Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 14/287 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• cisco ePC 3208 router and captive portal

  - by Dejan Milosevic

  Ok, i have cisco ePC 3208 router, and cable internet goes in router via cable and router is emiting wireless. It can work without computer and it is working fine. Now i want to have capiteve portal with home page for my buisness and user logins. Is it possible that i use computer as gateway for captive portal, so when user goes to wireless it will redirected to computer local server for authorization and then passed by if user and pass is good, or i need another router or wifi acess point?

  Read the article

• 5GHz vs 2.4GHz dual band router, max mbps

  - by Tallboy

  I've done a fair amount of reading before posting this but there are a few things still unclear. I just bought a Netgear WNDR3700 N600. I understand that 5GHz offers more channels, less interference because of more available channels, wont interfere with a microwave and so on, and also has a shorter range. Currently, my router is broadcasting both signals (for my iPhone on 2.4, and my computer on 5) But my question is What is the max speed of 5GHz in mbps? In the router settings, it allows me to set '300mbps', but I keep reading online that the max is 54. Is this true? I noticed when I set up the router the default for 2.4 was set to 300 and the default for 5 was set to 54, so I changed both to 300. Is this fine as well? I don't see why it wouldn't be maxed out for both by default. On the box it says max rate of 300+300 so I assume this is correct, but it's throttled down so the router isn't stressing in case you have something streaming media 24/7 and slowing the internet down too. What is the max range of 5GHz? my apt is 780 square feet, and the router is in the main living room.

  Read the article

• Windows XP periodically disconnects, reconnects; Windows 7 doesn't

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

  Read the article

• Setting up a WPA-PSK network card to connect to a WPA2 network

  - by mattshepherd

  I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

  Read the article

• Windows XP can't connect to wireless network

  - by mikez302

  I have a desktop computer with a wireless card, running Windows XP SP3. For a little while, I had a remote network connection set up for my job, but I didn't need the remote connection so I deleted it. Now, I am unable to connect to the internet at all from that computer through my wireless router. I can connect through my router using my laptop, and I can connect through my neighbor's router using my desktop, but for some reason I can't connect through my own router using my desktop. I see the "Wireless Network Connection 5" icon in my system tray, but it tells me it is not connected. When I click on the icon, I see a list of wireless networks, including my own, which is set up to automatically connect, although it doesn't. When I try to connect to my network on my own (by clicking on it, then clicking "Connect"), it asks me for my network password like it usually does. I see a box come up saying "Waiting for network to be ready..." and it hangs there. On the list of wireless networks, my network says "Acquiring network address" but it doesn't actually connect. How can I fix this? I tried rebooting my computer, repairing my connection, and restarting my router, and I am still having this problem.

  Read the article

• my laptop wireless registers as 169.254.111.111

  - by Roalt

  I sometimes gets an ip address of 169.254.111.111 received for my laptop (instead of one in the 10.0.0.x range). I thought it was a problem with my Ubuntu system, but after I dual-booted I got the same problem under Windows Vista with the same laptop. What's the problem, why does it happens only sometimes, and how can it be solved? For the record: I'm using a Linksys WRT610N wireless router.

  Read the article

• My NetGear router suddenly started showing limited access for all wifi connected laptops

  - by Yasser

  I have netgear n300 router which I had installed about 6 months back. Here is how the setup is, I have a local internet provider by the name of "Hathway" they have this modem which is in turn connected to the router and a wire from router is connected to my desktop. As shown in this pic below, except for the laptop I use a desktop rest all the connection is same So with this connection and the below configuration, every thing worked fine. The desktop would work also all my laptops and mobile devices would connect and be able to access the internet without any problem. Now suddenly since yesterday (with no changes made whatsoever to this config) all my laptops start showing the limited connection message and cannot connect to the internet. However the desktop which is connected can access the internet. Can someone please guide me on this.

  Read the article

• Windows periodically disconnects, reconnects to the network

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

  Read the article

• Hardware needed to route between two networks over wireless

  - by AptDweller

  I recently rented an apartment about 100 yards from my brother's house. I have line of sight to his house and can pick up his home AP signal with one of my two laptops if I go out on my balcony (facing his house) or put the laptop by the window. The other laptop will sometimes see the SSID broadcast, but fails to connect, drops, etc. We would like to set up a persistent wireless connection between our homes. We would prefer each network be logically segmented as independent networks, but he will share his internet connection. I've got a bunch of tv shows saved to a NAS by my TiVO that I'd like to make available to him across the wireless link. My brother strongly prefers to not mess with his WAP at all. His network is running fine and is afraid to mess it up. I guess you could say he is "technologically declined". If we can get a reliable 11Mbps connection we will be satisfied. What hardware do I need to make this work? I was thinking a router with two wireless interfaces (external antennas) a wired interface, and a directional antenna mounted on my balcony facing his house. Can anyone recommend hardware to make this happen? Cheaper is better. I'll only be living in the area a year or two. I do have an old satellite TV antenna if that can be used to direct the signal.

  Read the article

• Ways to have audio output without wires

  - by viraptor

  I'm trying to find a way of using my home speakers/amp without actually having to connect them. There are two laptops that use them normally (so I don't like changing the connection all the time) and I'd rather move the speakers to a place that's away from the couch. I'm not sure how to do this though... The options I can think of are: some kind of wireless jack-jack connection finally getting a media server Unfortunately I can't find any good product for the first solution. I've seen some headphones which have the receiver integrated and a separate transmitted, so in general the idea is already out there, just not the way I need ;) I've seen also http://www.miccus.com/products/blubridge-mini-jack, but I'd have to have a compatible receiver which I can't find on its own (maybe there's some application that the media server could use?). As far as media server goes... many of the plug servers look really interesting, but I'm not sure how to create an audio output and how to redirect the input really. None of the plug servers I've seen so far advertises the option of audio output jack port. I think this part could be fixed by getting one with an usb port and a separate cheap usb soundcard. I hope that input can be sorted out in some rather simple way. I've got Linux running on both laptops so I hope that would be possible to configure jack/pulse/whatever to use the remote endpoint, or even write a simple local-/dev/dsp:network:media-server-/dev/dsp forwarder. So the main question is... are there better ways? Are there any out of the box solutions? Or maybe this was already done by someone and described somewhere?

  Read the article

• Wireless network relay?

  - by IPX Ares

  Is there hardware (links would be great) that can connect to the wireless internet already in my house and provide hard links to other hardware? Basically the problem is that my basement is not wired up to let me hook up my cable modem. I have some electronics that do not have wireless and need a LAN wire. Is there something I could plug in downstairs to act as a relay hub?

  Read the article

• Why is my Wifi connection slower than ethernet even though bandwidth should saturated?

  - by supercheetah

  I'm wondering why it is that my wireless connection is slower than my wired connection for things going to the outside world (so, not files being transferred within the network), which is should be faster than the outside connection, which, I would think, would mean that downloading something like an ISO or other large file from the Internet should be the same either way since that should saturate the connection anyway. Does it have something to do with the encryption (WPA)? Could it have something to do with MTU since the MTU for ethernet can be in the range of 1500 to 9000 bytes, and 2304 bytes for 802.11? Do wireless packets have to be buffered, whereas this wouldn't be an issue with ethernet? What's the math behind the difference?

  Read the article

• Ubuntu 9.10 Internet not working

  - by Mr. Man

  I am using a BlueProton USB wireless network adapter and an Ubuntu 9.10 machine and the machine says that it is connected to the internet but it won't see other machines/devices on the local network and only a few websites work.

  Read the article

• Laptop kicks other users off the wifi when it connects, then gets disconnected itself

  - by Devon

  I've got an Acer Aspire One running Linux. When I connect to my building's wifi, everything seems fine for a short period of time (I can google a few things or start downloading an Apt package), but then other devices on the network lose their IP addresses. Shortly after that, my computer also gets disconected. My computer is set to use DHCP. What causes this, and do you know how it could be fixed? Am I causing a broadcast storm?

  Read the article

• Why is adhoc connection without internet faster than via router?

  - by user29951

  Hi, I'm transferring some data from my desktop to my laptop trough wifi. My home network is managed with windows 7 homegroup When my 2 pc's are connected via my router (with internet access) i get max 200 KB/s and when i create a ad hoc wifi i get 1.5 MB/s why is that... (copying data via network name ex: \\PC2)

  Read the article

• Ad-hoc connection between iPhone and Macbook Pro

  - by Phil Nash

  I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

  Read the article

• MBP Bluetooth PAN connection with iPhone 4

  - by Chetan Sachdev

  I am trying to share MBP(OSX 10.8.3) internet connection with iPhone 4 (iOS 6) using Bluetooth PAN(Personal Area Network). Problem is Bluetooth PAN is not getting an ip address. I have tried to renew DHCP lease but nothing works. When I give a Manual IP address, the Bluetooth PAN goes green but doesn't shows the connection in iPhone. Is it possible to share the internet connection via Bluetooth. Note: I don't want to create an Ad-hoc connection over wifi.

  Read the article

• Disable WLan if Wired/Cable Network is available

  - by ifischer

  The question says it all. All i want is that my W-Lan connection should be disabled whenever a wired connection is available. What would be the easiest way to do that in Ubuntu/Gnome? In all guides (for instance some about guessnet) i found i had to configure my whole network configuration (WPA keys, DHCP, ...), but i find that a bit too complicated for such a simple use case. I just want to disable wlan0 when eth0 is connected.

  Read the article

• How to take advantage of two Internet connections (WiFi / Wired) ?

  - by Madhur Ahuja

  I have two separate internet connections, one through WiFi and other Wired. However, generally I have observed that Windows try to use only one ( mostly faster one/ Or Wired by preference - I am not sure). Is there a way I can take advantage of having both ? For example I can have my web browser use the wired one and my torrent software use the Wifi One. PS: This question may be regarded as duplicate but reason I am posting it again is I have not found any concrete answer for it. Two internet Connections, one LAN - how to share?

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• Diagnosing extremely slow network operations.

  - by Chris Becke

  The network: * A windows 7 PC with 2 NICs - one connected to an old style ethernet hub - the other to the internet - with internet sharing enabled * An Apple iMac connected to the hub, successfully utilizing the ICS to access the internet. My problem: Using the Mac, copying from the internet is fast. However, if I connect to a SMB: share on the Windows 7 PC and try and copy anything a few kb the copy operation is appallingly slow with my network card using the Windows 7 control panel showing ~.1% utilization. The NICs are 100Mbs and show a 10x larger throughput (now ~1%) if I download large files over the internet using the Mac. WTF?

  Read the article

• How to troubleshoot intermittent and irregular connection errors on home network (preferrably Mac client)

  - by Martin

  Hi, I'm experiencing intermittent connection errors in our home network from two different computers, normally "Connection Reset" when browsing, but also other issues such as very slow throughput. I have approximately a network setup as below: ISP-Cable Modem-Dlink DIR 655 Router-(Ethernet)-Fon Router-Mac/Windows laptop Basically, is there a simple way to monitor the network and detect where issues are coming from? Right now we don't know if it is the Fon router, the Dlink router, the modem or the ISP. As the issue is intermittent, is there a software that regularly traceroutes a set of destinations and tests e.g. throughput, something that can help us figure out where in the chain the errors are introduced? The more automatic network monitor, the better.

  Read the article

• Get Internal IP Address From DHCP Hostname

  - by ell

  I would like to try and get an internal ip address of one of the computers on my network. The reason for this is I have a little home server box downstairs but every time I want to SSH into it I have to open my router configuration and go on the DHCP client table and look at the IP address. For example I would like to be able to go ssh ell-sever instead of ssh 192.168.1.105 or whatever it happens to be. My network configuration is like so: Router downstairs that is connected to the Internet and is running a DHCP server My server computer (ell-server) is a headless pc connected to the router via ethernet cable. Running Ubuntu 11.04 Server Edition My laptop upstairs (ell-laptop) that is running Ubuntu 11.10 Desktop Edition connected wirelessly Other (irrelevant) computers - 2 x Windows XP, 1 x Xubuntu - all connected with cables. (It seemed to me the method of connection isn't useful information but I put it in anyway - just in case. If I have missed any information please tell me) Do I have to run a DNS server on one of my computers? If so which one? And does that mean I will have to run a DDNS client on each computer? Thanks in advance, ell.

  Read the article

• WiFi & GbE Slow while Both Active.

  - by Mark Tomlin

  I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

  Read the article

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >