Search Results

Search found 671 results on 27 pages for 'ifconfig'.

Page 14/27 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

  • Host is unreacheble with static networking configuration via /etc/network/interfaces while GUI NetworkManager is ok

    - by Riccardo
    I have some trouble setting-up the network interface using the static IP configuration. I run ubuntu 12.04 kernel 3.11.0-22 with the back-ports enabled. I followed these instructions from help.ubuntu.com but there seems to exist some conflict between the GUI approach (NetworkManager) and the command line approach. $ sudo nano /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.1.1.50 gateway 10.1.1.10 netmask 255.255.255.0 dns-nameservers 192.168.3.45 192.168.8.10 $ sudo /etc/init.d/networking restart I than try to ping for example google.com ping -c 3 www.google.com the response is that the host is unreachable. The icon on the top right of the desktop says: wired network disconnected. If I work using the GUI approach (Edit Connections and so on...) all works great. Can same one explain to me where I wrong? $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 90:e6:ba:07:4a:77 inet addr:10.1.1.50 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::92e6:baff:fe07:4a77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39619 errors:0 dropped:0 overruns:0 frame:0 TX packets:18520 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19030895 (19.0 MB) TX bytes:2768769 (2.7 MB) $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0

    Read the article

  • Wired Network not working on Ubuntu 11.10 + Strange Behavior with Manual Conf

    - by Mauricio Cruz
    I'm new to Ubuntu - to be honest this is my very first day trying it... and I've already spent hours trying to make my wired connection work. I've been using this wired network with Windows and OSX, and in both systems I also had some trouble trying to connect in the past (and the troubleshooters did their magic and helped me get connected). Today, this is what I got: I'm running Ubuntu 11.10; ifconfig: eth0 Link encap:Ethernet HWaddr 78:2b:cb:c3:bf:8f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:343 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:70 (70.0 B) TX bytes:63273 (63.2 KB) Interrupt:20 Memory:e2e00000-e2e20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1859 errors:0 dropped:0 overruns:0 frame:0 TX packets:1859 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:149368 (149.3 KB) TX bytes:149368 (149.3 KB) wlan0 Link encap:Ethernet HWaddr 10:0b:a9:82:55:c0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:15484 errors:0 dropped:0 overruns:0 frame:0 TX packets:16871 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12048377 (12.0 MB) TX bytes:2677679 (2.6 MB) I also have some information from Windows ipconfig /all that I ran at my friend's machine Ipv6 Address: <address> preferential Ipv4 Address: 172.26.65.23 <preferential> Netmask: 255.255.254.0 Default Gateway: 172.26.64.1 DHCP Server : <address> DNS Servers : <address> DNS Suffix : <suffix> The weird thing is that I've tried to configure everything manually, using "Network Connections". When I add everything inside IPv4 Settings, the connection is finally successful, but only for 4~5 seconds before getting disconnected again... Update:I just changed the Connection Method to "Local-Link Only", and the same described above happens: At first, it says "Connection Stablished", but after a few seconds, the wired network gets disconnected. I hope someone can help me get connected! Thanks!

    Read the article

  • Setting up a static IP address (public) in Ubuntu

    - by ycseattle
    I have a business class internet connection and need to setup a static ip address for a machine. I did a search online and only find how to setup static local ip addresses (like 192.168..). I tried the same technique, and only setup the ip address and netmask, but after restart networking the computer could not connect to the outside world. This is what I did: 1) edit /etc/network/interfaces iface eth0 inet static address 173.10.xxx.xx netmask 255.255.255.252 2) edit /etc/resolv.conf search wp.comcast.net nameserver xx.xx.xx.xxx nameserver xx.xx.xx.xxx 3) restart network sudo /etc/init.d/networking restart Now the last step didn't report error, ifconfig shows the ip address was set, but this server cannot connect to outside world, ping google.com and reports "unknown host google.com". Any ideas?

    Read the article

  • High number of ethernet errors. Tool for testing the ethernet card?

    - by Fabio Dalla Libera
    I have an Asus Sabertooth X79. I often get corrupted files. I checked the RAM, but memtest finds no errors. To avoid the possibility of disk errors, I tried copying the files to tmpfs. If I copy from the network, I get md5sum mismatches about once every 10 times using a 6Gb file. Copying from RAM to RAM, I didn't get mismatches. I get a very high number of errors in ifconfig (compared to others PCs I just took as reference, which have 0 with much more traffic). Here is an example RX packets:13972848 errors:200 dropped:0 overruns:0 frame:101 The motherboard is new, but do you think there're some problems with it? What could I use to test the (integrated) network adapter? What else do you think I should double check? --edit-- I tried another NIC, it gives a lot of Corrupted MAC on Input. Disconnecting: Packet corrupt lost connection. I noticed that another PC downloads at 11.1MB/s without problems. This pc at 66.0 MB/s. Is there any way to try to limit the speed?

    Read the article

  • Cannot connect to Musicbrainz VirtualBox through SSH using Mac

    - by olovholm
    I am trying to connect my mac terminal shell to a VirtualBox running the Musicbrainz server. I have configured the network through a BridgeAdapter and running ifconfig on both the host and the guest show corresponding IP addresses. I can now ping the guest, but I cannot connect through SSH. The verbose output from the SSH client on my mac states: (olaenv)hf-79-202:Python oclovhol$ ssh -vv [email protected] OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 127.0.0.1 [127.0.0.1] port 22. debug1: Connection established. debug1: identity file /Users/oclovhol/.ssh/id_rsa type -1 debug1: identity file /Users/oclovhol/.ssh/id_rsa-cert type -1 debug1: identity file /Users/oclovhol/.ssh/id_dsa type -1 debug1: identity file /Users/oclovhol/.ssh/id_dsa-cert type -1 ssh_exchange_identification: Connection closed by remote host

    Read the article

  • sudo dhclient eth0 | sudo: unable to resolve host ubuntu

    - by Merianos Nikos
    I have a computer of a friend of mine, that runs Ubuntu (I don't know what version, due to the current system status) and while he was updating the kernel, he reboot the computer (yes that could be happen !!, anyway) Currently I am trying to recover the system by using a live USB, with Ubuntu installed on it. What I am doing, is the following: Update Failure The problem is that when I try to execute the fifth step, I am getting error because I do not have Internet access. The computer is properly wired on my rooter, and I have Internet access in any place apart of the shell. This message for example is send it via the live USB. but I cannot access the Internet via the shell. In my shell I try to use this command: sudo dhclient eth0 but the result of this command is the following message sudo: unable to resolve host ubuntu My hosts file has the following content: 127.0.0.1 localhost 127.0.1.1 ubuntu # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts how can I get connected on the Internet, in order to download the appropriate updates ? UPDATE 1 I just notice, that when I execute the ifconfig I am getting the following warning: Warning: cannot open /proc/net/dev (No such file or directory). Limited output. UPDATE 2 I just found that, and looks like solving the problem with dhclient eth0 command, but still I cannot ping Google UPDATE 3 Now the sudo dhclient eth0 returns the following message: RTNETLINK answers: File exists UPDATE 4 I just ping my rooter and I getting response, so, it is looks like I cannot ping outside the rooter (ie. Google) Kind regards ...

    Read the article

  • Intel 82576 Network card

    - by No1_Melman
    I have an Intel dual port pcie NIC card with two 82576 interfaces according to ubuntu 12.04. I run the command sudo lshw -html > /home/melman/Documents/hardware.html and it shows both of the interfaces but they're grayed out?! How can enable them? ifconfig output: bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.100.2 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr e0:69:95:d1:db:ff inet addr:192.168.10.63 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::e269:95ff:fed1:dbff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2903 errors:0 dropped:0 overruns:0 frame:0 TX packets:2627 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1524738 (1.5 MB) TX bytes:430196 (430.1 KB) Interrupt:20 Memory:f7f00000-f7f20000 eth3 Link encap:Ethernet HWaddr 00:50:b6:50:a7:f9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:1b:21:6e:99:77 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c00000-f7c20000 eth5 Link encap:Ethernet HWaddr 00:1b:21:6e:99:76 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c20000-f7c40000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:246 errors:0 dropped:0 overruns:0 frame:0 TX packets:246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17584 (17.5 KB) TX bytes:17584 (17.5 KB)

    Read the article

  • Wireless shows up as disabled, how can I get it working?

    - by Lazer
    $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

    Read the article

  • Wireless shows up as disabled, how can I get it working?

    - by Lazer
    $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

    Read the article

  • Diagnosing high CPU waiting

    - by Will
    I have a monitoring server that is running icinga/collectd/graphite with about 50 hosts. I have noticed high load/slugging performance on the box. If you take a look at top, you'll see: Cpu(s): 0.6%us, 0.2%sy, 0.0%ni, 7.6%id, 23.4%wa, 0.0%hi, 0.2%si, 0.0%st Notice the HUGE %wa value, which as far as I know means a network or disk bottleneck. ifconfig shows no dropping packets and there's not a ton of bandwidth going on, so that leaves disk issues, right? There's not a lot of disk writing going on either...iotop is reporting we're only writing a little over 1 MB per second and the RAID tool reports everything is A-OK and write caching is enabled. How do I go about trying to figure out how to fix this? UPDATE: iostat -x output is: avg-cpu: %user %nice %system %iowait %steal %idle 0.62 0.10 0.31 9.65 0.00 89.31 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.21 33.34 83.55 16.54 1599.94 399.07 19.97 43.21 416.98 3.71 37.13

    Read the article

  • How do I stop my ethernet network connection from dropping?

    - by Sean Hill
    My ethernet-based network connection doesn't stay up consistently. I'm running a ping against the gateway and it will: Work for a minute Freeze, time out, or give multi-second response times Repeat If it's stuck and I disable/enable networking through the network manager applet everything will work fine again for a minute. After 280 packets transmitted I'm getting 41% packet loss. I've tried a different cable and connection to the gateway but this had no effect. The distance to the gateway is just about 3 feet. Seems to work fine if I switch over to Windows, but Ubuntu is my main OS and I can't even use it right now as I depend on the network. My setup... OS: Ubuntu 11.04, dual-booting Windows 7 Mobo: Gigabyte Z68X-UD4-B3 CPU: Intel Core i7 2600K Edit A little clarification... Network Manager is still showing me as connected, but I am unable to reach to gateway or anything beyond. At no point does NM suggest the connection is lost and calling ifconfig shows that I still have an IP address. I tried connecting to a different gateway with a different cable and the same problem arises. As requested: lspci | grep -i eth 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) dmesg | tail -f [ 14.024709] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 [ 14.026443] EXT4-fs (sda7): re-mounted. Opts: commit=0 [ 14.176101] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj. [ 23.917731] eth0: no IPv6 routers present [ 726.109697] r8169 0000:07:00.0: eth0: link up [ 733.169494] r8169 0000:07:00.0: eth0: link up [ 753.930119] r8169 0000:07:00.0: eth0: link up [ 880.787332] r8169 0000:07:00.0: eth0: link up [ 1159.161283] r8169 0000:07:00.0: eth0: link up [ 1406.623550] r8169 0000:07:00.0: eth0: link up Edit @roland-taylor: Network is always available under Windows. Pings do not timeout, applications do not complain of no network availability, large downloads are not interrupted or slowed.

    Read the article

  • Pluscom MAC address shows up but "wireless unavailable"

    - by Luigi
    I've got a pluscom pci card plugged into my desktop and although the mac address shows up in network manager, it says "Wireless unavailable". I'm using Ubuntu 12.10 Gnome Shell Remix... edgar@edgarQuantal:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off edgar@edgarQuantal:~$ ifconfig eth0 Link encap:Ethernet HWaddr 6c:f0:49:02:1f:b8 inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fe02:1fb8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1425 errors:0 dropped:0 overruns:0 frame:0 TX packets:1393 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:995753 (995.7 KB) TX bytes:134079 (134.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:363 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:40828 (40.8 KB) TX bytes:40828 (40.8 KB) It looks the same as the problem as here, seems quite complicated: http://ubuntuforums.org/showthread.php?t=1993226 Tried downloading the driver but i get this: "Unpacking firmware-ralink (from .../firmware-ralink_0.36_all.deb) ... dpkg: error processing /home/edgar/Downloads/firmware-ralink_0.36_all.deb (--install): trying to overwrite '/lib/firmware/rt2870.bin', which is also in package linux-firmware 1.95"

    Read the article

  • Local Area Connection in Slacware 13

    - by asdasd
    I have windows xp and slackware 13 on one computer, and the ISP provided me a new modem. There was manual how to configure it, so i start the web browser and typed it's ip address 192.168.1.1 and the web interface of the modem appeared so i logged in, that was easy. But under slackware, i don't know how to enter in the modem config / web interface. I type in 192.168.1.1 but it's not working. Here's the output of ifconfig eth0 : eth0 Link encap:Ethernet HWaddr 00:a1:b0:01:18:28 inet addr:169.254.73.8 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 Memory:febff400-febff4ff How can i log in into the modem from linux, i.e. find it's assigned ip under slackware ? Thank you.

    Read the article

  • Any way to know if two ip address points to the same machine?

    - by Vivek V K
    Is there anyway to find if two different IP address in two different network actually points to the same physical device? I need it in Linux. Edit - I have the same server(a raspberry pi) connected via 2 intranets to my client. I don't know the IP address of the server as it is DHCP. The crude way to do is to reach the raspberry pi from one intranet and check with ifconfig to find the ipadress of the machine in the other Intranet. I want to know if there is any other way I can do it? I know the mac address of the machine.But I don't know how do I find the Ipadress based on the mac address.

    Read the article

  • Login Fail - Google Music Manager

    - by TX-NY-CA
    This is on a Surface Pro. I have not installed a virtual machine. Here is Google's feedback on the error message I receive when attempting login: "Login failed. Could not identify your computer" error message If you're receiving a 'Login failed. Could not identify your computer.' error, we couldn’t identify your machine. Please note that at this time, virtual machines aren't supported by Google Play. If you're certain that you don't have a virtual machine, some users have reported that they were able to workaround the issue by disabling their network bridge." My ifconfig feedback, in case that's helpful: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6640 (6.6 KB) TX bytes:6640 (6.6 KB) mlan0 Link encap:Ethernet HWaddr 60:45:bd:f9:04:c0 inet addr:10.129.116.166 Bcast:10.129.116.255 Mask:255.255.255.128 inet6 addr: fe80::6245:bdff:fef9:4c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:96714 errors:0 dropped:0 overruns:0 frame:0 TX packets:73079 errors:13 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:117500998 (117.5 MB) TX bytes:9008106 (9.0 MB)

    Read the article

  • CentOS: eth0 not starting on boot

    - by Cameron Aziz
    Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

    Read the article

  • How to create chroot jail with ability to change some system settings

    - by Tadeck
    How to properly create chroot jail (on Ubuntu, or some some other Linux if not applicable) to make user able to edit system settings (eg. with ifconfig) and be able to communicate with external scripts? The use case would be to enable user to authenticate using SSH and then be able to perform very limited set of actions from command line. Unfortunately the tricky part is the access to system settings. I have considered multiple options and the alternative is to setup fake SSH server (eg. with Twisted), try to use restricted shell (however, I seem to need chroot still), or write a script on top of the shell (?).

    Read the article

  • Have to run sudo dhclient eth0 automatically every boot

    - by Fyksen
    I just installed ubuntu 12.04.1 alternative install (for raid 0 on some disks). I Have some problems with the net. I'm at school, we use cable, and it got IPv6. If I run ifconfig eth0 heres my output: eth0 Link encap:Ethernet HWaddr e0:cb:4e:87:ff:db inet addr:128.39.194.217 Bcast:128.39.194.223 Mask:255.255.255.224 inet6 addr: 2001:700:1100:8008:e2cb:4eff:fe87:ffdb/64 Scope:Global inet6 addr: fe80::e2cb:4eff:fe87:ffdb/64 Scope:Link inet6 addr: 2001:700:1100:8008:48f7:c23:1d87:da6c/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1063378 errors:0 dropped:0 overruns:0 frame:0 TX packets:489811 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1577173461 (1.5 GB) TX bytes:37043669 (37.0 MB) Interrupt:68 Base address:0x6000 My /etc/network/interfaces look like this: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 # NetworkManager#iface eth0 inet dhcp # NetworkManager#hostname 2001:700:1100:1::4 # This is an autoconfigured IPv6 interface iface eth0 inet6 auto (I had to remove the hash tags, because of the BIGFONT i get on ask ubuntu) The "network manager" says that I'm not connected. Let me know if you need any more information. :)

    Read the article

  • Linux - use dhcp again to get IP

    - by Markus Orreilly
    I had statically set my ip in Linux using: sudo ifconfig eth0 192.168.blah.blah Now I want it to go back to using DHCP to assign the IP. How do I do that? This is what I see when I run dhclient Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/eth0/08:00:27:9b:43:09 Sending on LPF/eth0/08:00:27:9b:43:09 Sending on Socket/fallback DHCPREQUEST of 192.168.56.104 on eth0 to 255.255.255.255 port 67

    Read the article

  • Troubleshooting wireless network connectivity

    - by taserian
    I'm currently running Ubuntu 10.10, and I'm running into trouble keeping my wireless connection alive. After rebooting, I get about 5-10 minutes of a good speed connection; afterwards, the connection just zeroes out. I've gotten around to stirring up a shell script that gives me another 10 minutes or so of connectivity. Script contents below: #! /bin/bash sudo ifconfig wlan0 up echo "Enabling wireless device . . ." sleep 5 sudo iwconfig wlan0 essid MyNetworkName echo "Connecting to network. . ." sleep 10 sudo dhclient wlan0 echo "Getting IP address. . ." sleep 5 echo "Done. Closing window. . ." sleep 5 Shortly after running the line "sudo iwconfig wlan0 essid MyNetworkName" from the script, I notice the speed pick up. Other computers in my home running Windows XP are not affected by this problem, so all indications point to my Ubuntu machine. Does anyone have any pointers as to how to resolve this?

    Read the article

  • OSX Parallels 5 - can't share internet connection when using host-only networking...

    - by Steve Kirtley
    I've just upgraded from Parallels 3 to Parallels 5, but am having a problem matching my previous configuration. I am a web developer so run a local web server on my mac. I used to allow access to this from the virtual machines in Parallels by using 'Host-Only Networking' and then in OSX enabling internet sharing from my wifi/ethernet to the virtual ethernet ports that Parallels created. The setup was based on: http://www.craigfrancis.co.uk/features/setup/parallels/ The new version of Parallels doesn't create any network adaptors that are available for internet sharing in OSX - just VNIC's which only show under an ifconfig... Can anyone suggest how to make this all play nice? Thanks in advance! Steve

    Read the article

  • strange behaviour - dhclient needs to be run twice in order to connect to wireless

    - by splicer
    I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

    Read the article

  • How do I get wireless and video working on a Sony Vaio vpc-z21x9r

    - by Alex
    OS: Ubuntu 11.10 Kernel: 2.6.37.6 Laptop: sony vaio vpc-z21x9r The problem: I can't change level of screen backlight; also can't enable wi-fi. While using 3.0 kernel everything is ok, but the laptop discharges too quickly. Results for lspci 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 5f) VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) there is no wlan0 in ifconfig -a too. I've fount that kernel should already have drivers for this graphics controller, but when i load up in restore mode, it writes "fall" while trying to load up some video drivers. To change the level of backlight i've alrady tried: xbacklight -set XX , smartdimmer -s XX and got this init_ nvclock() failed! also sudo setpci -s 00:02.0 F4.B=XX with no results. As for wi-fi, i've found driver but i don't understand how to install it. Here it is How can I fix these problems? Thank you for your help and time! Also tried to fix problems with backlight writing GRUB_CMDLINE_LINUX_DEFAULT="quiet splash nomodeset acpi_backlight=vendor Still no results. Is there any sense in recompiling kernel, I mean 2.6.37.6. Can it make any improvements in the situation?

    Read the article

  • Just installed 13.04 and everything is fine except I cannot connect to the internet. Any thoughts?

    - by razorccatu
    I just installed Ubuntu 13.04 on my HP G62 laptop and the install went smoothly. I did the install off of a USB drive after trying ubuntu. While I was testing it, I connected to my Wireless with out issue and surfed a little. After the install, no wireless. I can still connect to my wireless network (at least it tells me I'm connected at full strength) but No servers can be found. I attempted to ping Google to no avail and I attempted to ping my router to no avail. I tried to then hard wire the machine and once again it told me that I was connected but I was not. When I ran dmesg, I got the following message: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolvabe. Please install nss-hostname! Is the hostname the issue? if so, how do I resolve it with out internet connection? If it's not the issue, how do I move forward? Thanks for any help. EDIT. I forgot to attach the image of my ifconfig if that might help.

    Read the article

  • Brother MFC-J470DW scan function "Check Connection"

    - by user292599
    I have a Brother MFC-J470DW printer that I have connected to a Linux desktop (running Ubuntu 14.04) using a wireless router network. The printer works fine for printing and copying, but now I want to add the scan function. To set up the scan function, I went to the Brother web page for this printer: http://support.brother.com/g/b/downloadlist.aspx?c=eu_ot&lang=en&prod=mfcj470dw_us_eu_as&os=128 and under Scanner Drivers selected "Scanner driver 64bit (deb package)", "Scan-key-tool 64bit (deb package)", and "Scanner Setting file (deb package)". For each package, I clicked the EULA, and selected "open with Ubuntu Software Center". Then after the USC window pops up, I click on Install and the red line goes from left to right. In each case, the USC window then had a green checkmark and the Install box changes to Reinstall (that's how you know it worked). So now I try it out. Hitting the Scan button on the printer, selecting "Scan to file", and hitting ok produces the message "Check Connection". I checked the Brother Linux Information FAQ (scanner) page and the 14th question seems the same as mine: When I try to use the scan key on my network connected machine, I receive the error "Check connection" or I can not select anything except "scan to FTP". I explored the solution given for this FAQ, but found from ifconfig that I am already using eth0, the default setting, so presumably that is not the problem. I also found brscan-skey installed in /usr/bin and did drrm@drrmlinux2:~$ brscan-skey -t drrm@drrmlinux2:~$ brscan-skey but that didn't help - I still get the "Check connection" message. What can you suggest to fix this problem?

    Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >