Search Results

Search found 4144 results on 166 pages for 'macbook recovery'.

Page 120/166 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >

  • Windows 8.1 Update 1 Disk Usage 100%

    - by Gookjin Jeong
    Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

    Read the article

  • Why has my Mac been running fsck_hfs for two days now?

    - by Nate
    I first noticed that fsck_hfs was running, taking up 50-75% of a CPU, yesterday. It continues to run today. ps shows that it is doing /sbin/fsck_hfs -f -n -x -E /dev/disk3. Only problem: I don’t think I have a /dev/disk3. Why is it running? Will it ever finish? Can I kill it? What is /dev/disk3? Could it be my Time Machine volume, which is not mounted at the moment? System Info: MacBook Pro (2008). It has two disks installed—the internal disk (/dev/disk1) and a PC Card SSD (/dev/disk0, surprisingly). It connects to a remote Time Machine volume attached to an Airport Extreme base station.

    Read the article

  • HFS partition mounting read-only

    - by Sid
    Hey, I have an external Western Digital Hard drive with two HFS partitions with journaling disabled. When I connect it to a computer running Linux (Debian or Ubuntu), frequently both partitions are mounted read-only. In the past, mounting them on my Macbook and executing the command to disable the journaling often worked (even though it would tell me that journaling was already disabled) but I would love to have a solution which works every time. Thanks! Edit: In light of Chris Johnsen's comment below - my question is how to mount the filesystem read+write on Linux since it is not automatically doing so itself

    Read the article

  • Mac failing (failed?) hard drive - is all hope lost?

    - by Daniel
    It's a 500 GB Seagate laptop hard drive that came with my Macbook Pro. Apple partition format. Already replaced and now have it external, connected via SATA/USB adapter. Trying to get just a few files that I worked on while out of town when it crashed (and thus did not have my time machine backup drive). Drive will not mount, but OS X Disk Utility detects it and can read the capacity, model number, and even the name of the partition, which leads me to believe all hope may not be lost. Failed attempts so far: Disk Utility verify+repair says drive cannot be repaired and that I should back up immediately (lovely) Disk Warrior says it cannot rebuild the directory due to hardware failure Data Rescue quick & deep scans immediately failed PhotoRec says "error reading sector" for every sector (at least for the few minutes I let it run before closing it to explore other options) What else can I try here? Again, I'm just looking for a few, small files (python scripts to be specific) - not a full recovery.

    Read the article

  • Burn iTunes playlist to Audio Image

    - by MikeHoss
    I have Snow Leopard on an early model MacBook Pro. The CD Drive has been giving me fits the last few months -- I stick a blank CD in it, and it claims it's bad and spits it out. I can go through a pile of brand-new CD's and it will choose 1 out of 7 that it wants to use, even though all the CD's come from the same package. The rejected CD's work fine on a Linux machine I have. I need to burn an audio CD from iTunes and my thought was: Burn playlist to audio CD Image file (Red Book image?) Copy ISO file to Linux Machine Use Linux machine to burn audio image to a CD But looking around, it doesn't seem that iTunes on OSX will support this. I was wondering if anyone else has accomplished this.

    Read the article

  • Disable OS X Portable Home Directories for specific hosts for all users, not just individuals?

    - by Paul Nendick
    Would it be possible to block any and all Portable Home Directory services for specific hosts? Something like MCX's "MobileAccountNeverAsk-" but for the whole workstation? We have a network with both portable and stationary machines. I'd like our users to be able to use all machines, going portable on the MacBook but not being bothering with syncing when logged into stationary iMacs or Mac Pros. The Open Directory servers are running Snow Leopard (for now) and all clients are running Lion. Thanks! Paul

    Read the article

  • Installer hangs on "waiting for other installations to finish" despite no other installations in progress

    - by clozach
    I started an installation of the Xcode 4 developer's preview last night before going to bed. When I woke up, the installation had popped up a message saying to close Xcode first (doh!). I did so, but whatever script had displayed the message seemed to have hung because the (uncancellable) message wouldn't disappear, and the installer wouldn't progress. After force quitting the Installer app, the message above was still showing, so I restarted my MacBook Pro and then tried the installation again. This time it wouldn't even start, instead showing one of those candy-stripe activity bars and the message: Waiting for other installations to finish At this point, I'm stumped. There are no other installations in progress, so there must be some artifact left over from the interrupted install that's gumming up the works. But what?

    Read the article

  • Why does my iTunes use so much CPU time?

    - by bikesandcode
    I have a roughly 2 year old Macbook (10.5). I have iTunes 10. When iTunes is playing MP3s, I see CPU usage of the iTunes process in the system monitor ranging from 65%-75%. When I pause the music, I see CPU usage of about 65%-75%. I do not have any visualisations going, to my knowledge I have not turned on any CPU destroying features, my music library isn't tiny, but it's hardly huge (3GB). This is mildly annoying when I'm plugged into the wall as I only have slightly longer compile times, but if I am out and about, this is a major drain on the battery. Using VLC I see CPU loads of ~= 10% at the most when listening to music and generally lower. What the heck is iTunes doing?

    Read the article

  • Deleting slow on X11 emacs

    - by Malvolio
    I'm running GNU Emacs 21.4.1 on a (remote) remote Linux ((CentOS) box, using my MacBook as the X-server. Works fine, unless I try to delete a word, line, or region. Then it locks up for 30 seconds or so. It sounds like a minor thing, but you realize how often you do a delete when you have to stop for 30 seconds every time. My theory is that Emacs is trying to put the text in the X-server cut-and-paste buffer, which is trying to put it in the OSX cut-and-paste buffer and somewhere along the way, the process is blocked until it times out. (My only evidence for this theory is (a) copy-region behaves the same way and (b) deleted text doesn't show up in the buffer.) Any suggestions appreciated. Edit: (setq interprogram-cut-function nil) fixed me right up. Which makes perfect sense. Thanks, Trey.

    Read the article

  • Thunderbird 3.0 refuses to start on Mac OS X?

    - by jtimberman
    I just downloaded Thunderbird 3.0 on my Macbook Pro running Leopard, and installed it in /Applications. When I attempt to start it, the icon opens on the Dock as normal, but I get the following dialog. I don't have a ~/Library/Application Support/Thunderbird directory at all, let alone a .parentlock file. While I didn't expect it to help, I did reboot my system. And sign out and back in. And close all programs besides Thunderbird. Earlier versions of Thunderbird have worked just fine.

    Read the article

  • Bold font shortcut in WordPress editor in Mac OS X? (The equivalent to Ctrl+b in Windows)

    - by javipas
    I've recently acquired a MacBook Air and I'm getting used to Mac OS X shortcuts. One that I can't find, though, is the change to bold a piece of text previously selected in the WordPress editor. I do this with a simple Ctrl+b after selecting the text in Windows, but the expected Command+b in Mac OS X does not work (in WordPress at least. It seems it works in other editors online and offline). Is there a shortcut for it... and for italics?

    Read the article

  • WD Passport Won't Mount

    - by Scott7278
    My WD Passport won't mount. However, it turns on when plugged into my macbook and doesn't make any strange noises. It took a small fall (just a few inches and it was on my couch) and I'm very concerned about physical damage. When I open up disk utility it shows the root 500 GB WD My Passport drive which seems to be OK when I verify it and repair it. However, the "External Hard Drive", the directory underneath the "500 GB WD My Passport drive" is grayed out. When I verify the External Hard Drive it says it needs to be rapaired. When I try and repair it it gives me the following message and does not seem to progress: "Updating boot support partitions for the volume as required." Is there hope for me recovering my data? I stupidly have important data on it that I don't have anywhere else.

    Read the article

  • Slow internet connection on Mac OS

    - by user984621
    At home, we have a router. From router goes the internet connection into the desktop PC (Windows 7) and Macbook Pro. The problem is, that on Mac OS is incredibly slow internet connection - is not possible to use the laptop for surfing on the internet. The same as for WiFi as for cable. On the PC with Windows 7 is working the internet connection properly. Is there any tool for testing, if on my Mac is a virus or just something, what slowing down the internet connection? THank you in advance.

    Read the article

  • Catch headset pause/play keypresses in Windows

    - by akshay2000
    I have a new Ultrabook which has single audio jack for input and output instead for separate 3.5 mm jacks we used to have on older machines. The jack is probably similar to American Audio Jack specification or like the one found on Macbook Pro. I have tried to use it with the Apple, HTC, Nokia earphones which ship with most of the smartphones. Microphone on the headset works the way it should. Thing is that the headsets also come with remote controls to control volume and playback. I am sure that those key presses are sent to the Windows. I was hoping to catch those events and bind those to actual media keys so that I can control music playback. I guess this happens on Macs. I want to do the similar thing on the Windows. I'm just not sure where I can catch the events. Driver level? Application level?

    Read the article

  • How to configure Time Machine to also backup an connected external hard drive?

    - by Another Registered User
    I've inserted a sweet SSD into my MacBook Pro, but it had limited space. So I had to export 60 GB of Data to an external hard drive. But now, when I run TimeMachine to backup my stuff, of course it only backups what's on the system disk. Is there a way how to also backup the connected external hard drive together with TimeMachine? Maybe there's a trick to get this work, with a fake folder that's actually the mounted drive? What could I do?

    Read the article

  • Windows 7 installer doesn't recognize NTFS partition.

    - by ifesdjeen
    Hi, I'm trying to install windows 7 on my Macbook. I've created NTFS partition, but when i'm starting up Windows 7 installation, it says that i can't install windows on this partition, since drive already contains maximum amount of partitions with this filesystem type. I haven't heard of any limits on filesystems, but still i can't even format this drive from Win7 installer. I've found access to command line from win7 installation CD, but i can't find fdisk there to format. Do you have any idea on about how to deal with it?

    Read the article

  • Access Linux Samba-Share from Snow Leopard

    - by Space_C0wb0y
    Hello there! I have a linux machine with a samba-share. Other windows machines can access that samba-share no problem. Now I have a new MacBook running Snow Leopard and I have no clue on how to access it. In finder it shows the linux-machine, but I have no idea how to access it. In some blog it said that this: `smbclient -U <username> -L <hostname>` can be used to list samba-shares. When I do it, I get `session setup failed: NT_STATUS_LOGON_FAILURE` I am at a loss here. Any help on how to approach that problem would be appreciated. Can you provide some hints or point me to some good howto?

    Read the article

  • How to open a TrueCrypt volume quickly on a Mac?

    - by ssc
    Whenever I need to access data stored in the TrueCrypt-protected volume on my MacBook, I need to start TrueCrypt from the Dock, select the volume file, click mount, enter the password and then open a Finder window and browse to the volume. I want a quicker way, e.g. double-click something on the desktop (and/or press a hotkey combination), enter the password and have a Finder window pop up. I have done an extensive research on the TrueCrypt website, Apple Automator and some other approaches, but nothing really seems come up. Has anyone realized the approach described ?

    Read the article

  • How do I transfer .pst e-mails from Outlook to a Mac e-mail program?

    - by user46248
    New Macbook Pro came in yesterday with MS Office Outlook crashes consistently on importing from .pst after about 30 seconds. I see a EXC_BAD_ACCESS and something about CF get string length or the like. Tried 2 different .pst files created on different dates of different folders. Mail and Thunderbird lack options for importing from .PST. I can export to .csv but still didn't see an option for importing that. How can I get my .pst files into an e-mail client on the Mac?

    Read the article

  • Do TCP connections work differently within the same subnet?

    - by Dean
    I've encountered some network behaviour that confuses me while trying to get Java RMI working. I use netcat to connect to a local machine: [my_machine]$ nc -w 1 192.168.0.100 60000 && echo success success I try to do the same to my server: [my_machine]$ nc -w 1 my-servers-ip 60000 && echo success This doesn't work, unless I explicitly listen on the server socket: [amazon_ec2]$ nc -l 60000 [my_machine]$ nc -w 1 my-servers-ip 60000 && echo success success For the version that fails, the SYN packet receives a RST, ACK in response. I'm not too knowledgable about this stuff, at this point I only have wild theories such as the one in the question. Any ideas? Potentially useful details: Local Machine (192.168.0.100) - Macbook Remote Machine (Amazon EC2) - Amazon Linux AMI 2012.03 Security Group Settings: 22 (SSH) 0.0.0.0/0 1099 0.0.0.0/0 49152-65535 0.0.0.0/0 "iptables -L" shows no rules set

    Read the article

  • Terminal runs svn commands very slowly, how can I speed this up?

    - by Paul
    Spending all day in terminal is beginning to get frustrating. We're working with large CakePHP projects, including a ton of schema files and complex controllers. Whenever I go into a project, and enter svn up, or svn ci my system chokes. It takes a good 15-30 seconds before it returns what revision number I'm on. I'm running OSX 10.6 on a Macbook Pro. Any reasoning behind this? Anyway I could fix this speed issue?

    Read the article

  • Open original Microsoft Office document (not "version 1") on Mac OS X Lion restart

    - by FlyingMolga
    My MacBook Pro running Lion has been frequently freezing lately, and I've had to restart with the power button. When Lion starts up again, the Microsoft Office applications that were running start and load different autosaved versions of the documents I had open (i.e. it does not open abc.xlsx but [version 1] of abc.xlsx). Sometimes it also opens the original files. Several times I've inputted data into these "version 1" files, only to try to save it and realize that it isn't the original file and is sometimes missing data that is contained in the original file. Is there any way to make autorecover open the actual document with the unsaved changes, instead of making a new temporary version?

    Read the article

  • Do I need a driver to use use Samsung P2770H Monitors with OSX?

    - by anagi
    I am would like to buy this Samsung monitors to be used with my macbook pro. However, when I went to the website of the Samsung, I couldn't find any driver for osx. I also read on some forum, that apple doesn't work WELL with most 3rd party monitors, because apple is trying to get people to buy their expensive monitors. While this might be an incentive, I thought the decision to manufacture a driver was up to Samsung and not apple. But then since I don't know much about this subject, I thought of getting the online expert opinion. So to be be more precise: Does anyone if this particular monitor works with OS X?

    Read the article

  • How can one create a bootable linux usb key that works on Mac (Intel 64 bit CPU) hardware ?

    - by user3621
    Hi, I'm trying to create a bootable usb key with linux (debian) and that can be booted on Macintel hardware. I have read that MAC's EFI can only boot GPT GUID formatted disks. I'm desperately trying to find a good tutorial which explains how to create such a key. Here what I have done so far: create a GUID partition on te key using linux GNU parted create a HFS+ or ext3 partition on the key, with the boot flag on install a linux .iso with unetbootin While all steps were successfull and in some cases I could even boot on a PC, the step of booting on Macintel software failed (on a macbook). I need to precise that I holded the "alt" key while booting the mac and the only visible bootable disk was the hard disk. Thanks for any advice. PS: I have tried with rEFIt as well. In one case I had a "windows" icon but it then failed to boot with a message like "no system found"

    Read the article

  • Win XP cannot connect (or see) my wifi network, but can see others

    - by Jorre
    since yesterday I have a strange wifi problem with my pc. I have a wireless linksys router setup that worked fine for many months, now since yesterday my pc won't connect to the wifi signal anymore. The strange thing is, my macbook pro still connects fine. SSID is broadcasting, but my windows XP doens't see it, I have all signal modes set to "auto". Windows XP sees all my neighbours wifi networks, so the wifi card isn't broken or anything. Any idea what can be wrong here?

    Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >