Search Results

Search found 41582 results on 1664 pages for 'fault tolerance'.

Page 148/1664 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• Windows Server 2008 x86 Services for Unix SDK (SUA) RSH

  - by Andy Arismendi

  Running RSH commands on a Windows box against a Linux box works only for the administrator user. Is there a file somewhere that has a list of users that can run commands remotely? More Info The server configuration is automated by VMware's product... There's no /etc/hosts.equiv file setup but there is a /root/.rhosts file with an entry of [IP ADDRESS] +. The SUA client C:\Windows\SUA\bin\rsh can login when run as the local administrator account but no other user can login. The error is: rcmd: unknown user: [username]. The command I'm trying to run is: rsh -l root [IP ADDRESS] ls.

  Read the article

• Nginx + uWSGI on a fresh Ubuntu install - bind error port 80

  - by knuckfubuck

  I know this is a common problem usually having to do with apache or another service already running on port 80 and I have done a lot of searching and running netstat and still have not figured out why I am getting this error. I rebuilt my slice, did a fresh install of Ubuntu 10.04 and setup nginx + uwsgi. It worked and I was able to see my Django site. I then installed Postgres8.4 and the rest of the stack needed for Geodjango from this link. After that was done I tried to restart nginx and I get this error: sudo /etc/init.d/nginx start Starting nginx: the configuration file /usr/local/nginx/conf/nginx.conf syntax is ok configuration file /usr/local/nginx/conf/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() I have nginx set to listen 80. Here's an output from netstat -l --numeric-ports | grep 80: tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:8000 0.0.0.0:* LISTEN Output from sudo lsof +M -i4: nginx 2330 root 8u IPv4 3195 0t0 TCP *:www (LISTEN) nginx 2331 www-data 8u IPv4 3195 0t0 TCP *:www (LISTEN) uwsgi 2335 s 4u IPv4 3259 0t0 TCP localhost:8000 (LISTEN) uwsgi 2352 s 4u IPv4 3259 0t0 TCP localhost:8000 (LISTEN) uwsgi 2353 s 4u IPv4 3259 0t0 TCP localhost:8000 (LISTEN) uwsgi 2354 s 4u IPv4 3259 0t0 TCP localhost:8000 (LISTEN) uwsgi 2355 s 4u IPv4 3259 0t0 TCP localhost:8000 (LISTEN) Anyone have any other ideas how I can figure out what is blocking port 80? edit Paste of my /etc/init.d/nginx script here: http://dpaste.com/hold/400937/

  Read the article

• Request time out error

  - by Neo

  Hi Today i came across strange problem whenever i try to pinging to my server works properly but whenever i send http request from browser the request time out happens. can anybody help me to resolve this issue.

  Read the article

• SBS2003 OWA not displaying images on external side

  - by JasonC

  I've got an SBS 2003 server with companyweb/remote owa site. After authenticating remotely to the https:/servername/remote site, and then clicking on Use Outlook Web Access, the mail/owa site displays only limited amounts of data with Loading... displayed (see first image). This is different when viewing the site on the server itself (see second image). Different browsers will display different types of data (last screenshot is Chrome - first two are IE). I feel IIS permissions on the virtual directories is the cause, but not certain. Forms-based authentication etc is working ok etc. Any suggestions? Authentication and getting email via ActiveSync is not a problem. I don't want to break anything, and it's not a major problem because the users only get their email via outlook and iphones anyway without problems. I'm more interested in finding out for my own info so please give me some suggestions to try. Thanks for looking!

  Read the article

• mysql: unrecognized service ... but mysql is installed and it's working

  - by mojtaba zavar

  I'm trying to stop mysql and do some changes , then i'm going to start it again I'm using a SSH client . So i ran this 3 commends without any problem mysql mysql> SET GLOBAL innodb_fast_shutdown = 0; exit; now when i type service mysql stop or service mysql i get mysql: unrecognized service whats wrong ? my site is online and it's using mysql database as i'm typing this , but i can't access service mysql some extra info CentOS release 6.4 (Final) Server version: 5.5.31 MySQL Community Server

  Read the article

• Why RSA SSH authentication only works after console log-in?

  - by smorhaim

  I setup RSA authentication on one of my Ubuntu servers, however after every restart, I can't log-in via ssh RSA. In order to log-in with ssh I need to first log-in via console, then the RSA starts working. Why??? Below are my sshd config file as well as an output from the ssh -vv command before console log-in and after. . Before console log-in: debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /Users/smorhaim/.ssh/smorhaim (0x7ff8d8c242c0) debug2: key: /Users/smorhaim/.ssh/id_rsaadmin (0x7ff8d8c24cf0) debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/smorhaim/.ssh/smorhaim debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey debug1: Offering RSA public key: /Users/smorhaim/.ssh/id_rsaadmin debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey debug2: we did not send a packet, disable method debug1: No more authentication methods to try. Permission denied (publickey). After console log-in: debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /Users/smorhaim/.ssh/smorhaim (0x7f91c14242c0) debug2: key: /Users/smorhaim/.ssh/id_rsaadmin (0x7f91c1424ae0) debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/smorhaim/.ssh/smorhaim debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 279 debug2: input_userauth_pk_ok: fp b1:d5:90:43:be:43:52:a9:7f:05:c7:04:86:57:b3:ff debug1: Authentication succeeded (publickey). Authenticated to 10.10.30.151 ([10.10.30.151]:22). sshd config: Port 22 Protocol 2 ListenAddress 10.10.30.151 UsePrivilegeSeparation yes SyslogFacility AUTHPRIV PermitRootLogin no PasswordAuthentication no ChallengeResponseAuthentication no UsePAM yes X11Forwarding yes

  Read the article

• MySQL Replication Error

  - by Ian

  I recently updated my master server to 5.1.41 and noticed that the slave was no longer replicating. It was returning this erorr: 091208 12:53:31 [ERROR] Slave I/O: error connecting to master '[email protected]:3306' - retry-time: 10 retries: 86400, Error_code: 2026 091208 12:53:41 [ERROR] Slave I/O: error connecting to master '[email protected]:3306' - retry-time: 10 retries: 86400, Error_code: 1045 The first error is apparently an SSL error, followed by auth denied.. Thing is, I haven't touched my SSL key or user access in months (and the key is fine, since I'm using the same one on that machine to replicate from other master servers.. Any ideas? Edit: Months later, I've tried with 5.1.44 and the problem is persisting. When I roll back to 5.1.39 replication works great... I guess I can't use anything newer than 5.1.39....

  Read the article

• Cisco PIX 515 internet connection

  - by Steve

  We have a ASDL modem connected to a Cisco PIX 515 to a switch. We have managed to get the PIX setup with ethernet1 (inside) with our IP range 192.168.5.1-192.168.5.254 and the internal network is working fine. We are having difficulty getting a connection from the PIX through the router on ethernet0 (outside). We have managed to ping external networks by setting up IMCP echo/echo-reply but are unable to setup any other protocols in a similar manner. Can any one help with a few lines that could be typed into the console that will allow this connection?

  Read the article

• PXE boot and DHCP server configuration Failing Auto Installation

  - by Harihara Vinayakaram

  I have a ISC DHCP Server installed on Ubuntu 9.10 . I have managed to successfully boot a PXE client , obtain a DHCP address and load the initrd.gz file. But I am facing a vague problem when the debian installer starts up and tries to get a DHCP server The client send a DHCP request and I verified that is the same MAC Address. But I get a DHCP DECLINE (The client declines the address ). It offers all the address in the pool and then there is a DHCP NAK (no more free leases ) I tried using the Option no-ping, and also option one-client-one-lease but it does not help . If I set the client to use a fixed-address then the above problem is not there and the installation proceeds smoothly Can you give me any clues on what should be the DHCP server configuration My dhcpd.conf looks like this { ddns-update-style none; option domain-name "hadoop-myorg.org"; option domain-name-servers 192.168.3.5; default-lease-time 600; max-lease-time 7200; group { filename "pxelinux.0"; next-server 192.168.13.184; host hadoop1 { hardware ethernet 90:e6:ba:d5:53:f8; } } subnet 192.168.13.0 netmask 255.255.255.0 { option routers 10.0.0.254; pool { option domain-name-servers 192.168.3.5; max-lease-time 3000; range 192.168.13.55 192.168.13.65; deny unknown-clients; } } }

  Read the article

• Drupal install and permissions

  - by Richard

  So I'm really stuck on this issue. An install process is complaining about write permission on settings.php and sites/default/files/. However, I've moved these files temporarily to write/read (chmod 777) and changed the owner/group to "apache" as shown below. -bash-4.1$ ls -hal total 28K drwxrwxrwx. 3 richard richard 4.0K Aug 23 15:03 . drwxr-xr-x. 4 richard richard 4.0K Aug 18 14:20 .. -rwxrwxrwx. 1 apache apache 9.3K Mar 23 16:34 default.settings.php drwxrwxrwx. 2 apache apache 4.0K Aug 23 15:03 files -rwxrwxrwx. 1 apache apache 0 Aug 23 15:03 settings.php However, the install is still complaining about write permissions. I followed steps one and two of the INSTALL.txt but no luck. Update: To further explore the situation, I created sites/default/richard.php with the following code: <?php error_reporting(E_ALL); ini_set('display_errors', '1'); mkdir('files'); print("<hr> User is "); passthru("whoami"); passthru("pwd"); ?> Run from the command line (under user "richard"), no problem. The folder is created everything is a go. Run from the web, I get the following: Warning: mkdir(): Permission denied in /var/www/html/sites/default/richard.php on line 9 User is apache /var/www/html/sites/default Update 2: Safe mode appears to be off... -bash-4.1$ cat /etc/php.ini | grep safe | grep mode | grep -v \; safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH sql.safe_mode = Off

  Read the article

• Can you authenticate into SSAS with AD LDS (ADAM) accounts?

  - by Jaxidian

  I'm very new to AD LDS and experienced but not qualified with SSAS, so my apologies for my ignorances with these. We have a couple implementations where we expose SSAS via an HTTPS proxy (msmdpump.dll) and currently we have a temporary domain setup handling this (where our end-users have a second account+creds to manage because of this = non-ideal). I want to move us towards a more permanent solution which I'm thinking of moving all authentication to AD LDS for our web apps, SSAS, and others. However, SSAS is where I'm concerned about this. I know SSAS requires Windows Authentication and to play nicely, and that this ultimately means Active Directory will be involved. Is there a way to get this done with AD LDS instead of having to use a full AD DS implementation? If so, how? (Note: My question over at StackOverflow had a suggestion that I post this question here on ServerFault instead. My apologies if I'm not asking in the right forum.)

  Read the article

• Can I have different ESX hosts accessing the same LUN over different protocols?

  - by Kevin Kuphal

  I currently have a cluster of two ESX 3.5U2 servers connected directly via FiberChannel to a NetApp 3020 cluster. These hosts mount four VMFS LUNs for virtual machine storage. Currently these LUNs are only made available via our FiberChannel initator in the Netapp configuration If I were to add an ESXi host to the cluster for internal IT use can I: Make the same VMFS LUNs available via the iSCSI initiator on the Netapp Connect this ESXi host to those LUNs via iSCSI Do all of this while the existing two ESX hosts are connected to those LUNs via FiberChannel Does anyone have experience with this type of mixed protocol environment, specifically with Netapp?

  Read the article

• One Linux server has two timer

  - by garconcn

  The time on one of our Linux box is very weird. Whenever I call date 3 times, the 4th call will give a wrong time(usually 1 hour later). I have setup cron to sync with ntp server. We have 20+ similar servers, only this one has this problem. Any idea? Thanks. Linux 2.6.18-6-686 #1 SMP Thu Aug 20 21:56:59 UTC 2009 i686 GNU/Linux :~# date Fri Jun 11 17:00:51 PDT 2010 :~# date Fri Jun 11 17:00:52 PDT 2010 :~# date Fri Jun 11 17:00:53 PDT 2010 :~# date Fri Jun 11 18:14:12 PDT 2010 :~# date Fri Jun 11 17:00:55 PDT 2010 :~# date Fri Jun 11 17:00:56 PDT 2010 :~# date Fri Jun 11 17:00:56 PDT 2010 :~# date Fri Jun 11 18:14:15 PDT 2010 :~# date Fri Jun 11 17:00:58 PDT 2010 :~# date Fri Jun 11 17:00:58 PDT 2010 :~# date Fri Jun 11 17:00:59 PDT 2010 :~# date Fri Jun 11 18:14:18 PDT 2010 :~# date Fri Jun 11 17:01:01 PDT 2010 :~# date Fri Jun 11 17:01:01 PDT 2010 :~# date Fri Jun 11 17:01:02 PDT 2010 :~# date Fri Jun 11 18:14:21 PDT 2010 :~# date Fri Jun 11 17:01:03 PDT 2010 :~# date Fri Jun 11 17:01:04 PDT 2010 :~# date Fri Jun 11 17:01:05 PDT 2010

  Read the article

• How to move linux executables to a ramdisk?

  - by alfa64

  i've made a ramdisk this way: mkdir -p /media/ramdisk mount -t tmpfs -o size=512M tmpfs /media/ramdisk/ The reason for this is because i run a lot of node.js scripts and their execution time is very small, but i suspect that the time overhead is because it reloads the node.js executable from disk and destroys it on each subsecuent run. So i think this might be the solution to gain a bit, if not much, performance. How can i move a program like node to the ramdisk and run it from there? The idea is to have a startup script that creates the ramdisk and puts the node files inside of it. Note that i'm currently using fedora 16 for what's it's worth. Thanks in advance.

  Read the article

• Entering BIOs Setup from Supermicro IPMI KVM

  - by Joshua Lim

  I'm having trouble getting into BIOs Setup from Supermicro IPMI "KVM" - Remote Control Console Redirection. I need to change the boot order to CDROM first. I'm running Windows 2008 server. After some Googling, it says here that the method is to: Press TAB to enter Setup screen. Press Esc twice to take effect. http://www.supermicro.com/support/faqs/faq.cfm?faq=6222 A month ago, I tried that 30-40 times + DEL, over 2 hours, it worked. Now, I've been trying the same key combination for more than an hour, rebooting each time it failed, it still doesn't work. Note: I've only got a notebook computer, no extra monitor.

  Read the article

• Sonicwall routing between multiple subnets on multiple interfaces

  - by Rain

  As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

  Read the article

• windows server 2003 R2 64bit not seeing more than 4gb ram

  - by Mo

  shouldn't win 2003 R2 64bit see more than 4gb by default or am I missing a setting somewhere? hardware is SuperMicro X6DVA-EG. http://msdn.mzicrosoft.com/en-us/library/aa366778%28VS.85%29.aspx#physical_memory_limits_windows_server_2003

  Read the article

• Supplementary Developer Laptop

  - by David Smith

  I'm looking to buy a laptop with the following specs for a developer. The goal will be to have a development machine supplementing the devs desktop. During work hours the dev will be on a beefy desktop. For working while on the go: trains, client sites, code camps, it would be nice to have a machine which can run Visual Studio 2008 without needing to remote desktop into their primary machine. What do you think is the lowest cost laptop meeting this need? Here are the specs I have in mind: SSD drive 64GB-doesn't need to be huge, most data is stored on servers. Will need to fit Windows 7, IIS, SQL Server, and Visual Studio 2010. RAM-3GB processor =Pentium Core 2 duo Screen size = 14 inches. OS doesn't matter. It will be paved with Windows 7 Ultimate optical drive omitted would be a plus. weight and battery life aren't so important because the machine will be plugged in almost all the time.

  Read the article

• Mod_Proxy_AJP set up issues

  - by TripWired

  I'm trying to set up Tomcat behind Apache using mod_proxy_ajp. After tons of messing around with the configs I am stuck at a 403 page when trying to access tomcat. I had a 404 before but apparently something I changed along the way fixed that. I'm not sure which setting to change at this point. Could anyone look over the configs I have and see if anything is missing. httpd.conf <IfModule mod_proxy.c> ProxyRequests Off <Proxy *> Order deny,allow Deny from all Allow from localhost </Proxy> proxy_ajp.conf LoadModule proxy_ajp_module modules/mod_proxy_ajp.so # # When loaded, the mod_proxy_ajp module adds support for # proxying to an AJP/1.3 backend server (such as Tomcat). # To proxy to an AJP backend, use the "ajp://" URI scheme; # Tomcat is configured to listen on port 8009 for AJP requests # by default. # # # Uncomment the following lines to serve the ROOT webapp # under the /tomcat/ location, and the jsp-examples webapp # under the /examples/ location. # ProxyPass /tomcat ajp://127.0.0.1:8009/ ProxyPassReverse /tomcat ajp://127.0.0.1:8009/ ProxyPass /examples/ ajp://localhost:8009/jsp-examples/

  Read the article

• Import a bunch of certificates into the correct certificate store using a script

  - by Jesse Weigert

  I have a collection of certificates in a p7b file, and I would like to automatically import each certificate into the correct store depending on the certificate template. What is the best way to do this with a script? I tried using certutil -addstore root Certificate.p7b, and that will correctly place all of the root CAs into the root store, but it returns an error if it encounters any other type of certificate. I'm willing to use batch scripts, vbscript or powershell to accomplish this task. Thanks!

  Read the article

• SQL Server (2012 Enterprise) Browser service failing

  - by Watki02

  SQL Server (2012 Enterprise) Browser service failing I have a problem as described below: I have an instance of SQL Server 2012 Enterprise (thanks to MSDN) for local development on my PC. I try to start SQL server Browser Service from SQL Server Configuration Manager and it takes a long time to fail, then fails with: The request failed or the service did not respond in a timely fashion. Consult the event log or other applicable error logs for details. I checked event logs and found these errors in this order (all within the same 1-second time frame): The SQL Server Browser service port is unavailable for listening, or invalid. The SQL Server Browser service was unable to establish SQL instance and connectivity discovery. The SQL Server Browser is enabling SQL instance and connectivity discovery support. The SQL Server Browser service was unable to establish Analysis Services discovery. The SQL Server Browser service has started. The SQL Server Browser service has shutdown. I checked firewall rules and both port 1433 (TCP) and 1434 (UDP) are wide open, just as well - the programs and service binary had been "allowed through windows firewall". I started the "Analysis Services" service by hand and it works fine. Browser still won't start. Some History: Installed SQL 2008 R2 express advanced Installed SQL2012 Express advanced Uninstalled SQL 2008 R2 express advanced Installed 2012 SSDT and lots of features with Express install Installed a unique instance of SQL 2012 Enterprise with all features Uninstalled SSDT and reinstalled SSDT with Enterprise (solved a different problem) Uninstalled SQL 2012 Express Uninstalled SQL 2012 Enterprise Removed anything with "SQL" in the name from Control panel "Programs and features" Installed SQL 2012 Enterprise without Analysis services (This is where I noticed SQL Browser service was failing to start even on the install) Added the feature of Analysis Services (and everything else) via the installer (Browser continued to fail to start on the install) ======================== Other interesting facts: opening a command window with administrator and trying to run sqlbrowser.exe manually yielded: Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Windows\system32cd C:\Program Files (x86)\Microsoft SQL Server\90\Shared C:\Program Files (x86)\Microsoft SQL Server\90\Sharedsqlbrowser.exe -c SQLBrowser: starting up in console mode SQLBrowser: starting up SSRP redirection service SQLBrowser: failed starting SSRP redirection services -- shutting down. SQLBrowser: starting up OLAP redirection service SQLBrowser: Stopping the OLAP redirector C:\Program Files (x86)\Microsoft SQL Server\90\Shared As I try to repair the install it errors out saying The following error has occurred: Service 'SQLBrowser' start request failed. Click 'Retry' to retry the failed action, or click 'Cancel' to cancel this action and continue setup. For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft%20SQL%20Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=11.0.2100.60&EvtType=0x4F9BEA51%25400xD3BEBD98%25401211%25401 Clicking retry fails every time. When clicking cancel I get: The following error has occurred: SQL Server Browser configuration for feature 'SQL_Browser_Redist_SqlBrowser_Cpu32' was cancelled by user after a previous installation failure. The last attempted step: Starting the SQL Server Browser service 'SQLBrowser', and waiting for up to '900' seconds for the process to complete. . For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft%20SQL%20Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=11.0.2100.60&EvtType=0x4F9BEA51%25400xD3BEBD98%25401211%25401 When I go to uninstall the SQL Browser from "Programs and Features", it complains: Error opening installation log file. Verify that the specified log file location exists and is writable. Is there any way I can fix this short of re-imaging my computer and reinstalling from scratch? A possible approach would be to somehow really uninstall everything and delete all files related to SQL... is that a good idea, and how do I do that?

  Read the article

• Installing rpm module of Python for yum

  - by vito

  I've installed Python and yum from source (configure, make, make install), not using RPMs because that's leading to several other issues. So when I executed: # yum update ... I get the following error: Traceback (most recent call last): File "/usr/bin/yum", line 22, in <module> import yummain File "/usr/share/yum/yummain.py", line 22, in <module> import clientStuff File "/usr/share/yum/clientStuff.py", line 18, in <module> import rpm ImportError: No module named rpm Now because I've installed yum and python from source, do I need to install Python's rpm module from source, too? Because installing the rpm for this module lead to the following error: # rpm -vih rpm-python-3.0.4-6x.i386.rpm warning: rpm-python-3.0.4-6x.i386.rpm: V3 DSA signature: NOKEY, key ID db42a60e error: Failed dependencies: python >= 1.5.2 is needed by rpm-python-3.0.4-6x.i386 libbz2.so.0 is needed by rpm-python-3.0.4-6x.i386 librpm.so.0 is needed by rpm-python-3.0.4-6x.i386 Suggested resolutions: /var/spool/up2datepython-2.3.4-14.7.el4.x86_64.rpm I tried searching for the source of this module, but I couldn't find it. Any help in installing this module is appreciated. Thanks for your time. Other info: # python -V Python 2.6.5

  Read the article

• Recovering a VHD after resizing it using VBoxManage

  - by tjrobinson

  I am using VirtualBox 4.1.18 and had a virtual machine running Windows 8 RC with a single VHD, which was initially sized at 25GB (too small!). After installing the OS and some applications I ran out of disk space so shut down the guest and then used this command to resize the VHD to 80GB: C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe modifyhd "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" --resize 81920 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe showhdinfo "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" UUID: 03fb26e7-d8bb-49b5-8cc2-1dc350750e64 Accessible: yes Logical size: 81920 MBytes Current size on disk: 24954 MBytes Type: normal (base) Storage format: VHD Format variant: dynamic default In use by VMs: Windows 8 RC (UUID: a6e6aa57-2d3a-421b-8042-7aae566e3e0b) Location: D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd So far so good. However, when I started the guest up again I got the dreaded: Fatal: No bootable medium found! system halted If I boot into GParted it shows a single 80GB drive as "unallocated". The option to scan for and attempt to repair a filesystem doesn't find anything. I also tried cloning the VHD into a VDI file, just in case that magically fixed it: C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe clonehd "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi" --format VDI 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% Clone hard disk created in format 'VDI'. UUID: baf0c2c4-362f-4f6c-846a-37bb1ffc027b C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe showhdinfo "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi" UUID: baf0c2c4-362f-4f6c-846a-37bb1ffc027b Accessible: yes Logical size: 81920 MBytes Current size on disk: 24798 MBytes Type: normal (base) Storage format: VDI Format variant: dynamic default In use by VMs: Windows 8 RC (UUID: a6e6aa57-2d3a-421b-8042-7aae566e3e0b) Location: D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi Is there anything else I could try to recover the drive? No, I don't have a backup :( My host OS is Windows 7 64-bit.

  Read the article

• which web performance monitoring service is best?

  - by colinguo

  which web performance monitoring service is best? internetvista.com? watchmouse.com?

  Read the article

• CentOS 5.5 ext4 conversion problem - ext4 partition is recognized as ext3

  - by FractalizeR

  Hello. I had 5.4 machine. Upgraded to 5.5 today via yum upgrade. All went fine. Rebooted. Wanted to convert root partition to ext4 (I have three partitions: /boot, / and swap). All of them on software RAID 1 (root is /dev/md2). I did the following for converting yum install e4fsprogs tune2fs -O extents,uninit_bg,dir_index /dev/md2 nano /etc/fstab # I indicated here that my /dev/md2 is of ext4 uname -a mkinitrd -f /boot/initrd-2.6.18-194.3.1.el5.img 2.6.18-194.3.1.el5 Rebooted. I expected fsck to start automatically as said on some site. But it did not. Threw some error (don't remember exactly which). Ok, I booted linux rescue and executed fsck: fsck -t ext4 -fy /dev/md2 Partition went fine. But still when I boot main system, it says in log: "ext3-fs:" then something about not being able to mount ext3 partition due to unknown extended attributed (200). I booted linux rescue again. It loads fine and correctly determines all my machine partitions both ext3 (boot) and ext4 (/) under /mnt/sysimage just fine. I retried mkinitrd thing again watching it's output and ensured ext4 module is included into the system. I also edited menu.lst grub file to include rootfstype=ext4 kernel parameter. Bad luck. I still have message from ext3-fs about not being able to mount filesystem because of attributes and kernel panic immediately after. I checked /etc/fstab - it's fine and saying that root is of ext4. What did I do wrong? This machine is empty so I can just reformat it with 5.5 and recreate partitions to be originally ext4. But... I just want to know what did I do wrong.

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >