Search Results

Search found 18580 results on 744 pages for 'wireless connection'.

Page 158/744 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• Can D-Link DIR-600 work in client mode?

  - by Ivan Petrushev

  Using default firmware I can't find anywhere option of changing mode to something other than access point. Can DIR-600 work in client mode with default or some other firmware? Are other modes available?

  Read the article

• Load-balance with LAN and Wi-Fi

  - by Synox

  I have a Mac, which runs Mac OS X 10.6 or Ubuntu 9.10 or Windows XP (Multiboot). Solution can be for any of the systems, whatever works better. I have two ISPs, one can be accessed via Wi-Fi, one can be accessed via LAN. In Mac OS X I can define the priority, which network to choose first. But what I wish to do is to load-balance with both networks. I don't want to buy extra hardware. I have some unused Wi-Fi routers if this would help. Compiling and configuring programms in Linux is no problem for me.

  Read the article

• Laptop kicks other users off the wifi when it connects, then gets disconnected itself

  - by Devon

  I've got an Acer Aspire One running Linux. When I connect to my building's wifi, everything seems fine for a short period of time (I can google a few things or start downloading an Apt package), but then other devices on the network lose their IP addresses. Shortly after that, my computer also gets disconected. My computer is set to use DHCP. What causes this, and do you know how it could be fixed? Am I causing a broadcast storm?

  Read the article

• USB-to-Parallel adapter rated as USB 1.1 - will its driver lower speed of USB 2.0 bus?

  - by cumminjm

  I need to connect a printer with a parallel port to a computer with only a USB 2.0 bus. I'd like to do so without lowering the USB 2.0 bus speed to USB 1.1. All the USB-to-Parallel adapter cable found so far seem to be rated as USB 1.1 and they come with a CD which presumably contains a necessary driver. I haven't purchased one and tested it out yet, but if so, would the cable's driver lower speed of USB 2.0 bus?

  Read the article

• Can't access certain specific IP/domain on Windows 7

  - by jfrobishow

  Been banging my head on the wall for some time now. I have a fresh install of Windows 7 - Ultimate ~x86. Some IPs can't resolve properly, it doesn't matter if I try using Firefox, Chrome or IE I end up with a domain not found (server not found, etc.) I am behind a router, all the other computers aren't affected only this Win 7 machine. It's only certain sites. e.g. xkcd.com, facebook's cdn, google group. Things I have tried: flushdns ipconfig renew Disable IP v6 on the NIC Double checked that the computer was in the right timezone @ the right time. Reinstall the NIC driver. Again 90% of the sites will work but not the major one :P help!!!

  Read the article

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

• Pushing WiFi configuration through Active Directory

  - by Hank Gettinger

  I'm trying to push wifi settings to client computers through Active Directory, something that will add a defaul SSID to connect to and a WPA password. The only thing I've heard of is a script by Aruba labs called wificfg_xp.exe on a couple of forums (Here and here), but the link to the download page is always broken. Does any one know of an alternative way to download this file, or another way to push these settings with AD?

  Read the article

• 4 - 7 second delay accessing Mysql across the network

  - by Kristiaan

  Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

  Read the article

• Setting up VM server access via host MacBook Pro's WiFi hotspot

  - by user7609

  I have a virtual machine (VM) hosted on a MacBook Pro (MBP). There is a server installed on the VM. I'm trying to make this server accessible via MBP's WiFi hotspot so I can see it from my iPhone when connected to the hotspot. The VM is Parallels (latest version) and its OS is Win7 and the MBP is 2013 with Mavericks. With default settings and no hotspot enabled I can access the VM's server from the host OSX. The network setting on the VM is "Shared" and it's IP is 10.211.x.x. When I join the hotspot from another laptop the other laptop gets an IP 169.254.x.x and it can't ping 10.211.x.x or access the server on that VM Is there a combination of settings on the VM and MBP's hotspot such that I can access the VM server from a client on the MPB's hotspot?

  Read the article

• How to take advantage of two Internet connections (WiFi / Wired) ?

  - by Madhur Ahuja

  I have two separate internet connections, one through WiFi and other Wired. However, generally I have observed that Windows try to use only one ( mostly faster one/ Or Wired by preference - I am not sure). Is there a way I can take advantage of having both ? For example I can have my web browser use the wired one and my torrent software use the Wifi One. PS: This question may be regarded as duplicate but reason I am posting it again is I have not found any concrete answer for it. Two internet Connections, one LAN - how to share?

  Read the article

• Add 802.11n to existing 802.11g environment

  - by Andrew Robinson

  I have a small home network that is currently running 802.11g. Two computers that are capable of 802.11n and two devices (a BlackBerry and a Skype phone) that are limited to 802.11g. I have a few neighbors running 802.11g but their signals are very weak. How big an impact will the two G devices have on N speeds? Will they pull the whole network back down to G? These two devices are hardly ever used where as the other N devices are heavily used. If I add an N router to the network (instead of replacing the G) and set my existing G router to use channel 1 with 20MHz bandwidth and then set the N router to use 6 & 11 for 40MHz will I eliminate the overlap and allow for full speed on both networks?

  Read the article

• How to use ipw3945 on Ubuntu 9.04

  - by Aaron

  Note: uname -a 2.6.28-16-generic cat /etc/issue Ubuntu 9.04 \n \l I have disabled iwl3945: cat /etc/modprobe.d/blacklist.conf | tail -3 blacklist iwl3945 blacklist mac8021 Question: How can I use iwp3945 instead?

  Read the article

• OpenWrt Backfire 10.03 Frequently Becoming Unresponsive (Bridged Client)

  - by Christopher Parker

  I have a Linksys WRT54G version 2 that I've flashed with OpenWrt Backfire 10.03. It's acting as a bridged client using the wl.o driver to give me network access in my home office, which is in a far corner of my house in a position that would make it exceedingly difficult to fish network cabling in through the walls. I have three network-ready devices attached to the device that don't currently support WiFi, including a networked printer. Ever since I migrated from WhiteRussian, which was also set up as a bridged client, to Backfire, the device has been becoming unresponsive, as though the OS itself has crashed or frozen. The WLAN light becomes completely solid and the LAN lights stay mostly solid, blipping off and then back on again maybe once a second or so. They all blink more or less in unison. Is there some way I can diagnose why this is happening so I can fix it? Right now, the only way to fix it is to unplug the device and plug it back in.

  Read the article

• How to connect SharePoint Online with Dynamics CRM Online using BDC?

  - by ripperus

  I try to connect SharePoint Online with Dynamics CRM Online using BDC. But without any results. I'll try to using Account's from CRM in SharePoint Online like a list. I mean - when I have 100 account's (customers) in CRM I want to export this account's to SharePoint Online like a list. And when I will bed edited account in CRM the elements in the list will be update (and when I edited element on SharePoint list it will update in CRM). Is there any possibility to connect in this way? If if what I should use - SharePoint Designer 2010, Visual Studio or do this on web interface?

  Read the article

• For IIS 7, do you know where to configure number of connections from application pool?

  - by Pra Che

  how do I configure connections in IIS7

  Read the article

• Access Methods to a computer Using MAC Address

  - by Dimal Chandrasiri

  I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

  Read the article

• PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

  - by lcbrevard

  When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

  Read the article

• connect to paltalk server using a proxy

  - by user40026

  Hi I want to use paltalk, which is a kind of chat software, but the ports that this applications uses are closed in my country. What I need to do is to use a proxy server. Unfortunately the software itself does not provide a proxy setting. I though it would be possible to run paltalk on an O.S. installed on a virtual machine (say virtualbox) and configure the network setting of virtual machine to direct all its traffic through a proxy on host Operating system, but I could not find a way to do so neither. can anyone please help me?

  Read the article

• Connect android to linux laptop

  - by Claudio Ferraro

  I've a laptop with linux and wanna to connect an android device to the linux machine. On linux i have an mpd server installed. wanna to be able to connect from an android mpd client to the server which resides on the laptop. I tryed to create an Ad-hoc Wifi network on linux but the Android cannot find the Wifi network..How can I proceed..Should I buy a wifi access point or something like that ? I've a wifi router , it could help me somehow ?

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• Best way to connect a desktop computer to a 3g network

  - by dbyrne

  A friend of mine is moving to a building with no Internet connectivity. Ethernet and wifi are out of the question. What is the best way for him to get his desktop connected? The most obvious solution is for him to get an unlimited 3G data plan. What is the best way for him to set this up? I am assuming he should get something like Verizon's MiFi 3G access point, but does this have an ethernet jack?

  Read the article

• wifi routers and concurrent devices

  - by Joelio

  We have a Linksys WRT54G WiFi router in our office which was working great when we had 5-6 folks. Now on peak days we have 10-15 people, each with a computer, smartphone, etc, and an ooma VOIP device. On average 1-2 times a day I need to go hard reboot the router, and sometimes the border router (Cox-supplied device). I assume this is just because the router cant handle this many concurrent users. So my question is can these consumer routers handle this kind of load? If not, would adding more devices solve the problem, and how close proximity can I put 2 routers without having interference problems (our office area is not that big physically)?

  Read the article

• Can't connect to YouTube from specific network

  - by Tyilo

  Using my current network, I am unable to connect to http://www.youtube.com/. It doesn't matter what browser I use or if I use a cli-command (wget, curl). Error in Google Chrome: Oops! Google Chrome could not connect to www.youtube.com Error using curl: curl: (7) couldn't connect to host If I use nslookup to get the IP-address of YouTube, I get 173.194.32.32. If I go to http://173.194.32.32/ in my browser it can connect, but as Google is probably checking the Host HTTP-header, it shows Google's frontpage instead. There is no blocked websites on the router and other devices on the network seems to work. My computer only has this problem on this specific network. I am using Mac OS X 10.8.2 on a MacBook (mid 2009).

  Read the article

• How to take advantage of two Internet connections (WiFi / Wired)?

  - by Madhur Ahuja

  I have two separate internet connections, one through WiFi and other Wired. However, generally I have observed that Windows try to use only one ( mostly faster one/ Or Wired by preference - I am not sure). Is there a way I can take advantage of having both ? For example I can have my web browser use the wired one and my torrent software use the Wifi One. PS: This question may be regarded as duplicate but reason I am posting it again is I have not found any concrete answer for it. Two internet Connections, one LAN - how to share?

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >