Search Results

Search found 16987 results on 680 pages for 'second'.

Page 119/680 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

• Struggling to set-up NLB cluster

  - by Chris W

  I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

  Read the article

• Restricting memory area for linux kernel

  - by user1066789

  I am running ltib linux on P1022RDK (P1022 Core) platform. I have 512 MB = 0x20000000 memory. I want my linux kernel to use second half of the board memory (i.e from 256 MB to 512 MB) and want first half of memory to be reserved for some other purpose. For this I am building linux kernel using ltib. For that purpose I am setting following kernel configuration. Please suggest if I am doing it the right way. CONFIG_LOWMEM_SIZE = 0x10000000 # 256 MB CONFIG_PHYSICAL_START = 0x10000000 # Starting from 256MB (second half of memory) On the Uboot I am loading the kernel as following way setenv loadaddr 0x11000000 # Kernel base = 0x10000000 + 0x01000000 (offset) setenv fdtaddr 0x10c00000 # Kernel base = 0x10000000 + 0x00c00000 (offset) bootm $loadaddr - $fdtaddr My kernel Load address is 0x10000000 & kernel entry point is 0x10000000 Doing above configuration / steps my kernel stuck at following on Uboot ## Booting kernel from Legacy Image at 11000000 ... Image Name: Linux-2.6.32.13 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 3352851 Bytes = 3.2 MB Load Address: 10000000 Entry Point: 10000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 10c00000 Booting using the fdt blob at 0x10c00000 Uncompressing Kernel Image ... OK ================ >> It should uncompress FDT here & continue ============== Any thoughts ?

  Read the article

• Restricting memory area for linux kernel

  - by user1066789

  I am running ltib linux on P1022RDK (P1022 Core) platform. I have 512 MB = 0x20000000 memory. I want my linux kernel to use second half of the board memory (i.e from 256 MB to 512 MB) and want first half of memory to be reserved for some other purpose. For this I am building linux kernel using ltib. For that purpose I am setting following kernel configuration. Please suggest if I am doing it the right way. CONFIG_LOWMEM_SIZE = 0x10000000 # 256 MB CONFIG_PHYSICAL_START = 0x10000000 # Starting from 256MB (second half of memory) On the Uboot I am loading the kernel as following way setenv loadaddr 0x11000000 # Kernel base = 0x10000000 + 0x01000000 (offset) setenv fdtaddr 0x10c00000 # Kernel base = 0x10000000 + 0x00c00000 (offset) bootm $loadaddr - $fdtaddr My kernel Load address is 0x10000000 & kernel entry point is 0x10000000 Doing above configuration / steps my kernel stuck at following on Uboot ## Booting kernel from Legacy Image at 11000000 ... Image Name: Linux-2.6.32.13 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 3352851 Bytes = 3.2 MB Load Address: 10000000 Entry Point: 10000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 10c00000 Booting using the fdt blob at 0x10c00000 Uncompressing Kernel Image ... OK ================ It should uncompress FDT here & continue ============== Any thoughts ?

  Read the article

• Unable to connect to cable modem when connected to VPN

  - by Spuas

  the scenario is as follows: First I have a cable modem which gives the internet connection. The network is 192.168.0.0/24 and its IP is 192.168.0.1 Second line, I have a router connected to the cable modem. Its "outside" IP is 192.168.0.12. This router creates network 192.168.123.0/24 and its IP there is 192.168.123.254. My computer is wired to the router with IP 192.168.123.126. At this point I am able to access both devices web interfaces by their IPs on a browser (192.168.123.254 for the router and 192.168.0.1 for the cable modem). The problem I have is when I connect to a VPN from the computer. Then I am connected to a second network 10.0.0.0/24 and I get IP 10.0.0.200 (along with 192.168.123.126). I can connect to the router but then I loose connectivity to the cable modem: I cannot acces it through the browser, neither making a ping to it or a tracert. I have tried to add a new route to the windows routes by typing route ADD 192.168.0.1 MASK 255.255.255.0 192.168.123.254 but I cannot access it anyway... Am I missing something on the route adding? Which is the propper way of doing this? Thanks

  Read the article

• Why do I often have to refresh pages I navigate to once for them (or content in them) to load?

  - by GetOutOfBox

  I have noticed a bizarre pattern when using my PC, that when I open a link to a website, it often will often take a very long time to load, or time out. Sometimes content on the website will be drawn, but again, it seems to get "stuck" for an unusual amount of time before finishing. Most affected is Youtube; almost every time I navigate to a youtube video from another website such as Google, the video will not begin playing, but will instead just display the player controls with a black screen where the video should be and the buffering symbol, usually before displaying an error such as "The video failed to load". The unusual part of this problem is that whenever this happens, refreshing the page always causes it to load almost immediately the second time around, without any problems. Note that I'm not talking about how some browsers will dump whatever has been cached to the "pallet" briefly when the page is refreshed or loading stopped; but that the second time loading the website being faster. I have done my best to rule out some of the obvious causes: My Windows 7 desktop computer is the only device that seems to be affected. I use Firefox on it (latest version, flash updated, etc). My connection has more than enough bandwidth (30 megabits down, 4 up), and I've even tried QoSing all other devices to make sure this isn't happening due to usage spikes. Wireshark is not showing any clearly unusual network activity (i.e frequently dropped packets).

  Read the article

• How do I force a server to leave a SharePoint farm

  - by Stefan

  I have two web servers in a SharePoint (WSS 3.0) farm with one database server for the config and content databases. I already moved my content databases to a new database server successfully. But when I tried to move the sharepoint config database using the "stsadm deleteconfigdb" and "stsadm setconfigdb" commands, one of my servers got stuck in an intermediate state. I was able to join one of the web servers with the config database on the new server, but the other server is not able to join because it believes it is already part of the farm (which it used to be, before the move). On the central administration it says the status of the services on the server is "stopping". Even after rebooting all servers involved, uninstalling SharePoint and what not, this status does not change, and because of it, I am not able to join the second server with the new config database. I get random error messages when trying to join the farm. I believe that if I can unstuck this server, it will be able to join the farm again. The farm believes the second server is already part of it, but the web server itself knows its not. Any ideas on how to forcefully kick out a server from the farm?

  Read the article

• How to run a website domain without redirecting if IP is already used for another website? [duplicate]

  - by SSpoke

  This question already has an answer here: Hosting multiple distinct folders for distinct domains 1 answer I bought a VPS Host that gave me only 1 IP Address which I used on my first domain name and it works without any problems. Now my second domain name I can't use the same ip address as it points to the first domain name. So I figured my only option was to use a GoDaddy hosted iframe redirection which redirects to a sub folder on my first domain which worked so far. Now I'm trying to load paypal from <?php headers() ?> and I get a permission error because of that iframe Refused to display 'https://www.paypal.com/cgi-bin/webscr?notify_url=&cmd=_cart&upload=1&business=removed&address_override=1' in a frame because it set 'X-Frame-Options' to 'SAMEORIGIN'. How do I avoid the Iframe solution for my second domain while not messing up my first domain? Somebody I forgot once told me it doesn't matter if you have 1 IP Address you could host multiple websites on it? how it that possible the DNS doesn't seem to work off ports afaik, yes I could host multiple websites on different folders but that's not what I call hosting a real website it has to be pointed by a domain name, so this iframe issue doesn't happen My server configuration is httpd (apache) that comes with CentOS 6 (Linux) operating system

  Read the article

• Linux Tuning for High Traffic JBoss Server with LDAP Binds

  - by Levi Stanley

  I'm configuring a high traffic Linux server (RedHat) and running into a limit I haven't been able to track down. I need to be able to handle sustained 300 requests per second throughput using Nginx and JBoss. The point of this server is to run checks on a user's account when that user signs in. Each request goes through Nginx to JBoss (specifically Torquebox with JBoss A7 with a Sinatra app) and then makes an LDAP request to bind that user and retrieve several attributes. It is during the bind that these errors occur. I'm able to reproduce this going directly to JBoss, so that rules out Nginx at least. I get a variety of error messages, though oddly JBoss stopped writing to the log file recently. It used to report errors about creating native threads. Now I just see "java.net.SocketException: Connection reset" and "org.apache.http.conn.HttpHostConnectException: Connection to http://my.awesome.server:8080 refused" as responses in jmeter. To the best of my knowledge, I have plenty of available file handles, processes, sockets, and ports, yet the issue persists. Unfortunately, I have very little experience tuning servers. I've found a couple useful documents - Ipsysctl tutorial 1.0.4 and Linux Tuning - but those documents are a bit over my head (and just entering the the configuration described in Linux Tuning doesn't fix my issue. Here are the configuration changes I've tried (webproxy is the user that runs Nginx and JBoss): /etc/security/limits.conf webproxy soft nofile 65536 webproxy hard nofile 65536 webproxy soft nproc 65536 webproxy hard nproc 65536 root soft nofile 65536 root hard nofile 65536 root soft nproc 65536 root hard nofile 65536 First attempt /etc/sysctl.conf sysctl net.core.somaxconn = 8192 sysctl net.ipv4.ip_local_port_range = 32768 65535 sysctl net.ipv4.tcp_fin_timeout = 15 sysctl net.ipv4.tcp_keepalive_time = 1800 sysctl net.ipv4.tcp_keepalive_intvl = 35 sysctl net.ipv4.tcp_tw_recycle = 1 sysctl net.ipv4.tcp_tw_reuse = 1 Second attempt /etc/sysctl.conf net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 net.core.netdev_max_backlog = 30000 net.ipv4.tcp_congestion_control=htcp net.ipv4.tcp_mtu_probing=1 Any ideas what might be happening here? Or better yet, are there some good documentation resources designed for beginners?

  Read the article

• Windows 7 blank dvi screen

  - by user99

  I've just upgraded to Windows 7 Ultimate 64 bit. I had an issue during installation; after setup rebooted instead of going to the 'Completing installation' screen I just got a blank screen. I eventually(!) figured out that this meant 'un-plug your second monitor to proceed'. When I did this, installation completed in a snap and everything runs fine. However, whenever I plug my second monitor into my PC, it gets no signal, the the primary monitor removes all windows. icons, the taskbar and the cursor just shows the desktop wallpaper. I'm running a GTS8800 512mb, with the latest drivers (197 IIRC). The monitors are identical, and both plug into DVI sockets on the graphics card, the only difference is I connect one using a straight DVI cable and the other using a VGA cable and a VGA-DVI converter. It's the DVI cabled one that has the issues (if I plug it in by itself it gets no signal). Everything was working fine before I upgraded to Windows 7 (I used to run XPSP2). Anyone have any ideas?

  Read the article

• How do I calculate clock speed in multi-core processors?

  - by NReilingh

  Is it correct to say, for example, that a processor with four cores each running at 3GHz is in fact a processor running at 12GHz? I once got into a "Mac vs. PC" argument (which by the way is NOT the focus of this topic... that was back in middle school) with an acquaintance who insisted that Macs were only being advertised as 1Ghz machines because they were dual-processor G4s each running at 500MHz. At the time I knew this to be hogwash for reasons I think are apparent to most people, but I just saw a comment on this website to the effect of "6 cores x 0.2GHz = 1.2Ghz" and that got me thinking again about whether there's a real answer to this. So, this is a more-or-less philosophical/deep technical question about the semantics of clock speed calculation. I see two possibilities: Each core is in fact doing x calculations per second, thus the total number of calculations is x(cores). Clock speed is rather a count of the number of cycles the processor goes through in the space of a second, so as long as all cores are running at the same speed, the speed of each clock cycle stays the same no matter how many cores exist. In other words, Hz = (core1Hz+core2Hz+...)/cores.

  Read the article

• How to debug slow queries in Django+Postgres

  - by lacker

  My database queries from Django are starting to take 1-2 seconds and I'm having trouble figuring out why. Not too big a site, about 1-2 requests per second (that hit Django; static files are just served from nginx.) The thing that confuses me is, I can replicate the slowness in the Django shell using debug mode. But when I issue the exact same queries at an sql prompt they are fast. It takes about a second for a query to return, but when I check connection.queries it reports the time as under 10 ms. Here's an example (from the Django shell): >>> p = PlayerData.objects.get(uid="100000521952372") >>> a = time.time(); p.save(); print time.time() - a 1.96812295914 >>> for d in connection.queries: print d["time"] ... 0.002 0.000 0.000 How can I figure out where this extra time is being spent? I'm using Apache+mod_wsgi in daemon mode, but this happens with just the django shell as well, so I figure it is not apache-related.

  Read the article

• SQL 2008 SP1 crashing almost daily

  - by matijake

  Hey, almost every day our new DB crashes. It is virtual server residing on same hardware as 5 other servers, two of them beeing identical MS SQL2008sp1 and two Oracle 11g's so I can pretty much rule out hardware issues. Server has dedicated local LUN, 4vCPU and 8GB memory with 2GB windows swap file. It runs 4 instances. Primary instance is limited to 5GB memory and paralelism set to 4 running on MS SQL 2008 SP1 @ Windows Server 2008 Enterprise R2 x64. Only that primary instance is crashing. After it crashes nothing can connect to it, it's even impossible to shut it down through service manager. What I found in logs is: ***Stack Dump being sent to C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\LOG\SQLDump0081.txt SqlDumpExceptionHandler: Process 4788 generated fatal exception c0000005 EXCEPTION_ACCESS_VIOLATION. SQL Server i s terminating this process.     Whole log can be seen at: http://kabl.org/files/SQLDump0081.txt second crash log made second later at: http://kabl.org/files/SQLDump0082.txt I have analyzed mini crashdump with Microsoft tools, but no promising results. If it can help, here it is: http://kabl.org/files/SQLDump0081.mdmp Any ideas are greatly welcome, since it is becoming quite a pain in the ass to restart server almost every day :) Regrads, -Matija

  Read the article

• Why are my socks proxies slow

  - by vps_newcomer

  I have a linux vps, and i have tried a few socks proxy setups to test their performance: All tests were using speedtest.net The standard ssh tunnel proxy 0.8mbit/s download and 0.1-0.2mbit/s upload speeds dante-server proxy 1.3mbit/s download and 0.4-0.5mbit/s upload I am wondering why are these speeds so slow? Is anything shaping them? Is it just the nature of socks proxies? I know that the ssh tunnel has to do encryption and what not so that is why its slow, but i was surprised to see that the second setup was also quite slow. On the VPS i have received download speeds of 25MB/s per second (thats about 200mbit/s and upload speed of atleast 5MB/s (haven't got a good enough pipe to test anything faster). The other option i was going to try is to setup OpenVPN and see how that goes, however i need to find a good tutorial as it's fairly complicated to setup. So why is it so slow? How can i test to see where the bottleneck is? How can i make it faster :D

  Read the article

• Constant beeping

  - by Bogi Juul Peterson

  My computer has a problem with beeping. I'll first tell you how it started: One night I decided to watch a cartoon, and I took some water and food with me to eat while I watch. I fell asleep and when I woke up I had spilled water all over my keyboard. I didn't react quickly, because it went unnoticed for about 1 and a half hours. When I noticed, I quickly put my laptop on a radiator to try to dry it. When I turned the computer on there was a constant beeping sound. I didn't know what caused it, and I'm still not sure, but I think it has something to do with the USB hub. If I let the computer stand for some hours without any USB connections, it's fine, but when I put any kind of USB device in, it starts beeping. The laptop keyboard doesn't work so I have to have some kind of USB device connected to use the computer. The beeping is going on while I'm writing this and it makes my computer lag so much that it can make delays from the keyboard be from 1 second to 10 seconds. I need this computer because I don't have the money to buy a new one, and I have to use this computer for homework and games. The beeping is constant, with less than a second between beeps. If anyone has a solution, please help.

  Read the article

• Windows Server 2008 (Web Server) Replication

  - by justjoshingyou

  We have a load balanced environment with Windows Server 2008. What are some best practices to setting up replication across the web servers? Do I only want to replicate the web folders? How about replicating IIS changes - or do I need to make IIS changes on every server? I've never, ever set up replication, but I have worked with a web farm that used it before. Basically, I only know the basics about how it works, and am looking for any advice, guides, warnings, etc on setting this up. If you'd like to offer any advice, I'll let you know how our environment is for now. We have 1 prod server up and the second is nearly ready to go. We are using a cloud system and all machines are VM's. I am in the process of setting up the domain controller now (as I need to have one for DFS). Any ideas on the best way to go about setting up replication? Should we just stick the prod server in from the start or set up using a test VM and our second server and then switch it up later? I do not want to risk overwriting our prod server. Thanks!

  Read the article

• Merging cuesheet chapter halves into single track for an audiobook

  - by TheSavo

  I have an audiobook that I have ripped and I need some help constructing chapters. I have already made some cue sheets TITLE "Bookname" PERFORMER "the Author" FILE "File1.FLAC" wave ; 23971906.667 milliseconds TRACK 01 AUDIO TITLE "_Intro" INDEX 01 00:00:00 TRACK 02 AUDIO TITLE "CH 01" INDEX 01 24:15:50 TRACK 03 AUDIO TITLE "CH 02" INDEX 01 66:21:00 TRACK 04 AUDIO TITLE "CH 03" INDEX 01 87:05:00 The audio book is in two files. The chapter at the end of the first file is continued in the second file. However, the second file restates: The publisher Book Title List item Blah blah blah I would like to merge the two 'halves' of the chapter in one seamless track. The only way I can think to do this would be be: Bulk cut down the tracks. Drop the junk info into junk track Continue the track listings as normal Take the two "halves" of the target chapter and build a separate cue sheet for it. I know there has to be an easier way. I am ok with making the 'junk' info a 'gap' or something. These are are FLAC files that will be converted to MP3 for my phone and other potable devices. I have read the primers on cue sheets, but I am just not getting it.

  Read the article

• How to move my data from my old MacBook Pro to my new one?

  - by Tim Büthe

  I just purchased a new MacBook Pro and already got an 2008 model. I wonder how I move all my data over to the new one. My first idea was, to use my Time Machine backup and restore from it, which seems to be a good idea and should work just fine regarding to this link: http://blog.duncandavidson.com/2008/01/restoring-from-time-machine.html. But, since my current MacBook got older Software on it, like iLife '08 instead of iLife '09 I would have to upgrade this afterwards. Is this correct, or does Time Machine does some magic to exclude well known software? And is it possible to reinstall or upgrade iLife with the included installation DVDs? My second idea is, to just swap the hard drives instead of using the Time machine backup. If it is not too complicated to remove the hdd, this should be the fastest way. This also has the benefit, that the 2008er MacBook then contains a brand new installation and I don't have to remove all my stuff or reinstall Mac OS before I give it away. My question on that second idea would be: does snow leopard handle this stuff correctly? I reboot with the new hardware and all just works fine? So in a nutshell: What would you do: restore from backup or swap drives? And what about the new software?

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• Server unreachable without www

  - by deamon

  My server is unreachable without "www." prefix, even when trying it with ping. The DNS entry looks like this: $TTL 86400 @ IN SOA ns1.first-ns.de. postmaster.robot.first-ns.de. ( 2011010600 ; serial 14400 ; refresh 1800 ; retry 604800 ; expire 86400 ) ; minimum @ IN NS robotns3.second-ns.com. @ IN NS robotns2.second-ns.de. @ IN NS ns1.first-ns.de. @ IN A 1.2.3.4 localhost IN A 127.0.0.1 mail IN A 1.2.3.4 www IN A 1.2.3.4 ftp IN CNAME www imap IN CNAME www loopback IN CNAME localhost pop IN CNAME www relay IN CNAME www smtp IN CNAME www @ A DNS record of the same type for another domain on the same server is working with and without "www". And the VirualHost config looks like this: <VirtualHost *:80> ServerName somewhere.com ServerAlias www.somewhere.com ServerSignature Off ... </VirtualHost> Any idea what could be wrong?

  Read the article

• Outlook certificate error and separate send/receive error

  - by Richard

  I run a laptop with Vista 32bit and MS Office 2010. Outlook has two profiles, both configured as POP3/SMTP and neither go through an exchange server. Recently, one of the mail servers (hosted with easily) was getting full, so I changed the profile setting to delete from the server if mails are older than 60 days. Suddenly, I am now experiencing a couple of glitches. The first is that I get a certificate error when outlook tries it's first send/receive under the relevant profile - "The server you are connected to is using a security certificate that cannot be verified" This continues despite apparently successfully re-importing the certificate. The second glitch is that I get a "Sending reported error (0x8004010F): 'Outlook data file cannot be accessed'" error on send receive. Strangely, it seems to be trying to send/receive twice - once to 'mail@domain', which works, and the second to 'domain' which doesn't. I've tried deleting the profile and re-creating it, pointing to the original .pst file, but still get both errors. Does anybody know how I can resolve these errors? (As a by note, and not that important, more for curiosity, does anybody know why simply changing the delete from server setting against that profile would cause these issues?)

  Read the article

• Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

  - by sputnik

  I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

• CloneZilla Broke My System? Ubunut Installation Lost After Running CloneZilla

  - by nicorellius

  I just read through this post and tried to get my installation back using this answer to no avail. What happened to me is this: I spent an hour or more reading through the CloneZilla docs. I thought I was ready to test it out so I burned the disc with the ISO image on it and ran it. The system I used was Ubuntu 10.04, 32-bit. Everything seemed to go fine. I made a clone of my first partition and copied it to my second partition. I followed the instructions, removed the disc and rebooted my system. At this point, I would expect to have two bootable Linux installations, identical to one another. However, upon booting, I got this error message: error: no such device: 4cf1a6ef-xxxx-xxxx-xxxx-4e3a3ce92bcd error: file not found I booted from a Live Ubuntu disc and was able to see my to partitions: 4cf1(1) and 4cf1(2) (abbreviated, because the volumes have long numbers to identify them). The 50 GB partition, on which the original Ubuntu installation sits is the number and the second partition (175 GB) is the same number with an "_" at the end. I could browse the disc partitions and see the files, but I'm not sure what to do next. I know there is a way to restore my grub loader and actually boot either of these installations, but my Linux know-how is limited. Can I edit the boot loader file to fix this problem? The only clue I have is CloneZilla said something about making a new GRUB but I thought it was going to basically modify it so I could boot either installation. Not sure what happened. I am going to look through this post for the time being to see if I can learn anything to help my problem. But I thought that, since this happened as a result of using CloneZilla, it may be a unique question for this board.

  Read the article

• Motion - takes snapshot without motion detected

  - by Emmanuel Brunet

  I've been installed the standard motion 3.2.12 package on debian 7.5. I would like to get snapshot ONLY when motion is detected, but it still saves a picture every second without any activity in front of the camera. I'm using a TENVIS JPT3815W IP camera motion.conf here is my configuration file setup_mode off target_dir /media/videos/log/webcam netcam_url http://webcam/snapshot.cgi netcam_tolerant_check on netcam_userpass admin:alpha1237 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion off output_all off # detection settings 1-255 default 32 noise_level 50 # Maximum framerate for webcam streams (default: 1) webcam_maxrate 25 pre_capture 0 framerate 25 gap 30 locate on mail [email protected] text_right "FRONT CAMERA %Y/%m/%d - %T" text_double on ffmpeg_cap_new on ffmpeg_cap_motion on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) quality 90 # Restrict webcam connections to localhost only (default: on) webcam_localhost off # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 Issue when I start motion images are stored in /media/videos/log/webcam nearly every second. I hjust want to get images when a motion is detected and the according video clip Any idea where the configuration fails ?

  Read the article

• Fixed Resource Monitor Graph Scale in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums?

  Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >