Search Results

Search found 10651 results on 427 pages for 'modem manager'.

Page 119/427 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

• How to set up a serial connection to a Windows 7 computer

  - by oli_arborum

  I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

  Read the article

• Extending home network using multiple access point originating from another access point

  - by cyberjar09

  I have a home network with the current setup (RJ45 running from main router to access point) : +-------------+ +--------------+ | 192.168.2.1 | |192.168.2.2 | | router +--------------->access point 1| +-----^-------+ +--------------+ | | +-----+--------+ | 192.168.1.1 | | modem | +-----^--------+ | | | | +--+--+ | ISP | +-----+ However I would like to extend the network to two more floors in the house via the existing Access Point (router is too far and not reachable using a network cable, hence I need to extend using current access point). Please see diagram below : +-------------+ +--------------+ +----------------+ | 192.168.2.1 | |192.168.2.2 | | 192.168.2.3 | | router +--------------->access point 1+----------> access point 2 | +-----^-------+ +--------+-----+ +----------------+ | | | | +-----+--------+ | | 192.168.1.1 | | | modem | | +-----^--------+ | +----------------+ | +----------------> 192.168.2.4 | | | access point 3 | | +----------------+ | +--+--+ | ISP | +-----+ Q1 : is this setup possible? Q2 : if possible, will I have to do anything different from what I did to setup access point 1? edit 1 : I am trying to study the dd-wrt documentation to see which would be the correct mode of operation for me Linking Routers but Im confused because I dont see any info on how to use an existing Access point to extend the signal of the SSID. If anyone could point me to the correct wiki for how I should setup AP2 and AP3 based on AP1, it would be very helpful. For AP1, I did the following Use static IP and setup same SSID as primary wireless router use same security as primary wireless router make AP1 point to 192.168.2.1 (primary router) for DHCP Thanks in advance.

  Read the article

• Usb device not working properly on a Thinkpad T60

  - by Xavierjazz

  I have just started getting a message that a USB device is not working properly. This is on a new Thinkpad T60 running Windows XP Professional SP3. I have had all devices attached for about 10 days or so. When I go to device manager there is no sign of a problem: everything is working correctly. I am unable to find out which device it is. I searched this forum but the only reference I found was to older computers which may not be Usb2 capable. This is not my problem. Any ideas? Thanks. EDIT: I realized I had a harddrive attached but turned off. Although I could not track down any error messages except the balloon that came up, I have disconnected it and, so far, no messages. We'll see over the next day or two, but this may be the problem. Thanks EDIT: This has not solved the problem. I get the message that one of the USB devices has malfunctioned and it points to "USB root hub (2 ports)" and shows an unused port and an unknown device. However, when I check my device manager, it says that there are no problems, everything is working as it should. ?? EDIT: I now found the event log view and there are 2 types of error messages. They do not relate to the time that I get the balloon. 2 of the 3 are "Ati2mtag" errors and the third is "System Control Manager". Are these related to my problem, and the balloon just pops up randomly? EDIT: well, I'm still having the problem, and have narrowed it down to a malfunctioning device. Thanks to all.

  Read the article

• Very strange networking problem in all computers in my house

  - by Anthony

  I have three computers in my house: One desktop (wired), and two laptops (wireless). I'm using Cox Communications (yes they suck), and yesterday they had a major outage. I know it was them because I called them up when I started losing connection to the internet. All the computers can connect just fine, but they don't have internet access. It just says "local only". The weird thing is, some of them work occasionally. For the first day my laptop was working perfectly, while all the other computers couldn't connect. Later on in the day it got reversed, and the desktop was the one with internet access. By the second day the problem on Cox's end was fixed, but we still had no access. I called them up and they reset my modem, and did the usual troubleshooting stuff. It never fixed the problem, but we found out that the problem had to do with conflicting IP addresses. My router was a Linksys WRT54G and it was about 5 years old. I figured it might have gotten damaged from the outage since it was so old, and now it's having trouble "fixing itself" and giving out the proper IP addresses. So I bought a new router, a Cisco Linksys E1000. I set everything up, and still the same problem. My computer has access right now (that's how I'm writing this), but no other computers seem to be able to get access. Is there possible damage to the modem? Can someone help me please? Sorry for this being so long.

  Read the article

• Correct way to set up office network - 8 workstations, a file server and a staging server

  - by naunu

  Our office had this old school windows 2003 domain setup, our server caught fire, and now we are looking to do it right from scratch. Here is what we need: 5 PC and 3 Mac workstations for web development, they will each have WAMP/MAMP setup on them, managed by their developers. We will have a file server for assets, and a LAMP server with an external IP for staging. Here is what we have to work with: 5 IP addresses, brand new PC file server with windows 2008 SE, D-Link DSS-16+ 16 port switch, belkin 5 port wireless router, cable modem with 4 ports. How I have it set up now (this is a temporary makeshift setup): Cable modem = LAMP server, wireless router Wireless router = Switch = All of the workstations and file server (setup as a workgroup). We have noticed our internet is very slow with us all plugged in to the switch, and the switch plugged in to the router. I am not positive, but I think it is because our router does not have NAT. We are also having problems with the MACs connection to the network drive - it keeps disconnecting. I want this done right, and we have a ~$600 budget to buy anything else we need. Does anybody have any advice for me? Should I set up a domain or workgroup?

  Read the article

• sysctl.conf not running on boot

  - by Brian

  At what point is sysctl.conf supposed to be read during boot, and why might it not be running? I have the following settings which are not being applied when I reboot: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 fs.nfs.nlm_udpport = 32768 fs.nfs.nlm_tcpport = 32768 The first section is needed for KVM bridging, and the second is to run the NFS lock manager on a known port. However, after booting, these values have not taken effect. If I run sysctl -p, then they do. This wouldn't be a huge issue, except that I can't figure out how to restart the lock manager without rebooting. I would really like to know why sysctl.conf isn't working at boot, but I'd settle for just being able to restart the lock manager. This is on Ubuntu server 10.04.2, kernel 2.6.32-31-server. I know some daemons check the permissions on their config files and refuse to work if they're too permissive, but sysctl.conf is 644 root:root, which I'm pretty sure is the default.

  Read the article

• OpenVPN, install a TAP adapter

  - by GolezTrol

  When I try to connect to my work VPN using OpenVPN, the connection fails with the message: All TAP-Win32 adapters on this system are currently in use. Many sources suggest to look in Control Panel\Network and Internet\Network Connections an enable the TAP adapter, but when I look there, there is none. Now I've run addtap.bat which is provided with OpenVPN, but I still don't get to see any TAP adapter, and logging in in VPN still fails. The output of addtap.bat is C:\Windows\system32>"C:\Program Files (x86)\OpenVPN\bin\tapinstall.exe" install "C:\Program Files (x86)\OpenVPN\driver\OemWin2k.inf" tap0801 Device node created. Install is complete when drivers are updated... Updating drivers for tap0801 from C:\Program Files (x86)\OpenVPN\driver\OemWin2k .inf. Drivers updated successfully. I've Run As Administrator both the setup of OpenVPN and addtap.bat. I've run deltapall.bat to remove any (maybe hidden) adapters. It said it removed three of them, after which I ran addtap.bat again to try to create another one. I also run OpenVPN itself as administrator. What's wrong? Running Windows 7 Home Premium on a HP Pavilion dv7 4050ed. It has worked before, but I recently had to reinstall my laptop, for which I used the restore disks I created when I just got it. Everything else seems to work fine. == UPDATE == The TAP adapter is found in Device Manager, but apparently it is disabled because it is incompatible with Windows 7 64bit. I've deïnstalled OpenVPNGui, downloaded a version that should be 64bit compatible, and installed that. Still no cigar. Then I found a tip to install OpenVPN (version 9) after installing OpenVPNGui, because that installs OpenVPN version 8. Now I got a v9 TAP driver in Device Manager, but it still doesn't work and shows up in device manager with an exclamation mark, and not at all in my network devices.

  Read the article

• only port working with mod_proxy is 8009, trying to use with tomcat and httpd, dont know why

  - by techsjs2012

  I am trying to use mod_proxy with httpd and tomcat. If I leave tomcat ajp to run on 8009 in the server.xml of tomcat and in the httpd.conf of apache httpd everything works great but once I change it to anything else and restart them both it does not work.. I trieded 8109,8209 and 8019.. only thing that works is 8009? Below is my setup that works. <Proxy balancer://testcluster stickysession=JSESSIONID> BalancerMember ajp://127.0.0.1:8009 min=10 max=100 route=node2 loadfactor=1 </Proxy> ProxyPass /examples balancer://testcluster/examples <Location /balancer-manager> SetHandler balancer-manager AuthType Basic AuthName "Balancer Manager" AuthUserFile "/etc/httpd/conf/.htpasswd" Require valid-user </Location> if I change the port to anything in here and the server.xml of tomcat it does not work but I can telnet the port so I know its up? below are the other libs settings I have LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so #LoadModule proxy_ftp_module modules/mod_proxy_ftp.so #LoadModule proxy_http_module modules/mod_proxy_http.so #LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so

  Read the article

• network latency, TCP and UDP packets

  - by user115848

  Hello recently my network has started to cause me lots of problems. I have a cable modem, connected to a tp-link router (with some port forwarding). Everything was working fine then i started to get lots of udp (port 53) "UNREPLIED" logs in the router. Now there are tcp UNREPLIED logs too. This is causing lots of latency and failed connections when trying to connect to different internet sites. Also, we run an openfire server for spark connections, and I believe its causing connectivity issues for some users who are trying to connect using Spark (some people connect fine, others don't). Please see screen shot below for packet logs. It has to be something internally, as I connected straight to the comcast modem and i was able to connect to the internet and various sites as normal. I tried to swap out the router with a different and got the same issue. I scanned both my internal dns servers for viruses or malware and it came up empty. Another anomaly is that when i try to connect to www.cnn.com, i get redirected to the different site. I scanned my own machine for hijacks. Not sure if this is related to the networking issue. Please let me know if you have any ideas for troubleshooting.

  Read the article

• Need help to configure file:default on apache2

  - by turk182

  hi all!! im trying to use xen on ubuntu 8.04 hardy heron, because it is a project that assign to me in my new job, i have already installed xen and im running the virtual machines. according to the guide that they give me, i have to configure de file: default, from apache2 directory, like this: vi /etc/apache2/sites-available/default inside of this file i have to write the next information: NameVirtualHost * VirtualHost * ServerName "www".ejemplo.com ServerAlias ejemplo.com DocumentRoot /var/www/ ProxyRequests Off Proxy * Order deny,allow Allow from all /Proxy ProxyPass /balancer-manager ! ProxyPass / balancer://mycluster/ stickysession=BALANCEID nofailover=On ProxyPassReverse / "http"://http1.ejemplo.com/ ProxyPassReverse / "http"://http2.ejemplo.com/ Proxy balancer://mycluster BalancerMember "http://10.10.2.101:8080 loadfactor=1 BalancerMember "http://10.10.2.102:8080 loadfactor=2 ProxySet lbmethod=byrequests /Proxy Location /balancer-manager SetHandler balancer-manager Order deny,allow Allow from all /Location /VirtualHost in the section of balancermember im using the ip of the virtual machine: virtual machine 1 has ip 10.10.2.101 and virtual machine 2 has ip 10.10.2.102 then i have to install apache2 on each virtual machine and restart apache2 the question is what i hace to do to verify if all of this works allegedly i have to open a browser and write "www.ejemplo.com" and suppost show something thats the reason that im ask for help cause i dont know what to do, im looking for on the web and i cant find nothing related with this... ill appreciatte your help. THXS!!! pd. i closed "www" and "HTTP" in quotes by rules of this sites cause im a new user

  Read the article

• DriveImage XML fails with a Windows Volume Shadow Service Error

  - by ssvarc

  I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

  Read the article

• SQUID proxy - open FTP (and other ports)

  - by gaffcz

  elpeHow can I open other ports than HTTP and HTTPS using SQUID proxy? I have last version of squid running on Fedora 10 but I'm not able to open FTP port. part of my squid.conf: acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 acl ftp proto FTP acl ftp_port port 21 always_direct allow FTP acl SSL_ports port 443 20 21 22 acl Safe_ports port 20 # ftp acl Safe_ports port 21 # ftp acl Safe_ports port 22 # sftp acl Safe_ports port 80 # http acl Safe_ports port 280 # http-mgmt acl Safe_ports port 443 # https acl Safe_ports port 1025-65535 # uregistred ports acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager # USER privilegies (encoded in file passwd) auth_param basic program /usr/lib/squid/ncsa_auth /etc/squid/passwd acl AUTHUSERS proxy_auth REQUIRED # BLACKLIST (in file denied.conf) acl denied_domains dstdomain "/etc/squid/DNDdomains.conf" acl denied_regex url_regex "/etc/squid/DNDregex.conf" http_access deny denied_regex http_access deny denied_domains http_access allow AUTHUSERS http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow ftp_port CONNECT http_access allow ftp http_access allow localhost http_access deny all #http_reply_access allow all #http_access allow all http_port 3128 hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid 10000 16 256 coredump_dir /var/spool/squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 I've tried to add: acl ftp proto FTP / acl ftp_port port 21 http_access allow ftp add/remove ports 20,21 from SSL_PORTS list set the iptables But nothing helped. It is even possible to use a new version of squid for FTP transfer?

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Private staff network within public network

  - by pianohacker

  I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

  Read the article

• Enabling JMX for proxool with tomcat

  - by dialt0ne

  I am trying to get proxool's MBeans available so that I can see/manipulate them with jconsole. I have jconsole working, but I don't see anything related to proxool. The system is using Sun Java 1.5.0_17 (I know, I know... I'm working with the developers to upgrade). JMX is enabled by modifying $JAVA_OPTS in my tomcat 5.5 startup script: SJO="$SJO -Dcom.sun.management.jmxremote" SJO="$SJO -Dcom.sun.management.jmxremote.port=4998" SJO="$SJO -Dcom.sun.management.jmxremote.authenticate=false" SJO="$SJO -Dcom.sun.management.jmxremote.ssl=false" JAVA_OPTS="$JAVA_OPTS $SJO" I have proxool configured with JNDI in server.xml: <GlobalNamingResources> <Resource name="jdbc/database" auth="Container" type="javax.sql.DataSource" factory="org.logicalcobwebs.proxool.ProxoolDataSource" user="username" password="password" proxool.driver-url="jdbc:oracle:thin:@fqdn.example.com:1521:MYSID" proxool.driver-class="oracle.jdbc.driver.OracleDriver" proxool.alias="mysid" proxool.maximum-connection-count="20" proxool.statistics="20s,5m,15m" proxool.statistics-log-level="INFO" proxool.jmx="true" proxool.verbose="true" /> </GlobalNamingResources> My test .jsp can run queries and I can see it using the connections with the proxool admin servlet, but I'm unsure if there's more I need to configure in tomcat or proxool to get JMX functioning. Advice? jmxproxy info edit: The jmxproxy servlet is working - when I go to the URL http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=*:type%3DRequestProcessor,* the results are: OK - Number of results: 2 Name: Catalina:type=RequestProcessor,worker=http-8080,name=HttpRequest0 modelerType: org.apache.coyote.RequestInfo bytesSent: 0 requestBytesSent: 0 contentLength: -1 bytesReceived: 0 requestProcessingTime: 1297983483666 globalProcessor: org.apache.coyote.RequestGroupInfo@32dc51c8 requestBytesReceived: 0 serverPort: -1 stage: 0 requestCount: 0 maxTime: 0 processingTime: 0 errorCount: 0 Name: Catalina:type=RequestProcessor,worker=jk-127.0.0.1-8009,name=JkRequest794 modelerType: org.apache.coyote.RequestInfo virtualHost: tomcatserver.example.com bytesSent: 0 method: GET remoteAddr: 172.30.3.51 requestBytesSent: 0 contentLength: -1 workerThreadName: TP-Processor15 bytesReceived: 0 requestProcessingTime: 9 globalProcessor: org.apache.coyote.RequestGroupInfo@1e7d3b8e protocol: HTTP/1.1 currentQueryString: qry=*%3Atype%3DRequestProcessor%2C* requestBytesReceived: 0 serverPort: 4999 stage: 3 requestCount: 0 maxTime: 0 processingTime: 0 currentUri: /manager/jmxproxy/ errorCount: 0 And more to the point http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=Catalina:type%3DEnvironment,resourcetype%3DGlobal,name%3DProxool yields: OK - Number of results: 0

  Read the article

• What kernel modules are required for wi-fi to work?

  - by Leonid Shevtsov

  My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• Timeout option not working on efi windows 7/windows8 dual boot machine

  - by Guenter

  I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

  Read the article

• Resolving loss of internet bandwidth in home network

  - by Caspar

  Recently, I've decided to connect my laptop at home to my modem/router through Ethernet cables built into my apartment. As these built-in Ethernet cables are usable via plugs built into the walls (called powerline adapters), I use some additional cabling (STP CAT6 cables) from my laptop/router to the plugs. In addition, I don't know any technical details about these built-in cables (as they're not visible), only the maximal bandwidth (1 GBit = Cat6?) that they're supporting. The built-in cables are Cat. 5e Ethernet cables. The problem is now that when I set up the connection, I cannot use the full bandwidth that my internet connection is actually offering (100 Mbit/s), only about 85 Mbit/s between 85 - 88 Mbit/s, despite the fact that all cables involved should support the maximal bandwidth. I know from other tests with one of the Ethernet cables in use that I can use almost 99 Mbit/s when I connect my laptop directly to the router/modem using only this one cable. In addition, it is very unlikely that the length of the resulting cable connection from my laptop to my router involving the built-in cables exceeds 100 m. So, what possible reasons for this loss of bandwidth exist? And how I can fix this issue? I hope this might help resolve the issue: The built-in cables appear to be Cat. 5e Ethernet cables. So, is there any problem when I connect Cat6 Ethernet cables directly to Cat5e Ethernet cables via the plugs?

  Read the article

• What kernel modules are required for wi-fi to work?

  - by Leonid Shevtsov

  My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

  Read the article

• Tridion 2011 SP1 Core Service - expose to live server within PROD env

  - by Neil

  We have a requirement to allow our users to submit information about their "projects" - a small piece of text and single image they upload. Ultimately we'll have a listing page of user contributed projects that others can comment on and rate. We've decided to user Tridion's UGC for rating & comments site-wide for this first phase which has got me thinking - UGC is tied to Tridion published pages & components, if we want UGC on our user-submitted projects, they'll have to be created within Tridion as components themselves, not be sat in some custom db table? Is this where the Core Service could come in? My understanding is that the CD Web Service is for retrieval, not for interacting with the Content Manager. Is it OK (!) architecturally to expose the Core Service only to our live application servers so our backend .NET code can create "project components" that can be then be published by editors allowing them to be commented on? Everything sounds pretty neat and tidy apart from the "exposing Core Service to live servers" bit. Without this though I'd have to write a custom way to "transfer" it back over to the Content Manager - maybe like Audience Manager Sync works? Anyone done this before?

  Read the article

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• Cant access folder on server- Permission denied

  - by Michal Korzeniowski

  I am running a vps with ubuntu 11.04. After a clean Modx install I've tried to access http://www.encepence.pl/manager and I've got a permission denied by my server. the thing is that I can easily access any other folder under that domain and modify this folder(manager) content via ftp. I’ve tried modifying virtual host with that <Directory /var/www/blackflow/data/www/encepence.pl/manager/> Options Indexes FollowSymLinks ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> But it didn't work. <Directory /var/www/blackflow/data/www/encepence.pl> Options -ExecCGI -Includes php_admin_value open_basedir "/var/www/blackflow/data:." php_admin_flag engine on </Directory> <VirtualHost 192.166.219.34:80 > ServerName encepence.pl CustomLog /var/www/httpd-logs/encepence.pl.access.log combined DocumentRoot /var/www/blackflow/data/www/encepence.pl ErrorLog /var/www/httpd-logs/encepence.pl.error.log ServerAdmin [email protected] ServerAlias www.encepence.pl SuexecUserGroup blackflow blackflow AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/var/www/blackflow/data:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/var/www/blackflow/data/mod-tmp" php_admin_value session.save_path "/var/www/blackflow/data/mod-tmp" VirtualDocumentRoot /var/www/blackflow/data/www/%0 </VirtualHost> Any ideas on what might have gone wrong?

  Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >