Search Results

Search found 4511 results on 181 pages for 'andrew min'.

Page 140/181 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Cisco ASA Site-to-Site VPN Dropping

  - by ScottAdair

  I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

  Read the article

• Walmart and Fusion Apps

  - by ultan o'broin

  Photograph: Misha Vaughan I attended Fusion Apps (yes, I know I am supposed to say "Oracle Fusion Applications", but stuffy old style guides are a turn-off in interwebs conversations) User Experience Advocate (FXA) training in Long Beach, California last week; a suitable location as ODTUG KSCOPE 11 was kicking off and key players were in the area. As a member of Oracle's Apps-UX team I know the Fusion Apps messaging, natch, and done some other Fusion Apps go-to-market content work too. For the messaging details themselves, see Lonneke Dikmans (@lonnekedikmans) great blog, by the way. However, I wanted some 'formal' training combined with the opportunity to meet and learn from people already out there delivering those messages. The idea in me reaching out to Misha Vaughan, Apps-UX FXA maven, to get me onto this training was that in addition to my UX knowledge, I could leverage my location in EMEA and hit up customer events more quickly and easily. Those local user groups do like to hear the voice of locals too you know (so I need to work on that mid-Atlantic accent). I'm looking forward to such opportunities. The training was all smashing stuff, just the right level of detail, delivered professionally and with great style and humor. I was especially honored to be paired off for my er, coaching with Debra Lilley (@debralilley), who shared with everyone all kinds of tips and insights from her experiences of delivering the message and demo. For me, that was the real power of the FXA event--the communal, conversational aspect--the meeting up with people who had done all this for real, the sharing in their experiences, while learning along with other newbies. Sorry, but that all-important social aspect doesn't work so well with remote meetings. Katie Candland (Apps-UX) gave us a great tour of the Fusion Apps demo and included some useful presentational tips too (any excuse to buy that iPad). It's clear to me that the Fusion Apps messaging and demos really come alive with real-world examples that local application users will recognize, and I picked up some "yes, that's my job made easier" scene-stealers from Debra and Karen Brownfield too, to add to the great ones already provided. This power of examples shouldn't surprise anyone, they've long been a mainstay of applications user assistance, popular with users. We'll offer customers different types of example topics in the Fusion Apps online help too (stay tuned), and we know from research how important those 3S's (stories, scenarios, and simulations) are to users when they consume and apply information. Well, we've got the simulation, now it's time for more stories and scenarios. If you get a chance to participate in an FXA event (whether you are an Oracle employee or otherwise), I'd encourage it. It's committing your time and energy for sure, but I got real bang for the buck from it for my everyday job too. Listening to the room's feedback on the application demo really brought our internal design work to life, and I picked up on some things that I need to follow up on (like how you alphabetically sort stuff in other languages). User experience is after all, about users. What will I be doing next, and what would I like to see happen? Obviously, I need to develop my story-telling links with the people I met in Long Beach and do some practicing with the materials, and then get out there and deliver them at a suitable location. The demo is what it is right now, and that's a super-rich demo that I know everyone will want to see and ask questions about. Then, as mentioned by attendees at the FXA event, follow up on those translated and localized messages for EMEA (and APAC), that deal with different statutory or reporting requirements of the target markets. Given my background I would say that, wouldn't I? However, language is part of the UX, and international revenue is greater than US-only revenue for Oracle, so yes dear, we all need to get over the fact that enterprise apps users don't all speak, or want to speak, American-English. Most importantly perhaps, the continued development of a strong messaging community between Oracle and partners and customers where we can swap and share those FXA messaging stories and scenarios about Fusion Apps in a conversational way. The more the better, a combination of online and face-to-face meetings. I must also mention the great dinner after the event at Parker's Lighthouse, and the fun myself and Andrew Gilmour (Apps-UX) had at our end of the table talking about just about everything except Fusion Apps with Ronald Van Luttikhuizen and Ben Prusinski (who now understands the difference between Cork and Dublin people. I hope). Thanks to all the Apps-UXers who helped bring the FXA training to town, and to Debra and all the others that I am too jetlagged to mention right who were instrumental in making it happen for me. Here's to the next one. And the Walmart angle? That was me doing my Robert Scoble (ScO'bilizer?)-style guerilla smart phone research in Walmart in Long Beach, before the FXA event. It's all about stories for me. You can read more about it on the appslab blog (see the comments).

  Read the article

• Dealing with AVCHD. Any free software to extract or edit AVCHD video?

  - by Kelsey

  I have a Panasonic HDC-SD5 video carmera which records in HD format to a memory card. It also came with a DVD burner which burns this format to DVD which I need a blu-ray player to view. I can get about 30 min worth of video on 1 DVD. My problem is the software that comes with the camera is not very good at all so I am constantly just using the 'backup' feature in the included burner (connect drive to camera, push backup, and it spits out up to 4 DVDs worth of HD video). Now that I have the video backed up on DVD in the HD format (blu-ray), is there any free software that I can use to edit this video and create other HD DVD's with my own menus, transitions, etc? I was considering buying Pinnacle Studio but I wanted to exaust any free options before biting the bullet. Any suggestions for software I could use or anything else I could do to make dealing with this AVCHD format any easier that I am unaware of? Edit: Sorry forgot to include that I am running Windows Vista 64-bit. Edit: Still haven't found anything that is truely free. Everything has limitations by either time, watermark the video or degrade the quality. Edit: So I still haven't found really anything, so is there some software I can use to convert the video to another format that I then could use to edit the video?

  Read the article

• Laptop Acer Travelmate 4050 takes over 10 Mins to POST

  - by Belliez

  Hi, I am a computer tech and have received a laptop for repair. I noticed when I turned it on the laptop would not do anything for a min or two (the fan would run up and stop, power led would shine and some cd rom activity then stop). It would sit there with a black screen. Suddenly after a random number of minutes (between 1-20mins!) the Acer BIOS screen would display and POST would happen before booting into Windows XP. It has frozen in XP at various times and pointed towards a CPU fault and over heating. The fan was on its last legs, sounded like a car engine, so I replaced this. Still same issues. I next replaced the CPU like for like. Same problems. Also applied new thermal paste between the cpu and heatsink, when running the fan kicks in occasionally (not as often as I thought it would) and I left it playing mp3, online radio and updating to service pack 3 and it wouldnt freeze. shutting down ok, cold start, not ok. Waits again before showing the BIOS screen. The hard disk was also making a screaming noise (SMART test and chkdsk passed) but I also replaced this. The laptop powers up with and without the battery so dont think its a battery issue. Running out of ideas and wondered if anyone had any advice. Thanks

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad? [closed]

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• iptables-restore: line 1 failed

  - by Doug

  Hello, I am new to servers, and I was following this guide and it failed on the first command instructed. Could anyone give me a hand? http://wiki.debian.org/iptables ~ZORO~:/etc# iptables-restore < /etc/iptables.test.rules iptables-restore: line 1 failed Edit: iptables.test.rules ~ZORO~:/etc# cat /etc/iptables.test.rules *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You could modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections for script kiddies # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Now you should read up on iptables rules and consider whether ssh access # for everyone is really desired. Most likely you will only allow access from certain IPs. # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls (access via 'dmesg' command) -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy: -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• backup of TFS with DPM 2007 - different backup times

  - by user46516

  I have DPM set up to back up my TFS server every 30 minutes, the reason being it's a way better interface than the quirky SQL backup interface. I also do a full backup nightly using an SQL maintenance job. My thinking is I would use DPM to restore my databases in case of losing my database and the nightly full backup would be a "just in case" the DPM restore doesn't work. I was thinking a little harder about this set up today and started to think about the fact that the DPM backup of the individual databases happens at different 30 min windows.. i.e. one happens at 13h30, another at 13h34 etc. Would this difference in time be a problem when it comes to restoring the TFS server? If I restore the databases and they are from different times, will this create corruption with pointers in one database pointing to missing items in the other database.. do the databases even rely on each other or are they completely interdependant. Lastly, how would SQL (log) backup cope with this?

  Read the article

• Logmein does not work at home?

  - by Littlet-ENG

  I've been using logmein successfully for may situations and have had very good success. Our company has an Log me in Pro account. I have used this to share my desktop with customers. At work, I have had no problem with my laptop. At home, one program (solid-works) that I need to share with my customers, will not display the active screen. I spent 45 min on the phone with both the software for the cad system and logmein support with not help. I need help in narrowing down what the problem is on my computer. The support guys at Solid-works got another remote software to work, so its not the program. I can get the logmein to work at the office so its not the settings of the logmein pro account. The LMI people say its a setting on my computer.? -internet is fast enough at home -can't narrow down the problem -changed graphical settings and that didn't work. Any Suggestions?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Any ideas? Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp2 KB896256 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• How to check DVD integrity at max read speed of DVD writer

  - by ashishsony

  I need to check the integrity of burned DVDs so that I can be sure about my backed-up data. I use DL-DVDs to take the backup. Earlier I used VSO Inspector software for the same but the day I switched to DL-DVDs the VSO Inspector gives me errors upon checking. I think the errors are because the switching of layer writing involves some dummy data somewhere. Secondly, it's damned slow for checking. I believe if there is a utility that can read all files (not the disk surface) and report if some files are unreadable would do the job. But it should be quick! Nobody wants to sit for disk checking for 3-4 hours after a quick 30 min data burn! I am looking for such a utility on Windows or Linux. Even scripts (python, etc) will do. I just want to be assured that the data is safe. Can someone help me in this? Thanks.

  Read the article

• Announcing Solaris Technical Track at NLUUG Spring Conference on Operating Systems

  - by user9135656

  The Netherlands Unix Users Group (NLUUG) is hosting a full-day technical Solaris track during its spring 2012 conference. The official announcement page, including registration information can be found at the conference page.This year, the NLUUG spring conference focuses on the base of every computing platform; the Operating System. Hot topics like Cloud Computing and Virtualization; the massive adoption of mobile devices that have their special needs in the OS they run but that at the same time put the challenge of massive scalability onto the internet; the upspring of multi-core and multi-threaded chips..., all these developments cause the Operating System to still be a very interesting area where all kinds of innovations have taken and are taking place.The conference will focus specifically on: Linux, BSD Unix, AIX, Windows and Solaris. The keynote speech will be delivered by John 'maddog' Hall, infamous promotor and supporter of UNIX-based Operating Systems. He will talk the audience through several decades of Operating Systems developments, and share many stories untold so far. To make the conference even more interesting, a variety of talks is offered in 5 parallel tracks, covering new developments in and  also collaboration  between Linux, the BSD's, AIX, Solaris and Windows. The full-day Solaris technical track covers all innovations that have been delivered in Oracle Solaris 11. Deeply technically-skilled presenters will talk on a variety of topics. Each topic will first be introduced at a basic level, enabling visitors to attend to the presentations individually. Attending to the full day will give the audience a comprehensive overview as well as more in-depth understanding of the most important new features in Solaris 11.NLUUG Spring Conference details:* Date and time:        When : April 11 2012        Start: 09:15 (doors open: 8:30)        End  : 17:00, (drinks and snacks served afterwards)* Venue:        Nieuwegein Business Center        Blokhoeve 1             3438 LC Nieuwegein              The Nederlands          Tel     : +31 (0)30 - 602 69 00        Fax     : +31 (0)30 - 602 69 01        Email   : [email protected]        Route   : description - (PDF, Dutch only)* Conference abstracts and speaker info can be found here.* Agenda for the Solaris track: Note: talks will be in English unless marked with 'NL'.1.      Insights to Solaris 11         Joerg Moellenkamp - Solaris Technical Specialist         Oracle Germany2.      Lifecycle management with Oracle Solaris 11         Detlef Drewanz - Solaris Technical Specialist         Oracle Germany3.      Solaris 11 Networking - Crossbow Project        Andrew Gabriel - Solaris Technical Specialist        Oracle UK4.      ZFS: Data Integrity and Security         Darren Moffat - Senior Principal Engineer, Solaris Engineering         Oracle UK5.      Solaris 11 Zones and Immutable Zones (NL)         Casper Dik - Senior Staff Engineer, Software Platforms         Oracle NL6.      Experiencing Solaris 11 (NL)         Patrick Ale - UNIX Technical Specialist         UPC Broadband, NLTalks are 45 minutes each.There will be a "Solaris Meeting point" during the conference where people can meet-up, chat with the speakers and with fellow Solaris enthousiasts, and where live demos or other hands-on experiences can be shared.The official announcement page, including registration information can be found at the conference page on the NLUUG website. This site also has a complete list of all abstracts for all talks.Please register on the NLUUG website.

  Read the article

• High CPU usage in my digitalocean droplet

  - by Ibrahim Azhar Armar

  I am experiencing high CPU usage here is the stats i got from server, the consumption after every restart in 15 minutes go upto 100%, what could go wrong? I have a wordpress copy installed on the server which does not have much traffic, here is the stats that i got from using top command in server. top - 11:46:02 up 12 min, 3 users, load average: 40.89, 16.03, 6.11 Tasks: 132 total, 41 running, 91 sleeping, 0 stopped, 0 zombie Cpu(s): 24.3%us, 61.5%sy, 0.0%ni, 0.0%id, 4.0%wa, 0.0%hi, 0.0%si, 10.2%st Mem: 2050896k total, 1988656k used, 62240k free, 284k buffers Swap: 0k total, 0k used, 0k free, 4712k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31 root 20 0 0 0 0 R 39 0.0 1:35.53 kswapd0 899 root 20 0 15988 172 0 S 14 0.0 0:05.00 irqbalance 418 syslog 20 0 243m 600 0 S 13 0.0 0:06.85 rsyslogd 944 mysql 20 0 1320m 53m 0 S 12 2.7 0:21.15 mysqld 2357 root 20 0 17344 532 164 R 11 0.0 0:14.27 top 960 root 20 0 246m 3816 0 S 3 0.2 0:08.18 php5-fpm 2431 www-data 20 0 344m 64m 908 R 2 3.2 0:04.23 apache2 2435 www-data 20 0 304m 63m 836 R 2 3.2 0:03.43 apache2 2413 www-data 20 0 349m 63m 920 R 2 3.2 0:07.51 apache2 2465 www-data 20 0 349m 64m 944 R 2 3.2 0:05.04 apache2 2518 www-data 20 0 307m 41m 1204 R 2 2.1 0:01.37 apache2 2406 www-data 20 0 346m 56m 1144 R 2 2.8 0:03.76 apache2 2456 www-data 20 0 345m 55m 1184 R 2 2.8 0:02.67 apache2 2373 www-data 20 0 351m 63m 784 R 2 3.2 0:11.09 apache2 2439 www-data 20 0 306m 35m 916 R 2 1.8 0:02.51 apache2 2450 www-data 20 0 345m 55m 1088 R 2 2.8 0:02.96 apache2 2486 www-data 20 0 299m 10m 876 R 2 0.5 0:01.19 apache2 2523 www-data 20 0 300m 27m 796 R 2 1.4 0:00.99 apache2

  Read the article

• Nginx and Gunicorn hanging on GET requests

  - by whatWhat

  I'm using Nginx + Gunicorn which is serving my Django project. All GET requests hang for ~1 min. The content seems to be available immediately as I can see it in the Browser inspector but the browser itself looks like it's still waiting for more data. Heres my Ngnix config #allow for up to 3 connections per second. limit_req_zone $binary_remote_addr zone=one:10m rate=3r/s; server { listen 80; server_name example.com; root /var/www/example.com/example/; # serve directly - analogous for static/staticfiles location /media/ { # this changes depending on your python version root /home/example/; } location /static/ { # if asset versioning is used if ($query_string) { expires max; } root /var/www/example.com; } location / { #Allow for a burst of 50. limit_req zone=one burst=50 nodelay; proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 10; proxy_pass http://localhost:8001/; } # what to serve if upstream is not available or crashes error_page 500 502 503 504 /media/50x.html; } My Gunicorn Config: bind = "127.0.0.1:8001" workers = 3 worker_class = "gevent" Is there anything obvious that would be causing the requests to stay open for so long?

  Read the article

• DNS issue on Fedora 12? wget wordpress.org fails where wget www.google.com works

  - by Tom Auger

  I'm administering a Fedora 12 box, but am quite new to networking specifics. Recently one of our WordPress apps hosted on our server has stopped being able to perform its auto-update or auto-download of plugins. Investigating further, I have tried the following: $ wget wordpress.org --2010-12-17 11:26:50-- http://wordpress.org/ Resolving wordpress.org... failed: Temporary failure in name resolution. wget: unable to resolve host address âwordpress.orgâ Whereas: $ wget www.google.com --2010-12-17 11:27:26-- http://www.google.com/ Resolving www.google.com... 74.125.226.82, 74.125.226.84, 74.125.226.80, ... Connecting to www.google.com|74.125.226.82|:80... connected. HTTP request sent, awaiting response... 302 Found Location: http://www.google.ca/ [following] --2010-12-17 11:27:26-- http://www.google.ca/ Resolving www.google.ca... 173.194.32.104 Connecting to www.google.ca|173.194.32.104|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: âindex.html.4â [ <=> ] 9,079 --.-K/s in 0.02s 2010-12-17 11:27:26 (462 KB/s) - âindex.html.4â Interestingly: $ ping wordpress.org PING wordpress.org (72.233.56.138) 56(84) bytes of data. 64 bytes from wordpress.org (72.233.56.138): icmp_seq=1 ttl=50 time=81.5 ms 64 bytes from wordpress.org (72.233.56.138): icmp_seq=2 ttl=50 time=67.3 ms ^C --- wordpress.org ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1783ms rtt min/avg/max/mdev = 67.361/74.448/81.536/7.092 ms and $ nslookup wordpress.org Server: 192.168.2.1 Address: 192.168.2.1#53 Non-authoritative answer: Name: wordpress.org Address: 72.233.56.138 Name: wordpress.org Address: 72.233.56.139 nscd has been stopped and flushed. iptables appear to be clean. At this point I have exhausted my limited abilities to diagnose the issue. Can anyone suggest a resolution path?

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Setting up vsftpd, hangs on list command

  - by Victor

  I installed vsftpd and configured it. When I try to connect to the ftp server using Transmit, it manages to connect but hangs on Listing "/" Then, I get a message stating: Could not retrieve file listing for “/”. Control connection timed out. Does it have anything to do with my iptables? My rules are as listed: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• #OOW 2012 : IaaS, Private Cloud, Multitenant Database, and X3H2M2

  - by Eric Bezille

  The title of this post is a summary of the 4 announcements made by Larry Ellison today, during the opening session of Oracle Open World 2012... To know what's behind X3H2M2, you will have to wait a little, as I will go in order, beginning with the IaaS - Infrastructure as a Service - announcement. Oracle IaaS goes Public... and Private... Starting in 2004 with Fusion development, Oracle Cloud was launch last year to provide not only SaaS Application, based on standard development, but also the underlying PaaS, required to build the specifics, and required interconnections between applications, in and outside of the Cloud. Still, to cover the end-to-end Cloud  Services spectrum, we had to provide an Infrastructure as a Service, leveraging our Servers, Storage, OS, and Virtualization Technologies, all "Engineered Together". This Cloud Infrastructure, was already available for our customers to build rapidly their own Private Cloud either on SPARC/Solaris or x86/Linux... The second announcement made today bring that proposition a big step further : for cautious customers (like Banks, or sensible industries) who would like to benefits from the Cloud value of "as a Service", but don't want their Data out in the Cloud... We propose to them to operate the same systems, Exadata, Exalogic & SuperCluster, that are providing our Public Cloud Infrastructure, behind their firewall, in a Private Cloud model. Oracle 12c Multitenant Database This is also a major announcement made today, on what's coming with Oracle Database 12c : the ability to consolidate multiple databases with no extra additional  cost especially in terms of memory needed on the server node, which is often THE consolidation limiting factor. The principle could be compare to Solaris Zones, where, you will have a Database Container, who is "owning" the memory and Database background processes, and "Pluggable" Database in this Database Container. This particular feature is a strong compelling event to evaluate rapidly Oracle Database 12c once it will be available, as this is major step forward into true Database consolidation with Multitenancy on a shared (optimized) infrastructure. X3H2M2, enabling the new Exadata X3 in-Memory Database Here we are :  X3H2M2 stands for X3 (the new version of Exadata announced also today) Heuristic Hierarchical Mass Memory, providing the capability to keep most if not all the Data in the memory cache hierarchy. Of course, this is the major software enhancement of the new X3 Exadata machine, but as this is a software, our current customers would be able to benefit from it on their existing systems by upgrading to the new release. But that' not the only thing that we did with X3, at the same time we have upgraded everything : the CPUs, adding more cores per server node (16 vs. 12, with the arrival of Intel E5 / Sandy Bridge), the memory with 512GB memory as well per node,  and the new Flash Fire card, bringing now up to 22 TB of Flash cache. All of this 4TB of RAM + 22TB of Flash being use cleverly not only for read but also for write by the X3H2M2 algorithm... making a very big difference compare to traditional storage flash extension. But what does those extra performances brings to you on an already very efficient system: double your performances compare to the fastest storage array on the market today (including flash) and divide you storage price x10 at the same time... Something to consider closely this days... Especially that we also announced the availability of a new Exadata X3-2 8th rack : a good starting point. As you have seen a major opening for this year again with true innovation. But that was not the only thing that we saw today, as before Larry's talk, Fujitsu did introduce more in deep the up coming new SPARC processor, that they are co-developing with us. And as such Andrew Mendelsohn - Senior Vice President Database Server Technologies came on stage to explain that the next step after I/O optimization for Database with Exadata, was to accelerate the Database at execution level by bringing functions in the SPARC processor silicium. All in all, to process more and more Data... The big theme of the day... and of the Oracle User Groups Conferences that were also happening today and where I had the opportunity to attend some interesting sessions on practical use cases of Big Data one in Finances and Fraud profiling and the other one on practical deployment of Oracle Exalytics for Data Analytics. In conclusion, one picture to try to size Oracle Open World ... and you can understand why, with such a rich content... and this only the first day !

  Read the article

• Monitoring AWS Systems Behind ElasticBeanStalk

  - by A. Avadis

  So I'm getting a company set up in the Amazon Cloud -- creating IAAS protocol/solutions/standardized implementation, etc while also being the SysAdmin for individual systems, app environments, and day-to-day uptime. One of the biggest issues I'm having is tracking various system/application logs, as well as logging/monitoring/archiving system metrics like memory usage, cpu usage, etc etc In a centralized fashion. E.g. -- Nagios + Urchin. The BIGGEST impediment to my endeavors is the following: The company application is deployed in the form of a Java *.WAR file, uploaded to an Elastic BeanStalk application environment, load balancing and auto-scaling between 3(min) and 10(max) servers, and the EC2's that run the application are fired up and disposed of ad-hoc. That is to say, I can't monitor the individual EC2's for very long because so many are being terminated then auto-provisioned/auto-scaled on the fly -- so I'd constantly be having to "monitor what I'm monitoring", and continuously remove/add EC2 machine addresses to my monitoring lists. IS there some sort of way to use monitoring tools like Zabbix or Nagios to monitor the ElasticBeanStalk, and have it automatically add on new EC2's, and remove terminated/failed EC2's from its monitoring list automatically? Furthermore, is there anything I can do with GrayLog to achieve similar results with the aggregation/centralization of my application logs from multiple EC2 instances into ONE consolidated set of logs/events? If not GrayLog, is there ANYTHING LIKE GrayLog that can automatically detect what EC2 members are being added/removed from the environment, and collect the logs from them automatically? Any and all advice or direction is appreciated. Thanks much, and cheers!!

  Read the article

• Creating "save as" functionality to .eml file in AppleScript

  - by unieater

  I'm new to AppleScript and trying to figure out how to save a Mail.app message as an .eml message. Ideally, I would like it to act similar to the Mail menu bar actions, in which it saves the message and the attachments together. The workflow is that you have a selection in Mail, hit a hotkey and the function creates a filename (newFile) for the email to be saved. I just need help with how to save the message to the path (theFolder) in an .eml format. tell application "Mail" set msgs to selection if length of msgs is not 0 then display dialog "Export selected message(s)?" if the button returned of the result is "OK" then set theFolder to choose folder with prompt "Save Exported Messages to..." without invisibles repeat with msg in msgs -- determine date received of msg and put into YYYYMMDD format set msgDate to date received of msg -- parse date SEMversion below using proc pad2() set {year:y, month:m, day:d, hours:h, minutes:min} to (msgDate) set msgDate to ("" & y & my pad2(m as integer) & my pad2(d)) -- assign subject of msg set msgSubject to (subject of msg) -- create filename.eml to be use as title saved set newFile to (msgDate & "_" & msgSubject & ".eml") as Unicode text -- copy mail message to the folder and prepend date-time to file name -- THIS IS WEHRE I AM COMPLETE LOST HOW SAVE THE EMAIL into theFolder end repeat beep 2 display dialog "Done exporting " & length of msgs & " messages." end if -- OK to export msgs end if -- msgs > 0 end tell on pad2(n) return text -2 thru -1 of ("00" & n) end pad2

  Read the article

• AJP Connector Apache-Tomcat with php and java application

  - by Safari

  I have a question about proxy and ajp module. On my machine I have a Apache web server and a Tomcat servlet container. On Tomcat is running a my java webapplication. On Apache I have some services and I can call these in this way: http://myhos/service1 http://myhos/service2 http://myhos/service3 I would configurate a ajp connector to call my tomcat webapplication from Apache. I would somethin as http://myhost to call the Tomcat webapp. So, I configurated my apache in this way..and I have what I wanted: I can use http://myHost to visualize the Tomcat webApp by Apache. <VirtualHost *:80> ProxyRequests off ProxyPreserveHost On ServerAlias myserveralias ErrorLog logs/error.log CustomLog logs/access.log common <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /server-status ! ProxyPass /balancer-manager ! ProxyPass / balancer://mycluster/ stickysession=JSESSIONID nofailover=Off maxattempts=1 <Proxy balancer://mycluster> BalancerMember ajp://myIp:8009 min=10 max=100 route=portale loadfactor=1 ProxySet lbmethod=bytraffic </Proxy> <Location /balancer-manager> SetHandler balancer-manager Order deny,allow Allow from localhost </Location> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent </VirtualHost> But, now I can't use the apache services: If I use http://myhos/service1 I have an error because apache try to search service1 on my tomcatWebApp. Is there a way to fix it?

  Read the article

• Mac OS X Terminal.app Ubuntu 9.10 SSHD and incorrect keyboard mapping

  - by Jesse

  Does anyone have any Idea how to handle this? I can't stand connecting to certain Ubuntu boxes via Mac OS X because of issues with keyboard layout etc. I have set TERM=vt100 and TERM=xterm-color in Ubuntu .bashrc and also in the Terminal.app advanced preferences and nothing seems to fix this issue. Trying to use arrow keys on slim silver keyboard results in ^[[A etc. From Answer OS X 10.6.4 When I try to run /lib/terminfo/x/xterm-color I get permission denied? Maybe this is the issue?! Regular bash login shell. If I sudo often it works. Which leads me to believe the above permissions problem is the cause. Output from stty -a: $ stty -a speed 9600 baud; rows 47; columns 181; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = M-^?; eol2 = M-^?; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 -hupcl -cstopb cread -clocal -crtscts -ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc ixany imaxbel -iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe -echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• CMD/ADB - Autorun script to search, copy, and paste a file from android system to flash drive

  - by Outride

  I've looked around and can't find anything that answers my question. This is my first question, so any tips or thoughts are welcome, as well as an answer :p As explained in title, i want to create a script that launches, finds a file on android phone, copies it, and pastes it to a flash drive. As of right now, it's a mix of multiple tutorials, trial and error, and I'm at a point of giving up. As of right now, I have a flash drive, loaded with three scripts. As follows: Bold = name of file file.bat @echo off :: variables /min SET odrive=%odrive:~0,2% set backupcmd=xcopy /s /c /d /e /h /i /r /y echo off %backupcmd% "C:\Users\Outride\Desktop\kikDatabase.db" "%drive%\all" @echo off cls invisible.vbs CreateObject("Wscript.Shell").Run """" & WScript.Arguments(0) & """", 0, False launch.bat wscript.exe \invisible.vbs file.bat So far, I had to use android commander, manually go through the directory, find /data/data/kik.android/databases and then copy kikDatabase.db to my desktop. Then run this scrip. Yes i'm trying to pull the database to copy all my email contacts. I use launch.bat, which then makes file.bat invisible due to the invisible.vbs script. What would i need to do now to have the file searched for and copied to the flashdrive? Thanks in advance, i'll be glad to answer any questions if theres any :p just remember that i'm not exactly a tech expert haha EDIT* Cleared junk of prior edits. New - I now have a .bat script to recognize what drive the usb is on, and launch py_cmd (adb shell) This is the current script. pull.bat @echo off :: variables SET odrive=%odrive:~0,2% set launching=start "%drive%\Minimal ADB and Fastboot\py_cmd" echo off %launching% so how could I make it for the .bat or a new script, to type the following "adb pull /data/data/kik.android/databases/ %drive%\All\Database" into the adb terminal? please help! I've been racking my brain over this all night :3

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >