Search Results

Search found 6301 results on 253 pages for 'dos commands'.

Page 138/253 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• How do I tar dot files but not dot directories

  - by bjackfly

  The following tar command will exclude all dot files and dot directories. tar -cvzf /media/bjackfly/bkup/bkup.gz --exclude '.*' --one-file-system /home/bjackfly In my case I want the dot files to be backed up in the home directory (.vimrc, .bashrc) etc. but not the dot directories /.config /.cache /.eclipse etc. Any Linux gurus with a command for this, or do I need to run a find into a tar or do two different tar commands which is non-ideal? One for dot files in the home directory and one for everything else?

  Read the article

• Manage MS SQL server over SSH (putty)

  - by adopilot

  There is great implementation of PuttY for Symbian S60 devices, and last versions of Nokia phones with full QWERTY keyboard offers comfort for using Putty and SSH goodies. I start wondering is there a way to access MSSQL over SSH and send T-SQL commands. I am able to connect my router which running on FreeBSD OS, also other CentOS server with MYSQL are able to me over SSH. I want to try access MS-SQL-2005 from my mobile phone, Probably this is not going to have daily use, it is just for geeky and justification to myself: why I had to buy so expensive a toy

  Read the article

• I am under DDoS. What can I do?

  - by Falcon Momot

  This is a Canonical Question about DoS and DDoS mitigation. I found a massive traffic spike on a website that I host today; I am getting thousands of connections a second and I see I'm using all 100Mbps of my available bandwidth. Nobody can access my site because all the requests time out, and I can't even log into the server because SSH times out too! This has happened a couple times before, and each time it's lasted a couple hours and gone away on its own. Occasionally, my website has another distinct but related problem: my server's load average (which is usually around .25) rockets up to 20 or more and nobody can access my site just the same as the other case. It also goes away after a few hours. Restarting my server doesn't help; what can I do to make my site accessible again, and what is happening? Relatedly, I found once that for a day or two, every time I started my service, it got a connection from a particular IP address and then crashed. As soon as I started it up again, this happened again and it crashed again. How is that similar, and what can I do about it?

  Read the article

• Custom prompt doesn't work on Mac's terminal

  - by mareks

  I like to use a custom prompt (current path in blue) on my unix machine: export PS1='\[\e[0;34m\]\w \$\[\e[m\] ' But when I try to use it on Mac's terminal it doesn't work: it fails to detect the end of the prompt and overwrites the prompt when I type commands. This also happens when I'm inputting a long command where it wraps over the same line instead of starting a new line. I don't understand why this is the case since I use bash on both machines. Any suggestions on how to remedy this?

  Read the article

• HP ProCurve Port Mode Configuration Question Mark 2

  - by SvrGuy

  We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. From the CLI when I try to set 1000-full I get the following error: Value 1000-full is not applicable to port 39 (or whatever port I try) The exact commands I have entered are: config interface 39 speed-duplex 1000-full BTW: speed-duplex auto-1000 works ( I also tried full-1000 and that did not work either) How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

  Read the article

• How to query Oracle from SQL Server ?

  - by Albert Widjaja

  Hi Everyone, I'm having difficulties in creating a connection from my SQL Server 2008 Enterprise SP2 x64 into the Oracle database 10g even though I have already install the Oracle Client 11g R2 ? I've followed this article from steps URL: http://www.ideaexcursion.com/2009/01/05/connecting-to-oracle-from-sql-server/ plus added: TNS_ADMIN into the Server variables which point into: C:\Oracle\product\11.2.0\client_1\network\admin what is working now: TNSNAMES.ORA has been copied successfully from the other Developer wworkstation i can TNSPING into the DB instance i can connect to the database using SQLplus and perform any SQL commands i can create the DSN ONLY when using "[b]C:\Windows\SysWOW64\odbcad32.exe[/b]" the normal odbcad32 doesn't show my DSN that I have just created ? the DSN created from the above works fine from the test connection. my goal: To be able to select the Oracle connection in the Linked server object but still no effect after I restart the server. (Windows Server 2008 Enterprise 64 bit SP2). Any idea please in resolving this problem would be greatly appreciated. Thanks.

  Read the article

• Windows Handling Piped Comands Error Redirection

  - by jpmartins

  Warning: I am no expert on building scripts, and sorry for lousy English. In an case of generating a CSV from a database query I'm using the following commands. ... CALL java.exe -classpath ... com.xigole.util.sql.Jisql -user dmfodbc -pf pwd.file -driver com.sybase.jdbc3.jdbc.SybDriver -cstring %constr% -c ; -input 42.sql -formatter csv -delimiter ; 2%LOGFILE% | CALL grep -v -e "SELECT right" -e "executing: " -e " rows affect" %FicheiroR% 2%LOGFILE% ... I'm using windows implementation of grep. The 2%LOGFILE% in both java and grep command is causing an error message indicating the file is being use by another process. The Ugly workaround i have came up with is to put grep error redirect to a temporary %LOGFILE%.aux java ... | grep ... 2%LOGFILE%.aux type %LOGFILE%.aux % %LOGFILE% del %LOGFILE%.aux What is a better solution?

  Read the article

• How can I systematically shut down Windows services in order?

  - by cbmeeks

  We have this open source application that has three (3) services. For the purpose of this question, let's call them A, B, and C. Now, they have to be shut down in a specific order. That order would be A then B then C. If B shuts down before A then we run into all kinds of problems. Same is true if C shuts down before B or A. Plus, each service can take a different amount of time to shut down due to how many users were using it. Oh, this need to be wrapped up in a DOS batch file or something a non-techy user could just double-click to initiate. (PowerShell is not out of the question but I've never used it). Also, I'm a C# coder so that could be used too. Anyway, when the restart is initiated the following needs to happen: 1) Initiate shutdown of service A 2) When service A is down, it should trigger the shutdown of service B 3) When service B is down, it should trigger the shutdown of service C 4) When service C is down, it should trigger the START UP of service A 5) When service A is UP, it should trigger the START UP of service B 6) When service B is UP, it should trigger the START UP of service C So as you can see, each stop/start needs to wait on the previous to be completely finished before moving on. And since each service can take a few seconds to a few minutes, we can't use any kind of timing tricks. Suggestions greatly appreciated. Thanks!

  Read the article

• How to interpret the bash command "usage" syntax?

  - by raoulsson

  How exactly do you have to interpret the output of a commands "usage" output, in bash for example. For example, on my OS X, cp gives me usage: cp [-R [-H | -L | -P]] [-fi | -n] [-apvX] source_file target_file cp [-R [-H | -L | -P]] [-fi | -n] [-apvX] source_file ... target_directory What does the nested options, like -H within -R, indicate? Does upper and lower case have any meaning? When is an argument optional, required? I need to implement a telnet command line against a program of mine and I would like to get this straight.

  Read the article

• Why is my ogg bigger than my m4a?

  - by acidzombie24

  I am using the following commands to encode an audio file to m4a & ogg formats: ffmpeg.exe -i 0123456789 -ab 192k out.m4a ffmpeg.exe -i 0123456789 -f wav - | oggenc2.exe - -r -q 6 -o out.ogg (0123456789 has no extension.) My m4a output is 14,608kB while my ogg output is 19,809kB. Why? AFAIK -q 6 is roughly 192kbps. So it should be about even. I could see one file being 1-3MB bigger than the other, but 5MB is pretty large. The m4a is almost 75% of the ogg! Why is this?

  Read the article

• Ubuntu dpkg error , after crash and filesystem error recovery

  - by Radian

  Ubuntu recently crashed , causing it's partition damaged ( which is EXT4) and Ubuntu was unable to boot , because it couldn't mount anything , only displays Busybox So I used the Live CD to run fsck on the partition, which fixed it , but deleted some nodes Now Ubuntu is working , but some files were missing , for example I lost the Panels configurations and Chromium's Extensions The Most Annoying problem , that there is some files corrupted , for example when I try to install any program, I got this (Reading database ... 95%dpkg: unrecoverable fatal error, aborting: files list file for package 'libservlet2.4-java' is missing final newline I tried these commands dpkg --configure -a apt-get -f install and from GUI , Synaptic Package Manager Fix Broken Packages So this file "libservlet2.4-java" Does anyone knows what it does ! and where it's location ? and how can I fix/get-correct-version-of it ? Also , is there any way I could tell Ubuntu to Check for ALL it's file , and if there is something corrupted it should recover it form the CD ?

  Read the article

• Granting rights to the sa account using osql

  - by Jan Jongboom

  I'm installing sql instances through script, and after creating a certain instance, I cannot get the sa account to be enabled through osql. What I've tried osql -S .\INSTANCENAME -E use master ALTER LOGIN sa ENABLE GO Using SSMS to enable the account (by logging in using Windows Auth., 'New query', and exactly the same query as in 1.) Suggestions in this issue No. 2. is actually working; and the account is enabled instantly. No 1 is not working, not even with the suggestions provided in 3., I have restarted the SQL services after executing the commands in osql. Additional info Windows 2003 Server, Microsoft SQL Server 2005 Enterprise, No password policies apply to the account.

  Read the article

• Debian based OS: Show system notification on clipboard copy/paste events

  - by ifischer

  When working with Linux (Debian based), I often experience problems in relation to the copy paste commands: I copy something with Ctrl+C or by selecting it with the mouse, but when I try to paste it somewhere else, the clipboard is empty and nothing happens - whatever reason caused this. This annoys me, as I have to switch to the source application again and again copy the text. So to really be sure if something was copied into the clipboard I would like it if the window manager (be it Gnome, KDE, etc) would show a Desktop Notification (for example powered by libnotify) as soon as anything is copied into the clipboard, showing the content that has been copied into the clipboard. Is that possible by using one of the many clipboard managers out there (glippy, clipit, ...)? If not, can I write a (DBus?)-hook, which is triggered during copy-to-clipboard-actions, showing the content which is to copy inside the Desktop Notification? (The latter approach would be more interesting, since I'm interested in hooking into system events in general)

  Read the article

• How to update Preview.app from the command line without losing focus on Mac OS X?

  - by snies

  I want to update Preview.app in the background from the command line without losing focus of my current window. I know that I can use the following to open/update the view of a file, but then I lose focus to the Preview.app. open -a Preview foo.pdf I guess there might be some clever AppleScript commands to do so but so far I didn't find the right one. Alternatively I would be interested into transfering the focus back to my current application directly after the update. I need this in order to update Preview.app's view of a PDF file through a vi autocmd after I update the PDF file according to changes in a TeX file I am editing. Here is an example of what I want to achieve but using Ubuntu and evince.

  Read the article

• Remapping keys on keyboard in Linux

  - by Anuj More

  I am currently using xmodmap for remapping keys like Caps Lock on my keyboard. However, my keyboard has a bunch of keys on the top that are rarely used (Multimedia keyboard with buttons like Internet, Music, Next song, Mute etc) I want to remap these keys to specific commands (Not keys). For example: Pressing the Internet button should fire up my Firefox (/usr/bin/firefox)(which happens only in Windows for me) Also I need to map a specific button to xkill. Is there a way to achieve this? Using: Fedora 14 on GNOME and KDE (both)

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• How to install MariaDB rpms in CentOS 6.4 using rpm (not yum cmd) + handling mysql-libs conflicts

  - by Pat C

  I need to script the install of MariaDB using the rpm command in CentOS 6.4. I can't use yum since it's going to be an offline install so there's no access to the repository. The only MySQL package installed is mysql-libs as various other packages in CentOS depend on it. When I did a test install of MariaDB with yum it correctly accounted for mysql-libs and uninstalled it at the end as MariaDB could handle the dependencies after it was installed: [root@new-host-6 ~]# yum install MariaDB-client MariaDB-common MariaDB-compat MariaDB-devel MariaDB-server MariaDB-shared Loaded plugins: downloadonly, fastestmirror, refresh-packagekit, security, verify Loading mirror speeds from cached hostfile * base: mirrors.kernel.org * extras: mirror.keystealth.org * updates: mirror.umd.edu Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package MariaDB-client.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-common.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-compat.x86_64 0:5.5.32-1 will be obsoleting ---> Package MariaDB-devel.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-server.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-shared.x86_64 0:5.5.32-1 will be obsoleting ---> Package mysql-libs.x86_64 0:5.1.66-2.el6_3 will be obsoleted --> Finished Dependency Resolution Dependencies Resolved ==================================================================================================================================================================== Package Arch Version Repository Size ==================================================================================================================================================================== Installing: MariaDB-client x86_64 5.5.32-1 mariadb 10 M MariaDB-common x86_64 5.5.32-1 mariadb 23 k MariaDB-compat x86_64 5.5.32-1 mariadb 2.7 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 MariaDB-devel x86_64 5.5.32-1 mariadb 5.6 M MariaDB-server x86_64 5.5.32-1 mariadb 34 M MariaDB-shared x86_64 5.5.32-1 mariadb 1.1 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 Transaction Summary ==================================================================================================================================================================== Install 6 Package(s) Total download size: 53 M Is this ok [y/N]: y Downloading Packages: (1/6): MariaDB-5.5.32-centos6-x86_64-client.rpm | 10 MB 00:06 (2/6): MariaDB-5.5.32-centos6-x86_64-common.rpm | 23 kB 00:00 (3/6): MariaDB-5.5.32-centos6-x86_64-compat.rpm | 2.7 MB 00:02 (4/6): MariaDB-5.5.32-centos6-x86_64-devel.rpm | 5.6 MB 00:06 (5/6): MariaDB-5.5.32-centos6-x86_64-server.rpm | 34 MB 00:23 (6/6): MariaDB-5.5.32-centos6-x86_64-shared.rpm | 1.1 MB 00:00 -------------------------------------------------------------------------------------------------------------------------------------------------------------------- Total 1.3 MB/s | 53 MB 00:40 warning: rpmts_HdrFromFdno: Header V4 DSA/SHA1 Signature, key ID 1bb943db: NOKEY Retrieving key from https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Importing GPG key 0x1BB943DB: Userid: "Daniel Bartholomew (Monty Program signing key) <[email protected]>" From : https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Is this ok [y/N]: y Running rpm_check_debug Running Transaction Test Transaction Test Succeeded Running Transaction Warning: RPMDB altered outside of yum. Installing : MariaDB-compat-5.5.32-1.x86_64 1/7 Installing : MariaDB-common-5.5.32-1.x86_64 2/7 Installing : MariaDB-server-5.5.32-1.x86_64 3/7 chown: cannot access `/var/lib/mysql': No such file or directory PLEASE REMEMBER TO SET A PASSWORD FOR THE MariaDB root USER ! To do so, start the server, then issue the following commands: '/usr/bin/mysqladmin' -u root password 'new-password' '/usr/bin/mysqladmin' -u root -h new-host-6 password 'new-password' Alternatively you can run: '/usr/bin/mysql_secure_installation' which will also give you the option of removing the test databases and anonymous user created by default. This is strongly recommended for production servers. See the MariaDB Knowledgebase at http://kb.askmonty.org or the MySQL manual for more instructions. Please report any problems with the '/usr/bin/mysqlbug' script! The latest information about MariaDB is available at http://mariadb.org/. You can find additional information about the MySQL part at: http://dev.mysql.com Support MariaDB development by buying support/new features from Monty Program Ab. You can contact us about this at [email protected]. Alternatively consider joining our community based development effort: http://kb.askmonty.org/en/contributing-to-the-mariadb-project/ Installing : MariaDB-devel-5.5.32-1.x86_64 4/7 Installing : MariaDB-client-5.5.32-1.x86_64 5/7 Installing : MariaDB-shared-5.5.32-1.x86_64 6/7 Erasing : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Verifying : MariaDB-common-5.5.32-1.x86_64 1/7 Verifying : MariaDB-server-5.5.32-1.x86_64 2/7 Verifying : MariaDB-devel-5.5.32-1.x86_64 3/7 Verifying : MariaDB-client-5.5.32-1.x86_64 4/7 Verifying : MariaDB-compat-5.5.32-1.x86_64 5/7 Verifying : MariaDB-shared-5.5.32-1.x86_64 6/7 Verifying : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Installed: MariaDB-client.x86_64 0:5.5.32-1 MariaDB-common.x86_64 0:5.5.32-1 MariaDB-compat.x86_64 0:5.5.32-1 MariaDB-devel.x86_64 0:5.5.32-1 MariaDB-server.x86_64 0:5.5.32-1 MariaDB-shared.x86_64 0:5.5.32-1 Replaced: mysql-libs.x86_64 0:5.1.66-2.el6_3 Complete! My question is, what is the equivalent way to install the MariaDB packages using the rpm command only as opposed to yum? If I do rpm -ivh MariaDB*.rpm, I will get a ton of messages like the following about conflicts with mysql-libs: file /etc/my.cnf from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 file /usr/share/mysql/charsets/Index.xml from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 I then used the --force option to install the MariaDB rpms and uninstalled mysql-lib, I didn't get any weird messages but I'm not sure that is the cleanest method to handle the conflicts and do the install. So can someone confirm that installing MariaDB with the following rpm commands would be the same as using yum to install the packages and handle mysql-libs conflicts/removal: rpm -ivh --force MariaDB*.rpm rpm -e mysql-libs Thanks for any input!

  Read the article

• Can iptables allow Squid to process a request, then redirect the response packets to another port?

  - by Dan H

  I'm trying to test a fancy traffic analyzer app, which I have running on port 8890. My current plan is to let any HTTP request come into Squid, on port 3128, and let it process the request, and then just before it sends the response back, use iptables to redirect the response packets (leaving port 3128) to port 8890. I've researched this all night, and tried many iptables commands, but I'm missing something and my hair is falling out. I thought something like this would work: iptables -t nat -A OUTPUT -p tcp --sport 3128 -j REDIRECT --to-ports 8990 This rule gets created ok, but it never redirects anything. Is this even possible? If so, what iptables incantation could do it? If not, any idea what might work on a single host, given multiple remote browser clients?

  Read the article

• Font for Wine that supports the entire character set of the Win32 Console?

  - by Brian Campbell

  I would like to be able to display in the Wine console all characters that the Win32 console can display. I've written a small test program to print out all 8-bit characters: #include <stdio.h> int main(int argc, char *argv[]) { int i, j; for (i = 0; i <= 0xF0; i+=0x10) { for (j = i; j <= i + 0x0F; ++j) printf("%2x:%c", j, (char)j); printf("\n"); } getchar(); return 0; } Under Wine, the best I can do so far is using Andale Mono: While this is what I see on Windows Server 2008: Is there anywhere I can legally download a font that will allow me to view all of those characters under Wine? edit I've found a set of DOS fonts that includes a CP437 font, which should cover the character set I'm interested in. However, even if I install this font, wineconsole doesn't seem to recognize it. Is there any way I can get wineconsole to use this font, or convert this font to a format that wineconsole can use? Or is there any way I can extract fonts from DOSEMU for use in Wine? Oh, and I should probably mention that I'm on Mac OS X 10.6.2, installing Wine via MacPorts, using the wine-devel package. more information I have tried installing some console fonts that should cover the full character set as Mac OS X fonts (such as the NewDOS font listed above, and a font I tried converting from the fonts supplied by DOSEMU). Wine does not seem to pick up on new fonts installed in Mac OS X. Is there a way to register new fonts I've installed with Wine? Would manually editing the system.reg file that seems to contain font mappings work, or is there something else I'd need to do? bump Bounty ends soon, I'm still looking for an answer for this. Does anyone use the Wine console for complex text user interfaces?

  Read the article

• performance wise htaccess

  - by purpler

  hese's the my htaccess template, i wonder if anything could be added to increase website performance.. # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US ServerSignature Off FileETag None Header unset ETag Options -MultiViews #Options All -Indexes # Force the latest IE version or ChromeFrame <IfModule mod_setenvif.c> <IfModule mod_headers.c> BrowserMatch MSIE ie Header set X-UA-Compatible "IE=Edge,chrome=1" env=ie </IfModule> </IfModule> # Proxy X-UA Setup <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> #Rewrites Options +FollowSymlinks RewriteEngine On RewriteBase / # Redirect to non-WWW RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] # Redirect to WWW RewriteCond %{HTTP_HOST} ^domain.com RewriteRule (.*) http://www.domain.com/$1 [R=301,L] # Redirect index to root RewriteRule ^(.*)index\.(php|html)$ /$1 [R=301,L] # Caching ExpiresActive On ExpiresDefault A0 Header set Cache-Control "public" # 1 Year Long Cache <FilesMatch "\.(flv|fla|ico|pdf|avi|mov|ppt|doc|mp3|wmv|wav|png|jpg|jpeg|gif|swf|js|css|ttf|eot|woff|svg|svgz)$"> ExpiresDefault A31622400 </FilesMatch> # Proxy Caching <FilesMatch "\.(css|js|png)$"> ExpiresDefault A31622400 Header set Cache-Control "private" </FilesMatch> # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Proper SVG serving AddType image/svg+xml svg svgz AddEncoding gzip svgz # GZip Compression <IfModule mod_deflate.c> <FilesMatch "\.(php|html|css|js|xml|txt|ttf|otf|eot|svg)$" > SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error page ErrorDocument 404 /404.html # Deny access to sensitive files <FilesMatch "\.(htaccess|ini|log|psd)$"> Order Allow,Deny Deny from all </FilesMatch>

  Read the article

• Access Java based keystore directly on Sun ONE Webserver 6.1

  - by George Bailey

  The keystore seems to reside in one of /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-cert8.db /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-key3.db What tool would I use to access this file? I have tried these commands which did not work. /opt/SUNWwbsvr/bin/https/jdk/bin/keytool -certreq -keyalg RSA -file /tmp/test.csr -keystore /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-cert8.db /opt/SUNWwbsvr/bin/https/jdk/bin/keytool -certreq -keyalg RSA -file /tmp/test.csr -keystore /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-key3.db /opt/SUNWwbsvr/bin/https/jdk/bin/keytool -list -storepass password -keystore /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-cert8.db /opt/SUNWwbsvr/bin/https/jdk/bin/keytool -list -storepass password -keystore /opt/SUNWwbsvr/alias/https-sub.domain.ext-hostname-key3.db They all gave me the error message keytool error: java.io.IOException: Invalid keystore format

  Read the article

• How to avoid tilde ~ in Bash prompt?

  - by Jirka

  Hello! I have set my prompt in bash in a such way that I can use it directly in scp command: My current PS1 string: PS1="\h:\w\n$" And the prompt looks like this: lnx-hladky:/tmp/plugtmp $ What I don't like at all is the fact that $HOME directory is displayed as tilde. Can this be avoided? It's causing problems when switching between different users. Example: lnx-hladky:~/DOC $ Documentation says: \w : the current working directory, with $HOME abbreviated with a tilde \W: the basename of the current working directory, with $HOME abbreviated with a tilde Is there any possibility to avoid $HOME being abbreviated with a tilde? I have found one way around but I feel like it's overcomplicated: PROMPT_COMMAND='echo -ne "\e[4;35m$(date +%T)\e[24m$(whoami)@$(hostname):$(pwd)\e[m\n"' PS1=$ Can anyone propose a better solution? I have a feeling it's not quite OK to run so many commands just to get prompt. (date,whoami,hostname,pwd). Thanks a lot! Jirka

  Read the article

• Serverlocation move and how can I Move the files

  - by Bernhard

  Hello together, I´ve a big problem. I have to move data from an old Webspace which is only accessibla by ftp. No we have a new root server which is accessible by ssh of course :-) No i Need to move all data from the old space but there is a lot of Gb of files. Is there a way to fetch all files directly from the old ftp to the storage and not over a third station (my local machine)? I´ve tried it with ftp but without success. I think I´ve used the wrong commands. Is there a way to etablish something like this including all files and directorys? Thank you in advance Bernhard

  Read the article

• SQL Server: Is it possible to prevent SQL Agent from failing a step on error?

  - by franklinkj

  I have a stored procedure that runs custom backups for around 60 SQL servers (mixes 2000 through 2008R2). Occasionally, due to issues outside of my control (backup device inaccessible, network error, etc.) an individual backup on one or two databases will fail. This causes this entire step to fail, which means any subsequent backup commands are not executed and half of the databases on a given server may not be backed up. On the 2005+ boxes I am using TRY/CATCH blocks to manage these problems and continue backing up the remaining databases. On a 2000 server however, for example, I have no way to prevent this error from failing the entire step: Msg 3201, Level 16, State 1, Line 1 Cannot open backup device 'db-diff(\PATH\DB-DIFF-03-16-2010.DIF)'. Operating system error 5(Access is denied.). Msg 3013, Level 16, State 1, Line 1 BACKUP DATABASE is terminating abnormally. I am simply asking if anything like this is possible in SQL 2000 or if I need to go in a completely different direction.

  Read the article

• Gvim displays wrong font when set from _gvimrc, but correct font when set from menus

  - by dggoldst

  This question applies to gVim running on Windows. I have the following line in my _gvimrc set guifont=Lucida_Sans_Typewriter:h11:cANSI When gVim starts up, it strange italicizes everything! A call to :set guifont shows that things seem to have been set correctly, as it returns guifont=Lucida_Sans_Typewriter:h11:cANSI Then I manually select Edit-Select Font ... and then choose Lucida Sans Typewriter, and font size 11 and submit, the italics disappear and it looks fine. I've posted my _gvimrc for reference at http://vim.pastey.net/132157 So my questions are: Why am I getting different results from setting it manually and from _gvimrc? Is there a way to capture the command that the dialog box is sending back to the program? It might include extra commands that I'm missing.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >