Search Results

Search found 4141 results on 166 pages for 'router'.

Page 133/166 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Is 50% download speed on a wireless G network normal?

  - by Bartlomiej Skwira

  I have a wired connection of about 36Mb/s, but my wireless speed is max at about 18-19Mb/s. I have a WRT54G-TM (T-Mobile, 802.11G) router with DD-WRT firmware - I've upgraded it to latest build. Done some settings changes: changed channel - 13 wireless network mode - G-only ACK Timing - 0 Fragmentation Threshold and RTS Threshold - 2304 Basic Rate - All Signal/Noise ratio: -46/-94, signal quality ~50-60%. Is this normal with G networks? Edit: The AP is located about 2 meters from laptop, no walls or metal objects, but its next to a TV. I've done a channel scan (had problems locating it, go to "Status - Wireless - Site survey" - lame naming) and everybody else is on channels 1 and 6. Switched to channel 11 but it didn't help. As for trasmit power I got best results with default 71mw. The antenna might be a factor, I'm using the default 2 antennas.

  Read the article

• How to configure OpenVPN server to use custom default gateway?

  - by Arenim

  I have a vpn server at address 10.1.0.2 and the server have another ip in it's network -- 10.0.0.2 in his subnet (it's a tun2socks router). But default server's gateway is NOT 10.0.0.2 (and it's ok) but another external IP. I want all the client's traffic to be forwarded through this ip address -- 10.0.0.2. Here is part of my server's config: dev tap0 server-bridge 10.1.0.1 255.255.255.0 10.1.0.50 10.1.0.100 push "route 10.0.0.0 255.255.255.0" ; now client can ping 10.0.0.2 push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 10.1.0.1" push "dhcp-option WINS 10.1.0.1" in fact i want some like push "redirect-gateway 10.0.0.2" How can I achieve this?

  Read the article

• Problems with connecting to wireless network on windows 7

  - by Naveen

  I have a Dell laptop with Windows 7 (Home premium) 64 bit edition installed on it. I use a Wi-Fi router to browse the net. My problem is, I lose the network connection every 10 minutes or so. The network icon on the system tray shows the refresh icon and the status as "identifying network". The network is fine and works fine with my phone. I saw on the net this may be caused if I have enabled IPv6, so I disabled it but still problem persists. When I look at the event log I see the following entries: "Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0xXXXXXXXX. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server." I have also installed VirtualBox(32 bit edition) on the laptop. Does anybody any solution to this?

  Read the article

• DNS for route between WAN & LAN

  - by David Maitland

  I have a few machines set up on my internal 192.168.1.* network and i have one public ip, my router is links all ports to on internal linux machine on my network 192.168.1.3. I want to know how to configure the DNS server on my linux box to forward to internal LAN ip's depending on the host name. EG. computer4.83.22.56.12 would find my box then forward to 192.168.1.4 on the local network. This is so i can run multiple web server under one ip. btw, i use Ubuntu. Thanks Dave

  Read the article

• Firewall is blocking internet traffic to OpenVPN clients

  - by user268905

  I have a virtual network setup with a Linux router/firewall connected to two private networks. An OpenVPN server in routing mode and a web server are in one of the networks. On the other are linux client machines which access the webserver and the Internet through the OpenVPN server. Also, external clients can access the OpenVPN from the Internet. The OpenVPN's server.conf is setup to use routing mode in udp, push DNS and routes to the network it is in so clients can access the webserver. Here are my very strict firewall rules. After connecting to the OpenVPN server, my clients can not access the Internet or the web server. When I allow FORWARD traffic to go through, it works just fine. The OpenVPN server has full internet connectivity. What firewall rule do I need to add to allow internet traffic to reach my clients?

  Read the article

• Ultimate way to use Picasa in a home network

  - by luisfarzati

  I've been trying a lot of approaches but still didn't find any effective solution. I want gigs of photos in a network drive (a IOMega Home Media Network Drive, plugged to my wifi router). I'd like to do 2 things: Do a Picasa import process of all the photos in the drive, making Picasa organize all the files in a year/month folder structure physically. Ideally, the import target directory should be the same network drive, otherwise I should move all the imported files in my local computer back to the drive myself. Share the Picasa database over the network, by uploading it to the network drive. Have me and other members of the family point our Picasas to the network database, and see the photos as well as make changes (tag faces, create logical albums, etc) into it. Is ANY possibility to accomplish this? Or should I be looking for another photo management app, and in that case do you know such one? Thank you!

  Read the article

• Get OpenVPN clients names to resolve through dnsmasq

  - by Fake Name

  I have a PFSense box running as an OpenVPN server. There are several remote devices that connect through the VPN (as tap devices). The VPN stuff is working, I can access the remote hardware by looking up the IP assigned to each device on the PFSense router. What I'd like is to have it so I can resolve the remote hardware addresses via DNS while on the local network. Note that this is only local-network - remote-device (they're backup boxes). I don't need to have the remote devices resolve using the local DNS forwarding agent. I have the rest of the devices on the network that need to be accessible via DNS report their name during the DHCP process. However, the IP assignment for OpenVPN tap clients, while it is dynamic (which is why I need DNS), does not seem to use the local DHCP server. How can I have my openvpn server add information for it's clients to the dnsmask resolver? Is this setup even reasonable (I'm not familiar with openVPN at all)?

  Read the article

• Windows 7 - saved wifi access points disappear from list

  - by KáGé

  I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

  Read the article

• How to collect figures of traffic used per-host, broken up by time and destination?

  - by Seishun

  We have a relatively small network, all PSs in one subnet. One PC with two NICs and pfSense installed works as a firewall/router. There is an OpenVPN tunnel to a remote location, created as a site-to-site connection to another pfSense box there. I have an assignment to capture, store and show (via a web interface) information on traffic generated (both incoming and outcoming) by each host on our subnet and present it in several views: megabytes per calendar hours / days / months / years (that is, not just "one month back", but "in Dec 2010" and so on); megabytes per destination: VPN to remote location / other destinations / Google Apps servers. I tried the software packages in pfSense that offer traffic montoring - but it seems they don't store the information fixed by months, instead showing the amounts of traffic generated in periods (days/months/etc) calculated from the present moment. I'm also interested in understanding what would be the best way for me to break up traffic by hosts and destinations. I'm open to all suggestions, even if they mean that I will have to understand something new to me.

  Read the article

• Wireless option grayed out in Windows Mobility Center

  - by thomasvdb

  We currently have a Lenovo ThinkPad L512 which can't connect to wireless networks. He simply indicates he can't find any networks. Other notebooks (also ThinkPad L512-notebooks) in the company do find the network so nothings wrong with the configuration of the wireless router. As indicated on answer.microsoft.com, I should check Windows Mobility Center and enable the entry "Turn Wireless On". Unfortunately this option has been grayed out. How can I enable this option? There isn't a physical switch on the laptop to turn on the wireless.

  Read the article

• Openvpn client-to-client connection reencrypted at Server?

  - by user1684411

  currently i'm using a site-2-site openvpn setup. The routers en/decrypt all traffic that goes from one net to another. One of them is the Openvpn server. This works but performance is not as good as possible. I think the limiting factor is the cpu power of the router. Would it be better if i use client-to-client connections and access the fileserver in the one net from a pc in the other, because the openvpn-server does not have to decrypt the (whole) packets?

  Read the article

• How to bridge two networks via VPN (IPsec)?

  - by polemon

  I'd like to do a Site-to-Site bridging with VPN (IPsec), how do I do that? On the local side, I have a DrayTec Vigor2910, it is supposed to be able to manage IPsec tunnels. Anyway, I need to have several VPN tunnels to various sites, but how exactly do I do that, If the only router I can configure, is the local one? As I understand it, I'd need some sort of VPN server or client, or whatever on the other side. In any event, please clarify that issue. Thanks.

  Read the article

• Iptables and counters

  - by mehturt

  I'm trying to use iptables counters with munin to monitor traffic of hosts on my local subnet. For each host I set up a rule like this: iptables -I OUTPUT -d $ip This should count the packets going from firewall to $ip, correct? I found out that this does not seem to count all packets. I start tcpdump on my router (Linux) and I see packets to $ip that are not counted. For example I check number of packets for rule to my phone IP. I start tcpdump, refresh Gmail on my phoone, I see packets in tcpdump's output but iptables rule counters are not incremented. Then I open a web page on the same phone and the counters are incremented. What could be the reason?

  Read the article

• node.js server not running

  - by CMDadabo

  I am trying to learn node.js, but I'm having trouble getting the simple server to run on localhost:8888. Here is the code for server.js: var http = require("http"); http.createServer(function(request, response) { response.writeHead(200, {"Content-Type": "text/plain"}); response.write("Hello World"); response.end(); }).listen(8888); server.js runs without errors, and trying netstat -an | grep 8888 from terminal returns tcp4 0 0 *.8888 *.* LISTEN However, when I go to localhost:8888 in a browser, it says that it cannot be found. I've looked at all the related questions, and nothing has worked so far. I've tried different ports, etc. I know that my router blocks incoming traffic on port 8888, but shouldn't that not matter if I'm trying to access it locally? I've run tomcat servers on this port before, for example. Thanks so much for your help! node.js version: v0.6.15 OS: Mac OS 10.6.8

  Read the article

• Linux QoS (Skype / BitTorent / SIP / HTTP priority)

  - by Andre

  We are configuring a linux box that will act as internet gateway for an office of 30-50 computers. We are using iptables/HTB for traffic shaping. Is there a way to match traffic on L7 level? It's easy to identify traffic by TCP/UDP ports (like SIP and HTTP). But what if we are dealing with Skype & BitTorent? It was surprise for me that there is no powerful and matured sulution for tasks like this. I found only l7-filter (http://l7-filter.clearfoundation.com/) patch for the Linux kernel, but it's no longer supported (it seems to). Moreover it couldn't be compiled with modern Linux kernels. The only option I found was to use a Cisco router. Are there other ways to identify and shape Skype and Bittorent traffic?

  Read the article

• Share the DVB card on windows 7 [closed]

  - by Bashar Kernel

  I have 2 computers connected to a router and I have a DVB card in one of them. I want to use the one DVB card to feed both of them. I read about it and I know that I want to share the DVB adapter with the Internet Connection Sharing on the LAN network. But when I use the connection sharing, I lose my internet access I tried to use "Bridge Connection", but then I also lost my internet access too. Can any one tell me how to fix this problem? And how to view the channels (for example how to use the VLC)?

  Read the article

• Why can't I access the WebUI of my DNS-323 NAS after a firmware upgrade?

  - by anonymous2

  Hi Everyone, I just bought a D-Link DNS-323 NAS Enclosure, and have run into a problem. I read that the firmware that had shipped with (1.07) did not support 2TB drives, so I downloaded firmware 1.08. Turned on the device for thwe first time and went straight to the WebUI (everything looked/worked fine) Proceeded with the firmware update, completed successfully. Rebooted and I cannot access the WebUI. I can see the NAS connected via my router interface I can also ping the ip adress assigned, but I cannot access the WebUI or find it via D-Link easy search software. I have tried the factory reset button, but that does not seem to be doing anything, the square blue light just keeps flashing from the moment the unit is powered on, whether I press the reset button or not, and the symptoms remain the same... PS. I did/do not have any drives installed yet. Please help?

  Read the article

• Installing WiFi in a church for internet access

  - by Dave Griffiths

  Hi, a colleague at work asked this question: My local church want to get WiFi enabled in the whole of their offices and main church building. The offices and main building are in the same overall structure and so the signal does not need to travel outside to any other buildings outside this main structure. Where would I start on such a project and what kind of repeaters are needed (and how are they set up) given that some of the walls are pretty thick. Do you still have one ADSL line coming in to router or are there some options of having two lines coming in so that they isn't a single point of failure. Am looking at fibre for the broadband for increased speed. Any starting pointers appreciated.

  Read the article

• Improving sound quality with remote ESD server

  - by cuu508

  Hi, I'm investigating low-budget ways to get audio from my PC (Ubuntu) to HiFi without wires. I'm currently testing a setup where Asus WL-500gP wireless router runs ESD daemon and has attached USB soundcard which is then plugged into HiFi. I'm testing playback on PC with mpg123-esd and Spotify under Wine. The sound is there, latency is unexpectedly low, but I also hear occassional clicks and some distortion from time to time. I suppose that's because of the low latency and wireless streaming of uncompressed audio--any packet drops, CPU temporarily being busy etc. will cause clicks in sound output. Is there a way around this problem, increasing latency / buffer size somehow perhaps? Streaming using shoutcast protocol seems to be a way out but I have feeling that would be a complex and brittle setup.

  Read the article

• cannot using internet in VMWare

  - by user66247

  I am using VMware Workstation version 7 on Ubuntu 10.10. I installed Windows XP service pack 3 for guest os. Within VMWare, I am using bridge connection that I assigned static IP address to be able to ping host IP address but I cannot ping default router gateway. I also tried to command "/etc/init.d/vmware start" on terminal. All tasks are able to start successfully except "VM communication interface socket family" I am not sure that how to setup network for my VMWare by using wireless. Thanks in advance.

  Read the article

• Windows xp media center, iTunes, Home sharing problem with app Remote and Apple tv2

  - by Amador

  Hello everybody, greetings from Mexico, sorry about my english but here it goes: I recently bought and apple tv 2nd generation it works just fine, i can see you tube videos but i cant see my library. My pc is conected to the same wi-fi than my apple tv. I have the latest software. I have my firewall off. I turned off and on my router. Search for iphone, ipad remotes on, sharing my library on my local network on, in itunes. Ive checked that my id was the same. On top of that the Remote app doesnt seem to work either. Please help, im kinda loosing my mind over this

  Read the article

• Unable to open websites that use HTTPS on linux

  - by negai

  I have the following network configuration: My PC 192.168.1.20/24 uses 192.168.1.1/24 as a gateway. Dlink-2760U router with Local address 192.168.1.1/24 has a VPN connection open with the provider using PPTP. Whenever I'm trying to open some web-sites that has some authorization (e.g. gmail.com, coursera.org), I'm getting a request timeout. This problem is observed mostly on linux (Ubuntu 12.04 and Debian 6.0), while most of such websites work correctly on windows XP. Could you please help me diagnose the problem? Could it be related to NAT + HTTPS? Thanks

  Read the article

• How to setup Microsoft Remote Desktop?

  - by jsoldi

  I'm trying to establish a connection between this app and my Win 8.1 Pro PC, but every guide I've found so far skip steps such as what to put under PC name or under Gateway. Also, should the User name be my email or something else? I've also no idea how to find or add a user in the step 6 of this guide because the only location listed is my PC and I don't even know what am I supposed to search for. I'm not even sure whether I have to add a user or this is an step I can skip. A comprehensive guide for people without experience in networking would be highly appreciated. Both my android tablet and PC are connected to the internet through a home router, in case this matters.

  Read the article

• local wordpress installation not accessible from the outside world

  - by hello

  I have a working installation of wordpress located in /var/www/html/wordpress It is accessible in my local network at [local-machine-ip]/wordpress/ There is also a test page located in /var/www/html/test.html It is also accessible in my local network at [local-machine-ip] I would like the wordpress website to be accessible from the outside world. I know that my ISP blocks incoming requests on port 80, so I set my router to redirect requests from port 8080 to 80. This feature appears to be working correctly since I can access the test.html page using my public ip address as follows: [public-ip]:8080 However, I cannot access [public-ip]:8080/wordpress Here is my Apache config : <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/html ServerName [my.domain.com] <Directory /var/www/html/> Options FollowSymLinks Indexes MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Thanks!

  Read the article

• Two VPN connections from the same IP address

  - by Tayles

  I have set up a server running Windows Server 2008 which two remote users can dial into using a VPN connection. It works fine unless they are both in the same location, in which case only one of them can connect. I understand this is because the PPTP protocol cannot cope with two VPN connections from the same IP address. Is this correct? If so, what can I do about it? Please note that the remote location in question is a serviced office, so we're not in a position to change or play around with their router. Thanks!

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >