Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 142/172 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• Looking for a small, portable, port-mirroring ethernet switch.

  - by user37244

  I recently had a mac go haywire, taking half a minute or more to get www.google.com loaded. Getting its owner to give up the machine for repair was like pulling teeth - they were insisting that it must be something to do with the network, since so much had changed with the local configuration at about the same time their box went haywire. I eventually set up a port mirror to a box that I could remote to so I could show that the mac was only irregularly getting packets onto the network. Demonstrating this faced an additional challenge: the latency of the remote desktop software I was using meant that I had to point to timestamps instead of just the moment the packet flashed up on the screen as my evidence. This particular user was the reason this was so challenging this time around, but I would like to have a box that I can cart from desk to desk to use wireshark on my laptop at any station where I need it. 3com, cisco, netgear, etc. (ad nauseum), all make switches that can be configured for port mirroring, but in my case, the smaller, the better. For the sake of my sanity, I'll probably end up running it off a battery anyway. If my laptop had two ethernet ports, this would be easy. So, whaddya recommand for a device that requires 0 configuration at each powerup (though I'm fine with poking at it for a while to set it up initially.) Small, light, and cheap enough to get it past purchasing? Thanks,

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• Syntax error on line 494 of httpd.conf: Cannot load .../php5apache2_2.dll into server

  - by pikachu

  I have been learning PHP. I had installed Apache-server (not in a combination-suite like USBWebserver). Now I'm trying to put my sites on a portable stick, using USBWebserver. I already used that program before to carry MySQL databases with me (and Apache worked as well, cause I used the included PHPMyAdmin for managing the databases.), but now it doesn't work anymore. When I start the program, I keep having the text saying Apache is offline. I've tried to open Apache using the command line (don't know what that would do, but, it's just a try). I got an error message saying Syntax error on line 494 of C:/.../httpd.conf: Cannot load C:/.../php5apache2_2.dll into server: (The following is translated from Dutch) An initialization routine of the dynamic link library (dll-file) has failed. Line 494 says this: LoadModule php5_module "C:/Users/School/Downloads/USBWebserver v8_en/php/php5apache2_2.dll" My first Apache installation (its service) is not running. The ports are different. And I also uninstalled the service (using the httpd.exe -k uninstall command); What can be the problem? Thanks for help.

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• SNMP closed state in CentOS

  - by anksoWX

  I'm having a problem here, I've added to my IPtables rules this: -A INPUT -p tcp -m state --state NEW -m tcp --dport 161 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 161 -j ACCEPT but when I scan with nmap or any other tool it says this: Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 161/tcp closed snmp also when I am doing: netstat -apn | grep snmpd tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN 3669/snmpd<br> udp 0 0 0.0.0.0:161 0.0.0.0:* 3669/snmpd<br> unix 2 [ ] DGRAM 226186 3669/snmpd Also: service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination 1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:161 5 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:161 6 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 7 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) num target prot opt source destination Any idea what's going on? There is no UDP in closed/open state. what do I have to do?

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Windows Server 2008 - RAID 5 Fails on Reboot

  - by Adam

  Hey, I've got an install of Windows Server 2008 Enterprise. It's running software RAID-5 with five disks. The disks were originally formatted under Windows Server 2003, but came up fine once I installed Windows Server 2008. The issue I'm having is that every time I reboot the server, the RAID comes up with a "Failed Redundancy" - the data stays available. I have 4 disks on a PCI SATA controller, and one of the disks connected to the motherboard's on-board SATA ports. (The other on-board port has the system disk connected.) I was having Disk #4 fail consistently, so I tried swapping the cables on the controller end. I swapped the on-board RAID disk with one on the PCI controller. Same issue now, expect with disk #1. Once the system's up, I can reactivate the RAID, it will resync for a while, then go to "Healthy", and will stay that way for an indefinite amount of time - until I reboot. As soon as I reboot, the disk drops again. I've ruled out disk + cable with the recabling. I don't believe it would be the controller as it seems to work fine most of the time - only failing on reboot, and the other port on the same controller connects the system disk - which is clearly working. I did look in the event log, but didn't see anything particularly relevant (although I didn't know what I was looking for - just looked for anything with a "Warning" or "Error" symbol that looked disk-related :)). I'm not particularly familiar with RAID on Windows, does anyone have any idea why this might be doing this? Any idea how to fix it? Any suggestions appreciated! -- Adam

  Read the article

• Hadoop streaming job on EC2 stays in "pending" state

  - by liamf

  Trying to experiment with Hadoop and Streaming using cloudera distribution CDH3 on Ubuntu. Have valid data in hdfs:// ready for processing. Wrote little streaming mapper in python. When I launch a mapper only job using: hadoop jar /usr/lib/hadoop/contrib/streaming/hadoop-streaming*.jar -file /usr/src/mystuff/mapper.py -mapper /usr/src/mystuff/mapper.py -input /incoming/STBFlow/* -output testOP hadoop duly decides it will use 66 mappers on the cluster to process the data. The testOP directory is created on HDFS. A job_conf.xml file is created. But the job tracker UI at port 50030 never shows the job moving out of "pending" state and nothing else happens. CPU usage stays at zero. (the job is created though) If I give it a single file (instead of the entire directory) as input, same result (except Hadoop decides it needs 2 mappers instead of 66). I also tried using the "dumbo" Python utility and launching jobs using that: same result: permanently pending. So I am missing something basic: could someone help me out with what I should look for? The cluster is on Amazon EC2. Firewall issues maybe: ports are enabled explicitly, case by case, in the cluster security group.

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• XP box with 3 NICs on Server 2003 Domain

  - by Hannibal

  I have assigned all three NICs IP addresses that are outside the DHCP pool. I have 2 NICs are connected to 1 switch and the 3rd to my second switch. I want to assign one of the two NICs on the 1st switch to "normal" network activity (e.g. internet access, RDP, etc.) The other two NICs I want to reserve for mirroring ports on their respective switches. While this machine is connected to the domain I can access the internet and Remote Desktop. I have no idea which NIC I am using until I start mirroring a port, at which time, if I happen to be connected through one of the NICs I have dedicated to mirroring, I lose my remote desktop. I am aware that I would have more control over the NICs using Linux. I want to explore Windows solutions before I go that route because reinstalling another OS would be inconvenient (but not impossible). I would likely use a version of Backtrack (3 or 4 not sure). I would also have to learn how to access the machine remotely but I've done it before so this would be a minor obstacle. Thank you for your assistance.

  Read the article

• How to manage unprivileged administration of system services using Debian?

  - by ypnos

  At our lab, we have several services handled by different phd students (like myself). Fluctuation is high and people do the job next to their research duties. Until now, services were running on different machines, with different OS setups that can result in administration hell quickly. We want to consolidate our service setup. Our main idea is that the guys responsible for the services should not meddle with the underlying system anymore. Apart from core systems like NFS and kerberos, a typical service is able to run as non-root already. I'm talking about apache, mysql, subversion, mail with openxchange, and so on. Redirecting privileged ports is also no issue (source). What is left is the configuration of the service and its payload. One scenario we envisioned is that every service has its own user and home directory, accessable by the corresponding admins. Backup and fallback of the service is easy, as everything needed for the service to run is found in one place. Are there established ways to create such a setup? Does a mostly unique method exist to make services find their files (other than in system directories) while still using the corresponding debian packages? Are there any catches with our idea that we may have overlooked? Would you maybe claim that virtualization is the answer to our problem? (In our POV, it wouldn't help us keeping system setup strictly separated from service setup.) Thank you for any advice!

  Read the article

• Capabilities of business and SOHO routers

  - by Q8Y

  I'm currently studying for the CCNA certifications (especially for Cisco routers and configuration). I know that business routers provide more features than SOHO routers, the processing speed and RAM can be enough. Assume I need to connect a number of users through a network (accessing internet, share files, printers, ...). I have a high speed connection to the internet and I already applied QoS. How can I find out how many users such a single (SOHO) router could handle? In my case I'd attach to it multiple switches until I have the number of ports needed. Would everything work well and smoothly with 50 users? What about 300? At which point would I need a business router instead? If I implemented VLAN here, would it make any difference in the performance? When do I really need to use more than one router? (Both SOHO and business) I'm thinking that I may need them only if I want to increase the performance (instead of replacing the existing one) and if I have multiple locations, so in this situation I need to have multiple routers, right? Put differently: Is there is a need to have another router if my business all in one place?

  Read the article

• Issues Deploying Functional WAR to Elastic Beanstalk with Tomcat7

  - by BFar

  I am currently deploying OpenTripPlanner (http://github.com/OpenPlans/OpenTripPlanner.git) to Elastic Beanstalk. I'm able to successfully build and deploy opentripplanner with my own customized settings on an ec2. I have set it up so that the appropriate WAR file can be placed in the Tomcat/Webapps folder, and when Tomcat is started up, it will auto-deploy, and even download open trip planner's graph.obj from an S3. All of that works just fine, except when I try to deploy to Elastic Beanstalk. When I upload to Elastic Beanstalk, the log shows that my WAR file is successfully unpacked & successfully downloads the graph.obj from my S3. The only difference is that then nothing happens and I can't load the site in my browser. The health is RED, and I can't figure out what is going on. I've tried looking into ports and dns issues, but I can't determine what's wrong. Anyone have any ideas? Why would a WAR that works on tomcat7 outside of Beanstalk fail to be accessible?

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

  Read the article

• PC -> TV HDMI suddenly doesn't work, any other option does

  - by XSlicer

  So my parents wanted to connect their PC to their TV, so they bought a 10m (35 ft) cable. It all worked perfectly. Then my mom tripped over the cable, breaking it. She somehow got a free replacement, but at the same time some more expensive one from an uncle. Now the problem is that this suddenly doesn't work anymore (TV saying "Format not supported"). I've tried several other things to pinpoint the actual problem, but none brought me something conslusive: PC (hdmi) to TV doesn't work (both cables) PC (hdmi) to TV doesn't work (short cable) Laptop (hdmi) to TV work (same cables) BluRay (hdmi) to TV works (same cables) PC (hdmi) to monitor works (same cables) PC (DVI w/ adapter HDMI) to TV works (same cables) I've tried different ports, tried Linux, reinstalling drivers (the graphics card is internal using an i5 sandy bridge. Normally it's running Windows 7 Home Prem, the TV being a Philips 37PFL7605H). So basically, everything works, except that thing what we want. The only things I am thinking of is that the sound is interfering or that the HDMI-output is somehow broken. Or is it anything else? I'm kind of lost.

  Read the article

• Nginx proxy upstream cached?

  - by Julian H. Lam

  Attempting to resolve an issue that's been annoying me for a bit. I've distilled the symptoms into a set of reproducible steps: I have two sites, siteA, and siteB. They are both Node.js applications running on different ports (for the sake of example, 4567 and 4568) Both applications have their own file in sites_available (plus a symlink from sites_enabled), which contain the directives proxy_pass http://node_siteA/ and proxy_pass http://node_siteB/ respectively, inside of a location block. They also each have an upstream block (defined globally?): upstream node_siteA { upstream node_siteB { server 127.0.0.1:4567; server 127.0.0.1:4568; } } Site A and Site B have nothing to do with each other. Yes, I am restarting (reloading, actually) nginx every time I make a change. If I take down site B and attempt to access it via the web, I am served site A. Why is this? Thoughts Other times, when I create a new Site C, for example, nginx refuses to show me anything except "Welcome to nginx!" for ~5 minutes. This suggests a resolver timeout, perhaps? When I access Site B after its config has been deleted, and it sends me to Site A, this sounds like nginx sending me to servers in a round-robin fashion...

  Read the article

• Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

  Read the article

• Computer won't start after installing new video card

  - by Vercas

  So, 1 year and 340 days ago I bought a desktop computer. Since then, it has served me well. But lately, I wanted an upgrade, so I bought a new video card. I documented myself about the compatibility, and it is okay. So I opened the case, cleaned up that... dust elemental living inside of it. Unscrewed the plastic thingie on the outside to unscrew the old video card. Because of the stupid arrangement of the ports, I had to unscrew the motherboard to unplug it. So I unscrewed it, removed the old card, put in the new one, moved the motherboard back, screwed it back in, screwed the video card on the holder... thingie, and screwed the plastic thingie back in. Everything went smoothly, nothing had to be forced in/out. I connected the external power supply, closed the computer case, put the tower back in it's place and all the cables back in. When I pressed the power button, the LED turned... some color I can't distinguish. It stayed that way for a second, and then it went off. I tried a bunch of things, including permuting the external power supply arrangement (1 connection, 2 connections and no connections), with no success. And here are some of the specifications: Motherboard manufacturer: Asrock Processor: AMD Athlon II X2 3.0 GHz RAM: 2 x 2GB (had only 1 initially, bought the second plate a bit later) OLD video card: AMD Radeon HD 5450 NEW video card: Gigabyte nVidia GeForce GTX 650 GPU, 1GB GDDR5 128bit PCI-E, Dual-link DVI-Dx2 / HDMI / D-Sub Power supply: 450W + all the requirements I managed to find on the internet are met (+12V 18A or something) More specific information is stored... On that computer. If required, I may open the case again and read the stickers to find more specific information. I can also provide photos if necessary. Any ideas? Suggestions? Something? :|

  Read the article

• How to prevent eMule from jamming up the router?

  - by the searcher

  Usually, when eMule is started, after some time, I find that the router is jammed, so the internet connection on that computer stopped working, or it seemed to be waiting for some port to be freed up before it can connect to a website. This sometimes affect even other PCs or Macs using the same router. Is there a way to prevent eMule from hogging too much resource or ports? I see that there is under Options -> Connection "Max Sources/File" and a "Connection Limits - Maximum Connections". Right now I set them to really low numbers: the first to 120 and the second to 200, but what are good numbers to fill in there so that it can work well without jamming up the router or use up the network resource of the PC or Mac? Or could it be that the number of files that are "Waiting" is too high, and used up too much resource? (If so, can emule automatically limit the number to 10 or 20 to prevent using too much resource?) (This happened before on Linksys router, Netgear router, and the AT&T U-verse router.)

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >