Search Results

Search found 20264 results on 811 pages for 'home networking'.

Page 120/811 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127 | Next Page >

Ad-hoc connection between iPhone and Macbook Pro

- by Phil Nash

I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

Read the article
Dell Studio 15 Broadcom wireless drivers not working in Linux Mint

- by dcd0687

I installed Linux Mint 12 on my Dell Studio 15 and everything worked perfectly up until I tried updating the STA Driver for the Broadcom (BCM4312) wireless controller. I've tried these bash commands in order and I still don't have wireless. sudo apt-get install b43-fwcutter sudo apt-get install b43-fwcutter firmware-b43-installer I've also tried uninstalling everything with synaptic package manager including broadcom-sta-common and broadcom-sta-source, then restarting and running the above commands which didn't work either. What's the best way to do this on a Dell Studio 15?

Read the article
Why don't I have write permission to my vmware virtual network device?

- by Robert Martin

I want to allow my VMWare machine to force the virtual network it's on into promiscuous mode so I can play around with honeyd. I received an error message that told me to go to http://vmware.com/info?id=161 to allow this behavior. Based on their advice, I did: $ groupadd promiscuous $ cat /etc/group | grep promiscuous promiscuous:x:1002:robert $ usermod -a -G promiscuous robert $ id robert uid=1000(robert) gid=1000(robert) groups=1000(robert),....,1002(promiscuous) $ chgrp newgroup /dev/vmnet8 $ chmod g+rw /dev/vmnet8 $ ls -l /dev/vmnet8 crw-rw---- 1 root promiscuous 119, 8 2012-03-29 10:29 /dev/vmnet8 Looks like I gave RW permission to the promiscuous group, and added myself. Except that VMWare still gives me an error message that says I cannot enter promiscuous mode. To try out the group thing, I tried: $ echo "1" >/dev/vmnet8 bash: /dev/vmnet8: Permission denied That really surprised me: It makes me think that I still haven't properly given myself the correct permissions... What am I missing?

Read the article
How do I locate the app generating this network traffic?

- by Christopher Bartels

I don't know what this process is doing on my computer. I run Windows 7 Professional w/ all its updates running current non-free antivirus. I only see it in Resource Monitor, where you can see the Network Service process connected to bitum.nnov.ru. When my PC's network traffic generating apps are idle, this process is using the most of all the idle processes using the network. Screenshot hosted here: http://sss.proinbox.com/bitum-nnov-ru.jpg Does anyone recognize this? The page source mentions a control port & a stream port: Page Source for http://bitum.nnov.ru : <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <title>DVR WebViewer</title> <meta http-equiv="Content-Type" content="text/html; charset=euc-kr"> </head> <body topmargin="0" leftmargin="0"> <OBJECT classid="clsid:EE479A40-C128-40DD-93DA-000556AF9607" codebase="CtrWeb.cab#version=1,0,2,2" width=875 height=585 align=center hspace=0 vspace=0 > <param name="CmdPort" value="5920"> <param name="StreamPort" value="5921"> </body> </html> When I google this page's title, I see a number of other domains that host the same page. Whois: domain: NNOV.RU nserver: ns.kis.ru. nserver: ns.nnov.ru. 78.25.80.210 nserver: ns1.kis.ru. nserver: ns2.kis.ru. state: REGISTERED, DELEGATED, VERIFIED org: "Agentstvo Delovoj Svjazi", Ltd registrar: RU-CENTER-REG-RIPN admin-contact: https://www.nic.ru/whois created: 1996.10.23 paid-till: 2012.11.01 free-date: 2012.12.02 source: TCI Last updated on 2012.06.16 04:20:46 MSK

Read the article
Modify registry for Internet Connection Sharing?

- by Tim

My OS is Windows XP. Quoted from How to Change the IP Range for the Internet Connection Sharing DHCP service Use Registry Editor to modify the data value of the IntranetInfo value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Settings\General The first number listed is the IP address of the internal IP address of the Connection Sharing host. The second number is the subnet IP address separated by a comma. Enter the first IP address of the new range followed by the subnet mask, separated by a comma. (For example, 169.254.0.1,255.255.0.0.). Modify the data value of the Start value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Addressing\Settings Change the value to the second address of the selected IP range. This address cannot be the same or a lower value than the IP address used for the IntranetInfo key. Modify the data value for the Stop value in the same registry key. Enter the last the IP address of the selected IP range. My registry table does not have Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing, and I don't know how to do with my registry table following the above three steps. Can someone guide me through it step by step?

Read the article
Unable to access VLAN host from VLAN interface in CentOS

- by Amrit

I am playing with VLAN (Virtual LAN) configuration on CentOS 6.4. I have 2 interfaces, eth0 and eth1. I have configured 2 VLAN interfaces eth0.20 and eth0.30 as #file: ifcfg-eth0.20 #------------- VLAN=yes DEVICE=eth0.20 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.20.1 GATEWAY=192.168.20.1 NETMASK=255.255.255.0 USERCTL=no #file: ifcfg-eth0.30 #------------- VLAN=yes DEVICE=eth0.30 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.30.1 GATEWAY=192.168.30.1 NETMASK=255.255.255.0 USERCTL=no Then connected a desktop to interface eth0 port using LAN cable and assigned 192.168.30.2/24 IP. When I try to ping 192.168.30.1 from 192.168.30.2 machine, It shows destination host unreachable. I am also not able to ping 192.168.130.2 from 192.168.30.1. However ping -I eth0 192.168.30.2 works fine. Any pointers?

Read the article
OpenVPN DNS: VPN DNS stomping local VPN

- by Eddie Parker

I've finally noodled with OpenVPN enough to get it working. Even better, I can mount samba drives, ping network machines through the TUN device, etc - it's all great. However, I'm noticing that if I use the following directive, then some of the machines that are normally visible by the client, on the client's side (i.e., not through the VPN) get masked with some other server out on the Internet. push "dhcp-option DNS 10.0.1.1" # Push our local DNS to clients Is there any way to avoid this, besides hacking the 'hosts' file on the client machine? Ideally I'd like to only use my VPN's DNS for machines within that domain.

Read the article
Campus Network Design - Firewalls

- by user3081239

I am designing a campus network, and the design looks like this: LINX is The London Internet Exchange and JANET is Joint Academic Network. My goal is an almost-fully redundant with high availability, because it will have to support about 15k people, including academic staff, administrative staff and students. I have read some documents in the process , but I am still not sure about some aspects. I want to dedicate this one to firewalls: what are the driving factors in deciding to employ a dedicated firewall, instead of an embedded firewall in the border router? From what I can see, an embedded firewall has these advantages: Easier to maintain Better integration One less hop Less space requirement Cheaper Dedicated firewall has the advantage of being modular. Is there anything else? What am I missing?

Read the article
Enable SMB file sharing on OS X - "Incorrect Password"

- by Tim Robinson

I have a Mac running Snow Leopard connected to an Active Directory domain. I can share folders on the Mac and view files from Windows without problems. When I try to enable my Mac account for write access through System Preferences, I'm prompted for my account's password. Even though I'm entering the right one, I get an "Incorrect Password" response. The same process works fine for the local Mac administrator account; it's the Active Directory account I'm having problems with. I followed the advice on this page on apple.com without success: (I used the Mac to reset my domain password, and re-created my login keychain) If you want to use a user account that existed before you installed Mac OS X 10.3 (Panther), you may need to reset the password for the account using Accounts preferences. Can anyone suggest what might be wrong? Until I fix this I can't write to my Mac file share from Windows.

Read the article
Reaver keeps reapeating the same PIN

- by Umair Ayub

I have been trying to Hack a WPA2 Wifi and so far I am stuck with it. Problem is that it keeps trying same pin over and over again. Here is the last REAVER command I entered. reaver -i mon0 -b 2C:AB:25:51:F1:CF -vv -c 1 -S -L -f It does this (only one PIN again and again) [+] Switching mon0 to channel 1 [+] Waiting for beacon from 2C:AB:25:51:F1:CF [+] Associated with 2C:AB:25:51:F1:CF (ESSID: PTCL-BB) [+] Trying pin 12345670 [+] Sending EAPOL START request [+] Received identity request [+] Sending identity response [!] WARNING: Receive timeout occurred [+] Sending WSC NACK [!] WPS transaction failed (code: 0x02), re-trying last pin [+] Trying pin 12345670 [+] Sending EAPOL START request [+] Received identity request [+] Sending identity response [+] Received identity request [+] Sending identity response ^C [+] Nothing done, nothing to save.

Read the article
Migrating from DD-WRT to Tomato

- by Collin Allen

Is it possible to switch to the latest version of Tomato on a router that's already running DD-WRT? Using the default Linksys firmware on my WRT54GL v1.1, I had to upload a micro version of DD-WRT first. I imagine that, since I'm now running third-party firmware, I won't have to do that again to make the switch, but I thought I should check so as not to brick it. This router is taking a back seat to a new AirPort Extreme (for the 'n' capability), but I still want to have the soon-to-be-Tomato device sit between the AirPort Extreme and my modem for the superior traffic graphing.

Read the article
network design to segregate public and staff

- by barb

My current setup has: a pfsense firewall with 4 NICs and potential for a 5th 1 48 port 3com switch, 1 24 port HP switch, willing to purchase more subnet 1) edge (Windows Server 2003 for vpn through routing and remote access) and subnet 2) LAN with one WS2003 domain controller/dns/wins etc., one WS2008 file server, one WS2003 running Vipre anti-virus and Time Limit Manager which controls client computer use, and about 50 pcs I am looking for a network design for separating clients and staff. I could do two totally isolated subnets, but I'm wondering if there is anything in between so that staff and clients could share some resources such as printers and anti-virus servers, staff could access client resources, but not vice versa. I guess what I'm asking is can you configure subnets and/or vlans like this: 1)edge for vpn 2)services available to all other internal networks 3)staff which can access services and clients 4)clients which can access services but not staff By access/non-access, I mean stronger separation than domain usernames and passwords.

Read the article
How to hack airport extreme to support USB 3G modem?

- by Mike Caron

Has anyone out there ever tried to hack the Airport Extreme, specifically with regard to the USB port? There are many cellular routers available that provide WiFi sharing of a USB modem link. However, instead of buying yet another router, I'd like to use my expensive Airport Extreme with it. The AE has a USB port on the back, but it's been said that it only talks to printers. Is there a way to hack the USB driver on the AE to allow it to recognize a USB modem, then use that as the connectivity instead of the LAN? I would imagine that one could use OpenFirmware to boot something on the AE. If one can boot it, then one could provide access using SSH across the lan. Once access is granted, then let the hacking begin... but I don't know how to (a) get the mini-osx on to USB (is it the same as the ATV without a UI?) or (b) how to load up certain things once boot has begun.

Read the article
What's wrong with my custom patch cables?

- by stu42j

I have a box of bulk Cat5e riser cable left over from when I had my house wired. I figured I could use this to make some custom length cables for connecting my computers, switches, etc. I had a crimper already so I bought a bag of RJ45 plugs. I made a few cables several years ago, but my experience/knowledge with this sort of thing is minimal. None of my cables are working. I don't have a tester so I just plug the cable into a computer and switch but I get no link light. I wired them them all straight-through and visual inspection doesn't show any problems. Any ideas what I might be doing wrong?

Read the article
How do I configure an interface to have *both* a DHCP address and a static address in Ubuntu?

- by Paul Hoffman

In a lab setup, I want eth0 on a Ubuntu server box to get a DHCP address for talking to the outside world, and I also want to assign it a static 10.x.y.z address for talking to other boxes on the local network that have 10.x.y.z addresses. I want to do this by editing /etc/network/interfaces. The man page for /etc/network/interfaces is modeled after "here's a bunch of examples, I hope you can figure out the actual rules on your own". I don't see a way to give one interface two addresses using two different methods (static and dhcp), and initial fumbling didn't produce useful results.

Read the article
Configure BL-C111A IP Camera

- by csmba

I am an ATT DSL customer. I want the camera to send an email when motion detection is triggered. Can anyone tell me how he managed to do that using: GMail (I cannot because I don't think it supports SSL) other alternatives if GMail is not supported

Read the article
How to permanently add wireless interfaces with iw

- by walli

How can I permanently add virtual wireless interfaces to my network configuration with iw? I created the following interfaces: iw phy phy0 interface add vwlan0 type station iw phy phy0 interface add vwlan1 type __ap The first is configured as a wifi client connecting to an existing network (wpa_supplicant) The second is configured as wireless hotspot (hostapd + dnsmasq) The setup works, but now I can't quite figure out what the best strategy is to save this configuration permanently. Have made an init script for wpa_supplicant Have made an init script for the hotspot Virtual adaptor network settings set in /etc/network/interfaces But all this depends on the wireless interfaces being created. What would be the best way to make sure these interfaces are created before the network is set up and the services are run? As a bonus, since this wireless interface is a usb device, would it be possible to have the interfaces created (and the services started) when the interface is hotplugged? I know you can execute code after a network interface is up, but the wlan0 interface that is hotplugged should never be up. Operating system is raspbian

Read the article
iPod touch has extremely slow wifi, drops packets - only on my router

- by mskfisher

I just purchased an iPod Touch. I am having a lot of trouble with its speeds on my Tenda W311R, but it has no speed problems on my neighbor's Netgear router. It will connect and authenticate to my network, but the Speed Test app from speedtest.net shows rates near 20-50 kbps. If I run the speed test immediately after powering the iPod on, it will get speeds of 10-20 Mbps, like it should - but the speeds slow down to the kbps range abut 10-15 seconds afterward. I get the same behavior with encryption and without encryption, and regardless of N, G, or B compatibility settings in the router. I've tried rebooting the iPod and resetting the network settings, but it's still slow. I've tried pinging the iPod from another computer, and it shows about 40% packet loss: $ ping 192.168.0.111 PING 192.168.0.111 (192.168.0.111): 56 data bytes 64 bytes from 192.168.0.111: icmp_seq=0 ttl=64 time=14.188 ms 64 bytes from 192.168.0.111: icmp_seq=1 ttl=64 time=11.556 ms 64 bytes from 192.168.0.111: icmp_seq=2 ttl=64 time=5.675 ms 64 bytes from 192.168.0.111: icmp_seq=3 ttl=64 time=5.721 ms Request timeout for icmp_seq 4 64 bytes from 192.168.0.111: icmp_seq=5 ttl=64 time=6.491 ms Request timeout for icmp_seq 6 64 bytes from 192.168.0.111: icmp_seq=7 ttl=64 time=8.065 ms Request timeout for icmp_seq 8 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 64 bytes from 192.168.0.111: icmp_seq=11 ttl=64 time=9.605 ms Signal strength is good - I'm never more than 20 feet from my access point, and it exhibits the same behavior if I'm standing next to the router. It works just well enough to receive text, but videos don't work at all. App downloads are hit and miss. I've tweaked just about all of the settings I can see to tweak, and I'm at a loss. I have also been searching Google for the past three days, all to no avail. Any suggestions?

Read the article
Sonicwall routing between multiple subnets on multiple interfaces

- by Rain

As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

Read the article
Wireless Network Issue, Disconnecting Randomly From Network

- by Surfer513

I'm having an odd problem with my wireless network. Here is the background information: Server (Windows Server 2008) 1 to 10 end user machines connecting to the network Layer 3 Access Point (Asus WL-330 gE) connected to ethernet of Server and all machines connect to the network via the AP The end user machines get a connection to the server with no problems initially. But then connections are randomly lost throughout the day to the server/network. The wireless NICs of the machines still see the wireless network but are unable to connect to it. Then after some time the connection is regained automatically. I initially thought there was a problem with this particular AP, but then I took the same make/model AP out of storage and still ran into the problem. Any ideas what could be causing this??? Very confusing that the wireless nics on the end user machines can still see the network but not connect, and that the connections are randomly lost/gained. Thanks in advance!

Read the article
Request time out error

- by Neo

Hi Today i came across strange problem whenever i try to pinging to my server works properly but whenever i send http request from browser the request time out happens. can anybody help me to resolve this issue.

Read the article
Trouble connecting a Ubuntu system to IPv6 tunnel over NAT

- by John Millikin

I'm trying to set up an IPv6 tunnel, via Hurricane Electric's tunnel-broker service. I've configured my system using their example commands: # $ipv4a = tunnel server's IPv4 IP # $ipv4b = user's IPv4 IP # $ipv6a = tunnel server's side of point-to-point /64 allocation # $ipv6b = user's side of point-to-point /64 allocation ip tunnel add he-ipv6 mode sit remote $ipv4a local $ipv4b ttl 255 ip link set he-ipv6 up ip addr add $ipv6b dev he-ipv6 ip route add ::/0 dev he-ipv6 And have configured my desktop to be in my NAT router's DMZ. The router is running Tomato firmware. But I can't ping any IPv6 services: $ ping6 -I he-ipv6 '2001:470:1f04:454::1' PING 2001:470:1f04:454::1(2001:470:1f04:454::1) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes From 2001:470:1f04:454::2 icmp_seq=1 Destination unreachable: Address unreachable From 2001:470:1f04:454::2 icmp_seq=2 Destination unreachable: Address unreachable I can ping my local address: $ ping6 -I he-ipv6 '2001:470:1f04:454::2' PING 2001:470:1f04:454::2(2001:470:1f04:454::2) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes 64 bytes from 2001:470:1f04:454::2: icmp_seq=1 ttl=64 time=0.037 ms 64 bytes from 2001:470:1f04:454::2: icmp_seq=2 ttl=64 time=0.039 ms I don't know much about routing, but results I found online suggested the output of ip -6 route and ip addr could be useful: $ ip -6 route 2001:470:1f04:454::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev virbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 default dev he-ipv6 metric 1024 mtu 1480 advmss 1420 hoplimit 4294967295 $ ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:1c:c0:a1:98:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.1.10/24 brd 192.168.1.255 scope global eth1 inet6 fe80::21c:c0ff:fea1:98b2/64 scope link valid_lft forever preferred_lft forever 3: virbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 36:4c:33:ab:0d:c6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 inet6 fe80::344c:33ff:feab:dc6/64 scope link valid_lft forever preferred_lft forever 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:76:62:6e:65:74 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 7e:29:5e:7c:ba:93 brd ff:ff:ff:ff:ff:ff 6: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 7: he-ipv6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN link/sit 24.130.225.239 peer 72.52.104.74 inet6 2001:470:1f04:454::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::1882:e1ef/128 scope link valid_lft forever preferred_lft forever

Read the article
How to install Archlinux on a acer emachines em350 ?

- by zillion

Do a 64 bits version will work better if the cpu is 64 bits capable ? Can I remove all added stuffs on Archbang or CTKArchLive to return to plain Archlinux with openbox that I can configure myself easily, so I can install Archlinux faster ? I tried and installed Arch properly but I need to install the broadcom bcm 4727 driver (b43,wl,sta,open source), which driver do I need and how can I install it by my usb on Archlinux CLI made with base, sudo and wireless_tools only ?

Read the article
VMware Fusion configuration files missing

- by jdmuys

I need to set up port forwarding to my VM in Fusion 5. Everywhere on the net, the solution is described as editing the file: /Library/Application Support/VMware Fusion/vmnet8/nat.conf However, on my install, that file doesn't exist. Neither does the vmnet8 directory. Here is the full content of VMware stuff I have in /Library/Application Support/: /Library/Application Support/ VMware/ VMware Fusion AdminWritable Shared vmInventory usbarb.rules VMware Fusion That's right: /Library/Application Support/VMware Fusion/ exists but is empty. And there is no VMware folder in other Library directories on my system. I am running OS X 10.8.2. I just reinstalled Fusion 5.02, no change. Meanwhile, I have 3 VMs that work just fine. So how am I supposed to set up port forwarding with Fusion 5? Thanks, JD Edit: in a hunch, I tried ps ax | grep natd which returned: 9646 ?? S 0:00.01 /Applications/VMware Fusion.app/Contents/Library/vmnet-natd -s 7 -m /Library/Preferences/VMware Fusion/vmnet8/nat.mac -c /Library/Preferences/VMware Fusion/vmnet8/nat.conf So it seems that the configurations files are now in the directory /Library/Preferences/VMware Fusion. I'll work from here and edit this question as I make progress.

Read the article
Setup LAN to serve webpages and voip and access to the web site from inside LAN with domain name

- by Mauricio Arias

I'd like to know if it will work: I have my domain and I´m serving a webpage in a nginx to the internet, but if I type my domain in my laptop inside LAN I access to my modem/router configuration, I cannot access to the web server unless I type the IP address. I would like to add a Bind server after the modem/router - (port forward, ports 80 and 5060), if the request is www.mydomain.com bind should resolve the nginx IP address and serve it, and if it is a voip request should address to the voip server and if I'd like to access to the website from inside LAN I'd like to type mydomain.com. Could I do it with this configuration? Do I need something else? Thanks in advace!

Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127 | Next Page >