Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 131/172 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

• NVidia ION and /dev/mapper/nvidia_... issues.

  - by Ritsaert Hornstra

  I have an NVidia ION board with 4 SATA ports and want to use that to run a Linux Server (CentOS 5.4). I first hooed up 3 HDs (that will be a RAID5 array) and a forth small boot HD. I first started to use the onboard RAID capability but that does not work correctly under Linux: the raid capacity is not a real RAID but uses lvm to define some arays. After setting the BIOS back to normal SATA mode and whiping the HDs, the first boot harddisk (/dev/sda) is seen as /dev/sda BEFORE mounting and after mounting as /dev/mapper/nvidia_. CentOS is unable to install on it (and grub is not installable on it either). So somehow the harddisk is still seen as if it belongs to some lvm volume. I tried to clean out the HD by issuing a few dd if=/dev/zero of=/dev/sda commands to wipe the starting cylinders and final cylinders but to no avail. Did anyone see this problem and did anyone find a solution? UPDATE When I create only a single ext3 partition on the first HD (/dev/mapper/nvidia_...) no LVM partitions are seen and I can boot from /dev/mapper/nvidia_.... Now the next step is to see how I can get rid of this folly.

  Read the article

• Redmine install not working and displaying directory contents - Ubuntu 10.04

  - by Casey Flynn

  I've gone through the steps to set up and install the redmine project tracking web app on my VPS with Apache2 but I'm running into a situation where instead of displaying the redmine app, I just see the directory contents: Does anyone know what could be the problem? I'm not sure what other files might be of use to diagnose what's going on. Thanks! # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "/var/log/apache2/foo.log" # with ServerRoot set to "" will be interpreted by the # server as "//var/log/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs-2.1/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # #<IfModule !mpm_winnt.c> #<IfModule !mpm_netware.c> LockFile /var/lock/apache2/accept.lock #</IfModule> #</IfModule> # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 15 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog /var/log/apache2/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf # Include all the user configurations: Include /etc/apache2/httpd.conf # Include ports listing Include /etc/apache2/ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # # Define an access log for VirtualHosts that don't define their own logfile CustomLog /var/log/apache2/other_vhosts_access.log vhost_combined # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ # Enable fastcgi for .fcgi files # (If you're using a distro package for mod_fcgi, something like # this is probably already present) #<IfModule mod_fcgid.c> # AddHandler fastcgi-script .fcgi # FastCgiIpcDir /var/lib/apache2/fastcgi #</IfModule> LoadModule fcgid_module /usr/lib/apache2/modules/mod_fcgid.so LoadModule passenger_module /var/lib/gems/1.8/gems/passenger-3.0.7/ext/apache2/mod_passenger.so PassengerRoot /var/lib/gems/1.8/gems/passenger-3.0.7 PassengerRuby /usr/bin/ruby1.8 ServerName demo and my vhosts file #No DNS server, default ip address v-host #domain: none #public: /home/casey/public_html/app/ <VirtualHost *:80> ServerAdmin webmaster@localhost # ScriptAlias /redmine /home/casey/public_html/app/redmine/dispatch.fcgi DirectoryIndex index.html DocumentRoot /home/casey/public_html/app/public <Directory "/home/casey/trac/htdocs"> Order allow,deny Allow from all </Directory> <Directory /var/www/redmine> RailsBaseURI /redmine PassengerResolveSymlinksInDocumentRoot on </Directory> # <Directory /> # Options FollowSymLinks # AllowOverride None # </Directory> # <Directory /var/www/> # Options Indexes FollowSymLinks MultiViews # AllowOverride None # Order allow,deny # allow from all # </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /home/casey/public_html/app/log/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog /home/casey/public_html/app/log/access.log combined # Alias /doc/ "/usr/share/doc/" # <Directory "/usr/share/doc/"> # Options Indexes MultiViews FollowSymLinks # AllowOverride None # Order deny,allow # Deny from all # Allow from 127.0.0.0/255.0.0.0 ::1/128 # </Directory> </VirtualHost>

  Read the article

• Multiple public IPs through DD-WRT without 1-to-1 NAT

  - by Stephen Touset

  I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

  Read the article

• iPhone Remote with iTunes Library via VPN

  - by sudo work

  Alright, so I'm currently behind a network router (not under my control). The router performs NAT and somehow prevents a computer from scanning other nodes. At least, you're unable, in this instance, to locate an iTunes library. You can, however, communicate with a node's open ports if the local IP address is known, as well as the port. I haven't actually tried port scanning a specific IP using nmap or another tool yet. So I've tried one solution to remove the contribution of the router entirely (to verify that it works without the influence of the routers). I set up an access point using my iPhone and tethered my computer (with the library) to it. From here, I was able to pair my library and the iPhone Remote application. Control of the library was normal as well. This solution is not ideal, however, because I am actively using bandwidth with my computer and cannot afford to be tethered to my 3G connection. A viable solution for me is to use a common VPN connection, which I have set up on a Ubuntu (Intrepid) server that is remote. Both my computer and iPhone are able to access the VPN via PPTP. The server is setup with PPTPD as the VPN-server; I'm using IPTables to perform IP masquerading and forwarding traffic. I however, still cannot connect the library to the phone. I can however, see both devices on the VPN subnet (192.168.0.0/24). SSH'ing and such works fine. What settings on the VPN server must I change to get this to work? Also, how can I assign static IP addresses to various PPTP clients based on MAC addresses?

  Read the article

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• How to deal with DELL support system?

  - by Nishant Kumar

  We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). It is Dell India Support System. So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

  Read the article

• Chroot jail of Nginx and php

  - by sqren

  I'm hosting multiple websites on one VPS, and want to chroot each website, eg. /chroot/website1 /chroot/website2 I'm using makejail, which is a highlevel tool, for creating the jails, and copying the libraries and dependencies. Easy peasy. Each website will need nginx, php and mysql. For php I'm using php5-fpm which actually supports chroot by configuration, however I'm not using this (maybe I should?) My question is which approach of the following three is the better: 1) Every website will have its own seperated instance of nginx, php and mysql. The downside is, that each webserver + php has to listen to a different port. I also need a "master" nginx web server in front of them, reverse proxying to the chrooted servers behind it. Probably most secure, but also most advanced. 2) I don't make any chroot jails manually. I setup one nginx web server, that proxies php requests to php-fpm, on different ports. I can have multiple php-fpm configurations each with is own chroot'ed folder. This is quite managable - however only php will be chrooted. Not the actual webserver. Is this secure enough. Also, I tried this option out, and it seems I will need to use TCP instead of sockets for connecting to MySQL. 3) You tell me ;) I'm quite new to chroot jailing, so please correct me if I'm wrong in my assumptions. I've been reading all the tutorials I could find, however, I find the market for chroot guides very scarce. Any help or inputs much appreciated!

  Read the article

• Rsync Push files from linux to windoes. ssh issue - connection refused

  - by piyush c

  For some reason I want to run a script to move files from Linux machine to Windows. I have installed cwRsync on my windows machine and able to connect to linux machine. When i execute following command: rsync -e "ssh -l "piyush"" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" Where 10.0.0.60 is my widows machine and I am running above command on Linux - CentOS 5.5. After running command I get following error message: ssh: connect to host 10.0.0.60 port 22: Connection refused rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(463) [sender=2.6.8] [root@localhost sync]# ssh [email protected] ssh: connect to host 10.0.0.60 port 22: Connection refused I have modified my firewall settings on widows to allow all ports. I think this issue is due to SSH Daemon not present on my windows machine. So I tried installing OpenSSH on my machine and running ssh-agent but didn't helped. I tried similar command to run on my widows machine to pull files from Linux and its working fine. For some reason I want command for Linux machine so that I can embed it in a shell script. Can you suggest me if I am missing anything. I am already having cwRsync installed on my widows and running it in daemon mode using --damemon option. And I am able to login using ssh from windows machine to linux machine. When I issue bellow command, it just blocks for 120 seconds (timeout I specified in command) and exits saying there is timeout. rsync -e "ssh -l piyush" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" After starting rsync on widows, I checked, rsyc is running. And widows firewall setting are set to minimal, and on Linux machine stopped iptables service so that port 873 (default rsync port) is not blocked. What can be the possible reason that Linux machine is not able to connect to rsync-daemon on windows machine?

  Read the article

• How can I add a wireless router to a wired router?

  - by Tester101

  The Setup: wired D-link (EBR-2310) router connected to my cable modem. Wireless NetGear N300 (WNR2000v3) router connected to a LAN port on the wired router. What I'm trying to do: I'm trying to setup the wireless router to be a separate network, that only accesses the internet through the wired router. What I've done so far. I setup the wireless router's WAN port to get an address from ISP (which should be coming from my wired router running DHCP), and the LAN as a subnet (192.168.1). Wired router's LAN is 192.168.0. The problem: I'm not able to connect to the internet from the wireless router. At one point my wired router showed that it was handing out an IP to the wireless router, but that is not happening anymore. The question: Is what I'm trying to do possible? Am I not thinking about this properly? Do I need to buy a better wired router, with 2 WAN ports? How can I configure these routers to work together?

  Read the article

• Ntop monitoring - Hosts visible with no SPAN/mirroring

  - by Cory J

  I am attempting to use ntop to monitor traffic over a Cisco Catalyst switch. I was assuming that in order to see any of the traffic, I'd have to use monitor, as described here: http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015c612.shtml. Howver, before I did anything on the switch, I simply plugged my ntop server in and fired up ntop. To my suprise, I instantly see 3+ pages of hosts, and thousands of packets. How is ntop seeing this? I have verified that no monitoring exists on the switch (run as en): cs1.pvdc#show monitor No SPAN configuration is present in the system. My ntop server is Ubuntu 8.04, I haven't done ANY configuration, I just installed the ntop package. This is also a fresh Ubuntu install. Is there anything else on my switch besides "monitor" that might cause my switch to mirror all its traffic like this? I've tried plugging ntop into different ports with the same results. UPDATE: It appears to be more then just broadcast traffic showing up in ntop, for example, I can see when my IPs have talked to the DNS server or generated HTTP traffic. If my switch is misconfigured, can anyone point me in the right direction towards rectify this? Not a Cisco expert.

  Read the article

• VPN Device behind router/firewall

  - by David Steven

  ROUTER A: Peplink 310 serving as the gateway/router/firewall at one location. ROUTER B: Linksys RV082 serving as the gateway/router/firewall at another location. I want to VPN these two locations together. The Peplink has a PPTP server and has proprietary site-to-site vpn if you had another peplink device. The Linksys has an IPsec vpn server. VPN A: I also have another spare linksys rv082. I'm trying to setup the other rv082 (VPN A) behind the peplink (ROUTER A) and get VPN A to talk to ROUTER B. I setup VPN A with a lan ip address and plugged one of it's LAN ports into the LAN. I was able to get to it's web interface fine. On ROUTER A I one-to-one nat mapped one of our public ip's to the LAN IP for VPN A. I opened TCP 50-51 and UDP 500 to VPN A. I configured the VPN settings on VPN A to connect to ROUTER B. I did the opposite for ROUTER B. But the vpn doesn't connect. Then I tried pluging VPN A's wan port into the lan, and gave it another LAN IP. I thought perpahs VPN A didn't want to send VPN traffic out over the LAN and wanted do send it over it's WAN. The vpn still doesn't connect. It what I'm trying to do even possible?

  Read the article

• VLAN with trunk to avoid broadcast storm in a network with redundant paths

  - by liv2hak

  I have 6 Juniper switches (EX - 2200) connected to each other as shown in the network topology. I have two PC's that I am using PC1 - (used for configuring the 6 switches via minicom) PC2 - to monitor the traffic between the switches via the Ports that are marked with arrows in the diagram. STEP 1: I create a new vlan On Switch 3 (SW3) that includes Port 12 and Port 22. I also assign l3-interface to the vlan (vlan_2) with ip address - 192.168.1.7. Now I plug-in Port 0 of Switch 3 on PC2. Now I try pinging 192.168.1.7 from PC2 (192.168.1.10) I want to know what will happen? My postulation is that I will not be able to ping SW3 from PC2.This is because SW3 (Port 12 and Port 22) is a part of a vlan_2 and vlan_2 logically breaks up broadcast domains and so 192.168.1.7 will not be reachable from 192.168.1.10. Now I have an l3-interface on SW1 with IP 192.168.1.1 using default vlan( vlan-id 0). Similarly I have enabled IP on SW2 - 192.168.1.2 SW3 - 192.168.1.3 SW4 - 192.168.1.4 SW5 - 192.168.1.5 SW6 - 192.168.1.6 all using default vlan. I create VLAN2 with the following configuration SW3 - Port 12,Port 22. SW6 - Port 14 I create VLAN3 with the following configuration SW3 - Port 0 SW6 - Port 0 I also configure a VLAN trunk between SW3 and SW6 using the following commands. edit interfaces ge-0/0/12 set unit 0 family ethernet-switching port-mode trunk edit interfaces ge-0/0/12 set unit 0 family ethernet-switching vlan members all There is a redundant path in the network as the loop between SW3 and SW6 is closed.There is no broadcast storm in the network? What is the reason for this? I have not enabled STP or RSTP.still there is no broadcast storm.what is the reason for this. (Please ignore the CISCO symbol on the switches in the diagram.All swithes are Junper EX 22-00.)

  Read the article

• KVM Guest with NAT + Bridged networking

  - by Daniel

  I currently have a few KVM Guests on a dedicated server with bridged networking (this works) and i can successfully ping the outside ips i assign via ifconfig (in the guest). However, due to the fact i only have 5 public ipv4 ip addresses, i would like to port forward services like so: hostip:port - kvm_guest:port UPDATE I found out KVM comes with a "default" NAT interface, so added the virtual NIC to the Guest virsh configuration then configured it in the Guest, it has the ip address: 192.168.122.112 I can successfully ping 192.168.122.112 and access all ports on 192.168.122.112 from the KVM Host, so i tried to port forward like so: iptables -t nat -I PREROUTING -p tcp --dport 5222 -j DNAT --to-destination 192.168.122.112:2521 iptables -I FORWARD -m state -d 192.168.122.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT telnet KVM_HOST_IP 5222 just hangs on "trying" telnet 192.168.122.112 2521 works [root@node1 ~]# tcpdump port 5222 tcpdump: WARNING: eth0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:43:47.216181 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445777813 ecr 0,sackOK,eol], length 0 23:43:48.315747 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445778912 ecr 0,sackOK,eol], length 0 23:43:49.415606 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445780010 ecr 0,sackOK,eol], length 0 7 packets received by filter 0 packets dropped by kernel [root@node1 ~]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state NEW,RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination All help is appreciated. Thanks.

  Read the article

• How to multiseat with HW 3d accel on CentOS 6.3 Final?

  - by user35070

  I would like to setup a multiseat configuration on CentOS 6.3 (two video cards, two keyboards, two mice, two monitors) and have hardware accelerated 3D on both monitors. 3D HW acceleration rules out Xephyr. I saw somewhere that recent versions of GDM (3.3 and newer?) don't support multiseat, so do I have to install KDM to make this work? If I just create a duplicate section with new device identifiers in my xorg.conf file, will this 'just work'? Using different ports on the same video card and separate keyboards, mice, and displays, the result was a desktop which spanned both monitors with both keyboards and mice acting as the same input in the GUI. I will power down and put in the new video card and report on the results soon. Both video cards are nvidia. UPDATE after putting in another NVIDIA video card, default behavior (before changing xorg.conf) is that one screen works normally, and both mice and keyboards are connected to it. Changing xorg.conf and the display manager to KDM and following the directions here https://help.ubuntu.com/community/MultiseatX#Ubuntu_10.04_.28Lucid.29 , I have 2 mirrored screens connected to separate video cards, DRI enabled, and 2 mice both connected to the same pointer. Keyboards don't do anything, however, I probably just need to fix a setting in xorg.conf I would still like to get multiseat functionality, eg. separate screens with separate input devices I have verified that the separate X processes are running (see page above) using 'ps aux | grepX [01]'

  Read the article

• Can I attach a VPN firewall to an existing network and have it manage VPN connections?

  - by jules

  I'm quite new to networking and am trying to set up my first VPN connection. The Situation: I have been contracted for some programming at a facility some distance from my location. I would like to be able to set up a simple VPN connection to their network so that I may make adjustments without significant travel. Their Current Network: Six devices (one I need to connect to) plugged into a basic router (Dlink). This router has an internet connection and a static ip address. My Hopeful (questionable) Proposal: I attach a VPN Firewall I happen to own (Netgear FVS318) as device number seven on the client network. I disable routing / DHCP in the Netgear. I forward the appropriate IPSec ports from the Dlink to the Netgear. I then create a VPN connection on my office Windows 7 machine to the remote network. The request is forwarded from the Dlink to the Netgear where the VPN connection is authenticated. I now have a remote-access connection from my office PC to the client's local network. The Question: Will this proposal work? If not, would another possibility be to attach a computer with a VPN server to the client network? Also, as a note: the client has requested I not replace their router or place mine in-between theirs and the internet :( Thanks very much!

  Read the article

• Monitor connected with WiDi just shows a black screen

  - by Pops

  I have a Dell XPS 18 and want to use an external monitor with it. The monitor has VGA and DVI-D inputs. The XPS 18 has no video output ports, but it does support Intel WiDi. I have a Netgear P2TV2000 WiDi receiver, but it only has composite and HDMI outputs. I'm connecting the receiver to the monitor with an HDMI cable and an HDMI/DVI-D adapter. So, in short, the video path is: Computer → WiDi → WiDi receiver → HDMI cable → HDMI/DVI-D adapter → Monitor After setting all this up, I can't get anything to display on the monitor. At the moment I power the monitor on, I can see my desktop for a brief fraction of a second, and then everything goes black. All of the relevant drivers have been updated to the latest versions. When I use a different WiDi-enabled computer to connect to the same monitor, everything works fine. When I use the original computer and receiver to connect to a TV, everything works fine. It's only when I connect the original computer to the monitor I want to use that the connection fails. What could be going wrong here, and how can I get the video to work consistently?

  Read the article

• HP c6180 driver refuses to install - "must reboot to continue delete files and continue install" loo

  - by Aszurom

  User called me last night, can't get HP drivers to install for printer. 500 meg download for latest c6180 driver. PC says "computer must be restarted to delete some files, then setup will continue." and it won't pass that point. (that's not exact phrasing of the error, and I'm not on the system now) Target machine is XP SP2. I upgraded to SP3. Fully patched. Ran malwarebytes, spybot, hijack this and turned off all startup entries. I noted that windows update also failed on optional printer driver updates for other printers installed on the machine. Went to printer server properties, removed all print drivers from system, deleted all printer ports. Made sure no services were marked disabled. After 5 hours of fighting this I started to get desperate, and uninstalled anything that referenced HP in the machine at all. Still no cure. I'm 6 hours into this and completely stumped. Google returns nothing applicable except unanswered requests for help on same topic.

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• Process killing trouble

  - by Aditya Singh

  I am trying to program a server software which involves a lot of testing on java / scala platform. Whenever i compile and execute the code. It starts listening on port 80. Sometimes i need to terminate it by Ctrl+C when it hangs. In that case, ubuntu is not freeing the port. So in order to run the process, i have to restart the machine. I see this at ps aux root 1924 0.0 0.0 5796 1660 pts/0 T 05:44 0:00 sudo scala - root 1925 0.2 1.5 491448 40796 pts/0 Tl 05:44 0:03 java -Xmx256M -Xms16M So process 1924 and 1925. I did sudo kill on both these. But then they keep on persisting even after a long time. sudo nmap -T Aggressive -A -v 127.0.0.1 -p 1-65000 Scanning localhost (127.0.0.1) [65000 ports] Discovered open port 80/tcp on 127.0.0.1 It means its still there ! sudo netstat --tcp --udp --listening --program tcp6 0 0 [::]:www [::]:* LISTEN 1925/java tcp6 0 0 ip6-localhost:ipp [::]:* LISTEN 1185/cupsd This means its 1925 - java How to kill it.

  Read the article

• Error applying iptables rules using iptables-restore

  - by John Franic

  Hi I'm using Ubuntu 9.04 on a VPS. I'm getting an error if I apply a iptables rule. Here is what I have done. 1.Saved the existing rules iptables-save /etc/iptables.up.rules Created iptables.test.rules and add some rules to it nano /etc/iptables.test.rulesnano /etc/iptables.test.rules This is the rules I added *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22- j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT After editing when I try to apply the rules by iptables-restore < /etc/iptables.test.rules I get the following error iptables-restore: line 42 failed Line 42 is COMMIT and I comment that out I get iptables-restore: COMMIT expected at line 43 I'm not sure what is the problem, it is expecting COMMIT but if COMMIT is there it's giving error. Could it be due to the fact i'm usin a VPS?My provider using OpenVZ for virtualizaton.

  Read the article

• Attempts at NIC teaming on Server 2008 R2 with PRO/1000 MT

  - by Klaus

  I have a Dell PowerEdge 1850 server and a gigabit switch that supports nic teaming (and was configured to do so). The server has a total of four Intel PRO/1000 MT ports, which also support teaming. But.. for some reason Intel does not actually have a version of the drivers/ProSet that will work for these cards on 2008 R2. You have to use the built-in drivers that come with 2008 R2, which do not support the additional features. According to their website, they have no plans to change this. Strangely enough, I experimented with various drivers in an attempt to force it to work. At one point, the teaming was working, but there were side effects (such as the DNS server refusing to start). So now I am back to running just one of the cards, (very) frustrated about the whole situation. I have looked all over to see if there is some way around this, but have not had any success. I know I can probably just get a new network adapter for it, but with the good deal I got, that would cost more than the server! :) While staying with 2008 R2, does anyone know of any possible alternatives? Thanks!

  Read the article

• Increasing SQL Server / Sage performance with SSD? (Dell PE T410)

  - by Anthony

  I have a client wanting better performance of their Sage (Accpac & CRM) server (v5.5, soon to be v7). It's running on 1 of 2 Hyper-V VMs (Svr2008) on a Dell PE T410 server with 24GB of RAM (1333MHz) & dual quad-core, and both VMs (only their C: drives) are on a single RAID5 array. All clients connect via 1Gb ethernet. The 2nd VM is SBS2008 with 9GB RAM (& all SBS dbs & company data are on a separate RAID5 array), & 3GB RAM for the Svr2008 hypervisor. I've given the Sage/SQL Server VM all the RAM I can (12GB) & SQL Server RAM caching (~8GB, never exceeds ~7.5GB, eg. entire db can now be cached in RAM) and that's helped significantly. Upgrading the Hypervisor to Svr2012 is an obvious step, but probably not a dramatic improvement? What about an SSD for this Sage/SQL Server VM (VM = 100GB, <10GB for the actual live DB) ? Can SSDs be put into the SAS hot-swap bays? Or will I have to use the mobo SATA(3Gbps?) ports, or PCI-E SSD card? Should SSDs be RAIDed for this situation? Or is SSD's higher reliability offsetting the need for RAID1/5/10? (I have nightly full disk backups) New territory for me, would appreciate some feedback. Thanks, Anthony.

  Read the article

• Unable to connect remotely to Vsftpd server set up on CentOS VirtualBox

  - by ryekayo

  I have set up a Vsftp server using the following instructions provided Here and even went as far as following the commentary at the bottom. But I am unable to connect remotely. When I attempt to use FileZilla or my Ubuntu terminal, I always get: ryan@ryan-Galago-UltraPro:~$ ftp 10.0.x.xx ftp: connect: Connection timed out ftp> I have checked and re-checked iptables conf file and made sure that Port 21 is being Accepted and it is. I have looked this up on the web and decided to try nmap to port scan it and this is what I get for a result: ryan@ryan-Galago-UltraPro:~$ nmap -PN 10.0.xx.xx Starting Nmap 6.40 ( http://nmap.org ) at 2014-08-19 15:01 EDT Nmap scan report for 10.0.xx.xx Host is up. All 1000 scanned ports on 10.0.xx.xx are filtered Nmap done: 1 IP address (1 host up) scanned in 201.38 seconds Is there anything else that I should do or check for? UPDATE: I have tried to ping from the virtual machine to my IP address on Ubuntu and have been successfully able to. I cannot ping to my virtual machine from Ubuntu. I have narrowed this down to possibly being a firewall related issue on Ubuntu's side, but why would I be unable to connect from FileZilla?

  Read the article

• Increasing MSSQL/Sage performance with SSD? (Dell PE T410)

  - by Anthony

  I have a client wanting better performance of their Sage (Accpac & CRM) server (v5.5, soon to be v7). It's running on 1 of 2 Hyper-V VMs (Svr2008) on a Dell PE T410 server with 24GB of RAM (1333MHz) & dual quad-core, and both VMs (only their C: drives) are on a single RAID5 array. All clients connect via 1Gb ethernet. The 2nd VM is SBS2008 with 9GB RAM (& all SBS dbs & company data are on a separate RAID5 array), & 3GB RAM for the Svr2008 hypervisor. I've given the Sage/MSSQL VM all the RAM I can (12GB) & SQL RAM caching (~8GB, never exceeds ~7.5GB, eg. entire db can now be cached in RAM) and that's helped significantly. Upgrading the Hypervisor to Svr2012 is an obvious step, but probably not a dramatic improvement? What about an SSD for this Sage/SQL VM (VM = 100GB, <10GB for the actual live DB) ? Can SSDs be put into the SAS hot-swap bays? Or will I have to use the mobo SATA(3Gbps?) ports, or PCI-E SSD card? Should SSDs be RAIDed for this situation? Or is SSD's higher reliability offsetting the need for RAID1/5/10? (I have nightly full disk backups) New territory for me, would appreciate some feedback. Thanks, Anthony.

  Read the article

• Mac Port error installing gsoap

  - by Kevin

  Hi All, I have installed Mac Ports V1.8.1 no worries. I ran sudo port -v selfupdate no worries. I ran sudo port install gsoap And get the following error message. --- Computing dependencies for gsoap --- Fetching gsoap --- Attempting to fetch gsoap_2.7.13.tar.gz from http://optusnet.dl.sourceforge.net/gsoap2 --- Verifying checksum(s) for gsoap --- Extracting gsoap --- Applying patches to gsoap --- Configuring gsoap Error: Target org.macports.configure returned: configure failure: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_devel_gsoap/work/gsoap-2.7" && ./configure --prefix=/opt/local --enable-samples " returned error 77 Command output: checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... no checking for mawk... no checking for nawk... no checking for awk... awk checking whether make sets $(MAKE)... no checking build system type... i386-apple-darwin10.2.0 checking host system type... i386-apple-darwin10.2.0 checking whether make sets $(MAKE)... (cached) no checking for C++ compiler default output file name... configure: error: C++ compiler cannot create executables See `config.log' for more details. Error: Status 1 encountered during processing. Any ideas as to why it is failing. Regards Kevin

  Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >