Search Results

Search found 9273 results on 371 pages for 'boot repair'.

Page 158/371 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

  • Out Of disk, but still boots

    - by LinuxPCplus
    I have a HP Compaq nx6310 notebook wth 4gb memory & a new 250gb hdd. After installing Ubuntu 12.04, i got an "out of disk" error & was unable to boot. I rebooted in live, instaled & ran Boot Repair then rebooted. Grub menu loaded fine, followed by "out of disk.....press any key to continue". I pressed a key & Ubuntu booted, a bit slow but still booted. So here are my questions: 1- Since Ubuntu DOES boot, should I just leave it alone? 2- If I need to fix this, HOW do I do it? 3- What causes this error? $wolf@lpc-1:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 230G 9.1G 209G 5% / udev 1.6G 12K 1.6G 1% /dev tmpfs 655M 868K 654M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.6G 260K 1.6G 1% /run/shm wolf@lpc-1:~$

    Read the article

  • Screen Corruption in half the screen only

    - by Guy DAmico
    About 50% of the my NATTY desktop screen is corrupted. Once that happens I can re-boot as many times as I want but the problem continues. If I logout and then into WINDOWS for a day I may be successful and boot UBUNTU with a good screen. The desktop is formatted correctly, there's no pixelation, rather there is a fine grained white crosshatch pattern covering the entire screen. If I open any application the screen corruption worsens eventually to the point I can no longer make out anything. I ran ram memory test w/o any errors. I have no display issues when running WINDOWS 7. Any ideas. My computer is a Dual Boot stock DELL 5150 w/3gig of ram an on board video.

    Read the article

  • No root file system - Alternate CD + LVM

    - by Carlos
    I am trying to install 11.10 as dual boot with Windows 7. I have all partitioned well as you can see here: http://www.flickr.com/photos/42897978@N00/7111180385/ I burned the Alternate CD ISO to a CD. Boot from it and followed instructions to Partitioning. There, I configured the LVM partitions as follows: Volume Group ubuntu-vg - Uses Physical Volume /dev/sda7 380GB - Provides Logical Volume home-lv 60GB - Provides Logical Volume root-lv 60GB - Provides Logical Volume swap-lv 6GB That is all I want (note that my /boot is outside of LVM) Then when I say that all is Ok and to write it to disk and continue with the installation, I get the following error. !! Partition Disks No root file system No root file system is defined Please correct this from the partitioning menu. What should I fix and how? I tried issuing the "Revert changes to partitions", but nothing happens. It seems that the LVM configuration has already been written to the CD. HELP!!

    Read the article

  • Script at Startup

    - by OttoRobba
    I'm using 10.10 and I need to run a script in order to get a windows-like international keyboard layout - basically, it changes how dead keys work. (Original script from this page http://t.tam.atbh.us/en/win-us-intl-4-linux/ ) Since I can't seem to manage to get it going from boot, I have to run a custom script to launch any application. The script: export GTK_IM_MODULE=xim setxkbmap us intl xmodmap -e 'keycode 48 = dead_acute dead_diaeresis dead_acute dead_diaeresis acute diaeresis' application_name So if I put abiword in the application_name, it runs abiword respecting the keyboard script. Ideally, the original script would start at boot and then any applications I use would function with it - just like what happens if I run it first in Terminal (without the app_name line) and then run apps from it. I tried to make the script run from boot by adding it to /etc/rc.local but to no avail. Tried to add it to init.d but that also didn't work. If anyone can help, I'd be most grateful.

    Read the article

  • Loads wrong resolution when installing

    - by Kevin DB
    I'm trying to install Ubuntu 11.04 from a USB. My computer does load the USB file and I get some sort of BIOS-like screen where I can choose between 'Install from USB' and 'Boot-up from USB'. When I entered the corresponding number my screen resolution is totally messed up. I see that Ubuntu is starting up when I used Boot from USB, but the screen looks the same as you'd have a too high screen resolution. Same story with Install from USB. I can see the screens loading and the menu's and stuff, but not clearly because it load in a too high screen resolution. I'm trying to dual-boot is with Windows XP and max. screen resolution is 800x600.

    Read the article

  • Installation of 11.10 on new drive (no OS)

    - by Jeffrey Vincent
    I have a Dell Dimension 600 XPS Phoenix BIOS version A03, the original HD crashed and burned. Dell didn't send OS disks (was on the original drive and no back up disks), so I am trying to install Ubuntu 11.10 on the new drive. The new drive is a Western Digital 1TB. I formatted the new drive by putting it in an enclosure and formatting it with Windows 7 on my HP system. When I put the cd in the cdrom it boots to the cd with the Advanced user screen (won't boot into the usually Windows GUI). When I try to install (or run from live Cd) I get the same error message. Same with trying the various boot options. The message is: VFS: cannot open root device "(NULL)" or unknown-block(8,1) Please append a correct "root=" boot option: Here are the available partitions: Kernal Panic- not syncing: VFS: Unable to mount rootfs on unknown-block(8,1) and then it lists Trace messages then freezing. Any help or suggestions are appreciated in advance.

    Read the article

  • My Oracle Support E-Business CRM Communities = Answer Hubs

    - by Oracle_EBS
    Want a quick answer to your EBS CRM problem?  Try our My Oracle Support E-Business CRM Communities.  Another avenue to get timely and accurate support and solutions from Oracle Support experts, industry peers and it's searchable to learn from others experiencing the same issues.  Give them a try! Oracle Complex Maintenance, Repair and Overhaul Community Oracle Contracts Community Oracle Depot Repair Oracle Install Base Community Oracle Lease & Finance Community Oracle Mobile Field Service Community Oracle Quoting Oracle Sales and Marketing Oracle Sales Compensation Oracle Service Community Oracle Telesales Oracle Trade Management

    Read the article

  • Problems after installing Ubuntu 11.10

    - by Andrew Orr
    I'm having trouble with Ubuntu 11.10. It has to do with nomodeset. After I boot into Ubuntu, it goes to a purple screen for about 10 seconds and then goes blank. After that nothing happens. I've read other people's questions about this and I know it has to do with enabling nomodeset. This worked for me when I was using the LiveCD mode, but now Ubuntu is permanently installed as a dual-boot system. Going into recovery mode doesn't work, pressing "e" in the boot loader and writing nomodeset after quiet splash doesn't work either. Holding shift any time it's booting doesn't work. I don't know what to do anymore. I have an HP Pavilion dv6 laptop with an AMD A6-3400M CPU, and my GPU is an AMD Radeon HD 6520G. I've never worked with Linux before so taking me through this step-by-step would be great. Thanks!

    Read the article

  • Problem with lucid install from ISO.

    - by joon
    Hi, I am trying to install Lucid from an iso (bios doesnt let me boot from USB and dvd drive is busted). I followed the instructions on the bottom of this page: ´The CD image approach´ https://help.ubuntu.com/community/Installation/FromWindows The ubuntu ALTERNATE iso is in my c: root dir. I even tried a fix that used to work in older versions (found on a forum) but that did nothing. What happens: - boot until the boot.ini menu - select install ubuntu - select install ubuntu again, I´m assuming this is grub - do some country settings,.. - harddrive is scanned for ISO image - not found, not even with thorough search...

    Read the article

  • Restoring windows path on Windows 7

    - by Renso
    Issue:You changed the windows path and made a mistake and now want to reset it.Solution:In short, you can't. If you restore to the system default, you will loose any paths that were appended when you or the manufacturer installed software and drivers. Each time you install some sort of software or driver, MS Office, Turbotax, etc., it creates/appends to the path so that it points to it's start-up program.Too late now, but you should create a restore point BEFORE you touch the windows path if you are not sure what you are doing:http://www.sevenforums.com/tutorials/700-system-restore.html http://www.sevenforums.com/tutorials/2083-system-repair-disc-create.html At a minimum you need the following:%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\AT worst you can reset it to the above, and go through each application as you use them and run into problems to fix the path. The REPAIR option when you select to change/uninstall a program can help with that.

    Read the article

  • Kernel Panic Fatal Machine Check

    - by 0x4a6f4672
    I have got a new Samsung Series 7 laptop with dual boot setup for Windows 8 and Ubuntu 12.10. The Ubuntu installation was quite a hassle, but with the help of Boot Repair finally it seemed to work. Or so I thought. Windows 8 starts fine, but if I want to start Ubuntu regularly the following error occurs, quite similar to this one [Hardware Error] CPU 1: Machine Check Exception: 5 Bank 6 [Hardware Error] RIP !inexact! 33 <00007fab2074598a> [Hardware Error] TSC 95b623464c ADDR fe400 MISC 3880000086 .. [similar messages for CPU 2,3 and 0] .. [Hardware Error] Machine Check: Processor context corrupt Kernel panic - not syncing: Fatal Machine Check Rebooting in 30 seconds Kernel panic does not sound good. Then it starts to reboot, and the second boot trial often works. Is it a Kernel or driver problem? The laptop has an Intel Core i7 processor. I already deactivated Hyperthreading in the BIOS, but it does not seem to help :-(

    Read the article

  • can't install software--can I fix missing dpkg?

    - by user125272
    New software can't be installed, because there is a problem with the software currently installed. Do you want to repair now? hit Repair Package operation failed The installation or removal of a software package failed. Details => installArchives()failed:Could not exec dpkg! Error in function (synaptic:12725): GLib-CRITICAL **: g_child_watch_add_full: assertion 'pid > 0' failed Could not exec dpkg! E: Sub-process /usr/bin/dpkg returned an error code (100) A package failed to install. Trying to recover: sh: 1: dpkg: not found

    Read the article

  • How can I run Ubuntu if it's not on my main drive?

    - by Stephen
    I have a 120GB SSD and a 750GB HDD in my computer. My SSD has Windows 7 installed and my HDD has Windows 8 installed. When I boot my computer normally, I boot it to my SSD. I went through the installation process, putting Ubuntu on a separate partition on my HDD. When I restarted my computer, it didn't give me an option to boot to Ubuntu. If it helps, I believe I used ext4 and only set it to '/'. If I want to make Ubuntu bootable from my computer, how would I go about doing that?

    Read the article

  • Problem with Ubuntu and UEFI (Problem with any linux OS)

    - by K.T.Sumant
    I have purchased a new Sony Vaio laptop and it is said that the Windows in the recent laptops is installed in the UEFI mode. But all the Linux OS are installed in default in Legacy mode. When I reboot my laptop, Ubuntu is not being detected on boot. Only Windows is detected. To access Ubuntu, whenever I boot the system, I need to: (1) enter the boot menu, (2) change the mode to legacy, and (3) type a bit of scary commands in grub then Ubuntu successfully opens. This is a bit of problem for me. So I wanted to know the solution for this problem. So please kindly look over my problem as soon as possible.

    Read the article

  • How can i modify my Grub 1.99 configurations to install a new kernel?

    - by abhi
    I have configured kernel 3.2.x and made some changes in the kernel. I have compiled it and have the compiled image of the kernel with me. The problem i am facing is as in how to modify the boot loader Grub 1.99 in my case, so that i can boot through the new kernel i have compiled. I looked on net for any tutorials but all of them talked about older versions of Grub ? Can someone please give some info or point me towards some resource ? Currently i have compiled my new custom kernel image and have copied it to /boot.

    Read the article

  • Why does update-grub not find ubuntu 11.10?

    - by Klaynos
    I've recently installed ubuntu onto my laptop. With the intention of dual booting with windows 7. On installation Grub wasn't loading, the computer continued to boot straight into windows. I loaded a live cd, mounted the installed ubuntu partion (sda6) as /mnt/ and windows boot partition as /mnt/boot Following the second option here: http://ubuntuguide.net/how-to-restore-grub-2-after-reinstalling-windows-xpvistawin7 Through its entirety, so creating a new grub.cfg file. chroot /mnt update-grub Did not find ubuntu, just windows 7 and the windows recovery partition. Thinking this might be a weird quirk that as I was in ubuntu (all be it a live cd) it might not list ubuntu I restarted. Grub loaded but ubuntu was nowhere to be seen. How can I add ubuntu with Grub2? I could have fixed this myself in old grub but I'm pretty much in the dark here. Thanks

    Read the article

  • Does the Ubuntu mini.iso work with EFI?

    - by jean388
    I have to install Ubuntu 11.10 from the AMD64 mini.iso on a system with UEFI BIOS motherboard. I have configured a virtual machine in VirtualBox for making a test install before I setup the real system. In VirtualBox I have enabled EFI. When the virtual machine is powered on and boot mini.iso the Grub commandline is shown. If I try to boot the normal Ubuntu CD it works fine and I get the normal boot options "Install Ubuntu" etc. Does Ubuntu mini.iso not work with EFI?

    Read the article

  • mail server crash

    - by waxx
    i have a mail server running ubuntu 12.04. my server has a main 200gb hdd as the /, and other scsi hdd. as far as i recall, i used the 5 scsi harddrives for different mount points.. 1 hard drive is /swap, 1 hard drive is /usr ...the other is /boot, i cant recall the other 2.. just yesterday, my /usr drive died... and it wont let me boot into the server.. ive tried to skip mounting the /usr with the S option when i go to recovery drive, but the server still wont boot up. i need help badly because the server needs to be up and running ASAP. thank you for all the help.

    Read the article

  • bootloader install failed

    - by user211860
    I have lenovo u510 with windows 8. This ultrabook has 24GB SSD and I tried to install Ubuntu 12.04.3 in it. I changed bios from UEFI to legacy and I used a LiveDVD. I created a 17GB partition when I was in windows from this SSD and I tried both manualy or with the "install alongside" but was allways without success because bootloader install failed and was unable to install GRUB. I tried also to use the "recommended repair" from Boot-Repair but it says that my laptop can only with UEFI boot. I changed it but the same thing happens my laptop boot in windows 8.

    Read the article

  • A real noob question

    - by Jaymz
    I have a Hp mini netbook that has been wiped clean, there is nothing other than the bios on it, it has no DVD and I don't have an external DVD. I can change the boot order to boot from a usb device. I have downloaded ubuntu-12.04.1-desktop-i386 I have one of these http://www.kikatek.com/P100600/34609-IOMEGA-250gb-Select-Portable-HDD-2-5-USB?source=froogle currently formatted to NTFS but I can format to exFAT I have tried Linuxlive USB creator, all that managed to do was dual boot the desktop pc that I'm working off, and when booting on the wiped clean netbook, just left me with a black screen with a blinking cursor I have also tried Unetbootin, this managed to change my 'My Computer' icon to Install Ubuntu (C:) and now again, my desktop pc dual boots with the Wubi software, the Unetbootin, wouldn't let me select my external drive to write to Please I'm a complete idiot, i need a super idiots guide to doing this Regards Jaymz

    Read the article

  • How to add a command permanently to grub2

    - by tomodachi
    I have a fairly special setup, using Linux on a MacBook Laptop. to switch off my secondary graphics card in it I'm required to add these lines to my grub outb 0x728 1 outb 0x710 2 outb 0x740 2 outb 0x750 0 I do this by pressing 'e' for my selected grub menu option and adding the lines one by one . then finally booting . But as we know it's not permanent. I cant really figure out where i need to add it for grub to always append it to my Linux boot options. It's doesn't seem to belong in /etc/default/grub since here i can add stuff to the kernel boot line Honestly i'm afraid to fiddle to much with grub on my computer since getting it to triple boot Linux/Mac/Windows was a very delicate and timely matter. Does anyone have any idea of where to add it?

    Read the article

  • Ubuntu 12.04 very slow on samsung netbook

    - by vallllll
    I have a samsung netbook n150 1Gb Ram (Intel graphic card), 1,66GHz Intel Atom processor. It was working great with the ubuntu 10.04 netbook edition, really fast boot very eficient but I have updated to 12.04 (the netbook edition doesn't exist anymore) and now the system is so slow: slow boot, sometimes it doesn't even boot properly, strange screen light on and off behaviour, when you click on an icon takes for ever to open the app even the terminal it takes like more than 10s! It seems that this new distro was made for a far more powerful systems than this netbook. I am considering to revert back to 10.04 or choose another linux distro but is there anythhing i can do to fix these problems? Any body else had similar problems. Thanks in advance

    Read the article

  • Why does installing Grub2 give an "ISO9660: filesystem destruction..." warning?

    - by Ettore
    I have installed Ubuntu 12.04 on my computer, but at the end of the installation it gave me an error and it didn't install grub2. Now I'm trying to install it using the live cd: This is my sudo fdisk -l: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x6af447e6 Device Boot Start End Blocks Id System /dev/sda1 * 2048 781459455 390728704 7 HPFS/NTFS/exFAT /dev/sda2 781459456 789272575 3906560 82 Linux swap / Solaris /dev/sda3 789272576 976773119 93750272 83 Linux After mounting and chroot the linux partiton, I give grub-install /dev/sda command, and I get: /usr/sbin/grub-setup: error: hd0 appears to contain a iso9660 filesystem which isn't known to reserve space for DOS-style boot. Installing GRUB there could result in FILESYSTEM DESTRUCTION if valuable data is overwritten by grub-setup (--skip-fs-probe disables this check, use at your own risk). (same error even with grub-install --recheck /dev/sda) What can I do? I also tried boot-repair, but I get this error: http://paste.ubuntu.com/1069353/

    Read the article

  • it started with a broken package

    - by Inteloidl.com
    all started when i tried to updated to the latest lts, but the problen is that the update interumpted and some broken packages apeared, i used synaptics to repair, but it wont repair, iv tried some console from some forum topic ... and in the end when i try to open synaptic or update managre this is what apears any ideas : E: Dynamic MMap ran out of room. Please increase the size of APT::Cache-Limit. Current value: 25165824. (man 5 apt.conf) E: Error occurred while processing mantis (NewVersion1) E: Problem with MergeList /var/lib/apt/lists/c.archive.ubuntu.com_ubuntu_dists_lucid_universe_binary-i386_Packages E: The package lists or status file could not be parsed or opened. E: _cache-open() failed, please report. W: Unable to munmap

    Read the article

  • Can I set Ubuntu 12.10 to automatically reboot to Windows once only?

    - by Bill Tetzeli
    Is there some way when I'm in Ubuntu 12.10 that I can set it to reboot automatically to Windows just once, so that when I'm in Windows I can reboot and it will automatically boot back into Ubuntu? I need this because often when I travel I access my home computer for email and other personal info that I don't want to travel with or leave to the tender mercies of the "cloud". On rare occasions, I need to temporarily boot into Windows 7 to do something Windows-specific, but then I want to be able to boot back into Ubuntu because that's where most of my computing takes place. Any ideas? Thanks in advance! Bill

    Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >