Search Results

Search found 17130 results on 686 pages for 'computer lab'.

Page 119/686 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

• New to building computers worried about temps

  - by dave

  I'm new to building my own computers and I was wondering about maximum temperatures. I understand that the room temp can affect the computers temp but how relevent is it? I understand that if my room temp is 20°C none of my computer parts could be lower than that. But if my room is 27°C instead of 20°C would this cause my computers parts to heat up more/faster? My new computer I built myself for gaming is i7 2600k 16gb ram ddr3 1600 hd6970 2 gb 240gb ssd ( bought a nas with 3 2tb drives in raid 5 for my home network ) 850w modular psu I also have my old hp computer i3 2120 8gb ram hd6770 1tb hdd I also have 3 laptops in my household, but I am not worried about their temps, they heat up my legs but they are never under stress. Due to size and money reasons I used an old case and it only has one of the sides left on it. Is this bad for the computer and will the extra dust cause problems? Or should I leave it this way or take the missus wrath and buy a case? If so is there any certain case I should get? I don't care about looks I just want card reader and usb slots and for it to run as cool or cooler than now, my case has 1 fan. Also what are the max temps for my new and old computer parts? Is 40°C under load ok for my CPU, what about 70°C for my GPU is that ok too, or should I worry? What are normal and safe temps for my components? I have looked around but there seem to be lots of different answers. I know that 100°C is bad but I want my parts to last as long as possible and this site always seems to give good replies without arguing or flaming.

  Read the article

• VLAN setup on my PC

  - by Surjya Narayana Padhi

  Hi Geeks, I am bit new to VLAN. I want my two computers communicate through VLAN. I have following queries. As I am new to it my queries may be somewhat vague in some points. But i would like to hear from experts for my basic queries. I have two PCs Computer A and Computer B in two different IP networks Network A and Network B Both my PC has windows OS installed. How to send a VLAN(#Number) tagged packet from Computer A to Computer B and how to detect and untag the packet at Computer B? (Please provide the steps for windows OS) For this action do I need to check if my ethernet card supports VLAN tagging/untagging? If yes how can I know if my card supports it or not? Is the VLAN applied for Wireless ethernet controllers also? Do I need any switch or router for this action? Experts please given your inputs so that I can have a strong basic. If anyone can give some inputs how i can detect those VLAN in wireshirk, it will be helpful me also. Thanks in advance.

  Read the article

• How can I find out if a port is opened or not?

  - by Roman

  I have installed Apache server on my Windows 7 computer. I was able to display the default index.php by typing http://localhost/ in the address line of my browser. However, I am still unable to see this page by typing IP address of my computer (neither locally (from the same computer) no globally (from another computer connected to the Internet)). I was told that I need to open port 80. I did it (in a way described here) but it did not solve the problem. First of all I would like to check which ports are opened and which are not. For example I am not sure that my port 80 was closed before I tried to open. I am also not sure that it is opened after I tried to open it. I tried to run a very simple web server written in Python. For that I used port 81 and it worked! And I did not try to open the port 81. So, it was opened by default. So, if 81 is opened by default, why 80 is not? Or it is? ADDITIONAL INFORMATION: 1. In my httpd.conf file I have "Listen 80". 2. This site tells me that port 80 on my computer is opened. 3. I get different responses if I try http://myip:80 and http://myip:81. In the last case browser (Chrome) writes me that link is broken. In the first case I get: Forbidden You don't have permission to access / on this server. 4. IE writes that "The website declined to show this webpage".

  Read the article

• Windows Server 2008 R2 DNS Server not working?

  - by wolfvilleian

  I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

  Read the article

• How can I launch RemoteApp on Windows Server from server itself at startup

  - by Rusted

  I have Windows Server 2008 R2 with RDS and custom desktop (GUI) application installed on the server. The app is started as RemoteApp on server by user from his desktop computer (or, sometimes, he can work from notebook over VPN). Some details about environment: the server automatically shuts down every evening and automatically power-on every morning (this is a requirement) desktop application do some precalculations/precaching on startup and it can take lot of time mentioned application have some memory leaks, so I can't use hibernate instead of shutdown When user launching this app from his computer, he can't start work with it until this app finishes pre-initialization. Is there any way to start RemoteApp session at the server startup (without actual user logon), so that the user could connect to this session from his computer later? I don't want to involve the user's computer to make it work. I have tried to do it by Windows startup script, but have no luck - starting RDP session requires actual user session.

  Read the article

• Automatically taken out of AD domain

  - by Mattias

  Hi Guys, arrived to work this morning just to find that I couldn't log on to my computer. As it turned out my computer had been "unjoined" from our domain. I am positive that I didn't "unjoin" manually yesterday before I closed the computer down. Have anyone experienced this behavior before and is it even possible? Or should I start getting nervous about anyone playing around on the serverside? I'm running my domaincontroller on a Windows2003 server and the client computer that got "unjoined" is a Windows 7 Ultimate.

  Read the article

• Dual monitor over network with Windows Host and Mac client?

  - by thegreyspot

  I'm looking for something like MaxiVista that lets you extend your monitor to a second computer monitor. However Maxivista is only Windows base. My main computer is Windows 7 and the other computer I'm trying to connect to is a Mac. Note I am not trying to share my keyboard or mouse, I want to use the Mac as a third display.

  Read the article

• Laptop overheating within minutes of start up

  - by Spik330

  I have a Dell Windows 7 Home Prem with an I7-720QM. More information on the computer can be found here http://www.dell.com/support/home/us/en/04/product-support/servicetag/51CVCN1/configuration The Problem I am having is the computer will over heat unnaturally fast. From the time it takes from boot to when i can run my diagnostic tools which takes about two minutes the cpu temp is 86c after a few more minutes the cpu temp will reach 100 and the computer will black screen shut down. In total the the laptop can only be run for 3-5 minutes before completely shutting off. During this time there is nothing extensive running. After the laptop shuts down you have to wait for it to cool down or it will shut off even faster sometimes 7-15 seconds well still in the boot screen. Does anyone know what could be the problem maybe a sensor or is the computer fried?

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc Computer B CANNOT connect as user Y to the server with mstsc! Error that username/password is incorrect. The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. EDIT: I tried: prefixing domain to the username prefixing the server computer name to the username change the password copy/paste the password from notepad to make sure it was correct I find it very strange.... EDIT: The computers are not on the same subnet as the server. The server is at my hosting provider. All computers as all users can reach the web app that is running on the server.

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Permissions needed to read event log messages remotely?

  - by Neolisk

  When running under a limited account, local event log messages are displaying fine, for remote computer I am getting this error: The description for Event ID ( xxxxx ) in Source ( yyyyy ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to retrieve this description; see Help and Support for details. The following information is part of the event: zzzzz. Same remote computer works fine under domain administrator. I am currently experimenting with just the Event Viewer, by using Run As. Original issue is a PowerShell script which does Get-EventLog. Are there any special permissions that need to be in place to able to read event log messages remotely? Supposedly there is a simple solution in Windows 2008 and higher, i.e. just add user to Event Log Readers group. Is there anything like that for Windows 2003?

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Join multiple filesystems (on multiple computers) into one big volume

  - by jm666

  Scenario: Have 10 computers, each have 12x2TB HDDs (currently) in raidZ2 (10+2) configuration, so, in the each computer i have one approx. 20TB volume. Now, need those 10 separate computers (separate raid groups) join into one big volume. What is the recommended solution? I'm thinking about the FCoE (10GB ethernet). So, buying into each computer FCoE (10GB ethernet card) and - what need more on the hardware side? (probably another computer, FCoE switch? like Cisco Nexus?) The main question is: what need to install and configure on each computer? Currently they have freebsd/raidz2, but it is possible change it into Linux/Solaris if needed. Any helpful resource what talking about how to build a big volumes from smaller raid-groups (on the software side) is very welcomed. So, what OS, what filesystem, what software - etc. In short: want get one approx. 200TB storage (in one filesystem) from already existing computers/storage. Don't need fast writes, but need good performance on reading data. (as a big fileserver), what will works transparently, so when storing data don't want care about onto what computer the data goes. (e.g. not 10 mountpoints - but one big logical filesystem). Thanks.

  Read the article

• How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

  - by Software Monkey

  I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

  Read the article

• Logon onto shared Windows account using individual passwords?

  - by Tom

  In a networked WinXP environment, I have a computer-controlled device which I want to connect to the network, but allow various people to use. The computer must be left running and logged on at all times. My thought is to run the computer under a "shared account" which would allow each user to logon/unlock the screen using their own network password (i.e., the password for their personal account). Is this possible? Thanks, Tom

  Read the article

• Is it possible to add hardware on a remote machine and use it as if it was installed on the local machine?

  - by that0th3rGuy

  Probably a silly question. We have two computers in the apartment running Windows 7 and Windows Vista. 99% of the time we use headphones but every now and then we have a desire for some ambiance so we got a set of 2.1 speakers. But now only one of us has access to the speakers unless we move them around every now and then. So I was wondering if it's possible to add the other computer's sound card as a hardware device on my computer so that I can configure, for instance, Winamp to play through the other computer's sound card, hence the speakers connected to the other computer.

  Read the article

• Can I format a usb stick on windows xp, in HFS+ format, and make the usb stick mac os x bootable?

  - by user717236

  My Intel Mac OS X computer is corrupt and I feel, at this point, I need to perform a fresh install of the OS. It consistently and automatically logs out, right after I log in. I tried logging in as the root. I tried safe boot and it wouldn't load. Anyway, the point is I want put the Mac OS X installer on a USB thumb drive and have it boot up on the Intel Mac OS X computer. Unfortunately, the computer is inaccessible, as I mentioned above. So, I have a Windows XP machine that I'm using and attempting to create a bootable USB thumb drive that's compatible with Mac OS X. I have tried transmac, macdrive, and paradox for windows -- all of which proved unable to format the usb stick in HFS+. How do I know this? Well, even though the Transmac reports that's been formatted to HFS+, Computer Management in Windows says otherwise: I even put the installer on the usb drive, after transmac reportedly formatted it properly, and the mac os x computer didn't even recognize that a USB thumb drive was inserted, via pressing the option key at boot-up time. I'm not sure what the problem is and how to actually format the drive. Can anybody offer any help? I would appreciate it. Thank you.

  Read the article

• Linux: disbale USB without disabling power

  - by Ergot

  TLDR I want toggle between the following usages of a usb-port via the terminal: use like a normal usb-port only supply energy to charge Story I recently got me something like a magna doodle that can save your drawings to pdf, which can be moved to your computer via usb afterwards. Now the thing is that you can't save anything while it's plugged in. Because it's the only way to charge it, it bugs me that I can't find a software solution and laziness I want to keep it plugged in and toggle the connection to the computer only when needed. I noticed that it's charging and usable when it is plugged in and the computer is shut down or suspened. So I guess that there's a way to do it. Tech info computer: ThinkPad X201 Linux Kernel: 3.14.5-1-ARCH "Magna doodle": Boogie Board Sync

  Read the article

• How to better copy&paste big files over RDP?

  - by WebMAOhist

  Recently I was making a few attempts to copy&paste a big (1.2 GB) file to remote computer over RDP. The remote computer is virtual testing machine with MS Windows Server 2008 Datacenter. First I tried to copy&paste before midnight when the transfer speed was limited by client computer ISP to 100 kB/s. So, it required a few hours and I was forced to cancel transfer since remote desktop became too unresponsive and sluggish (slow). So, I re-started it over midnight when my local transfer speed is over 4 GB/s 4MB/s (sorry for typo). So, my impression is that independently on speed (broadband) of copy&paste transfer the remote computer becomes sluggish while copying over RDP. At the same time downloading from internet doesn't make remote host sluggish. AFAIU, it is because clipboard of remote computer and so its memory becomes overloaded by transfer. How can I control (restrict) the usage of clipboard for specific process (pasting of file)? What are the possible way to control it? Update: After reading that slow speed of transfer is caused by encryption used for copy&pasting over RDP and since I believe I am more interested in overall efficiency: both the time, or rapidness, of getting file as well as possibility to work without waiting, I changed the question title from: How to control the usage of remote desktop clipboard usage for pasting a big file? to How to better copy&paste big files over RDP? For example, is it better to copy&paste one huge (zip) archive or unzip it and copy paste a folder with unzipped files? And more exactly I wanted to ask: What are possible ways to improve overall experience: the speed of transfer (i.e. availability of needed file) responsiveness of remote host (making remote coputer available for work before completion of copy&pasting)?

  Read the article

• Windows XP hanging on login screen

  - by Nathan W

  I have been given two Eee PC 100HA to manage for some people, they are both running the same hardware and XP home but one is having some strange problems with logging on. The main problem is that it hangs at the login screen for ages and sometimes never gets to the desktop. The strange thing is it only seems to do it after the computer has been cold started, but it won't do it if the computer has been restarted. I have made two logs of the start up with process monitor but every time the logger is attached the computer will log in fine. I have also set the computer to blue screen and create a crash dump when you press ctrl scroll twice but when I do it at the hung login it just sits at a black screen and I don't get a crash dump, I have turned off the auto system restart on failure option also. I can usually fix most computer start up and shutdown problems but this one has got me stuffed. Has anyone had the same problems before, or can recommend something that I can try? Cheers.

  Read the article

• Sound card problem, no audio device detected

  - by Paul

  I bought a new sound card because my built in sound card did not function. When I open YouTube, Media Player or anything that can create a sound my computer will hang up and sometimes when I start my computer it will hang when the Windows XP sound will activate. Update: My computer has no audio. It says NO AUDIO DEVICE. I already installed Realtek AC97 and Realtek High Definition Audio Driver and I also pasted stream.dll to the Windows and system32 folders and I restarted my computer but it still says NO AUDIO DEVICE. Please help me. Thanks

  Read the article

• Airport Express configuration

  - by Christina

  We are trying to set up remote access to a computer that houses a server fro a particular program we are running. The program says we need to configure the office router. In the firewall settings it says to open ports 5345-5351 (TCP only). Port Forwarding: You will also need to forward the same range of ports (5345-5351) to the computer running the Server. This typically requires that the computer running the Server be assigned a static IP on the local network. Having trouble figuring out which IP address we actually need to be using on the client side of this program in order to access the server computer. Can someone walk through this process?? We are working on Mac OSX 10.5. Thank you in advance!

  Read the article

• Sql-server-2008 client Access license

  - by thushya

  Hi, case 1 : i have one user makes 10 connection from single computer, maximum number of connection at a given time = 10, what is the number CAL i need here ? case 2 : i have 10 users have access to only 1 computer, 10 user connect from single computer - maximum connection at any given time = 1, what is the number CAL i need here ? case 3 : i have 10 users using 10 computers, all 10 are making total of 5 connection maximum in any given time, what is the number of CAL i need here ? Thanks.

  Read the article

• Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

  - by Synetech

  I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

  Read the article

• Is it safe to use a single switch for multiple subnets?

  - by George Bailey

  For a moment, forget about whether the following is typical or easy to explain, is it safe and sound? Internet | ISP supplied router x.x.x.1 (public subnet) | switch-------------------------------------+ | (public subnet) | (public subnet) BVI router (switch with an access list) NAT router | (public subnet) | (private subnet 192.168.50.1) +--------------------------------switch----+ (both subnets) | | computer with IP 192.168.50.2 ------+ +----computer with IP x.x.x.2 I don't plan to implement this setup, but I am curious about it. The 50.2 computer may send a packet to the x.2 computer, but it will use 50.1 as the router, since 50.2 knows that the subnet is different. Would this result in the packet being received twice by the x.2 machine, first directly through the switch, second by way of the two routers? Do you see any problems with this aside from how confusing it is, and that it would put one switch doing the work of two subnets?

  Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >