Recovered 0x001a 047 039 000 Old_age Always - 168450357 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 40131 - # 2 Extended offline Completed: read failure 30% 40129 379795511 # 3 Short offline Completed without error 00% 40084 - # 4 Short offline Completed without error 00% 40060 - # 5 Short offline Completed without error 00% 40036 - # 6 Short offline Completed without error 00% 40013 - # 7 Short offline Completed without error 00% 39990 - # 8 Extended offline Completed without error 00% 39977 - # 9 Short offline Completed without error 00% 39919 - #10 Short offline Completed without error 00% 39895 - #11 Short offline Completed without error 00% 39872 - #12 Short offline Completed without error 00% 39848 - #13 Short offline Completed without error 00% 39824 - #14 Short offline Completed without error 00% 39801 - #15 Extended offline Completed without error 00% 39789 - #16 Short offline Completed without error 00% 39754 - #17 Short offline Completed without error 00% 39732 - #18 Short offline Completed without error 00% 39707 - #19 Short offline Completed without error 00% 39683 - #20 Short offline Completed without error 00% 39660 - #21 Short offline Completed without error 00% 39636 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Given that this drive is about 4.5 years old, I am probably tempting fate by keeping it in service. SMART doesn't seem to get much respect as a reliable way to predict drive failure. What else can I use to get an early indication of drive failure?

  Read the article

• Can't connect to Apple Time Capsule in home network using Home Plugs from Win 7 Machine

  - by Eugene

  I have the following home network setup with subnet 255.255.255.0 but recently moved my time capsule to a different location when I added a third Home Plug and can no longer ping or map a network drive to it from the Windows 7 Machine. However using Airport Utility on the Windows 7 machine I can manually configure the Time Capsule. Using a Macbook on WIFI Network 1 or 2 - I can backup to the time capsule, so its accessible via both the router wifi network and the time capsule wifi network. The Time Capsule is set to BRIDGE function - ie no NAT or DHCP server enabled. Any bright sparks out there that can help diagnose the problem? Router (192.168.1.254) WIFI Network 1 | | |---- Home Plug one |---- Home Plug Two | |---- Computer A Windows 7 (192.168.1.160) | |---- Printer (192.168.1.69) |---- Home Plug Three | |---- Apple Time Capsule (192.168.1.150) WIFI Network 2 |---- Smart TV (192.168.1.70) | |---- Apple TV (192.168.1.4)

  Read the article

• Enable hardware virtualization in BIOS?

  - by rhon

  I am running a FOXCONN AM2+ M61PMV with an AMD Athlon II X2 240 Windows 7 ultimate 64 bit. From startup I have hit the del key and the options for enabling the hardware virtualization are not there. I have checked the Microsoft tool that says I can run virtual and i have checked SecurAble, that says yes. But I have an open case w/microsoft (they've been trying for a week [7 tech support people later]) and they're saying that I need to ensure that the hardware is enabled. Where do I go to see? Is there another way besides from the startup?

  Read the article

• Centos 6.3 install reiserFS support

  - by Alon_A

  I'm trying to change an existing ext4 partition to reiserFS in Centos 6.3 64bit. I've updated the kernel to Centos Plus: First, I've updated /etc/yum.repos.d/CentOS-Base.repo: In the [centosplus] section: enabled=1 includepkgs=kernel* Then I ran yum ypdate and my Kernel was updated to Centos Plus: [root@vappsil disk]# uname -r 2.6.32-279.11.1.el6.centos.plus.x86_64 Then, I've added this to /etc/yum.repos.d/CentOS-Base.repo into the [centosplus] section: includepkgs=kernel* jfsutils reiserfs-utils into the [base] and [updates] section: includepkgs=kernel* jfsutils reiserfs-utils But when trying to execute: yum install reiserfs-utils I get: No package reiserfs-utils available. How can I install the reiserFS-utils package to create a reiserFS partition?

  Read the article

• bind9 dns proxy

  - by Zulakis

  We are offering multiple SSL-enabled services in our local network. To avoid certificate-warnings we bought certificates for server.ourdomain.tld and firewall.ourdomain.tld. We now created a zone in our local DNS-server in which we pointed the hosts to the corresponding private-ips. Now, each time another record for ourdomain.tld, like for example www.ourdomain.tld or alike are changed, we need to update it on both our public-dns-server AND the local dns-server. I would like our local bind-dns to serve all the information from our public-dns but serve different information for these 2 hosts. I know I could possibly have our private-ips in our public-dns but I don't want that for security reasons. The internet dns-server is being managed by a third party, while we have full control of the intranet one. Because of this I am looking for a solution which lets the intranet retrieve the records from the internet one.

  Read the article

• iChat can't authenticate to Lion Server 10.7.2 [migrated]

  - by glenstorey

  I've enabled iChat and iCal Server through our local 10.7.2 Server which has DNS set up correctly. I can add the server account via a client's System Preferences (under other - Mac OS X server) and it authenticates with my shortname correctly. However, when I load iChat, I get this error message: Where the account is [email protected]. The password and username is correct. Console throws this error: 22/11/11 3:03:31.135 PM imagent: [Warning] XMPPConnection: Error: Error Domain=XMPPErrorDomain Code=105 "The operation couldn?t be completed. (XMPPErrorDomain error 105.)" UserInfo=0x7f81bbe2a3e0 {XMPPErrorText=service requested for unknown domain} DNS is set up correctly (it's working for Profile Management, Software Update Server and Web Services) but I can't get iChat to work correctly. How can I get clients to authenticate? FYI: It's probably worth noting that I get the exact same error messages when I use [email protected] instead of [email protected]. Also posted this question on Apple Discussion here.

  Read the article

• IIS7 FTP Setup - An error occured during the authentication process. 530 End Login failed

  - by robmzd

  I'm having a problem very similar to IIS 7.5 FTP IIS Manager Users Login Fail (530) on Windows Server 2008 R2 Standard. I have created an FTP site and IIS Manager user but am having trouble logging in. I could really do with getting this working with the IIS Manager user rather than by creating a new system user since I'm fairly restricted with those accounts. Here is the output when connecting locally through command prompt: C:\Windows\system32>ftp localhost Connected to MYSERVER. 220 Microsoft FTP Service User (MYSERVER:(none)): MyFtpLogin 331 Password required for MyFtpLogin. Password: *** 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: An error occured during the authentication process. 530 End Login failed. I have followed the guide to configure ftp with iis manager authentication in iis 7 and Adding FTP Publishing to a Web Site in IIS 7 Things I have done and checked: The FTP Service is installed (along with FTP Extensibility). Local Service and Network Service have been given access to the site folder Permission has been given to the config files Granted read/write permissions to the FTP Root folder The Management Service is installed and running Enable remote connections is ticked with 'Windows credentials or IIS manager credentials' selected The IIS Manager User has been added to the server (root connection in the IIS connections branch) The new FTP site has been added IIS Manager Authentication has been added to the FTP authentication providers The IIS Manager user has been added to the IIS Manager Permissions list for the site Added Read/Write permissions for the user in the FTP Authorization Rules Here's a section of the applicationHost config file associated with the FTP site <site name="MySite" id="8"> <application path="/" applicationPool="MyAppPool"> <virtualDirectory path="/" physicalPath="D:\Websites\MySite" /> </application> <bindings> <binding protocol="http" bindingInformation="*:80:www.mydomain.co.uk" /> <binding protocol="ftp" bindingInformation="*:21:www.mydomain.co.uk" /> </bindings> <ftpServer> <security> <ssl controlChannelPolicy="SslAllow" dataChannelPolicy="SslAllow" /> <authentication> <basicAuthentication enabled="true" /> <customAuthentication> <providers> <add name="IisManagerAuth" enabled="true" /> </providers> </customAuthentication> </authentication> </security> </ftpServer> </site> ... <location path="MySite"> <system.ftpServer> <security> <authorization> <add accessType="Allow" users="MyFtpLogin" permissions="Read, Write" /> </authorization> </security> </system.ftpServer> </location> If I connect to the Site (not FTP) from my local IIS Manager using the same IIS Manager account details then it connects fine, I can browse files and change settings as I would locally (though I don't seem to have an option to upload files). Trying to connect via FTP though either through the browser or FileZilla etc... gives me: Status: Resolving address of www.mydomain.co.uk Status: Connecting to 123.456.12.123:21... Status: Connection established, waiting for welcome message... Response: 220 Microsoft FTP Service Command: USER MyFtpLogin Response: 331 Password required for MyFtpLogin. Command: PASS ********* Response: 530 User cannot log in. Error: Critical error Error: Could not connect to server I have tried collecting etw traces for ftp sessions, in the logs I get a FailBasicLogon followed by a FailCustomLogon, but no other info: FailBasicLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E StartCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | LogonProvider=IisManagerAuth StartCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | provider=IisManagerAuth EndCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} EndCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} FailCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E FailFtpCommand SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ReturnValue=0x8007052E | SubStatus=ERROR_DURING_AUTHENTICATION In the normal FTP logs I just get: 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelOpened - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 USER MyFtpLogin 331 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 PASS *** 530 1326 41 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelClosed - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - If anyone has any ideas than I would be very grateful to hear them. Many thanks.

  Read the article

• Windows could not set up internet connection sharing (ICS)

  - by Osa

  I'm trying to make an ad-hoc network for personal uses.. while creating it, it was created but when i tried to turn internet sharing on i got this error Windows could not set up internet connection sharing (ICS) I looked up google what is ICS and i found that it was an option in sharing tab in my connection properties, so i tried to enable it and i got this error An error occurred while internet connection sharing was being enabled. The dependency service does not exist or has been marked for deletion. I tried to also look up google for solution for this and i ended up with nothing really, i tried to enable the required services @ services.msc for it.. rebooted and still same thing it was working a while ago (had a problem at enabling my wireless for about 2 months and i just found a solution for it..) for some reason it doesn't now

  Read the article

• Why Mac cannot connect to Iphone?

  - by martin08

  I couldn't always ssh to my iPhone from my Mac. They're both on the same wifi network but sometimes the connection is established, sometimes it failed. From my Mac: $ ssh [email protected] ssh: connect to host 192.168.0.102 port 22: Operation timed out $ ping 192.168.0.102 PING 192.168.0.102 (192.168.0.102): 56 data bytes ping: sendto: No route to host ping: sendto: Host is down ping: sendto: Host is down I enabled SSH on the phone and am sure it can load webpages. So what might be a reason why they cannot connect? Thanks

  Read the article

• autofs mac os x afp not loading as correct user?

  - by Stephen Furlani

  Hello, I am way out of my depth, and I am trying to get all of my nodes on a cluster to mount a drive on my head node. I've got /etc/auto_master and /etc/auto_afp configured according to Apple's "Autofs: Automatically Mounting Network File Shares in Mac OS X" White Paper: /etc/auto_master +auto_master # Use directory service /net -hosts -nobrowse,hidefromfinder,nosuid /home auto_home -nobrowse,hidefromfinder /Network/Servers -fstab /- -static /- auto_afp /etc/auto_afp /Volumes/userA -fstype=afp afp://userA:[email protected]:/ /Volumes/userB -fstype=afp afp://userB:[email protected]:/ I am logged into a compute-node as userA. automount appears to mount both /Volumes/userA and /Volumes/userB to head-node.local:/Users/userA/Documents/ even though I have usernames, passwords, and user-directory specified in the afp url. If I go and login with Finder - it mounts userB appropriately. File sharing and cd/dvd sharing is enabled on all computers involved. Am I doing the right thing, and if so, what did I do wrong? -Stephen

  Read the article

• How do I make vim's autoindent not drop trailing spaces?

  - by Joey Adams

  In some text editors (e.g. Kate, gedit), when auto indent is enabled, pressing return twice will leave a trailing whitespace (which I want): if (code) { .... ....| } While others cater to the coding standard where trailing spaces (even in blank lines) aren't allowed: if (code) { ....| } What annoys me about this is that if I arrow up after auto-indenting, the auto-indent is lost: if (code) { | .... } If I run vim and :set autoindent , I get the latter behavior. My question is, how do I set vim to keep the trailing spaces rather than automatically removing them if they go unused?

  Read the article

• Ngingx won't start with fastcgi_split_path_info" error

  - by Ke

  I heard that nginx is faster and since I'm on a VPS with low RAM I thought I would try it out. I got through this tutorial http://www.howtoforge.com/installing-php-5.3-nginx-and-php-fpm-on-ubuntu-debian But I now get the following error: unknown directive "fastcgi_split_path_info" in /etc/nginx/sites-enabled/default:28 What might be causing the problem? I can't find any reference to the problem on Google. Also I have heard conflicting things about nginx vs Apache. Some say use one, some say the other. I'm using all sorts of things such as rewrite rules, proxies etc. Am I setting myself up for a fall by using nginx? If I go for Apache: how can I tweak it so that it performs better on a low RAM VPS?

  Read the article

• Implications of allowing Windows clients to use NTLMv1?

  - by Boden

  I have a web application that I'd like to authenticate to using pass-through NTLM for SSO. There is a problem, however, in that NTLMv2 apparently will not work in this scenario (without the application storing an identical password hash). I enabled NTLMv1 on one client machine (Vista) using its local group policy: Computer-Windows Settings-Security Settings-Network Security: LAN Manager authentication level. I changed it to Send LM & NTLM - use NTLMv2 session security if negotiated. This worked, and I'm able to login to the web application using NTLM. Now this application would be used by all of my client machines... so I'm wondering what the security risks are if I was push this policy out to all of them (not to the domain controller itself though)?

  Read the article

• Centos and dell PowerEdge Rxxx Series.

  - by OrenM

  hi we lately purchase few dell servers all of them from Rxxx series couple of R410 and R710 the OS we used on those servers is: CentOS 5.4 we're getting very weird error messages and we lost network connectivity couple of times (restarting the network interface was needed to fix it) the messages we're getting are: Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Uhhuh. NMI received for unknown reason 20. Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Do you have a strange power saving mode enabled? Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Dazed and confused, but trying to continue we have never seen those messages in the previous series of dell poweredge servers do someone here using centOS 5.4 on Rxxx series? did it happen to him too? maybe you have a suggestion about how to prevent it from happening

  Read the article

• website not accessible with IIS6 while NAT is configured in Windows 2003

  - by Mohammed Rizwan

  I have Windows2003 server configured with IIS 6. Until now it was working fine, but since I enabled NAT for my users to access the internet via this server, the website becomes unavailable. Note that I have two nics on the server one is WAN and 2nd is for LAN. Both IPs are behind the firewall. If I stop the NAT then the website is available externally. I tried to search the answer in this forum but didn't find appropriate one or maybe didn't properly understand. I'll appreciate if anyone can help me sorting out this issue.

  Read the article

• Why do I see router and not my real IIS?

  - by Tim Tom

  I am trying to access IIS through web but unable to do so. Basically I have a router (which functions as router and modem) that is given by ISP and I have another router connected to the router given by ISP. My ISP's router can be visited through 192.168.0.1 and the router that I connected to ISP's router can be visited through 192.168.1.1 Please see my ISP's router: As you can see I have DMZ enabled for my router of 192.168.1.1 Now please see my router of 192.168.1.1: As you can see I added a virtual server for port 80 where 192.168.1.125 is my private IP. I rebooted both of my modems an tried to visit my IP from: http://www.whatsmyip.org/ and after doing so, when I type my live IP I still see my router of 192.168.0.1 instead of my IIS. What am I missing? Note: I have disabled Firewall on both of the routers. Any help would be appreciated.

  Read the article

• Why do I see router and not my real IIS?

  - by Tim Tom

  I am trying to access IIS through web but unable to do so. Basically I have a router (which functions as router and modem) that is given by ISP and I have another router connected to the router given by ISP. My ISP's router can be visited through 192.168.0.1 and the router that I connected to ISP's router can be visited through 192.168.1.1 Please see my ISP's router: As you can see I have DMZ enabled for my router of 192.168.1.1 Now please see my router of 192.168.1.1: As you can see I added a virtual server for port 80 where 192.168.1.125 is my private IP. I rebooted both of my modems an tried to visit my IP from: http://www.whatsmyip.org/ and after doing so, when I type my live IP I still see my router of 192.168.0.1 instead of my IIS. What am I missing? Note: I have disabled Firewall on both of the routers. Any help would be appreciated.

  Read the article

• Multiple CAS servers with Microsoft Exchange and selective authorization

  - by John Wilcox

  I have a Microsoft Exchange 2010 organization within one Microsoft Windows domain and I have users accessing it through OWA. For simplicity lets say I currently have one CAS server (CAS 1) which is accessible only through a VPN connection. Lets call the users connecting to the first CAS group a. For some users though, I need to install another CAS server (CAS 2) so that they can connect without using a VPN connection. Lets call those users group b. What I need to achieve is that group a can only log in to CAS 1 and group b can only log in to CAS 2. Now I know that one can disable/enable OWA per user but in my case that is not enough because OWA must be enabled for both groups.

  Read the article

• SonicWall and Windows CA

  - by Nathan C

  I'm attempting to import a certificate created by a CA I've set up in Windows using AD CS. I've done the following: 1) Created my own CA (MyCompany) 2) Enabled web services (mostly for ease of configuration) 3) Generated a certificate request on the Sonicwall itself 4) Used web services to sign the certificate 5) Imported the sign certificate into the Sonicwall ...this caused the certificate to show "No" for the Verified field. 6) Imported the CA's certificate. This is where I get stuck. I attempted to import the CRL list, but get the following error: CRL Error - Verification failed using CA certificate. No further errors appear in the logs. Without the CRL list the certificate won't verify and it doesn't appear under the "Administration" page so I can select it for use via HTTPS. Any ideas?

  Read the article

• Is Hyper-V Server 2008 working on Intel's Atom platform

  - by Josip Medved

  Did anybody try to install Hyper-V on Intel Atom platform? Hyper-V requires: x64 compatible processor with Intel VT or AMD-V technology enabled Hardware Data Execution Prevention (DEP) It seems that both requirements are satisfied with Atom as processor. However, I wonder whether there is some blocking issue (e.g. BIOS that does not support it) since all Atom motherboards I checked had quite old north/south-bridge. My intentions are to run two low-requirements virtual machines (embedded Linux), so performance should not be an issue.

  Read the article

• How to configure Apache (sites-available vs httpd.conf)

  - by Edan Maor

  Hi, I'm brand new to Apache so this might be a stupid question. I've been trying to follow a few basic tutorials explaining how to get Apache up and running (on ubuntu, running on Amazon). I've mostly come up blank, because all the tutorials told me to configure httpd.conf (to add DocumentRoot, etc.). I've now stumbled across one tutorial that told me to add site configurations to the sites-available directory (under /etc/apache), and then symlink to it from sites-enabled. Configuring this way seems to work. But now I'm confused - how am I supposed to configure Apache? Most tutorials still seem to say that I should be using httpd.conf. Which one should I be using? What's the difference? Why are all the tutorials "wrong" (if they are)? Thanks!

  Read the article

• What does the email header "X-CAA-SPAM" refer to?

  - by lotri

  I've got an application that sends out notification emails to users of the application (this is not spam; the information in these emails is solicited and useful, and is also a feature turned off by default and must be enabled by the user). The app is still in beta, and one of our testers reports that the notification emails are going to his junk mail folder in Outlook 2003. This is the only reported case of this, but I asked him to send me the email headers from the message, and I noticed that there is a header there labeled "X-CAA-SPAM" with a value of 00000 . I'm a programmer, so I'm fairly green in the world of successful automated emails - does anyone know if this header is the culprit? If not, any suggestions?

  Read the article

• .htaccess has no effect

  - by Primož Kralj

  I am loosing hours with this (should-be) simple task. I want to restrict access to my website, which is on my server in /var/www/. I've created /etc/apache2/passwords file with httpasswd successfuly (user primoz). I've put .htaccess in /var/www/ and this is the content: AuthType Basic AuthName "RestrictedFiles" AuthBasicProvider file AuthUserFile /etc/apache2/passwords Require user primoz My website is still accessible. I also tried editing the /etc/apache2/sites-enabled/000-default - line AllowOverride None to AllowOverride All. No need to mention that it didn't make any changes. Should restricting really be this frustrating? EDIT: /etc/apache2/httpd.conf is empty by default because I run server on Debian - which uses apache2.conf instead. Here is the whole apache2.conf.

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >