Search Results

Search found 38783 results on 1552 pages for 'graphical screen issue'.

Page 122/1552 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• webmin bind issue- error when i try to start bind

  - by Arvind

  I am setting up a domain = mydomain.com with 2 nameservers ns1.mydomain.com and ns2.mydomain.com in Webmin - BIND. For this, I have registered 2 child nameservers at my domain registrar, and in Webmin-Bind I have set up a new zone for this domain. In this zone, i have specified 2 nameserver records- one each for ns1 and ns2. Also, I have defined 2 address records- one each for ns1.mydomain.com -> IP Address #1 and for ns2.mydomain.com -> IP Address #2 However when I try to start BIND in Webmin, I get the following error-- Failed to start BIND : Starting named: Error in named configuration: zone mydomain.com/IN: has no NS records zone mydomain.com/IN: not loaded due to errors. _default/mydomain.com/IN: bad zone [FAILED]

  Read the article

• Cannot Delete Item "Could Not Find This Item" issue

  - by aronchick

  A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

  Read the article

• DNS updating issue

  - by Will

  Hey guys, I'm new to serverfault so please excuse me if I sound a tad nub. I work in an environment that is kinda peace mealed together, and I honestly don't know how it works. I'm new to the IT field and am still in school. When I replace a PC I rename the old one to mo-o-pcname and give the new one the proper name of mo-pcname (mo is a location thing we use so it really doesn't apply to the problem.) The new PC will function on the network; it will have the ability to access network resources (printers, file shares, etc) and it will have the ability to get out to the internet. However I can no longer ping the machine. It would appear as if the DNS (A) record is not getting updated or something. Like I said I'm kinda new to the field and just trying to work through this problem. Thanks for your help.

  Read the article

• Issue with InnoDB engine while enabling and [ skip-innodb ] - [ERROR] Plugin 'InnoDB' init function returned error

  - by Ahn

  How to enable InnoDB, which was previously disabled with skip-innodb option. Case 1: Disabled the innodb with skip-innodb option and show engines givens as below. Engine | Support ... | InnoDB | NO ...... Case 2: As I want to enable the innodb, I commanded the #skip-innodb option and restarted. But now the show engines even not showing the InnoDB engine in the list. ? Mysql Version : 5.1.57-community-log OS : CentOS release 5.7 (Final) Log: 120622 13:06:36 InnoDB: Initializing buffer pool, size = 8.0M 120622 13:06:36 InnoDB: Completed initialization of buffer pool InnoDB: No valid checkpoint found. InnoDB: If this error appears when you are creating an InnoDB database, InnoDB: the problem may be that during an earlier attempt you managed InnoDB: to create the InnoDB data files, but log file creation failed. InnoDB: If that is the case, please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/error-creating-innodb.html 120622 13:06:36 [ERROR] Plugin 'InnoDB' init function returned error. 120622 13:06:36 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 120622 13:06:36 [Note] Event Scheduler: Loaded 0 events 120622 13:06:36 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.57-community-log' socket: '/data/mysqlsnd/mysql.sock1' port: 3307 MySQL Community Server (GPL)

  Read the article

• Performance issue when configuring non HA VM in cluster

  - by laiys

  Hi, I saw this article http://technet.microsoft.com/en-us/library/cc764243.aspx Quote taken from the link “ Important It is recommended that you not deploy virtual machines that are not highly available on your host clusters. Although you can do this by using Hyper-V (VMM does not allow it), the non-highly available virtual machines will consume resources that otherwise would be available to the HAVMs What kind of resources (CPU,memory, NIC, etc) that non HA VM will consume? Just curious as not all VM (in production) not to be in Failover Cluster and Live Migration. If i put the VM into CSV but did not make it as HA, what impact does it make since i allocate same vCPU, vNic and VMemory into the VM. (not to mention that i lost failover feature). Curious to understand more about this. Please advise. Thanks

  Read the article

• Windows Server 2008 R2 Software Deployment on Active Directory - Schema Issue

  - by weedave

  We have two servers, one running Windows Server 2003 SP2 and one running Windows Server 2008 R2. Both servers have their own versions of Group Policy Management (1.0.2 on 2003 and 6.0.0.1 on 2008). We are wanting to migrate everything over to the newer 2008 server, including software deployment. However, when I try to add a new software package using a .msi file, I get the following error: "The schema for the software installation data in the Active Directory does not match the required schema." I have tried two separate software packages and get the same error on the 2008 server. However, when I do the same on the 2003 server, it adds the software package without any problems. The .msi files I am using are up-to-date - one is the most recent version of Google Chrome. Is this problem caused by the different versions of the OS, or the Group Policy Management program? How do we "upgrade" our Active Directory to allow software deployment on the 2008 server? Thanks.

  Read the article

• MS SQL to MySQL using MySQL Migration Toolkit: permission issue

  - by Zeno

  I have a MS SQL imported into SQL Server 2008 from a .bak and I set it to Mixed mode. I have a SQL user (called "test") that can correctly access the database using SQL Server. I need to convert this to a MySQL database, so I got the MySQL Migration Toolkit. I pick "MS SQL Server" and then it asks for the hostname/username/password/database. I'm not 100% sure on these, but I used "localhost" (running on same computer), left the port as is (1433) and the username/password ("test") for the SQL Server. And I used the database name for the SQL Server database I'm looking to import. I clicked next, enter my MySQL database details and then attempt to run it and I get this error: Connecting to source database and retrieve schemata names. Initializing JDBC driver ... Driver class MS SQL JDBC Driver Opening connection ... Connection jdbc:jtds:sqlserver://localhost:1433/Orders;user=test;password=blah;charset=utf-8;domain= The list of schema names could not be retrieved (error: 0). ReverseEngineeringMssql.getSchemata :Network error IOException: Connection refused: connect Details: net.sourceforge.jtds.jdbc.ConnectionJDBC2.<init>(ConnectionJDBC2.java:372) net.sourceforge.jtds.jdbc.ConnectionJDBC3.<init>(ConnectionJDBC3.java:50) net.sourceforge.jtds.jdbc.Driver.connect(Driver.java:178) java.sql.DriverManager.getConnection(Unknown Source) java.sql.DriverManager.getConnection(Unknown Source) com.mysql.grt.modules.ReverseEngineeringGeneric.establishConnection(ReverseEngineeringGeneric.java:141) com.mysql.grt.modules.ReverseEngineeringMssql.getSchemata(ReverseEngineeringMssql.java:99) sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) java.lang.reflect.Method.invoke(Unknown Source) com.mysql.grt.Grt.callModuleFunction(Unknown Source)

  Read the article

• Blue Screen Of Death after Graphics Card Update

  - by John Smith

  I recently installed the game watch dogs After installing it i upgraded the drivers on my graphics card AMD Radion R9 200 series via the catalyst software and since then windows has been crashing on an ad-hoc basis even when sitting idle I have recieved two different sets of errors OXOOOOOOO1 and VIDEO_SCHEDULER_INTERNAL_ERROR I am running windows 8.1 with the driver 14.4 from AMD My PC shouldnt really be having this problem as it is pretty high spec due to my work Any help would be greatly appreciated as it is driving me up the walls a bit [UPDATE 08-06-2014] I have been looking around online and have crashed the PC a few times now trying to recreate the bug I have looked into the event history viewer and gotten the following errors amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED acpusrsvc: GfxMemServiceInitialize: FAILED amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED amdacpusrsvc acpusrsvc: GfxMemServiceInitialize: FAILED I took some advice from the AMD forums to re-install the old drivers to see if they would work. I uninstalled the old ones first and installed directly from the CD I got the warnings below but the driver installed "successfully" The Warnings are amdacpusrsvc acpusrsvc: ConfigureFrameBufferMemory: FAILED. Hopefully this will spark something off for someone Thanks John

  Read the article

• excel 2010 format and input issue

  - by Craig Gunn

  I have completed a very complex Excel spreadsheet with a lot of equations, except ... I forgot to include September I have Jan through Dec, all the months, except the calculations for September. Of course all the equations are currently perfect for the data that's here. How do I add a whole new column without ruining the previous equations? PS: tomorrow is my holidays and I have to go to work to finish this table, so bad. would really appreciate some kind expertise :) cheers craig.

  Read the article

• ReadyNAS issue with Google Apps?

  - by Jauder Ho

  The power went out (again) in my house today so I decided to set up some alerting. Since I have a ReadyNAS and the latest version of Raidinator seems to have SMTP TLS support, I figured I would try setting things up to email to a domain I have hosted on Google Apps. At this point, I have everything working IF I use a Gmail account but as soon as I switch to a Google Apps email address, it stops working and complains with smtpstatus=535 smtpmsg='535-5.7.1 Username and Password not accepted. Learn more at \n535 5.7.1 http://mail.google.com/support/bin/answer.py?answer=14257 30sm16076226wfd.23' errormsg='authentication failed (GNU SASL, method PLAIN)' exitcode=EX_NOPERM I'm wondering if anyone else has encountered this. Google's extremely aggressive captcha does not help but I am able to log in now without a captcha from a browser so I'm open to any ideas why the simple switch of a user/password combo that is supposed to work does not. I'm also attaching my config so that others can see how to set things up.

  Read the article

• Samba - permission issue

  - by user88432

  I am trying to get samba to work properly... I have a "Movies" share (//server/Movies), I want only root account to be able to upload and delete. Guest can view "Movies" share without password/login but they cant delete/update (only view). [Movies] path = /mnt/user/Movies browsable = yes public = yes writable = no write list = root guest ok = yes I can access to Movies share as guest but when I try to add new file I get an error saying: "You need permission to perform this action" I expected username/password to popup but it didn't, how to fix this?

  Read the article

• Accessibility tools turn ON on boot screen EVERY TIME

  - by Tristan

  Hello, I wanted to do a joke to my teacher : When she left, she logged out and i set up all the accessibility tools (color blind, narrator.....) When she came back, she turn off her computer by letting the POWER button pushed. Ever since, each time she turns on the computer, all the accessibilty tools came up even if she DISABLES it each time. (@windows 7) Any solution before she kills me or i get fired from the school ? =o Thanks

  Read the article

• Screen recording in animated .gif format ( No sound needed)

  - by metal gear solid

  I need free and portable tool to record desktop activities in animated .gif format. i need gif video because it can run on web page without needing any plugin My os is windows XP and i need portable tool only. I want to record and save directly in gif format.

  Read the article

• Virtual PC network connection setting issue

  - by George2

  Hello everyone, I am using Virtual PC 2007 on Windows Vista Enterprise x86. My confusion is about the network setting for guest OS. In the network setting, I can set the network adaptor of guest OS to one of my physical network adaptors of my host OS (I have tested that it works for guest OS to use the physical network adaptor of host OS to access external network). But in this way, 1. since both host OS and guest OS will use the same physical network adaptor, will there be any conflicts (e.g. same H/W serves two OS)? 2. will guest OS share a part of network bandwidth of the host OS of the physical network adaptor? 3. What means NAT setting in guest OS network connection adaptor? thanks in advance, George

  Read the article

• CNTLM issue with intranet (maybe DNS)

  - by htorque

  On my Linux box I need to use an ISA proxy that requires authentication to reach the internet. I therefore installed CNTLM and configured it to point to the proxy address and listen on port 4321. I then configured my GNOME distribution to use localhost:4321 as global proxy for HTTP and HTTPS. The result: I can connect to the internet. I can ping intranet IPs, I do receive name resolution for intranet sites, yet I cannot ping them or open any intranet site in a browser (configured to use the distributions proxy) unless I use the site's IP address. I tried blocking the intranet IP range in the CNTLM config file without luck.

  Read the article

• NTPD issue - syncs then slowly loses ground

  - by ethrbunny

  RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

  Read the article

• mod_mono 'Service Temporarily Unavailable' issue

  - by Charlie Somerville

  I've deployed an ASP.NET web application on a Linux (Debian) server running Apache 2.2 and mod_mono 1.9 It's working well, however Mono occasionally segfaults and uses the entire CPU which causes the website to stop working and display 'Service Temporarily Unavailable' Killing mono fixes it, but obviously this isn't a good solution. I tailed the system log after this happened and I saw the following error messages from the kernel: Apr 20 01:49:37 charliesomerville kernel: [1596436.204158] mono[17909]: segfault at b645f671 ip b645f671 sp b4ffb604 error 4<6>mono[19047]: segfault at b645f66e ip b645f66e sp b4bf7604 error 4<6>mono[18017]: segfault at b645f66e ip b645f66e sp b52fe604 error 4<6>mono[19668]: segfault at b645f5e6 ip b645f5e6 sp b48f4604 error 4<6>mono[22565]: segfault at b645f674 ip b645f674 sp b45f1604 error 4<6>mono[17700]: segfault at b645f661 ip b645f661 sp b51fd604 error 4<6>mono[19596]: segfault at b645f5e6 ip b645f5e6 sp b49f5604 error 4 Apr 20 01:49:37 charliesomerville kernel: [1596436.208172] mono[23219]: segfault at b645f66e ip b645f66e sp b44f0604 error 4 At the end of Apache's error.log are the following errors: [Tue Apr 20 03:10:23 2010] [error] (70014)End of file found: read_data failed [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 [Tue Apr 20 03:10:23 2010] [error] Command stream corrupted, last command was 1 System.ArgumentNullException: null key Parameter name: key at System.Collections.Hashtable.get_Item (System.Object key) [0x00000] at System.Runtime.Serialization.SerializationCallbacks.GetSerializationCallbacks (System.Type t) [0x00000] at System.Runtime.Serialization.ObjectManager.RaiseOnDeserializingEvent (System.Object obj) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectContent (System.IO.BinaryReader reader, System.Runtime.Serialization.Formatters.Binary.TypeMetadata metadata, Int64 objectId, System.Object& objectInstance, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectInstance (System.IO.BinaryReader reader, Boolean isRuntimeObject, Boolean hasTypeInfo, System.Int64& objectId, System.Object& value, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObject (BinaryElement element, System.IO.BinaryReader reader, System.Int64& objectId, System.Object& value, System.Runtime.Serialization.SerializationInfo& info) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadNextObject (System.IO.BinaryReader reader) [0x00000] at System.Runtime.Serialization.Formatters.Binary.ObjectReader.ReadObjectGraph (System.IO.BinaryReader reader, Boolean readHeaders, System.Object& result, System.Runtime.Remoting.Messaging.Header[]& headers) [0x00000] at System.Runtime.Serialization.Formatters.Binary.BinaryFormatter.NoCheckDeserialize (System.IO.Stream serializationStream, System.Runtime.Remoting.Messaging.HeaderHandler handler) [0x00000] at System.Runtime.Serialization.Formatters.Binary.BinaryFormatter.Deserialize (System.IO.Stream serializationStream) [0x00000] at System.Runtime.Remoting.Channels.CADSerializer.DeserializeObject (System.IO.MemoryStream mem) [0x00000] at System.Runtime.Remoting.RemotingServices.GetDomainProxy (System.AppDomain domain) [0x00000] at System.AppDomain.CreateDomain (System.String friendlyName, System.Security.Policy.Evidence securityInfo, System.AppDomainSetup info) [0x00000] at System.Web.Hosting.ApplicationHost.CreateApplicationHost (System.Type hostType, System.String virtualDir, System.String physicalDir) [0x00000] at Mono.WebServer.VPathToHost.CreateHost (Mono.WebServer.ApplicationServer server, Mono.WebServer.WebSource webSource) [0x00000] at Mono.WebServer.ApplicationServer.GetApplicationForPath (System.String vhost, Int32 port, System.String path, Boolean defaultToRoot) [0x00000] at (wrapper remoting-invoke-with-check) Mono.WebServer.ApplicationServer:GetApplicationForPath (string,int,string,bool) at Mono.WebServer.ModMonoWorker.GetOrCreateApplication (System.String vhost, Int32 port, System.String filepath, System.String virt) [0x00000] at Mono.WebServer.ModMonoWorker.InnerRun (System.Object state) [0x00000] at Mono.WebServer.ModMonoWorker.Run (System.Object state) [0x00000] [Tue Apr 20 03:10:26 2010] [error] (70014)End of file found: read_data failed [Tue Apr 20 03:10:26 2010] [error] Command stream corrupted, last command was -1 Along with the above errors, Apache's error.log is packed with hundreds (if not thousands) of the following error: Maximum number (20) of concurrent mod_mono requests to /tmp/mod_mono_dashboard_default_2.lock reached. Droping request. At the moment, I'm thinking there might be something wrong with configuration here (it's basically running on out-of-the-box config)

  Read the article

• APC Smart UPS network shutdown issue

  - by Rob Clarke

  Here is a bit about our setup: We have 2x Smart-UPS RT 6000 XL units with network management cards We are running Powerchute from a network server Powerchute is connected to the management cards of both UPSs UPSs are set to do a graceful shutdown via Powerchute when the battery duration is under 20 minutes We also have a command file that runs with Powerchute Although our setup is redundant we do not have an equal load on each server due to APC switches for single power devices The problem is that as we do not have an equal load on each server the batteries drain at different rates. This means that the UPSs both get to the specified low battery duration at completely different times. The problem here is that UPS 1 may have run down to 5 minutes and is in desperate need of initiating a Powerchute shutdown - UPS 2 still has 25 minutes of runtime so no shutdown is initiated. Consequently UPS 1 goes down and takes all the servers with and then shuts down UPS 2 as well! What we need to happen are 1 of either 2 things: Powerchute initiates the shutdown as soon as either UPS reaches the 20 minutes low battery duration setting - and doesnt wait for both The UPS with the heavier load expends its entire battery but does not shutdown both UPSs and lets the load be switched across to the UPS that still has runtime remaining. That way when the UPS that still has runtime reaches its low battery duration it can proceed with the graceful shutdown via Powerchute. Hope that makes sense, any help is greatly appreciated!

  Read the article

• Mikrotik and NAT/Routing issue

  - by arul

  I have basic NAT/Routing problem with Mikrotik RB750 that I've been unable to solve over the past days. From our ISP we have 26 IP addresses: 10.10.10.192/27, with 10.10.10.193 being the gateway and 10.10.10.194 the first available IP. What I need is that everything connected to ether2 gets a public IP from the DHCP server, and everything connected to ether3 gets a local IP from another DHCP (192.168.100.0/24). All clients should have internet access (I'll figure out bandwidth throttling later) and optimally just 'see' each other (all boxes are Win7, I guess this can ultimately be handled with VPN). Here is my setup: ether1 (10.10.10.194) is connected directly to ISP. 20 clients connected to ether2(10.10.10.195), and another 20 to ether3(10.10.10.196) (both through same 24 port switches). This is my setup, which doesn't work, all 20 clients from ether2 can access the internet, though all comm. seems to come from 10.10.10.194 (is this due to the masquerade on ether1?), and ether3 can't access the internet at all. I think that I need to masquerade ether3, and SNAT/DNAT or NETMAP ether2, but that doesn't work either, I guess that I need to somehow 'wire' both ether2+3 to ether1. Address list: # ADDRESS NETWORK INTERFACE 0 ;;; public 10.10.10.194/32 10.10.10.192 ether1-gateway 1 ;;; inner DHCP 192.168.100.0/24 192.168.100.0 ether3-private 2 ;;; public 10.10.10.195/32 10.10.10.192 ether2-pub 3 ;;; public 10.10.10.196/32 10.10.10.192 ether3-private NAT 0 ;;; ether3 nat chain=srcnat action=src-nat to-addresses=10.10.10.196 src-address=192.168.100.0/24 out-interface=ether3-private 1 ;;; ether3 nat chain=dstnat action=dst-nat to-addresses=192.168.100.0/24 in-interface=ether3-private 2 ;;; ether1 masquerade chain=srcnat action=masquerade to-addresses=10.10.10.194 out-interface=ether1-gateway Routes: # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 A S 0.0.0.0/0 ether1-gateway 1 2 A S 10.10.10.192/27 10.10.10.195 ether2-pub 1 3 ADC 10.10.10.192/32 10.10.10.195 ether2-pub 0 ether1-gateway ether3-private 4 ADC 192.168.100.0/24 192.168.100.0 ether3-private 0 IP Pools: # NAME RANGES 0 public-pool 10.10.10.201-10.10.10.220 1 private-pool 192.168.100.2-192.168.100.254 DHCP configs: # NAME INTERFACE RELAY ADDRESS-POOL LEASE-TIME ADD-ARP 0 public-dhcp ether2-pub public-pool 3d 1 private-dhcp ether3-private private-pool 3d Thanks!

  Read the article

• Dependencies issue while installing Graphviz 2.28

  - by M. Saâd

  I want to install this packages for Nagvis : graphviz-2.28.0-1.el6.i686.rpm graphviz-doc-2.28.0-1.el6.i686.rpm graphviz-gd-2.28.0-1.el6.i686.rpm graphviz-graphs-2.28.0-1.el6.i686.rpm graphviz-perl-2.28.0-1.el6.i686.rpm But while installing, i have this error : # rpm -ivh graphviz-2.28.0-1.el6.i686.rpm erreur: Dépendances requises: libgdkglext-x11-1.0.so.0 est nécessaire pour graphviz-2.28.0-1.el6.i686 libglut.so.3 est nécessaire pour graphviz-2.28.0-1.el6.i686 libgtkglext-x11-1.0.so.0 est nécessaire pour graphviz-2.28.0-1.el6.i686 libgts-0.7.so.5 est nécessaire pour graphviz-2.28.0-1.el6.i686

  Read the article

• Debian + ProFTPD + LDAP Incorrect Password Issue

  - by Tristan Hall

  I have the LDAP configuration configured for ProFTPD and I have modified the modules.conf file to include the LDAP module. However, every time I login with FileZilla I get 530 Login Incorrect. It does this for all users except those whose passwords are defined locally as well as in LDAP. The exact same setup works fine on my CentOS server and I've already tried re-installing it after purging the configuration files.

  Read the article

• ubuntu 12.04 server and tftp access violation issue on put command

  - by SMYERS

  I installed tftp as per this document: http://icesquare.com/wordpress/solvedtftp-error-code-2-access-violation/ I followed this to the letter 3 times and every time I put a file I get: root@CiscoCFG:~# tftp localhost tftp put test Error code 2: Access violation tftp root@CiscoCFG:~# tftp localhost tftp put test Error code 2: Access violation If I touch the file name chmod 777 the file then do a put it works perfectly fine. My config is as follows: service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /svr/tftp disable = no } the directory /svr/tftp permissions are 777: drwxrwxrwx 3 nobody nobody 4096 Nov 14 10:32 svr This thing should have full permissions as would anyone who wanted to write or read from that directory. I see nothing in the logs im really stumped on this. If the file is already in the directory I can read it all day long, I just cant make NEW files, can not put them, but I can do get's, I can only put to an existing file with permissions @777. Thanks

  Read the article

• TimeZone Issue during DayLight Saving

  - by Viren

  I just been bugged by the Day light saving hours I seem that 3rd November 2013 01:00:00 start EST time Now ever Time I set my time to 3rd November 2013 00:58:xx(some seconds) and run date it give me valid Time zone i.e EDT but even after the time pass 01:00:00 and I still query the date library I still see the Time zone as EDT and not EST have a look at this screenshot You can clearly see the Time zone saying as EDT even when it is EST any one has a clue for this Update There is one other finding I found if I restart my machine I see this More Update Before Restart After Restart

  Read the article

• TimeZone Issue during DayLight Saving

  - by user1328293

  I just been bugged by the Day light saving hours I seem that 3rd November 2013 01:00:00 start EST time Now ever Time I set my time to 3rd November 2013 00:58:xx(some seconds) and run date it give me valid Time zone i.e EDT but even after the time pass 01:00:00 and I still query the date library I still see the Time zone as EDT and not EST have a look at this screenshot You can clearly see the Time zone saying as EDT even when it is EST any one has a clue for this Update There is one other finding I found if I restart my machine I see this

  Read the article

• Blue screen issue

  - by Jack

  I received several BSOD's that are recorded in the following logs: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 50 BCP1: FFFFF95FF8150C10 BCP2: 0000000000000008 BCP3: FFFFF95FF8150C10 BCP4: 0000000000000005 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-20030-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-33025-0.sysdata.xml ~~~~~ Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 1e BCP1: 0000000000000000 BCP2: 0000000000000000 BCP3: 0000000000000000 BCP4: 0000000000000000 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-32729-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-64319-0.sysdata.xml It seems to occur at random. I have gone 2 months without a BSOD, then I have gone a week with 10+ without changing what I am doing. This is my system: Windows 7 Professional 64-bit Gigabyte GA-890GPA-UD3H AMD Phenom II x6 1090T Processor 3.2GHz 8GB Ram(4X 2GB) Radeon HD 7850 2TB HDD Thermaltake 500W PSU I'm not sure about what the BSOD says, it just counts to 100 by 5's then restarts the computer. It happens fast and I have tried to get a picture before but to no avail.

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >