Search Results

Search found 46646 results on 1866 pages for 'operating system'.

Page 1257/1866 | < Previous Page | 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264  | Next Page >

• Partition and mount my secondary hard drive on CentOS 5.5 64bit?

  - by Andrew Fashion

  I am trying to prepare my second hard drive for user image uploads. Here is the current layout: # sudo parted /dev/sda print Model: ATA WDC WD2500KS-00M (scsi) Disk /dev/sda: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 8595MB 8488MB primary linux-swap 3 8595MB 10.7GB 2147MB primary ext3 4 10.7GB 250GB 239GB extended 5 10.7GB 250GB 239GB logical ext3 Information: Don't forget to update /etc/fstab, if necessary. I am assuming #4 is my secondary drive? How do I partition and mount it so I can begin using it? And how do I add to fstab? I understand if it's to many questions in one, just help me with whatever you can I guess :) Thank you for any help!

  Read the article

• Lost current user (shutdown/logoff) widget after upgrading to Ubuntu 10.04

  - by xyzman

  I've upgraded to 10.04 from 9.10. Everything went fine until I've rebooted. After reboot, I've received some message about status panel and being sleepy, dismissed it. However, I haven't seen the user widget on Gnome Panel since that. This image shows which widget I'm talking about. If some one has any ideas about how it's called properly, please share. http://img237.imageshack.us/img237/8274/sampleyu.jpg Anyway, the question is, how do I turn this panel (and ability to shut my system down without resorting to console) back?

  Read the article

• mpstat on slackware 13.0 shows no utilization

  - by conartist6

  As the title says, the mpstat command, executed on Slack 13.0 continuously shows almost no processor utilization of any sort. In fact none of the output ever seems to change at all. The system is dual processor board with two hyperthreaded P4 Xeons. Any ideas? 08:50:06 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s 08:50:06 PM all 0.38 0.00 0.03 0.03 0.00 0.00 0.00 99.56 1510.46 08:50:06 PM 0 0.50 0.00 0.05 0.10 0.00 0.01 0.00 99.33 11.90 08:50:06 PM 1 0.32 0.00 0.03 0.01 0.00 0.00 0.00 99.64 0.00 08:50:06 PM 2 0.38 0.00 0.03 0.01 0.00 0.00 0.00 99.58 0.00 08:50:06 PM 3 0.29 0.00 0.02 0.00 0.00 0.00 0.00 99.68 0.00 This is, literally, the only output I can get from the program. No values change ever.

  Read the article

• Windows 2003 to log on no matter how it turned off

  - by Arya

  I have a windows server 2003, which I use Teamviewer to connect to. When there is a power failure, and the computer restarts, it will not load Teamviewer. It gets stuck on a screen which asks why the computer was turned off. There is no keyboard or mouse connected to the server and I need Teamviewer to open every time. I don't want the screen asking why it was turned off to show up ever. I turned off Shutdown Event Tracker by doing the following: Open gpedit.msc Computer Configuration Administrative Templates System click Display Shutdown Event Tracker and then selected the disable radio button. Is this enough to prevent that screen to show up again? or is there anything else I need to change?

  Read the article

• How to run long time process on Udev event?

  - by neclude

  (sorry for my bad english) I want run ppp connection when my usb modem is connect. so i use next udev rule: ACTION=="add", SUBSYSTEM=="tty", ATTRS{idVendor}=="16d8",\ RUN+="/usr/local/bin/newPPP.sh $env{DEVNAME}" (my modem appear in /dev as ttyACM0) newPPP.sh: #!/bin/bash /usr/bin/pon prov $1 >/dev/null 2>&1 & Problem: udev event fire, newPPP.sh running, BUT newPPP.sh process will be killed after ~4-5s. ppp not have time to connect. (in it params is timeout 10s for dial up). How can i run long time process, that will not be killed? (I was try nohup. It don't work too.) System: Arch Linux

  Read the article

• Can't see a Windows XP computer on the network

  - by user56614

  I have two PC's connected to the same router. One is running Vista Home Premium and the other is running XP Pro. I'm trying to reach the shares of second PC from the first PC. I've enabled file sharing on the XP PC, I've disabled firewall and defender, and I can successfully ping it from the Vista PC. Both computers are set to the same workgroup "WORKGROUP". However, if I try to type "\\192.168.1.2" in Windows Explorer (192.168.1.2 being the IP address of the XP PC), I get a message: "Windows can't access \\192.168.1.2... Error code: 0x80004005 Unspecified error". And If I type "net view \\192.168.1.2" in command prompt, I get "System error 53 has occurred. The network path was not found." Am I missing something trivial?

  Read the article

• Documenting software-updates semi-automatically in MacOS X by parsing log files?

  - by Martin

  I'd like to document changes I made to my computer (running MacOS 10.6.8) to be able to identify the sources of eventual problems. Mostly I install updates when a software notifies me about a newer version and offers me a dialog to download and install the update. Currently I'm documenting those updates "by hand" by noting in a text file, when I have e. g. installed a Flash-Player update or updated another 3rd party software ... I wonder if I could achieve that easier and semi-automatically by parsing system logfiles for certain texts like "install" and that way directly get the relevant information: what has been installed (Software and version) when has been installed where has it been installed/what has changed Is there a way to extract such information by a script from the existing logfiles?

  Read the article

• Switching to Chrome from IE

  - by Alan Parrish

  Hi, I work in IT at a school and we recently updated our database software, however the web access that the teachers use to do registration does not work too well with Internet Explorer 7 and we're thinking about switching to chrome (mostly due to me hating IE in general) but the problem we have is that users are unable to migrate their bookmarks over from IE due to account restrictions, is there any way to get this working? A bit of info about the system if it could be helpful; Almost all the client PCs are running Win XP SP2. My colleagues machines are running Windows 7, I use OS X Snow Leopard and most of out servers are running windows server 2003 (with the exception of 2 one on 2000 server and another on 2008 R2). The Active Directory Controller is running Windows Server 2003

  Read the article

• Virtualise Excel in a browser

  - by Macros

  Is it possible to give users access to a virtualised instance of Excel - I don't want to give them access to a full OS (although this will clearly be running in the background, all they can access is Excel - they don't even see any other screens)? Secondly, if it is possible, is it possible to do within a browser? Edit I am building a system which is designed to test candidates skills in Excel and for this reason needs to use the full desktop version and not a web app. I don't want to have to ensure Excel is installed on the client machine as there will be issues around differing versions and security as the workbook(s) that are used in the test use VBA extensively to customise and mark the exercises. Ideally my web app would be able to open a session to the server which then just puts the user into an instance of Excel without ever seeing a desktop. I would also need to be able to pass in command line parameters in order to define which workbook to open and also pass in a unique token to identify the user

  Read the article

• How can I fix a computer that is literally too slow to do anything?

  - by fredley

  I'm troubleshooting a Windows 7 PC for a friend. A couple of days ago it started running 'slow'. It turns out 'slow' is about 15 minutes to the first glimpse of the desktop, and another 30 to show icons. It is possible to open Task Manager, and nothing seems awry, CPU usage at 1-5%, plenty of memory free. The machine is clearly infested with malware though, in particular a program called 'Optimizer Pro' is demanding money to 'remove 5102 files slowing down my computer'. This seems highly suspicious. My problem is though, that I can't access msconfig (I left it for a couple of hours after having hopefully typed it into the Start Menu and hit enter - nothing seems to have loaded), or anything at all basically. I can boot from a Linux Live CD, but can I actually do anything useful from there? System Restore hasn't fixed it either, and Safe Mode exhibits the same behavior.

  Read the article

• How can I determine Breaking point of my Web application using JMeter?

  - by Gopu Alakrishna

  How can I determine Breaking point of my Web application using JMeter? I have executed the JMeter Testplan with different concurrent users load. EX. 300 users(0% error), 400 users(7% error in a sample, 5% error in another sample), 500 users(more than 10% error in 4 out of 6 samples). At What value of % Error, I can say system reached the Breaking point.I used concurrent users 300, 400, 500 in a PHP website. Should I consider any other parameter to determine breaking point. How many maximum concurrent users my application can support?

  Read the article

• Do memory cards have any max file size limitation?

  - by Dmitriy R

  I am not sure where to ask this question, so perhaps it is physical limitation. I have a 8 GB flash micro SD memory card. When I copy any file size of up to few gigabytes, copying happens normally. But if I am trying to copy file over 4 GB file, then the system tells me like insufficient memory on card, although 8 GB is available. So perhaps only 32 bit address is used for keeping size of file in micro SD card, or is my micro SD defective?

  Read the article

• Squid3 not working. Access denied.

  - by Nitish

  I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

  Read the article

• Best way to backup Active Directory with a single domain controller

  - by John Hall

  I have a domain with about 15 users and a single Windows Server 2008 domain controller. Some recent issues with my RAID controller have made me reconsider how I go about securing the AD data. Currently I run a System State Backup nightly. However, it seems that it is impossible (or at least difficult and unsupported) to restore that to any other machine than the one from which it was taken. Adding a second DC to the domain seems expensive and overkill for such a small network. Is there no other way to backup the AD data?

  Read the article

• Hardware recommendations for building an Ubuntu encrypted file server

  - by Robert Mashlan

  I would like to build a file server for my home network using Ubuntu. It will serve files from RAID1 configured disks, either in the OS or in hardware. It will be connected to a Gigabit ethernet LAN. The disks will use an encrypted file system. It will serve samba shares. I would like a recommendation on what kind of processing power/memory I would need to build a box that would be able to sustain the full capacity of the Gigabit ethernet connection in a file transfer for a single connection with the overhead of serving from an encrypted disk. I'm not looking to build a dream server, I just want enough processing capacity for high performance (and reliable) file sharing and spend as little as possible for it. This may be tangential, but what kind of hardware would I need to have a server be able to reliably go into a low power mode when no requests are being made of it?

  Read the article

• Recover Bios HP DV9700T windows 7 64

  - by petebob796

  I downloaded the latest DV9700t bios (.59) and ran the update tool in windows 7 64. This seemed to go ok and did the usual system will shutdown in 10 seconds dialog. Updon the reboot nothing happens I get no BIOS screen or anything so I think the bios update went wrong. Which I am annoyed about I have never known a bios update to fail before and lots of people on the internet seem to have had the same problem with the same model. There is a way to recover apparently using crisdisk utility and creating a bootable usb key then holding win+b at power on, unfortunately the utility to make the disk doesn't seem to work in 64 bit versions of windows, the only type I have easy access to. Anyone know a way to create the boot disk in 64?

  Read the article

• DisplayPort to DVI not working on Quadro FX 580

  - by kaosvid

  I have a PNY NVIDIA Quadro FX 580 graphics card with 1x DVI and 2x DisplayPorts. The DVI port works fine with both my Viewsonic monitors but I cannot get either of the DPs to work using the supplied DP to DVI adapter; all I get is a "no signal" on either monitor when connected to either DP port. The NVIDIA Control Panel shows that the second monitor is not connected when in fact it is. How do I get the second monitor to work? System: Windows XP Professional 32-bit Asus P5Q motherboard Core 2 Duo E8500 CPU 4GB PC8500 RAM

  Read the article

• SQL server could not connect: Lacked Sufficient Buffer Space...

  - by chumad

  I recently moved my app to a new server - the app is written in c# against the 3.5 framework. The hardware is faster but the OS is the same (Win Server 2003). No new software is running. On the prior hardware the app would run for months with no problems. Now, in this new install, I get the following error after about 3 days, and the only way to fix it is to reboot: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full.) I have yet to find a service I can even shut down to make it work. Anyone had this before and know a solution?

  Read the article

• Vim: How can I :cd to an sftp directory?

  - by ChrisInCambo

  Hi, I'm currently an emacs user, but thought I would come back and take another look at Vim for fun. My client machine is Ubuntu, and I frequently work on other ubuntu servers within my network, emacs and tramp is really nice in this regard, I can just connect to a file via sftp and then easily navigate to it's parents/children/sibling, just as if I was dealing with a file on the local file system. With Vim I can sftp to a file, but none of the navigation stuff works, when I use :e or fuzzy file search, vim still thinks I'm back on the client machine. If I try to :cd to the sftp directory I get an error. Is there anyway I can get the same file/folder navigation regardless of whether I'm looking at an sftp folder or a folder on my client machine? Cheers, Chrsi

  Read the article

• Can I delete the OEM partition on the new Dell XPS 15?

  - by timepilot

  My new Dell XPS 15 L521X just arrived. I need to set this up to dual boot Linux. Sadly, the system comes with four primary partitions. I can't do a clean install at the moment, so one of the partitions will have to be deleted before I can install Linux. The layout is as follows: OEM: 39mb Hibernation: 8gb OS: 457gb Recovery: 12gb Obviously, I can't delete the Hibernation and OS partitions (will shrink to make space for Linux) and I'd like to keep the recovery partition if possible. So my question is what is on the small OEM partition? What functionality will I lose if I delete it?

  Read the article

• Can I use VT-D with a windows host for a VM?

  - by Journeyman Geek

  I've got a fairly beefy gaming system that I also run occational virtual machines on. It runs windows 8 and the built in hyper V virtual machine software at the moment and has a core i7 3770 (which unlike the unlocked model, should support VT-D), an Asus P8Z77V and a gforce 660 video card(also asus). I figure that if I could use VT-D I could add a cheap dedicated 3d card for a VM, in case I wanted somewhat more than the 'basics'. I know KVM and Xen support this to some level on linux, but can I do so on windows? I'm open to switching VM software if need be.

  Read the article

• Windows Security popup window pops up each time any connection is made

  - by MC Emperor

  I have a problem with the Windows Security popup below. It pops up every time the system tries to make connection with any internet source. It's very annoying, and I don't know how to resolve the problem. (The popup window below is in Dutch, but says something like Connect to somedomain.com. Then it expects you to give your credentials.) I am running on a Windows 7 x64 OS. Now how do I solve this problem? Is it a Windows Firewall problem?

  Read the article

• UID uniqueness of IMAP mails

  - by SecStone

  In our internal webmail system, we'd like to attach notes and contacts to certain mails. In order to do this, we have to keep track of every mail on our IMAP server. Unfortunately the IMAP standard doesn't enforce the uniqueness of the UID of a mail in a mailbox (just in subfolders). Is there any tool/IMAP server which generates UIDs which are truly unique? Or is there any other way how we can identify each mail? (the Message-ID header field is not unique as some mails do not contain such a field). Additional resources: Unique ID in IMAP protocol - Limilabs.com

  Read the article

• iMac with Mountain Lion and Mavericks

  - by bob

  I have been starting up my iMac (Mavericks) with a flash drive that boots up Mountain Lion so that I can use an app that is incompatible with Mavericks. Question: I have a single external backup drive always connected to my Mac. I am thinking of partitioning that drive and giving each partition a unique name, e.g., Backup 1 and Backup 2. I intend then to boot up in Mavericks and tell Time Machine to back up to Backup 1, and then boot up in Mountain Lion and tell Time Machine to back up to Backup 2. Will this work, i.e., will the appropriate partition automatically back up the system in which it is booted?

  Read the article

• Best practice for administering a (hadoop) cluster

  - by Alex

  Dear all, I've recently been playing with Hadoop. I have a six node cluster up and running - with HDFS, and having run a number of MapRed jobs. So far, so good. However I'm now looking to do this more systematically and with a larger number of nodes. Our base system is Ubuntu and the current setup has been administered using apt (to install the correct java runtime) and ssh/scp (to propagate out the various conf files). This is clearly not scalable over time. Does anyone have any experience of good systems for administering (possibly slightly heterogenous: different disk sizes, different numbers of cpus on each node) hadoop clusters automagically? I would consider diskless boot - but imagine that with a large cluster, getting the cluster up and running might be bottle-necked on the machine serving the OS. Or some form of distributed debian apt to keep the machines native environment synchronised? And how do people successfully manage the conf files over a number of (potentially heterogenous) machines? Thanks very much in advance, Alex

  Read the article

< Previous Page | 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264  | Next Page >