Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 134/343 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

  • VPN Network intermittantly fails to provide internet: What could be possible causes

    - by Jake M
    We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

    Read the article

  • Share the DVB card on windows 7

    - by Bashar Kernel
    I have 2 computers connected to a router and I have a DVB card in one of them. I want to use the one DVB card to feed both of them. I read about it and I know that I want to share the DVB adapter with the Internet Connection Sharing on the LAN network. But when I use the connection sharing, I lose my internet access I tried to use "Bridge Connection", but then I also lost my internet access too. Can any one tell me how to fix this problem? And how to view the channels (for example how to use the VLC)?

    Read the article

  • MikroTik ipv6 Tunnel

    - by MikeSmitty
    I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

    Read the article

  • Finding all domain names that resolve to the same ip?

    - by Janak
    Lately I've been tracking a spammer on craigslist. I recently discovered that he's added a new technique to his arsenal, he registered a whole bunch of domain names but they all resolve to the same ip address. Is there any way to take an ip address and get a list of all the domain names that resolve to that ip?

    Read the article

  • Top ten security tips for non-technical users

    - by Justin
    I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

    Read the article

  • Does HP 8530w support Wifi 802.11n?

    - by FoxyBOA
    According to vendor site HP 8530w supports 802.11n draft mode. My Windows 7 tell me that network card is 5100 ABG and know nothing about N mode (guys from Intel forum mentioned, that 802.11N versions must ended with N letter, e.g. 5100 ABN). Not sure if it matter, but my laptop model id is #FU462EA. How could I check that my Wifi card compliant with 802.11n (I suspect that "draft N" could have two "special" meaning: doesn't work with 802.11n at all or requires special activation of the mode). Any hints are welcome.

    Read the article

  • What keeps you from changing your public IP address and wreak havok?

    - by Whitemage
    An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

    Read the article

  • Windows 7 - Local Area Connection Adapter is disabled

    - by teepusink
    I just got Windows 7. However, I'm now unable to connect to the internet. Doing the diagnosis gives me these: There might be a problem with the driver for the Local Area Connection Adapter The Local Area Connection 2 Adapter is disabled How do I resolve those? These are the things I've tried: In cmd do ipconfig /renew In Device Manager, go to Network Adapter. (I don't see any red exclamation marks)

    Read the article

  • Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

    - by Thomas Chia
    I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

    Read the article

  • Having trouble setting up my router

    - by indyK1ng
    I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • How to Set Linux Bonding Interface to Gigabit

    - by Kyle Brandt
    I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • Configure an Azure VM for Dynamic DNS for Cloud Services

    - by Adam
    I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

    Read the article

  • Wake On Lan for Fedora 12

    - by Toymakerii
    I have a fedora 12 box that I am using as a sandbox for web development and a few other toys. The box gets really hot so I would like it to sleep/hibernate when no one is using it, however most of the people connecting to the box will not be able to access it physically. Is it possible to set up a Wake On Lan that wakes up the machine when it detects an SSH connection? A google search didn't yield much information. (or atleast I wasn't smart enough to register it as useful!)

    Read the article

  • Anytime I upload something, my internet slows down extremely. What can I do?

    - by Earlz
    Title says it all. For a bit more info though: Basically, I have Time Warner cable internet. My speeds maintain a stable 2Mbit/s upload and 20Mbit/s download with average ping times around 30ms. This crazy thing happens though when I upload anything. I went to upload a 200M file to my server today through sftp and my internet completely choked up. I speed tested it during this upload and my ping time was around 800ms, download speeds of 0.2Mbit/s and Upload speeds of 0.3Mbit/s. Note, I wasn't downloading anything during this time either. It is just straight upload. What is it that causes this phenomenon? My router is OpenBSD. Is there anything I could set up to fix this problem(by queues or some such), or is this a problem with cable internet?

    Read the article

  • VMware vSwitches and Dell PowerConnect BPDU guard

    - by dunxd
    I am using two Dell PowerConnect 6248 switches to connect a VMware host vSwitch. A discussion of config of Cisco switches for use with VMware advises to set physical ports connected to vSwitch with bpduguard and portfast. However, Dell switches don't have the bpduguard setting for individual ports. I can switch it off globally for all portfast ports, but I don't think I want to do that. Should I: Disable STP on the vSwitch connected ports? Leave STP on and enable portfast on the ports, and forget about bpduguard? Disable bpduguard on all portfast ports via global config Do something else? See also: VMware vSwitches and spanning tree

    Read the article

  • Network transfer from host to VM very slow - VMWare Server & Windows 2003 Server

    - by barfoon
    Hey everyone, Im trying to transfer a file from a Windows 7 host running VMWare Server to a Windows 2003 server VM, and it's painfully slow. I've tried adding/adjusting registry keys and settings found on KB articles, and still nothing. Ive tried this: http://support.microsoft.com/kb/898468 http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1619 Vmware tools are installed. Any ideas? Thanks,

    Read the article

  • http, https and ftp is not working but smtp and imap is working

    - by Unicron
    hi all, yesterday on a computer of a friend a strange thing happened. after booting the ports fo http, https and ftp are closed but e-mail is still working. in the control panel the windows firewall seems active even if he tries to deactivate it. i have a suspision that it is the faul of norton internet security 2010, we have tried to uninstall it, but the uninstallation did not work. when using the removal tool from symantec it just goes to 23% and then it crashes. the process ccSvcHst.exe is still running. how can i safeley remove the rest of norton internet security? thanks in advance [edit] norton internet security 2010 is sucesfully removed, but still no connectivity

    Read the article

  • SOHO NETGEAR wireless router disconnects when downloading torrents

    - by Lirik
    I have a NETGEAR WGT624 router at home which dies when there is a heavy torrent load. I open up my torrent client and it downloads for about 5 to 10 minutes and it continues to increase the number of seeds (goes up to 70-80 seeds), but after that the router simply fails and I have to restart it in order to get an internet connection again. Is there any way that I can fix this? New router firmware? Change some router options? Feed it a cookie? Anything?

    Read the article

  • What is the equivalent of 127.255.255.255 for OS/X machines so I can test broadcast udp packets without a network?

    - by JohnPristine
    I am trying to test my program that makes use of broadcast UDP (not multicast!). In Linux, I can use the 127.255.255.255:64651 address and everything works beautifully, in other words, I send a packet to 127.255.255.255:64651 and multiple clients listening on that port get the packet. A real broadcast example! Unfortunately on my OS/X machine (Mountain Lion) the same example does not work. Is there any way I can get 127.255.255.255 to work on mac machines? Any other solution to get broadcast working on my mac machine without a network? Note: It has to be broadcast, not multicast.

    Read the article

  • Two identical fiber optic broadband lines working as one

    - by Katafalkas
    I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

    Read the article

  • Can't ping from Win7 running on an MacBook Pro and Can't ping MacBook Pro from any other PC

    - by jorame
    I have Windows 7 Enterprise running on MacBook Pro and for some reason I'm not able to ping any PC in the house from it and the other way around meaning I can't ping the MacBook Pro running Win7 from any other PC. I looked online but I can't find anything that explains this issue or how to resolve it. Any help will be really appreciated. Please do let me know if I'm posting this in the wrong area. Thank you

    Read the article

  • why would you create two different subnets on the same physical network?

    - by xirtyllo
    I'm working at a messy location, one of the strange (for me) things is that on the same physical network there are two different subnets. Specifically some computers will have 10.0.0.0/24 and some others will have 172.16.0.0/24. There is only one DHCP server, which gives IPs on the 10.0.0.0/24 range, and there are two internet gateways, one with IP 172.16.0.1 and one with IP 10.0.0.1 . To give an example, I can easily swap one PC from one subnet to the other just by changing its IP and gateway settings. I am trying to imagine why they created the network this way, and which may be the possible advantages and/or drawbacks of having two different subnets on the same physical network. Any thoughts?

    Read the article

  • Looking for software to create a personal hotspot on Mac OS X (not using the built-in ability)

    - by Fred
    I got my nifty little MacBook Air today. Since I will be going on travel I was hoping to use my iPad 3G as screen extension with Air Display. It works being in a shared WiFi network. Sadly Apple is a bit restrictive on the tethering with their mobile devices such as the iPad. Now I read iOS 4.3 will enable the iPad to use tethered networks. But the feature will not be working for iPad 3G. I assume their big partner telecom companies fear everyone will quit their internet contract with them. So I want to create a personal hotspot on my MacBook and use it on my iPad. But the iPad is not able to use this network. The network is visible but not usable. On Windows there is this connectify program which lets the PC act as wireless router. Does anybody know a similar program for Mac which would turn it into a wireless router? Or is there something I don't see with Mac OS X's builtin features?

    Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >