Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 126/370 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

  • What Wireless Router/ADSL Modem to get? N-band a must!!

    - by JJarava
    I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

    Read the article

  • I Made Wordpress Multisite. And Now Everything Doesn't Display Properly

    - by piratepartypumpkin
    I installed Ubuntu 10.4 then I installed Bitnami LAMP stack then I installed bitnami wordpress module then I tried to make the site into a multisite by following these instructions: http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite#How_to_add_several_WordPress_Multisite_blogs_with_different_domains.3f AND http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite I can elaborate if needed: I enabled multisite in my wp-config.php file. Then I created a network using the wordpress dashboard. I was given two blocks of text to copy and paste 1 block into my wp-config.php file and one into my .htaccess file. I did that and now I get this: When I go to my mywebsite.com I get this (this was there before I switched to multisite): If I go to mywebsite.com/wordpress I get this (this used to be a functioning wordpress theme): If I click on "My Blog" it redirects to 1mywebsite.com (where the "1" came from I have no idea) If I try to login by going to mywebsite.com/wordpress/wp-login I get this: and if I enter my user and password it redirects me to mywebsite.com/wp-login.php and gives me "Not Found" The requested URL /wp-login.php was not found on this server. NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName mywebsite.com ServerAlias www.mywebsite.com </VirtualHost>

    Read the article

  • How should I isolate computers with different roles on a network

    - by fishhead
    I work in an industrial plant and we have one network(physical wire) that us used for both office usage and for process systems. The office computers are only used for typical office needs but occasionally do connect to the process computers to obtain information from a sql server or for some other purpose. A new initiative is in the works and is rolling down hill from corporate and that is to standardize how the the computers are used at work and they would be severely locked down and only a standard set of applications will be allowed to execute. one of the requirements is to also have non office computers isolated from the company domain. our non-office computers are a mix of Man-Machine interfaces and sql-servers all running software that non standard. My question is, how can we divorce the control systems computers from the company domain but still have access to the servers from the company domain. thanks

    Read the article

  • How should I isolate computers with different roles on a network

    - by fishhead
    I work in an industrial plant and we have one network(physical wire) that us used for both office usage and for process systems. The office computers are only used for typical office needs but occasionally do connect to the process computers to obtain information from a sql server or for some other purpose. A new initiative is in the works and is rolling down hill from corporate and that is to standardize how the the computers are used at work and they would be severely locked down and only a standard set of applications will be allowed to execute. one of the requirements is to also have non office computers isolated from the company domain. our non-office computers are a mix of Man-Machine interfaces and sql-servers all running software that non standard. My question is, how can we divorce the control systems computers from the company domain but still have access to the servers from the company domain. thanks

    Read the article

  • Planning home network

    - by gakhov
    I'm planning to setup my home network from scratch and want to ask professional opinions or tips. My home is connected to Internet with a cable connection (100 Mb/s). The devices I would like to connect are VoIP phone (RJ-45), TV (WiFi/LAN), 3 laptops (WiFi), 2 smartphones (WiFi), an iPad (WiFi), a Kindle (WiFi), a network printer and, probably, a home media storage (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, I need help to choose the best router (or combination of routers) to support stable connections for all these devices and minimize the total number of routers/adapters. I like how Cisco/Linksys devices were working for me in the past, so preferably (but not obligatorily) I want to setup network with their solutions. Any thoughts?

    Read the article

  • Mac claims to have connected to wireless network, but hasn't

    - by Mick
    I am attempting to connect a new mac OSX 10.6.5 laptop to a wireless network (I am a windows expert but a mac novice). It used to connect without problem to the network when I had the security set to "64 bit wep". Now I have changed the security on my belkin router to "WPA-PSK (no server)". I have two PC's and an old mac connecting via the new security setting without problem. Now I have the problem that on the new mac, the wireless icon is indicating a good connection (5 dark bars). Also the network name has a tick next to it on the wireless drop down menu. But I can not view any websites. I can not even connect to the router by typing 192.168.2.1 into a browser address bar. Any ideas where I went wrong?

    Read the article

  • How do I create a wifi network bridge with qemu on OS X?

    - by a paid nerd
    I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

    Read the article

  • What services does hosts.allow NOT affect?

    - by Jed Daniels
    I know that hosts.allow and host.deny only affect things that are tcpwrappered, but what does this mean in practice? It seems that most people use hosts.allow to handle ssh and nfs blocking, but what other services are typically handled there? And what services AREN'T typically handled there? Edit: ok, I realize I did a terrible job of explaining what I was after. No, I'm not interested in knowing if a particular service can be handled by hosts.allow, I want to know if a service will be handled. For example, if I do an lsof -i, I get a nice list of things that are listening for connections to my box. I want to know which ones will be affected if I go stick an entry into hosts.allow (well, I really want to know which ones won't be affected).

    Read the article

  • Why DELL PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

    - by Kedare
    Hello ! I have a little question, I'm actually studing IT in France, and when looking on alternative on the very [...] very expensive Cisco equipments, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipments in France :( Thank you !

    Read the article

  • wi-fi connection drops periodically for a few seconds

    - by sergiom
    I've read the similar question on wireless connections dropping, but no answer seems to apply to my case I have configured the wi-fi lan of my router to broadcast sid and use WPA-PSK. Every few minutes my wi-fi connection drops for a few seconds and then restores. When I use two computers and run a ping -n 50000 on both computers, I see that the connection drops at different times but with almost the same rate. the router is a zyxel, one pc runs windws vista and uses a USB wi-fi device from Belkin: F6D4050 the other one runs windows 7 is a Dell PC with an Intel(R) WiFi Link 5100 AGN there are no other wi-fi lans around

    Read the article

  • Cisco Catalyst 4500 Policy Based Routing

    - by Logan
    In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

    Read the article

  • PXE Boot not working

    - by Nishant
    Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

    Read the article

  • Router recommendation to virtualize 800 IPs

    - by delerious010
    I've recently been looking at getting some new load balancers for our environment as we are expecting to double our client base in the next 12 months. Currently we have 400 public IPS serving 800 clusters ( 2 clusters / IP due to ports ) on Coyote Point Balancers, and distributing connections to 3 web servers serving about 6GBytes outgoing, 2Gbytes in per day. If we double, this would be about 800 IPs, possibly 1600 clusters, and about 6 servers per cluster ( for a total of 9600 so called "real servers" using Barracuda's lingo ). Due to the amount of clusters, most solutions I've looked at ( Coyote, Barracuda, Loadbalancer.org ) seem to be unsure whether they'll be able to handle our planned growth, mostly due to health checks performed on the servers ... which makes total sense when you think of it. So the fine folk at loadbalancer.org recommended that we may be better off offload the 400-800 public IPs, which we require for SSL eCommerce solutions, over to a forward facing router. From that point on, the router could do some mangling to route EXT_IP:443 to INT_IP:INT_PORT which would then allow us to reduce the Load Balancer configuration to 1 or 2 clusters, thus resolving the health check problem. Does this idea make sense to yall ? Or would you have other recommendations to make ? Secondly, what router would you recommend for such an undertaking ? I'd be looking at something that has some form of failover mechanism built in. On a totally unrelated note, I've got to admit that I'm extremely pleased with the responses I got from loadbalancer.org. Their responses to my inquiries were surprisingly helpful ( i.e. I didn't feel as if I was taking to a sales guy trying to push something ). ( No I don't work for them, and sadly nor are they sending me free gear ).

    Read the article

  • Force10 S60 remote management

    - by StaringSkyward
    We've got a Force10 S60 switch to replace an older Cisco. I can't find a way to give the switch itself an IP address on the local VLAN so I can ssh to it. The config guide talks about using either a management interface on a separate management network or dedicating e.g. a gigabit port as a management port with a dedicated IP address. Ideally I would like to do what we do currently with the Cisco switches, which is in effect give the entire switch an IP so it can be reached from any host on the same VLAN without having to use up a physical port on the switch or physically connect the management port to another device. Is this possible with the S60 and if so, how would you give it, say the address 10.0.1.1 in vlan 10 (10.0.1.1/24)? Thanks!!!

    Read the article

  • WPA Enterprise Wireless Bridge

    - by prestomation
    I live in college housing at a university with wifi available. unfortunately, my bedroom(where I'd like to place my PC) gets little to no reception. I'd like to place a router in the strongest spot and rebroadcast. I understand this can be done with DD-WRT/etc, but this particular network is WPA Enterprise with my own personal username/password. I can't find any concrete evidence that I can get my router to act as a repeater for this encryption. I don't currently have a router to test it on, otherwise this would be easy, I just don't want to buy a router if it will be worthless to me. Thanks for your help

    Read the article

  • snmptt not translating traps, even with translate_log_trap_oid=1

    - by mbrownnyc
    I am having some trouble configuring snmptt to properly translate snmp traps. The following is a problem: /etc/snmp/snmptt.conf reflects: EVENT fgFmTrapIfChange .1.3.6.1.4.1.12356.101.6.0.1004 "Status Events" Critical FORMAT $* EXEC /usr/local/nagios/libexec/eventhandlers/submit_check_result $r "snmp_traps" 2 "$O: $+*" "$*" SDESC Trap is sent to the managing FortiManager if an interface IP is changed Variables: 1: fnSysSerial 2: ifName 3: fgManIfIp 4: fgManIfMask EDESC when a trap is received, /var/log/messages reflects: Sep 6 12:07:32 SNMPMANAGERHOST snmptrapd[15385]: 2012-09-06 12:07:32 <UNKNOWN> [UDP: [192.168.100.2]:162->[192.168.100.31]]: #012.1.3.6.1.2.1.1.3.0 = Timeticks: (707253943) 81 days, 20:35:39.43 #011.1.3.6.1.6.3.1.1.4.1.0 = OID: .1.3.6.1.4.1.12356.101.6.0.1004 #011.1.3.6.1.4.1.12356.100.1.1.1.0 = STRING: FGTNNNNNNNNN #011.1.3.6.1.2.1.31.1.1.1.1.10 = STRING: internal4 #011.1.3.6.1.4.1.12356.101.6.2.1.0 = IpAddress: 192.168.65.100 #011.1.3.6.1.4.1.12356.101.6.2.2.0 = IpAddress: 255.255.255.0 Sep 6 12:07:37 SNMPMANAGERHOST icinga: EXTERNAL COMMAND: PROCESS_SERVICE_CHECK_RESULT; 192.168.100.2; snmp_traps; 2; enterprises.12356.101.6.0.1004: enterprises.12356.100.1.1.1.0:FGTNNNNNNNNN ifName.10:internal4 enterprises.12356.101.6.2.1.0:192.168.65.100 enterprises.12356.101.6.2.2.0:255.255.255.0 Since the icinga entry reflects the EXEC, it's obvious there is no translations occurring by snmptt. I have verified that translate_log_trap_oid and net_snmp_perl_enable is enabled in snmptt.ini When using --debug=1 to start snmptt, I see the following in the --debugfile: ********** Net-SNMP version 5.05 Perl module enabled ********** The main NET-SNMP version is reported as NET-SNMP version: 5.5. What else can be done to verify that snmptt is configured properly to translate traps? I have run snmptt-net-snmp-test to verify whatever net-snmp-perl version I have installed properly supports translations. The output indicates it does. /root/snmptt_1.3/snmptt-net-snmp-test --best_guess=2 SNMPTT Net-SNMP Test v1.0 (c) 2003 Alex Burger http://snmptt.sourceforge.net MIBS:RFC1213-MIB best_guess: 2 Testing translateObj ******************** Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=disabled Test passed. Result: sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=enabled Test passed. Result: RFC1213-MIB::sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=disabled Test passed. Result: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=enabled Test passed. Result: RFC1213-MIB::.iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing getType *************** Testing: .1.3.6.1.2.1.4.1 Test passed. Result: INTEGER Testing: ipForwarding Test passed. Result: INTEGER Testing Description ******************* Test passed. Result: ------------------------------------------------- The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. ------------------------------------------------- I have manually gone through the MIB with the definition that's not resolving, and verified that it is properly linking back to the proper resolved definition. It is: FORTINET-FORTIGATE-MIB.txt contains: fgFmTrapIfChange NOTIFICATION-TYPE OBJECTS { fnSysSerial, ifName, fgManIfIp, fgManIfMask } STATUS current DESCRIPTION "Trap is sent to the managing FortiManager if an interface IP is changed" ::= { fgFmTrapPrefix 1004 } fgFmTrapPrefix OBJECT IDENTIFIER ::= { fgMgmt 0 } fgMgmt OBJECT IDENTIFIER ::= { fnFortiGateMib 6 } fnFortiGateMib ::= { fortinet 101 } IMPORTS FnBoolState, FnIndex, fnAdminEntry, fnSysSerial, fortinet FROM FORTINET-CORE-MIB fortinet MODULE-IDENTITY ::= { enterprises 12356 } LOOKS GOOD!!!!! 1.3.6.1.4.1.12356.101.6.0.1004 I've exhausted all the documentation and even posted fruitlessly in the snmptt-users mailing list. I can not prove it is the MIB. Why would snmptt fail to translate traps? Thanks, Matt

    Read the article

  • windows Home Server backup error

    - by domen
    I've finally built my WHS, but some other problems have showed up. I've googled, binged and searched SU with no success. The problem is following: at the moment I've got a Win7 laptop and Win7 PC, which should be backed up by the WHS. Laptop is backed up just fine with no issues, but when I try to manually backup the PC, after "backup is starting" message, when backup service should be monitoring changes on partitions, PC gets disconnected from the home network and thus, the backup process is stuck. Disabling/enabling network adapter gets PC back on the network. The only thing I've tried was reinstalling connector software. no success. Also, I've downloaded connector troubleshooter and only thing it says is "DHCP server was not found". I'm not good with networks, so I couldn't figure out what could that indicate (all computers in the network are assigned static IPs). Any ideas what the problem can be? I can provide any additional information, I'm just not sure what may be helpful right now. Thanks.

    Read the article

  • What are the challenges when my enterprise desires to move the processing component of an applicatio

    - by Berkay
    Assume that i have an enterprise accounting application that consists of a front-end interface, a processing tier, and a back-end database. This is an application that contains private business data, and thus is traditionally run in a secure private network environment within the enterprise. What are the challenges that appear when my enterprise desires to move the processing component of this application to a cloud computing data center in order to achieve greater scalability or to reduce IT costs ? Pls note: do i have to make significant changes to my own infrastructure to enable external access to formerly private resources? do i have to modify the application code to handle new network topology ? thanks, if you give your answers in a simple manner, really appreciated.

    Read the article

  • Can't connect to wireless-n in dual mode.

    - by Tyllyn
    I recently purchased a Acer Aspire Revo AR3610-U9022. This little nettop uses a Atheros AR5B91 Wireless Network Adapter. I also have a Netgear RangeMax NEXT Wireless Route (model WNDR3300). I have been using this router in dual mode (11G and 11N) on my normal desktop without a problem (Mode: Up to 270Mbps at 5GHz & 54Mbps at 2.4 GHz), but doing this, my Revo won't detect the 11N network as being around... my desktop still does, but the Revo, nope... just the 11G. However, when I switch my router over to just "Up to 270Mbps at 2.4GHz", it kills the 11G entirely, but the Revo recognizes the 11N network. I'm a programmer by trade, and this hardware-y stuff confuses me more than it should. Is there any way that I could set this stuff up so my Revo can connect to the 11N part of my router, but keep the 11G around? :) Thanks!

    Read the article

  • Host spreads wrong MAC Adress of router on the WIFI

    - by JavaIsMyIsland
    Strange things are going on our network. Since yesterday a host which is actually not on our subnet spreads wrong ARP Replys on our network. To be precise, only on the WIFI. If I connect my Laptop to the cable ethernet, it gets the right MAC adress of the router. Also my Android phone and my Ubuntu system do get the right MAC Adress. So I took a look at wireshark. When I clear the ARP cache of the windows machine, the first ARP response is correct and comes from the router. But like 10 ms later another ARP response comes from another host in the WIFI. The host changes its IP Adresses from time to time and they look like they are not on our subnet. So I can not use the internet because DNS is not working anymore. Sometimes the router wins the race condition and the mac adress is set correctly in the arp cache. I first thought, this is an arp-poisoning mitm attack but it does not make sense if the packets get not routed correctly?! I restarted the router but it didn't help. I have no access to the router, else I would change the shared key to make sure there is no intruder on the wifi.

    Read the article

  • Throughput; capacity planning help for C10K like design

    - by z8000
    I am designing a network service in which clients connect and stay connected -- the model is not far off from IRC less the s2s connections. I could use some help understanding how to do capacity planning, in particular with the system resource costs associated with handling messages from/to clients. There's an article that tried to get 1 million clients connected to the same server [1]. Of course, most of these clients were completely idle in the test. If the clients sent a message every 5 seconds or so the system would surely be brought to its knees. But... How do you do less hand-waving and you know, measure such a breaking point? We're talking about messages being sent by a client over a TCP socket, into the kernel, and read by an application. The data is shuffled around in memory from one buffer to another. Do I need to consider memory throughput ("5 GT/s" [2], etc.)? I'm pretty sure I have the ability to measure the basic memory requirements due to TCP/IP buffers, expected bandwidth, and CPU resources required to process messages. I'm a little dim on what I'm calling "thoughput". Help! Also, does anyone really do this? Or, do most people sort of hand-wave and see what the real world offers, and then react appropriately? [1] http://www.metabrew.com/article/a-million-user-comet-application-with-mochiweb-part-3/ [2] http://en.wikipedia.org/wiki/GT/s

    Read the article

  • Sharing a printer over the net from Windows 7 to Windows Server 2003

    - by Grant Unwin
    Hi, I need to share a printer that is connected to a Windows 7 computer. The windows 7 computer is in another building about an hours drive away. The computer that needs to access the printer is running Windows Server 2008. Ive tried setting the printer as 'shared' for 'everyone' on the Windows 7 PC and accessing it from the server by adding a TCP/IP port to the IP address but the printer just wont add. From googling aparently it may need setting up as a printer server through IIS, but i'm just not sure on the best practice. Any help greatly appreciated. Thanks Grant Unwin

    Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >