Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 139/172 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• What is the best way to connect 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• Swapping out a hardware firewall does the mac address get cached?

  - by Dan

  We need to replace a hardware firewall (cisco pix) and have a spare that we will use (temporarily). The firewall sits in front of a couple of web-servers colocated at a data-centre. The replacement will be configured with identical settings (external/internal IP addresses, configured ports etc.). When we swap the firewalls over, will this work immediately or will the old Pix's mac address be cached and the new firewall not be seen until the cache is cleared? (What is it though that is caching the address? Is it just the switch/router that our pix is connected to?) Reason for asking is a few years ago I had a smoothwall firewall in front of a lone server (the external IP of the smoothwall was also the external IP of the web-server). When I replaced the smoothwall with a pix, the IP address of the web-server stayed the same but it now had to be reached via the new firewall on a different IP. It took about 2-4 hours before the rest of the world could see that web-server again. I'm hoping for less downtime this time!

  Read the article

• Win 2003 SBS - secure enough by default?

  - by Pekka

  I have to set up a Windows 2003 Small Business Server to work as a Subversion repository and possibly as an E-Mail server later. The machine is a virtual one, hosted with a hosting company, and freshly initialized. I used the Security Configuration Wizard to deactivate all server roles. After I install Subversion, I will open the necessary ports for the service; in addition, obviously, RDP will stay open so I can remote control the machine. Automatic updates are activated, and I will set up E-Mail notification every time somebody logs on to the server. I'm a programmer and not a professional systems administrator, so I would like to know whether you would regard this a sane and secure setup for a (publicly available) box to host sensitive code and/or E-Mail on. Is there anything in addition I should do to make the machine secure? Is there anything I can do on a long-term basis to keep the machine secure, apart from monitoring the event log (as far as I can make sense out of it), and seeing that any hotfixes are installed properly?

  Read the article

• "Network Error - 53" while trying to mount NFS share in Windows Server 2008 client

  - by Mike B

  CentOS | Windows 2008 I've got a CentOS 5.5 server running nfsd. On the Windows side, I'm running Windows Server 2008 R2 Enterprise. I have the "Files Services" server role enabled and both Client for NFS and Server for NFS are on. I'm able to successfully connect/mount to the CentOS NFS share from other linux systems but am experiencing errors connecting to it from Windows. When I try to connect, I get the following: C:\Users\fooadmin>mount -o anon 10.10.10.10:/share/ z: Network Error - 53 Type 'NET HELPMSG 53' for more information. (IP and share name have been changed to protect the innocent :-) ) Additional information: I've verified low-level network connectivity between the Windows client and the NFS server with telnet (to the NFS on TCP/2049) so I know the port is open. I've further confirmed that inbound and outbound firewall ports are present and enabled. I came across a Microsoft tech note that suggested changing the "Provider Order" so "NFS Network" is above other items like Microsoft Windows Network. I changed this and restarted the NFS client - no luck. I've confirmed that the share folder on the NFS server is readable/writable by all (777) I've tried other variations of the mount command like: mount 10.10.10.10:/share/ z: and mount 10.10.10.10:/share z: and mount -o anon mtype=hard \\10.10.10.10:/share * No luck. As per the command output, I tried typing NET HELPMSG 53 but that doesn't tell me much. Just "The network path was not found". I'm lost on how to proceed with troubleshooting. Any ideas?

  Read the article

• LogMeIn style remote access to NAS drive

  - by Mere Development

  I've been asked to setup some remote access to a NAS drive. The NAS drive will sit on a VLAN inside a network that uses a Cisco 891 IS router as gateway. The charity have no SSL-VPN licenses for the Cisco. At present there are no open ports or services on the Cisco itself and ideally we would like to keep it that way for a while, hence the request for a LogMeIn style service that's initiated from inside. We need multiple user access, about 10 max. Using LogMeIn on a machine connected to the NAS would only provide screen sharing I believe, and no concurrent connections (could be wrong?) The end users need to be able to read and write files to the NAS from Mac's and PC's around the globe. Read-only access from Mobile devices would be a bonus but not absolutely necessary. This is for a charity, non-commercial, but they are willing to spend if necessary. Cisco config knowledge is at a minimum so if I can avoid upsetting that delicate device I'll be happy :) Anyone have any clever ideas? I can provide more information on request. Thanks, Ben

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• hp DL380 G4 won't boot with disk plugged into front USB

  - by Kev

  We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

  Read the article

• python reports socket in use, netstat and others claim its not

  - by captainmish

  We have a strange socket issue with a RHES3 box: Python 2.4.1 (#1, Jul 5 2005, 19:17:11) [GCC 3.2.3 20030502 (Red Hat Linux 3.2.3-52)] Type "help", "copyright", "credits" or "license" for more information. >>> import socket >>> s = socket.socket() >>> s.bind(('localhost',12351)) Traceback (most recent call last): File "<stdin>", line 1, in ? File "<string>", line 1, in bind socket.error: (98, 'Address already in use') This seems normal, lets see what has that socket: # netstat -untap | grep 12351 {no output} # grep 12351 /proc/net/tcp {no output} # lsof | grep 12351 {no output} # fuser -n tcp 12351 {no output, repeating the python test fails again} # nc localhost 12351 {no output} # nmap localhost 12351 {shows port closed} Other high ports work fine (eg 12352 works) Is there something magic about this port? Is there somewhere else I can look? Where does python find out that socket is in use that netstat doesnt know about? Any other way I can find out what/if that socket is?

  Read the article

• Cisco Access switch is dropping large amount of end points

  - by user135458

  This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

  Read the article

• Upstart multiple instances of service not working

  - by Dax

  I started playing with MongoDB on Lucid. Now I would like to run a DB and Config server on the same box. They both use the same binary to launch, but with different config files and running on different ports. All directories for log and lib is split so one goes to mongodb and the other to mongoconf. Each process can be started without any problems on their own. start mongodb stop mongodb start mongoconf stop mongoconf But if I try to start both, the second one would just start and exit. Using 'initctl log-priority debug' I got the following in the logs. Jan 6 12:44:12 mongo4 init: event_finished: Finished started event Jan 6 12:44:12 mongo4 init: job_process_handler: Ignored event 1 (1) for process 5690 Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) main process (5690) terminated with status 1 Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) goal changed from start to stop Jan 6 12:44:12 mongo4 init: mongoconf (mongoconf) state changed from running to stopping man 5 init shows that you can use instance names to differentiate the two. I tried using 'instance mongoconf' in the on upstart script and 'instance mongodb' in the other one, and it still fails. I can manually start the other process, so there is definitely no conflicts on port numbers or directories. Any ideas on what to try or how to get output on why it is 'terminated with status 1'? Thanx

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• Multi-WAN bonding across different media

  - by Tom O'Connor

  I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

  Read the article

• Determining the Source of a Given File System Mount on Unix [migrated]

  - by phobos51594

  Background Recently I have run into a bit of a snag on my home FreeBSD server. I recently upgraded it to the latest stable release, and I have noticed some strange behavior with the /var partition. Originally, I had the system configured such that /var had its own partition with /var/run and /var/log in memory disks (/tmp, too). After the upgrade, I notice there is a new, fourth memory disk mounting directly to /var that I had not set up manually and is not in my fstab. It is only 28 megs or so in size and is causing problems when trying to update my ports collection. The ramdisk mounts atuomagically at boot and cannot be unmounted while in multi-user mode. If I drop to single user mode, I am able to unmount it without issue, however rebooting causes it to pop right back up. System specifications have been included at the end of the post. Question Is there any way to determine exactly what is mounting a given memory disk (or any filesystem, for that matter) after it has been mounted? Alternately, does anybody have any ideas what might have caused the new /var ramdisk to pop up? System Specification # uname -a FreeBSD sarge 9.1-PRERELEASE FreeBSD 9.1-PRERELEASE #0: Thu Nov 22 14:02:13 PST 2012 donut@sarge:/usr/obj/usr/src/sys/GENERIC i386 # df Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/da0s1a 515612 410728 63636 87% / devfs 1 1 0 100% /dev /dev/da0s1d 515612 287616 186748 61% /var /dev/da0s1e 6667808 2292824 3841560 37% /usr /dev/md0 63004 32 57932 0% /tmp /dev/md1 3484 8 3200 0% /var/run /dev/md2 31260 8 28752 0% /var/log /dev/md3 31260 512 28248 2% /var <-- This # cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/da0s1a / ufs rw,noatime 1 1 /dev/da0s1d /var ufs rw,noatime 2 2 /dev/da0s1e /usr ufs rw,noatime 2 2 md /tmp mfs rw,-s64M,noatime 0 0 md /var/run mfs rw,-s4M,noatime 0 0 md /var/log mfs rw,-s32M,noatime 0 0 Thank you in advance for any assistance.

  Read the article

• linux: mount old ATA disk to USB adapter

  - by 130490868091234

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

  Read the article

• New SSD, is the MBR broken? DISK BOOT FAILURE

  - by Shevek

  I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

  Read the article

• Suddenly can't send E-Mails with Apple Mail to Gmail SMTP

  - by slhck

  Hi all, I have a weird problem that started just today. I am using Apple Mail on a Leopard machine, connecting to Gmail. Fetching e-mail works just fine. My SMTP settings are also correct. Still, I can't send mail, it will display a pop up saying that "transferring the content to the mail server" failed (translation from German, could be different in English OS X versions). I have verified the following: My SMTP settings are definitely correct. I have not changed them and the issue appeared today. Also, I went through the Apple online configuration for Gmail accounts and did not have to adjust any setting. I can run network diagnosis and it will connect to both POP and SMTP servers without a problem (all green lights) The Telnet details will show me the HELO message from the Gmail servers, so there's no authentication failure. Console.app will not show any messages related to "mail" when I try to send the mail, so there's no specific error message The mail I'm trying to send does not have an attachment, it is plaintext only I can login to gmail.com and send mails without a problem The recipient address exists and contains no syntax errors I can also not send mails to myself When using another IP and ISP (through VPN), it still doesn't work As for my settings: I connect to smtp.gmail.com and for advanced settings I choose password-based authentication with user: [email protected] and my password. I let Apple Mail try the default ports (for SSL and TLS, respectively). Again: I have not changed a thing between yesterday and today. What is causing that strange behavior? Any help would be much appreciated.

  Read the article

• Port 5357 TCP on Windows 7 professional 64 bit?

  - by Registered

  Is there a reason this port is open, a quick Nmap scan and Nessus scan reveal it's open, why? Are there any ramifications if I close this port via the firewall rule set? Or does anyone here now more info about this port besides Google? WTF? 1)http://www.symantec.com/connect/blogs/who-left-tunnel-door-open-windows-firewall-vista-0 I know the talk is about Vista, but I am pretty sure it's the same port on 7, also. 2)Port 5357 common errors:The port is vulnerable to info leak problems allowing it to be accessed remotely by malicious authors. (Web Services for Devices) I am blocking this crap, if I have issues will just re-enable. Damn windows. Inbound rule for Network Discovery to allow WSDAPI Events via Function Discovery. [TCP 5357] You just got blocked, until I break something, will see. Time to re-Nmap and re-Nessus. Nmap scan 0 open ports after closing Port 5357,Win7 still works for now, one more scan with Nessus just to make sure all is well.

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• What program sent which packet to the network [closed]

  - by Erik Johansson

  I would like to have a tcpdump like program that shows which program sent a specific packet, instead of just getting the port number. This is a generic problem I've had on and off sometimes when you have and old tcpdump file lying around you have no way to find what program was sending that data.. The solution in how i can identify which process is making UDP traffic on linux ? is an indication that I can solve this with auditd, dTrace, OProfile or SystemTap, but doesn't show how to do it. I.e. it doesn't show the source port of the program calling bind().. The problem I had was strange UDP packets, and since those ports are so short lived it took me a while to solve this issue. I solved this by running an ugly hack similar to: while true; date +%s.%N;netstat -panut;done So either a method better than this hack, a replacement for tcpdump, or some way to get this info from the kernel so I can patch tcpdump. EDIT: This was asked on superuser "tracking what programs sends to net", no good solution though.

  Read the article

• Torrent upload ratio not updated on Synology DS212+

  - by user179271

  I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

  Read the article

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >