Search Results

Search found 5864 results on 235 pages for 'secure gateway'.

Page 133/235 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• Set up Windows SBS dns server and vpn clients from brench office

  - by mn

  I have got some clients from bench office which connects vpn to main office. The Router from bench office assigned addresses from DHCP 192.168.1.0/255.255.255.0 and remote gateway assigned vpn ip addresses 10.10.20.0/255.255.255.0. There is a DNS server (Active Directory Win SBS 2000) and vpn client are registered with vpn address (10.10.20.0/255.255.255.0 and domain company.com.pl). I would like to register also primary bench subnet 192.168.1.0/255.255.255.0 with domain for example company.vpn.local I want to access vpn hosts for example: dev3.copmany.pkb.local and dev3.company.com using my Win SBS 2000 DNS server.

  Read the article

• 2wire modem to linksys router

  - by Imajica666

  I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

  Read the article

• Cheapest way to go for somebody who wants to accept payments, but won't be accepting hundreds of ord

  - by blockhead

  I have a client who lectures, and wants to sell spots to his lecture online. I would preferably like to set him up with a solution that allows me to collect billing information on his site. My experience with e-commerce is in using solutions like Authorize.net, however this does not seem cost effective since I can't imagine he's making a huge profit off of this. I'm afraid he would lose money in the cost of using Authorize.net (or any payment gateway for the matter). I could use google checkout or paypal express, but this would require me to leave his site (although with google checkout, it looks like, from a glance, that I could just submit to their form from my server, and likely with paypal as well, but I don't know if this is against their TOS). What is the most cost-effective solution for accepting credit card payments in this situation?

  Read the article

• how to change interface ip in ifconfig with /etc/network/interfaces

  - by user2478348

  Hi everybody when modifiying /etc/network/interfaces, saving it and then executing ifconfig i can't see the modification i made..for example here is part of my /etc/network/interfaces: auto wlan1 iface wlan1 inet static address 192.168.0.60 netmask 255.255.255.0 gateway 192.168.0.61 you can see that the IP address of my wlan1 is 192.168.0.60 but when typing ifconfig i have this: wlan1 Link encap:Ethernet HWaddr 00:19:70:0f:c2:9c inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::219:70ff:fe0f:c29c/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:758 erreurs:0 :0 overruns:0 frame:0 TX packets:610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:73490 (73.4 KB) Octets transmis:127883 (127.8 KB) (the inet adr:192.168.0.1 and not 198.168.0.60)..if someone can help me I'll be very thankful :)

  Read the article

• Waht are the best proxy servers for Mikrotik router?

  - by niren

  I want to setup proxy server for my Mikrotik router. There is inbuilt web-proxy for Mikrotik router but I can extend this upto transparent proxy(kind of proxy server) only. We need High anonymity proxy so that we can hide our LAN static IPs(we don't have private IP) from outside Intruder/hackers. And also I know I can setup NAT rule to hide our IP(only private IP not public/static IP) as per this link, but I cann't hide static/public IP. Essentially I want to hide our Public/Static IP (there is static/public IP for all systems in our company) from outside Internet. To achieve this I guess I need other software apart from Mikrotik router gateway setup. can anyone suggest me Is there any other software to achieve my requirement? I know about squid proxy but am not sure whether It can hide our static/public IP. Note: we have assigned public/Static IP to all systems of our company since we have rights to access our company's system from anywhere by dedicated laptop(given by our company with more security) through VPN connection.

  Read the article

• Tomcat and ASP site under IIS6 with SSL

  - by Rafe

  I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

  Read the article

• Server 2003 RAS Server Utilising High WAN Traffic

  - by Joe Sergeant

  We have Routing and Remote Access configured on Server 2003 (also our primary domain controller), allowing users to connect in remotely to access files, email, etc. With one user, the RAS Server is constantly sending data to that user's remote computer. From 9am this morning it has transferred almost 800MB. The user isn't transferring any files remotely, certainly not enough to total 800MB anyway. None of the other remote users have had this issue. We have ensured that the user in question has "Use default gateway on remote network" disabled for both IPv4 and IPv6 and we are fairly confident that Offline Files isn't trying to synchronise with the server remotely, too. My question is two-fold. Firstly, has anyone had a similar experience? Secondly, what would be the best software to discover exactly what data is being sent to the remote user?

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Windows VPN not authenticating from ADSL to Wireless link

  - by deanvz

  I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

  Read the article

• Is there a sensible way of 'teaming' two ADSL connections?

  - by Tim Long

  I work in an office complex that has two seperate ADSL connections, which they use to provide two seperate networks (actually both the ADSL routers go into a Cisco managed switch with two VLANs, one for each ADSL connection). Circumstances have changed so that 95% of the users are all on one ADSL connection. It would be great if there were a way to join together both connections to emulate a single connection at double the speed, but the ISP doesn't support bonding. So, is there a sensible way to take two completely seperate ADSL lines and use them to provide a single internet gateway?

  Read the article

• dd-wrt switch for PfSense

  - by Kmao

  I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

  Read the article

• ip routes to specific interface

  - by user65053

  I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• 13 IP addresses, how to add them to domain SPF?

  - by Willy

  Hi All, Let say I have these IP addresses on my server: 170.120.210.209 gateway 170.120.210.210 server IP 170.120.210.211 170.120.210.212 170.120.210.213 170.120.210.214 170.120.210.215 170.120.210.216 170.120.210.217 170.120.210.218 170.120.210.219 170.120.210.220 170.120.210.221 170.120.210.222 I am now willing to setup SPF record for my domain but don't want to write each IP one by one. Could you please tell me the short way of this? How can I convert these IP addresses into CIDR notation? Is this correct? 170.120.210.210/28 Thanks for your help.

  Read the article

• Small business VPN solution

  - by Crash893

  I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

  Read the article

• Untangle VPN setup, how to see internal addresses?

  - by NFS user

  So Untangle is setup as the default gateway at 192.168.100.1/24, it is the authorative DHCP server issuing addresses from 192.168.100.100 to 192.168.100.200 and is successfully connected to the Internet. Untangle uses OpenVPN for remote access. Accessing the VPN gives me the address 192.168.40.5. However, I cannot ping any machines on the internal 192.168.100.x network remotely. Clearly, there is something basic that I am missing. What is it and how is it solved? Update: The VPN was not setup with the internal network. Since Untangle only allows editing the VPN setup once, the VPN had to be removed and reinstalled with the internal network exported. Now it works. The lesson is that the internal network must be setup before configuring the VPN.

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• How to limit access to Exchange 2003 Mobile Activesync server by user?

  - by micilin

  So I was asked to set up an Exchange Activesync mobile gateway. That's done. It's a separat eExchange 2003 front-end server configured for SSL, and I've put an off-domain ISA server in front of it. Now I'm being asked to limit which users can connect to it. By default an Exchange front-end server allows any user who has a mail account to connect to the front -end server. So I'm looking at the permissions on the various IIS sites/apps on the server, but I know that it's easy to break Exchange Front-end server perms. So I've got the following in IIS: Exadmin Exchange EchWeb Microsoft-SErver-ActiveSync MobileAdmin OMA And a couple of others that I dont think are relevant. Can I change the permissions on one of these to restrict who can connect to Activesync? As a bonus: Can I do it in a way that does not affect ordinary browser based Exchange Access? Thanks in Advance!!

  Read the article

• IIS FTP service - download timeouts and restarts getting the data twice

  - by accel229

  We have an IIS FTP site on a Windows Server 2003 x64 machine. Application Layer Gateway service is disabled (so http://support.microsoft.com/kb/931130 does not apply). Windows Firewall service is disabled as well. Connection timeout for the FTP site (there is only one) is set to 1,200 seconds = 20 minutes. An external client can connect to the site, list directory contents and download small files. When a client attempts to download a large file (eg, if the download continues for 3 minutes, which is still under 20 minutes, but relatively long), the server sends all data, then the connection times out, the client issues REST / RETR commands attempting to restart the download since after the last byte (which I believe should succeed and receive exactly 0 bytes), and the server behaves as if the client tried to restart after byte 0, that is, it sends the entire file all over. Any ideas on how to fix this?

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• How do I lower idle cpu usage in ubuntu linux? Gnome or KDE Variants

  - by Jasen

  My question comes from a kde desktop currently, but it also happens with the gnome instance. When just sitting there, with only the cpu monitor widget running. no open windows, no background processes other than the desktop, my cpu is at ~20%. I wanna know how to fix this, and possibly get better performance out of it. When running my windows side, the cpu will sit at zero, and i generally load new programs about 400ms faster. With windows 7 being as slow as it is, this is not acceptable. and the widget is only set to check every 500ms, so im almost completely sure its not the widget. My system is a Gateway nv 53 amd 2.0 ghz turion with 4 gb of installed ram, and 500 gb hd. both linux and windows are 64 bit. average ram use on either system is about 1.4 gb for just the os

  Read the article

• Best way to split LAN computers on two WANs (not load balancing)

  - by lpfavreau

  What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

  Read the article

• why this routing configuration does not work?

  - by avs099

  I have 2 VMs in HyperV role: first is RRAS - it has 2 interfaces (both manually configured, no DHCP): 192.168.1.110 - "external" one, connected to the router 192.168.10.2 - that's internal interface which other VMs will be using as well also I added VPN connection to our main server - and it gets 192.168.2.136 IP address in 192.168.2.XXX network. And IP route is create on the server as well for this interface. second VM is called KITCHENER. It only has 1 interface 192.168.10.99 / 255.255.255.0, with default gateway set to RRAS server - 192.168.10.2 QUESTION: how can I ping "main server" - 192.168.2.1 - from the KITCHENER server when RRAS server is connected to VPN? please see screenshots with ipconfig /all, route print and ping 192.168.2.1 commands. What needs to be done to get this working? all servers are Windows 2008 R2 if that matters.

  Read the article

• How to create persistent static route on Mac OS X 10.6?

  - by kopobamypa

  I need to add static route on Mac OS. I found good description here Permanent Static Route Mac OS X 10.4.0 and followed the Roark Holz's (roarkh) solution. Now my problem: sometimes this solution works, sometimes does not. When it doesn't work I see these messages after boot in the Console Messages log: 06.05.10 9:34:13 com.apple.launchd[1] *** launchd[1] has started up. *** 06.05.10 9:34:46 com.apple.SystemStarter[30] Adding Static Route to 10.152 06.05.10 9:34:46 com.apple.SystemStarter[30] route: writing to routing socket: Network is unreachable 06.05.10 9:34:46 com.apple.SystemStarter[30] add net 10.152.0.0: gateway 192.168.1.234: Network is unreachable I want to know what is going on. How this kind of problem can be troubleshooted?

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >