Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 154/433 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• Very low throughput on 10GbE network

  - by aix

  I have two Linux machines, each equipped with a Solarflare SFN5122F 10GbE NIC. The two NICs are connected together with an SFP+ Direct Attach cable. I am using netperf to measure TCP throughput between the two machines. On one box, I run: netserver and on the other: netperf -t TCP_STREAM -H 192.168.x.x -- -m 32768 I get: MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.x.x (192.168.x.x) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 32768 10.02 1321.34 The measured throughput is 1.3Gb/s. This is 7.5x below the theoretical maximum, and only 30% faster than 1GbE. What steps can I take to troubleshoot this?

  Read the article

• BT socket Device over Structured Cabling

  - by TheD

  Not sure if this is the right stack* site to post on but I believe cabling is a just subject. Essentially I have a Credit Card machine which is connected to a phone line via standard BT Socket. So basically, the port of the wall has a balun plugged in which takes the RJ45 outlet on the wall to BT, so I can plug the device in. This works fine, however I need the machine to be on the other side of the room so want to route it through my patch panel (strucutered cabling). How can this be done? So Device -- ? -- RJ45 port -- Patch Panel -- ? -- Balun out wall outlet Where ? is to be filled in ! :)

  Read the article

• Custom DHCP Server on home network

  - by DanSpd

  Hello I have a computer network at my house which consists of two computers and one server. I have a software on dedicated server which requires direct connection to internet (port forwarding doesn't work for this). So I plan to setup network in following way. link text Please let me know if this will work. How good or bad could this be? Internet Connection: Verizon Fios 25/25

  Read the article

• Custom DHCP Server on home network

  - by DanSpd

  Hello I have a computer network at my house which consists of two computers and one server. I have a software on dedicated server which requires direct connection to internet (port forwarding doesn't work for this). So I plan to setup network in following way. link text Please let me know if this will work. How good or bad could this be? Internet Connection: Verizon Fios 25/25

  Read the article

• 7-zip for linux

  - by flybywire

  7-zip for linux, does such a thing exist? I mean actually 7-zip or a port, not another compression tool or command

  Read the article

• Achieving/maxing out 1GBPS connectivity on a nginx server

  - by Ansell Cruz

  This page (http://www.remsys.com/nginx-on-1gbps) claims that it can max out a 1gbps line using JBOD setup and no raid. Currently I'm on a 1gbps dedicated port and I'm on raid 10 (4x2TB - the disks that comes with 100tb.com servers). Currently I'm only peaking at 500-550mbps. wa% would show something around 20% everytime. I'm looking into maxing out this 1gbps port because I have an unmetered service from them. Do you guys think that the page that I referenced would be better than my current raid setup? Do you guys have any other suggestions on how to max out the performance of this server? TYI.

  Read the article

• Localhost working fine with executing php code except mail function.

  - by Radheshyam Nayak

  i tried executing the mail() and got the following error "Warning: mail() [function.mail]: Failed to connect to mailserver at "localhost" port 25, verify your "SMTP" and "smtp_port" setting in php.ini or use ini_set() " but SMTP and smtp_port are both set in php.ini more ever other codes are working fine with localhost. disabled or/and added exception to firewell no result.... tried telnet localhost 25 error:could not connect to localhost port 25:connection failed..... Thunderbird my mail client says:could not connect to server localhost the connection was refused.... php.ini [mail function] ; For Win32 only. ; http://php.net/smtp SMTP = localhost smtp_port = 25 running mercury mail server in xampp... previously working fine but now not working..

  Read the article

• firehol (firewall) with bridge: how to filter

  - by Leon

  I have two interfaces: eth0 (public address) and lxcbr0 with 10.0.3.1. I have a LXC guest running with ip 10.0.3.10 This is my firehol config: version 5 trusted_ips=`/usr/local/bin/strip_comments /etc/firehol/trusted_ips` trusted_servers=`/usr/local/bin/strip_comments /etc/firehol/trusted_servers` blacklist full `/usr/local/bin/strip_comments /etc/firehol/blacklist` interface lxcbr0 virtual policy return server "dhcp dns" accept router virtual2internet inface lxcbr0 outface eth0 masquerade route all accept interface any world protection strong #Outgoing these protocols are allowed to everywhere client "smtp pop3 dns ntp mysql icmp" accept #These (incoming) services are available to everyone server "http https smtp ftp imap imaps pop3 pop3s passiveftp" accept #Outgoing, these protocols are only allowed to known servers client "http https webcache ftp ssh pyzor razor" accept dst "${trusted_servers}" On my host I can connect only to "trusted servers" on port 80. In my guest I can connect to port 80 on every host. I assumed that firehol would block that. Is there something I can add/change so that my guest(s) inherit the rules of the eth0 interface?

  Read the article

• Connecting both WAN and LAN ports to the same hub

  - by C. Lee

  For some reason I wish to connect the WAN port and the LAN port on a router to the same hub and make the hub is connected to both networks, the Internet and a private network. Below is a diagram of the network configuration I'd like to build. I tried this and it didn't work as expected. PC 1 has no problem, but PC 2 cannot connect to the Internet. When I ping 192.168.0.1 from PC 2, all packets are lost. It works well when PC 2 is connected directly to the router. What's the problem with the network configuration above?

  Read the article

• SQL 2008 R2 Named Instance Client Connectivity Issues?

  - by Jerry Dodge

  We're upgrading our software from using SQL 2000 to 2008 R2. Our customers will be installing an update which uninstalls 2000 and installs 2008 R2 under the same instance. So if no instance existed, then no instance name will be set (default). However, the problem starts with the customers which have a named SQL instance. Starting in 2008 R2 (not sure of ones before), for some reason, a client connecting to the server by its instance name is unsuccessful. I'm testing from the Management Studio - if I can't connect this, then nothing can connect. I browse network servers, and find the specific server\instance in the list. But, upon trying to connect to an instance name like MyServer\INST, I get: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) I do in fact have TCP/IP and Named Pipes protocols enabled, this is the first thing I did. When I connect to the server using a comma (,) and port number like MyServer, 49195, it works just fine. So it appears that client computers are just unable to identify the instance names. This has happened on all our installations of SQL 2008 R2 and from all client computers, including Win 7, XP, Vista, Server 2008, and Server 2003. We never experienced such issues on earlier versions of SQL. The problem even persists if the firewalls and antiviruses are all disabled. Now, this is a large update which we will be distributing soon to all our customers, and we want to minimize the interaction they need with us to get this installed. We absolutely hate the idea of using a port number, because it will always be different, and we would have to modify each client to point to this server/port. Some of our customers may have hundreds of client computers. How do I make client connections to a named SQL instance work again? After all, this is the whole purpose of named instances, and if a client can't connect to this instance by its name, then what is it even named for? EDIT It was mentioned to make sure SQL Browser is running, so I checked, and it is running. The server is also able to connect to its self (locally) - just external connections are refused. UPDATE After more careful checking, I learned the firewall wasn't completely disabled when testing, and upon disabling it completely, this works. So it appears that SQL Browser is being blocked by the firewall from external clients from accessing.

  Read the article

• Is span monitoring on Cisco ASA 5520 possible?

  - by Brent

  From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

  Read the article

• Difference between sending data via UDP in Bash and with a Python script

  - by Kevin Burke

  I'm on a Centos box, trying to send a UDP packet to port 8125 on localhost. When I run this Python script: import socket sock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) sock.sendto('blah', ("127.0.0.1", 8125)) The data appears where it should on port 8125. However when I send the data like this: echo "blah" | nc -4u -w1 127.0.0.1 8125 Or like this: echo "blah" > /dev/udp/127.0.0.1/8125 The data does not appear in the backend. I know this is horribly vague but it's UDP and it's hard to determine why one packet is being sent and the other is not. Do you have any ideas about how to debug this issue further? I'm on a Centos machine.

  Read the article

• Windows XP SP3 TCP/IP No buffer space available

  - by Natalia

  I have the exactly same problem as here: Windows XP TCP/IP No buffer space available On Windows XP Pro, SP3 if one does an experiment where one tries to open TCP/IP sockets in a loop (bascially, listen port 7000, listen port 7001, etc.) After approx 649 open sockets, one will start getting errors: No buffer space available (maximum connections reached?) I've tried to edit the registry as described here http://smallvoid.com/article/winnt-tcpip-max-limit.html I set MaxUserPort = 65534 and MaxFreeTcbs = 2000, but it didn't help. What else can I do? I need 1000 server sockets. Here is the error stack: 05.04.2012 10:23:57 java.net.SocketException: No buffer space available (maximum connections reached?): listen at sun.nio.ch.ServerSocketChannelImpl.listen(Native Method) at sun.nio.ch.ServerSocketChannelImpl.bind(ServerSocketChannelImpl.java:127) at sun.nio.ch.ServerSocketAdaptor.bind(ServerSocketAdaptor.java:59) at sun.nio.ch.ServerSocketAdaptor.bind(ServerSocketAdaptor.java:52) at channelserver.NIOAppServer.initSelector(NIOAppServer.java:40) at channelserver.NIOAppServer.(NIOAppServer.java:27) at channelserver.NIOServer.main(NIOServer.java:433) at channelserver.NIOServer.main(NIOServer.java:438)

  Read the article

• CommunicationException when shutting down JBoss 4.2.2

  - by Brian

  I have deployed an application using JBoss 4.2.2 on a 64-bit RHEL5 server. Since there are other JBoss servers, I had to change some port configurations so that there would be no conflicts when starting the server. So right now I'm using ports-01 from the sample-bindings.xml file that came in the docs/examples/binding-manager/samples directory. In addition, below is a list of all the files I've edited to reflect the new ports: JBOSS_HOME/servers/default/deploy/jboss-web.deployer/server.xml: Changed Connector port - 8080 to 8180 Changed AJP 1.3 Connector port - 8009 to 8109 JBOSS_HOME/server/default/deploy/jbossws.beans/META-INF/jboss-beans.xml Changed 8080 to 8180 JBOSS_HOME/server/default/conf/jboss-service.xml: Changed 8083 to 8183 Changed 1099 to 1299 Changed 1098 to 1298 Changed 4444 to 4644 Changed 4445 to 4645 Changed 4446 to 4646 Changed 4447 to 4647 JBOSS_HOME/server/default/conf/jboss-minimal.xml: Changed 1099 to 1299 Changed 1098 to 1298 When I start the server (binding to localhost) everything is fine and I'm able to access the application. But when I try to shutdown the server I get the following error: Exception in thread "main" javax.naming.CommunicationException: Could not obtain connection to any of these urls: localhost [Root exception is javax.naming.CommunicationException : Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]]] at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1562) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:634) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:627) at javax.naming.InitialContext.lookup(InitialContext.java:392) at org.jboss.Shutdown.main(Shutdown.java:214) Caused by: javax.naming.CommunicationException: Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:274) at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1533) ... 4 more Caused by: javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:248) ... 5 more Caused by: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:525) at java.net.Socket.connect(Socket.java:475) at java.net.Socket.(Socket.java:372) at java.net.Socket.(Socket.java:273) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:84) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:77) at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:244) ... 5 more Is there any other file that I need to change the 1099 to 1299, or am I missing some other step?

  Read the article

• iptables rule to submit packets matching a specific negative rule

  - by Aditya Sehgal

  I am using netfilter_queue to pick up certain packets from the kernel and do some processing on them. To, the netfilter queue, I need all packets from a particular source except UDP packets with src port 2152 & dst port 2152. I try to add the iptable rule as iptables -A OUTPUT ! s 192.168.0.3 ! -p udp ! --sport 2905 ! --dport 2905 -j NFQUEUE --queue-num 0 iptables throw up an error of Invalid Argument. Querying dmesg, I see the following error print ip_tables: udp match: only valid for protocol 17 I have tried the following variation with the same error thrown. iptables -A OUTPUT ! s 192.168.0.3 ! -p udp --sport 2905 --dport 2905 -j NFQUEUE --queue-num 0 Can you please advise on the correct usage of the iptables command for my case.

  Read the article

• Do I make the correct difference between spwan-cgi and mod_fcgi

  - by Saif Bechan

  First of all im configuring an webserver with nginx and apache2 working together. Having only nginx is no options for me, neither is lighttdp. I am reading a tutorial 'Nginx -Apache -Proxy configuration on Centos-Plesk server' where this is exaplained in some detail. One thing i don't really understand. They are talking about installing spawn-fcgi to spawn the fastcgi process. Now if i understand this correct this program is only for nginx apache will run as normal. Apache will just run the mod_php5.c. If i want to have apache also work as fastcgi i have to confirgure that seperately, and let apache use mod_fcgi. Do I have this correct or am I talking utter nonsense. Nginx usses spawn-cgi as frontend Apache usses mod_fcgi in the back Inbetween there is a proxy that ports port 80(nginx) to port 8080(apache)

  Read the article

• How can I log all traffic with its exact length?

  - by Legate

  I want to process all packets with their size going through our gateway server (running Debian 4.0). My idea is to use tcpdump, but I have two questions. The command I'm currently thinking of is tcpdump -i iface -n -t -q. Is it guaranteed that tcpdump will process all packets? What happens if the CPU is working to full capacity? The format of the output lines is IP ddd.ddd.ddd.ddd.port > ddd.ddd.ddd.ddd.port: tcp 1260. What exactly is 1260? I have the suspicion that it is the payload in bytes of the packet, which would be exactly what I need, but I'm not sure. It might be the TCP Window Size. Or perhaps there is an even better way of doing this? I thought about a LOG rule in iptables, but tcpdump seems easier and I don't know whether iptables can log the packet lengths.

  Read the article

• PSAD Firewall/ UDP flood?

  - by Asad Moeen

  Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

  Read the article

• Connection Reset by Peer error with Apache and JBoss 7.1.1

  - by vikingz

  We are seeing errors on some of our QA testing scripts that intermittently throw Connection Reset By Peer errors. The Test scripts submit requests via F5 which forwards requests to Apache (2.2.21) with a mod_jk load_balancer with the following setting for each worker in the worker.property worker1 props worker.worker1.type=ajp13 worker.worker1.port=8109 worker.worker1.lbfactor=1 worker.worker1.host=skunkhost1.com worker.worker1.connection_pool_timeout=30 and here is what is in the JBoss domain.xml for the AJP port from JBoss 7.1.1 <unbounded-queue-thread-pool name="SKUNKY.APP.AJP"> <max-threads count="300"/> <keepalive-time time="3" unit="minutes"/> </unbounded-queue-thread-pool> Here is httpd.conf Timeout 300 KeepAlive On KeepAliveTimeout 15 MaxKeepAliveRequests 100 TraceEnable Off My question is that is it posisbe that apache times out and closes the connection while jboss is still ready and working on the request? What might be causing the Connection Reset By Peer error?what am i missing here? Any help is majorly appreciated!! Sincerely KK

  Read the article

• Tripple-Head Setup: Raedon 5770

  - by Aren B

  I currently own a Sapphire Raedon HD 5770 1GB w/ DDR5 (Link) I've got two LCDs set up in this configuration: +---------++------+ | || | | 1 || 2 | +---------++------+ Im looking into buying a new TV/Monitor, a Samsung T240HD (h**p://www.memoryexpress.com/Products/PID-MX22473(ME).aspx) and I'd like to set up a tripple monitor setup like this (new monitor being #3) +---------++------++---------+ | || || | | 3 || 2 || 1 | +---------++------++---------+ Monitor 1: DVI Monitor 2: DVI Monitor 3: HDMI PS3 - Monitor 3: HDMI2 Is this possible with my current video card? Can I plug in 2x DVI + 1x HDMI and get a third display? Or am I going to have to buy a slew of Display Port Adapters? I know older video cards you could only have 2 active displays, but I heard that barrier was defeated with the Display-Port series video cards.

  Read the article

• What is the "right" way to host CUPS behind Apache 2

  - by Greymeister

  I have tried some combinations of ProxyPass, ProxyPassReverse and ProxyHTMLURLMap but I'm still not having much luck. I just would like to be able to hit the printers in CUPS by going to www.printerhost.com/printers/printername rather than having to add a port 631 or have CUPS listen on port 80. As requested, here is the configuration file: LoadModule proxy_html_module modules/mod_proxy_html.so LoadModule xml2enc_module modules/mod_xml2enc.so NameVirtualHost *:80 <VirtualHost *:80> ServerName blah.yours.com JkMount /* balancer JkMount /jkmanager jk-status JkUnMount /cups* balancer ProxyRequests Off ProxyPass /cups/ http://localhost:631/ ProxyHTMLURLMap http://localhost:631 /cups <Location /cups/> ProxyPassReverse / ProxyHTMLEnable On ProxyHTMLURLMap / /cups/ </Location> </VirtualHost>

  Read the article

• Google SMTP settings not sending email

  - by Baboon

  I am having a hard time making the email sending in GitLab to work (changing email in profile settings). My server has exim4, I can tell its working because if I do simple mail() in PHP, it thus sends the email to the recipient. Now, in GitLab seems that it wasn't. So I modified productions.rb to have SMTP settings, and use Google SMTP: config.action_mailer.delivery_method = :smtp config.action_mailer.smtp_settings = { address: "smtp.gmail.com", port: 465, user_name: "[email protected]", password: "hashpassword", domain: "gmail.com", authentication: :plain, enable_starttls_auto: true } I even tried changing the port to 587 and 467 but still it doesn't work. Why is that? Can you please lead me to where I am missing?

  Read the article

• Http to https behavior for visits from Internet Explorer client

  - by Emile

  My website has an SSL cert (example url: https://subdomain.example.com). Under Apache it's set up for both port 80 and port 443. So under the following configuration, anyone who goes to http://subdomain.example.com is sent to https://subdomain.example.com . But for visits from Internet Explorer, the redirect doesn't happen. Instead, http visits get a "Internet Explorer cannot display the web page." with a list of client-side solutions to try. Any ideas on how to fix the config so IE visits have the same behavior as the other browsers (that is, send http to https automatically)? NameVirtualHost *:443 <VirtualHost *:80> DocumentRoot /var/www/somewebroot ServerName subdomain.example.com </VirtualHost> <VirtualHost *:443> DocumentRoot /var/www/somewebroot ServerName subdomain.example.com # SSL CERTS HERE </VirtualHost> *Tested IE8, IE9 beta

  Read the article

• Powershell: Cannot connect via SSL

  - by JSWork

  Am following "secrets to powershell remoting" to setup an SLL account and seem to be missing a step. I ran Winrm create winrm/config/Listener?Address=*+Transport=HTTPS @{Hostname="redacted";CertificateThumbprint="redacted"} and got PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1184937132 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1184937132 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 5985 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1187163138 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1187163138 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 80 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_220862350 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_220862350 Name Value Type ---- ----- ---- Address * System.String Transport HTTPS System.String Port 5986 System.String Hostname redacted System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint redacted System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String Trouble is when i do this PS C:\Users\redacted> enter-pssession -Computername redacted -Credential redacted\redacted -UseSSL I get this Enter-PSSession : Connecting to remote server failed with the following error message : The client cannot connect to th e destination specified in the request. Verify that the service on the destination is running and is accepting requests . Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or Win RM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". For more information, see the about_Remote_Troubleshooting Help topic. At line:1 char:16 + enter-pssession <<<< -Computername redacted -Credential redacted\redacted -UseSSL + CategoryInfo : InvalidArgument: (redacted:String) [Enter-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CreateRemoteRunspaceFailed This happens even when the firewall is off completely and when the machine tires to connect to itself locally. On top of that, despite the listners eing lsited on wsman, when I run PS WSMan:\localhost&gt; Get-PSSessionConfiguration I get Name PSVersion StartupScript Permission ---- --------- ------------- ---------- Microsoft.PowerShell 2.0 PS WSMan:\localhost&gt; Any ideas what I'm missing/doing wrong? edit: Windows 2003. Powershell v2.0

  Read the article

• Why do I have to manually 'Restart Management Network' on vSphere 5 host after reboot to get networking available?

  - by growse

  I've got a couple of vSphere 5.0 hosts in a small lab environment here and I've noticed a strange behaviour. When on of the hosts gets rebooted, it is unresponsive to the network until I log into the ESX console, Press F2 to customize and select Restart management network. Once this is done, the networking works perfectly as expected. Each host has two NICs which are trunked together using Etherchannel to a Cisco 3750. The link is also a .1q VLAN trunk and the management network is configured on VLAN121 with the VM traffic configured on VLAN118. Why would the host be completely dead to the world until I physically kick it? Edit Sample switch config for trunk: interface Port-channel2 description Blade 1 EtherChannel Trunk switchport trunk encapsulation dot1q switchport mode trunk end ! ! interface GigabitEthernet4/0/1 description Bladecenter1 CPM 1A switchport trunk encapsulation dot1q switchport mode trunk speed 1000 duplex full channel-group 2 mode on end Vswitch teaming settings: Management port group settings:

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >