Search Results

Search found 5853 results on 235 pages for 'vivian short'.

Page 159/235 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• Very different results from df after a few seconds

  - by tatus2

  When the backup moves the files from one server to the other the results from df change every few seconds in an impossible manner. The source host is running rsync. On the destination host I'm running the following command every few seconds: echo `date` `df|grep md0` Results are below: Sat Jun 29 23:57:12 CEST 2013 /dev/md0 4326425568 579316100 3527339636 15% /MD0 Sat Jun 29 23:57:14 CEST 2013 /dev/md0 4326425568 852513700 3254142036 21% /MD0 Sat Jun 29 23:57:15 CEST 2013 /dev/md0 4326425568 969970340 3136685396 24% /MD0 Sat Jun 29 23:57:17 CEST 2013 /dev/md0 4326425568 1255222180 2851433556 31% /MD0 Sat Jun 29 23:57:20 CEST 2013 /dev/md0 4326425568 1276006720 2830649016 32% /MD0 Sat Jun 29 23:57:24 CEST 2013 /dev/md0 4326425568 1355440016 2751215720 34% /MD0 Sat Jun 29 23:57:26 CEST 2013 /dev/md0 4326425568 1425090960 2681564776 35% /MD0 Sat Jun 29 23:57:27 CEST 2013 /dev/md0 4326425568 1474601872 2632053864 36% /MD0 Sat Jun 29 23:57:28 CEST 2013 /dev/md0 4326425568 1493627384 2613028352 37% /MD0 Sat Jun 29 23:57:32 CEST 2013 /dev/md0 4326425568 615934400 3490721336 15% /MD0 Sat Jun 29 23:57:33 CEST 2013 /dev/md0 4326425568 636071360 3470584376 16% /MD0 As you can see I start from USE of 15% and after 15 seconds I'm at 37% (I don't need to mention that the backup can not copy this huge amount of data in such a short time). After ~20 seconds the cycle closes. I'm again roughly at the same usage as earlier. The value is reasonable, ca. 35 Mb were copied. Can somebody explain to me what is going on? Does df only make an estimation of usage instead of used value?

  Read the article

• Looking for comprehensive computer monitoring software

  - by cornjuliox

  Summer in this country is insanely hot. So hot in fact, that I think we just lost a machine due to overheating (last recorded CPU/GPU temp was close to 100 C, now it wont start and lets out a long series of short beeps on power up), but that's not my concern here. Since heat is such a problem for me, I use several different pieces of software to monitor temperatures in my machine. I use MSI Afterburner to monitor GPU temp, control GPU fan speed and for some light overclocking, and then I use Speccy and SpeedFan to monitor the rest of the system, CPU temp and everything. The setup works fine for now, but I want to consolidate all this into one program so I'm not juggling several windows at once. Is there any program out there that will let me monitor the following from a single window: CPU Temp and Fan Speed CPU clock GPU Temp and Fan Speed GPU clock, both core and memory Additionally, mobo temp (Speccy lists both CPU and Motherboard temp, I assume that the latter is referring to North and Southbridge temperatures. I'm also looking for the ability to chart these data points on a graph over time, basically to see just how high the temperatures spike under load and for general analysis. It'd be nice if it could handle overclocking of both CPU and GPU in real time too. Any suggestions? Edit: I forgot to mention that I'm on Windows 7, 64-bit

  Read the article

• Administrator view all mapped drives

  - by kskid19

  In my understanding of security, an administrator should be able to view all connections to and from a computer - just as they can view all processes/owner, network connections/owning process. However, Windows 8 seems to have disabled this. As administrator running an elevated in Win Vista+ when you run net use you get back all drives mapped, listed as unavailable. In Windows 8, the same command run from an elevated prompt returns "There are no entries in the list". The behavior is identical for powershell Get-WmiObject Win32_LogonSessionMappedDisk. A workaround for persistent mappings is to run Get-ChildItem Registry::HKU*\Network*. This does not include temporary mappings (in my particular example it was created through explorer on an administrator account and I did not select "Reconnect at sign-in") Is there a direct/simple way for Administrator to view connections of any user (short of a script that runs under each user context)? I have read Some Programs Cannot Access Network Locations When UAC Is Enabled but I do not think it particularly applies. ServerFault has an answer, but it still does not address non-persistent drives How can I tell what network drives users have mapped?

  Read the article

• Administrator view ALL mapped drives

  - by kskid19

  In my understanding of security, an administrator should be able to view all connections to and from a computer - just as they can view all processes/owner, network connections/owning process. However, Windows 8 seems to have disabled this. As administrator running an elevated in Win Vista+ when you run net use you get back all drives mapped, listed as unavailable. In Windows 8, the same command run from an elevated prompt returns "There are no entries in the list". The behavior is identical for powershell Get-WmiObject Win32_LogonSessionMappedDisk. A workaround for persistent mappings is to run Get-ChildItem Registry::HKU*\Network*. This does not include temporary mappings (in my particular example it was created through explorer on an administrator account and I did not select "Reconnect at sign-in") Is there a direct/simple way for Administrator to view connections of any user (short of a script that runs under each user context)? I have read Some Programs Cannot Access Network Locations When UAC Is Enabled but I do not think it particularly applies. I have seen this answer, but it still does not address non-persistent drives How can I tell what network drives users have mapped?

  Read the article

• Security implications of adding www-data to /etc/sudoers to run php-cgi as a different user

  - by BMiner

  What I really want to do is allow the 'www-data' user to have the ability to launch php-cgi as another user. I just want to make sure that I fully understand the security implications. The server should support a shared hosting environment where various (possibly untrusted) users have chroot'ed FTP access to the server to store their HTML and PHP files. Then, since PHP scripts can be malicious and read/write others' files, I'd like to ensure that each users' PHP scripts run with the same user permissions for that user (instead of running as www-data). Long story short, I have added the following line to my /etc/sudoers file, and I wanted to run it past the community as a sanity check: www-data ALL = (%www-data) NOPASSWD: /usr/bin/php-cgi This line should only allow www-data to run a command like this (without a password prompt): sudo -u some_user /usr/bin/php-cgi ...where some_user is a user in the group www-data. What are the security implications of this? This should then allow me to modify my Lighttpd configuration like this: fastcgi.server += ( ".php" => (( "bin-path" => "sudo -u some_user /usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) ) ...allowing me to spawn new FastCGI server instances for each user.

  Read the article

• erlyvideo server doesn't start automatically after reboot

  - by electroid

  I have installed erlyvideo server on ubuntu 9.10 karmic koala. Everything works fine, but after server reboot I have to start erlyvideo server manually with /etc/init.d/erlyvideo start. I try allready update-rc.d and I think erlyvideo by default should start automaticaly. Any help will be appreciated. Here erlyvideo startup script located in /etc/init.d/erlyvideo: #!/bin/sh ### BEGIN INIT INFO # Provides: erlyvideo # Required-Start: $local_fs $network # Required-Stop: $local_fs $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the erlyvideo streaming server # Description: starts the erlyvideo using erlang system ### END INIT INFO case "$1" in start) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; stop) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; soft-restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; upgrade) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reconfigure) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reboot) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; ping) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; console) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach-erl) cd /opt/erlyvideo && ./erts-5.8.4/bin/erl -name [email protected] -remsh [email protected] ;; *) echo $"Usage: $0 {start|stop|restart|soft-restart|upgrade|reboot|ping|console|attach}" exit 1 esac exit 0 And I have found S91erlyvideo in /etc/rc2.d next to S91apache2 which starts just fine on every reboot.

  Read the article

• What program sent which packet to the network [closed]

  - by Erik Johansson

  I would like to have a tcpdump like program that shows which program sent a specific packet, instead of just getting the port number. This is a generic problem I've had on and off sometimes when you have and old tcpdump file lying around you have no way to find what program was sending that data.. The solution in how i can identify which process is making UDP traffic on linux ? is an indication that I can solve this with auditd, dTrace, OProfile or SystemTap, but doesn't show how to do it. I.e. it doesn't show the source port of the program calling bind().. The problem I had was strange UDP packets, and since those ports are so short lived it took me a while to solve this issue. I solved this by running an ugly hack similar to: while true; date +%s.%N;netstat -panut;done So either a method better than this hack, a replacement for tcpdump, or some way to get this info from the kernel so I can patch tcpdump. EDIT: This was asked on superuser "tracking what programs sends to net", no good solution though.

  Read the article

• How important is dual-gigabit lan for a super user's home NAS?

  - by Andrew

  Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

  Read the article

• Knowledge and user generated content management system to track files, research, proposals, etc.?

  - by Eshwar

  I'll try keep it short. Here's the scenario: We have employees all over the world performing similar work i.e. research, generating powerpoint slides, word documents, graphics, etc. Many times a lot of this previous work can be reused for another future project. The current arrangement is email and phone calls which as you would agree is quick if you know where to look but otherwise archaic and very very inefficient. So I am looking for software that will allow me to do the following: Tag files e.g. an investor presentation on cellphone usage in kenya would be tagged investor, cellphone, kenya Manage references e.g. if we read something on the internet, should be able to paste that link in some fashion and tag it as above. Preferably cloud based so that it can be accessed by anybody and additionally would be nice (though NOT must) to have access levels (director, manager, everyone) A nice interface that non technically savvy folks can warm up to ;) A desktop app would be handy so that people don't always have to click upload or something A tree based system is inefficient in this case because content is usually linked across branches and also people might not quite agree on one format of a tree. Tagging works around this very nicely. What I have considered so far: Evernote (for its more professional look) Springpad (for its versatility with content) Mendeley (this is a research manager and in some ways ideal, but i fear its limited to PDFs) The goal is that when somebody wants to look for a document, they don't have to ask a colleague, they can just search with keywords and all relevant information shows up. Thanks!

  Read the article

• What was your biggest waste of money, and what should you have bought instead? [closed]

  - by rob

  I waste a lot of money on computer equipment and other electronics that I don't really need. I've also bought software that I've never really used, or which as been replaced by better free software. As I'm buying things, it doesn't seem like much--fifty bucks here, a hundred dollars there. But when I go back and look at how much I've spent over my past few electronics purchases, I usually start to think of the other things I could have bought with that money instead. Most of the computer hardware and electronics don't usually improve my life by much, if at all. Case in point: back when I was in college, I prided myself on getting the best deals for computer hardware, but when I went back and added up all the money I had spent, I had probably wasted close to a thousand dollars on "cheap" $100 hard drives that eventually all went bad (including the warranty replacements). Even if they did still work, it would not be worth the effort to use them, because they're too small and too noisy by today's standards. I've also spent thousands more on other junk, such as RAM and CPU upgrades that only gave modest performance jumps, and wireless audio transmitters that I used for a short time to stream music from the now-defunct Yahoo! Music service. Every time I see a really great deal on RAM or video cards, I come one click away from buying them, but these days I'm usually able to resist. I've been wanting to get into woodworking ever since I moved into my house, and five years later I'm finally saving up for a $600 table saw. Sure, I've already got a toolbox and a couple of the essential power tools like a drill and a jigsaw, but I can't help but think that I'd have an entire shop full of woodworking tools and a lot of nice wood furniture if I hadn't wasted all that money back in college. What has been your biggest waste of money on computer stuff and technology? If you had all that money back, would you make the same mistake again and buy the same types of things, or would you spend it on something else?

  Read the article

• Cannot access shares via full domain name on Server 2008R2

  - by Stu

  Hi, I have a strange issue. We have a 2008R2 PDC and BDC. I can join the domain fine and everything seems "normal". However, on some of the other 2008R2 servers, I am unable to do things like a gpupdate. When I try, I get an error that the clocks are wrong (they aren't) and that I don't have permission. So far, this has only affected our 2008R2 servers -- the Win 7 clients are fine. The really strange things is if I browse to: \\mydomain.lan\sysvol - I get the error. But! if I browse to: \\MYDOMAIN\sysvol - it works fine. I can also access the \hostname.domain\sysvol remotely for each of the DC's and it's fine. So in short, it appears the permissions are fine since I can access them all individually on the same account. It also seems unlikely it's on the server as most clients can access it fine. The only drama I have is when I try to use the full domain name (which of course gpupdate does) on a 2008R2 server. Also, it's not just sysvol...netlogon has the same issues too on the affected machines. Any ideas? Thanks! Drew

  Read the article

• How can I proxy multiple LDAP servers, and still have grouping of users on the proxy?

  - by Chris

  I have 2 problems that I'm hoping to find a common solution to. First, I need to find a way to have multiple LDAP servers (Windows AD's across multiple domains) feed into a single source for authentication. This is also needed to get applications that can't natively talk to more than one LDAP server to work. I've read this can be done with Open LDAP. Are there other solutions? Second, I need to be able to add those users to groups without being able to make any changes to the LDAP servers I'm proxying. Lastly, this all needs to work on Windows Server 2003/2008. I work for a very large organization, and to create multiple groups and have large numbers of users added to, moved between, and removed from them is no small task. This normally requires tons of paperwork and a lot of time. Time is the one thing we don't normally have; dodging the paperwork is just a plus. I have very limited experience in all this, so I'm not even sure what I'm asking will make sense. Atlassian Crowd comes close to what we need, but falls short of having it's own LDAP front end. Can anyone provide any advice or product names? Thanks for any help you can provide.

  Read the article

• How to resolve virtual disk degraded in Windows Server 2012

  - by harrydev

  I am using the new Storage Spaces feature in Windows Server 2012. I have the following disks: FriendlyName CanPool OperationalStatus HealthStatus Usage Size ------------ ------- ----------------- ------------ ----- ---- PhysicalDisk2 False OK Healthy Auto-Select 2.73 TB PhysicalDisk3 False OK Healthy Auto-Select 2.73 TB PhysicalDisk4 False OK Healthy Auto-Select 2.73 TB PhysicalDisk5 False OK Healthy Auto-Select 2.73 TB There is also a separate OS disk. The above disks are part of a single storage pool: FriendlyName OperationalStatus HealthStatus IsPrimordial IsReadOnly ------------ ----------------- ------------ ------------ ---------- Pool OK Healthy False False Within this storage pool some virtual disks are defined, see below: FriendlyName ResiliencySettingNa OperationalStatus HealthStatus IsManualAttach Size me ------------ ------------------- ----------------- ------------ -------------- ---- Docs Mirror OK Healthy False 500 GB Data Mirror Degraded Warning False 500 GB Work Mirror Degraded Warning False 2 TB Now the virtual disks are all running normal 2-way mirror, but two of the virtual disks are degraded. This is probably because one of the physical disks was offline for a short period of time. However, now the virtual disk cannot be repaired, even though, all physical disks are healthy. There is plenty of available space in the storage pool. This I cannot understand so I was hoping for some help, on how to resolve this? Below I have listed the full output from the Get-VirtualDisk CmdLet for the "Work" disk: ObjectId : {XXXXXXXX} PassThroughClass : PassThroughIds : PassThroughNamespace : PassThroughServer : UniqueId : XXXXXXXX Access : Read/Write AllocatedSize : 412316860416 DetachedReason : None FootprintOnPool : 824633720832 FriendlyName : Work HealthStatus : Warning Interleave : 262144 IsDeduplicationEnabled : False IsEnclosureAware : False IsManualAttach : False IsSnapshot : False LogicalSectorSize : 512 Name : NameFormat : NumberOfAvailableCopies : 0 NumberOfColumns : 2 NumberOfDataCopies : 2 OperationalStatus : Degraded OtherOperationalStatusDescription : OtherUsageDescription : Disk for data being worked on (not backed up) ParityLayout : PhysicalDiskRedundancy : 1 PhysicalSectorSize : 4096 ProvisioningType : Thin RequestNoSinglePointOfFailure : True ResiliencySettingName : Mirror Size : 2199023255552 UniqueIdFormat : Vendor Specific UniqueIdFormatDescription : Usage : Other PSComputerName :

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• MacOS creates a new mount on AFP path calls

  - by jAndy

  Hi Folks, following scenario: In my webapp, my customers are using Firefox as target browser. They have the need to open afp:// folders via Javascript. To make a long story short, this really works. You need to setup Firefox with about:config and set the value network.protocol-handler.external.afp to true. What happens then, the operating system (OSX) takes care of that path and it correctly opens a Finder window. The problem: OSX does create a new mount every time. It cannot distinct between afp://host/path/111 and afp://host/path/222 for instance. Furthermore, even if the afp path is 100% identical a new mount is created. It looks like this is the default behavior from OSX regardless of Firefox. So, is there any chance I can tell OSX not to create a new mount for some sub directorys which should get access over afp:// ? update: It looks like, there are OSX applications which can change the default behavior for network protocols. So you can change "somewhere" which application OSX should call for a protocol. If that is true, wouldn't it be possible to create a script which just opens the local path without a afp:// prefix ? The question here is, where is that configuration (?) to tell OSX which application to use for specific protocol. Any help welcome!

  Read the article

• xauth, ssh and missing home directory

  - by flolo

  We have several servers, and normaly everything works fine, except now... we get a new aircondition installed. This takes 36 hours and for this time almost all servers got shutdown, only 2 remaining servers run for the most important tasks (i.e. accepting incoming email, delivering some important websites, login-server). Everybody was informed that when they need appropiate data from the homedirs they should fetch it before take down. Long story short: Someone realized that he have run a certain program on one of the servers. No Problem, he can remote login into our login server and run the programm there without home directory (binaries are local and necessary information can be copied to the /tmp). That works like a charm until... ... the user needs to run a GUI programm. I find no easy way to make it running, usually ssh -Y honk@loginserver is enough but now the homedirectory is missing and ssh is not able to copy the cookies into ~/.Xauthority (as the file server with the home directories is down). Paranoid as all systemadmins all X-Server just listen locally not on tcp ports, so no remote X connection possible SSH config is waterproof - i.e. no way to set environment variables. My Problem is, that the generated proxy MIT cookie from ssh get lost as the .Xauthority doesnt exist. If I could retrieve it somehow I could reenter it a .Xauthority in /tmp. The only other option (besides changing the config) which came to my mind is, makeing a tunnel (netcat, or better ssh) from the remote host to the loginserver and copy the cookie manually (not sure if it the tcp-unix domain socket stuff works as expected). Any good suggestions (for the future - now our servers are already up)?

  Read the article

• Prevent Windows from resizing all the apps on the desktop when switching monitors

  - by Greg Hewgill

  Short version: When moving my laptop and sleeping between using different monitors, all my open windows are crammed into the upper left corner as if they tried to fit on the laptop internal screen resolution. I plug in and switch to the external monitor before unlocking my session. Is there a way to prevent this automatic resizing? Longer version: I have a laptop that I move between two locations. I have one docking station, and the same kind of monitor configured for 1600x1200, in both locations. The internal laptop screen is awful so I don't use it. Location A: Docking station, monitor connected via DVI. Location B: No docking station, external monitor connected via VGA cable. In this location I have the laptop lid open for keyboard access but I don't use the laptop screen. When moving from Location A to Location B, the laptop wakes up from sleep, displaying the screen on the internal monitor. I switch to the external monitor display (using Fn+F8 on this laptop), and only after that do I unlock my session with my password. However, Windows has crammed all my nicely arranged windows into the upper left corner as if it were trying to fit them all on the laptop internal screen resolution. When moving from Location B to Location A, I have the laptop lid closed when using the docking station so Windows apparently concludes the screen resolution is 1600x1200 and doesn't resize any windows. The laptop is a Dell Latitude running Windows 7 Professional.

  Read the article

• Is it possible for a faulty processor to cause audio static/noise?

  - by Tom

  I have a Core 2 Extreme processor I received from a friend and have set up an XBMC box using it. However, I constantly get audio static whenever playing any music or videos. Here is a video of the sound: http://www.youtube.com/watch?v=SqKQkxYRVA4 I have tried replacing everything short of the case and the processor, including cables, audio interfaces, operating systems, ram, etc, leading me to think it might be either the case shorting out the motherboards I have tried or a faulty processor. Is it possible for a faulty processor to cause audio static/noise? Any feedback would be appreciated. Edit - Here's a list of things I have tried: Reinstalling OS Installing/upgrading/repairing PulseAudio/Alsa Installing alternate OSes, straight Ubuntu, Lubuntu, Xubuntu, Arch, Mint, Windows 7 Switching audio from the external card to internal Optical, audio out through HDMI, audio out through headphones Different ports on receiver (my main desktop sounds fine on the same sound system) Different optical cables Unplugging everything unnecessary from the motherboard (1 HD, 1 Stick of Ram, 1 Keyboard) Swapping out ram Swapping out the motherboard Replacing the Graphics Card (was replaced due to fan being noisy, not specifically for this problem) Different harddrives Swapping power supply Disabling onboard audio Switching Power Cable Plugging in through surge protector Plugging into different outlet on separate circuit

  Read the article

• How to find out what is causing a slow down of the application on this server?

  - by Jan P.

  This is not the typical serverfault question, but I'm out of ideas and don't know where else to go. If there are better places to ask this, just point me there in the comments. Thanks. Situation We have this web application that uses Zend Framework, so runs in PHP on an Apache web server. We use MySQL for data storage and memcached for object caching. The application has a very unique usage and load pattern. It is a mobile web application where every full hour a cronjob looks through the database for users that have some information waiting or action to do and sends this information to a (external) notification server, that pushes these notifications to them. After the users get these notifications, the go to the app and use it, mostly for a very short time. An hour later, same thing happens. Problem In the last few weeks usage of the application really started to grow. In the last few days we encountered very high load and doubling of application response times during and after the sending of these notifications (so basically every hour). The server doesn't crash or stop responding to requests, it just gets slower and slower and often takes 20 minutes to recover - until the same thing starts again at the full hour. We have extensive monitoring in place (New Relic, collectd) but I can't figure out what's wrong; I can't find the bottlekneck. That's where you come in: Can you help me figure out what's wrong and maybe how to fix it? Additional information The server is a 16 core Intel Xeon (8 cores with hyperthreading, I think) and 12GB RAM running Ubuntu 10.04 (Linux 3.2.4-20120307 x86_64). Apache is 2.2.x and PHP is Version 5.3.2-1ubuntu4.11. If any configuration information would help analyze the problem, just comment and I will add it. Graphs info phpinfo() apc status memcache status collectd Processes CPU Apache Load MySQL Vmem Disk New Relic Application performance Server overview Processes Network Disks (Sorry the graphs are gifs and not the same time period, but I think the most important info is in there)

  Read the article

• Why do I have to log into hotmail twice?

  - by Tony Lee

  I just recently noticed I have to attempt a login into hotmail twice before it succeeds. Although I'm using Google Chrome (3.0.195.21), the symptoms are well described in a Mozilla thread. In short, I'm told: The e-mail address or password is incorrect. Please try again. The thread on mozilla's site that supposed to describe the latest details (and the 1st hit on google when I search for "hotmail login twice") requires an account to read so I'm hoping someone here has a good synopsis of what the cause is. I normally start at hotmail.com, which redirects to login.live.com/.... I can login by starting at mail.live.com, using IE8 or attempting a 2nd login. Oddly, if I start at login.live.com Chrome tells me there is a redirect loop. Does anyone know or have a public link to the root cause of the double login? (it is a hotmail account I'm login into) EDIT - Caused by my 'restricting how 3rd parties can use cookies'. If I allow all cookies, it works first time.

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• Users removing Administrator from files/folders permissions

  - by user64204

  We're running Windows Server 2003 R2 with Active Directory and are having an issue with network shares whereby users, in an attempt to secure their documents, remove everybody (including the Administrator account) from their files/folders permissions. Since the Administrator no longer has read permission to them, we can't even backup files manually as we get permission errors. One solution that we've found is to change the owner of the files and directories to the Administrator account. We can then change the permissions as we wish. The problem is that this has to be done manually so can't really be applied to an entire share. Another solution that we've tried is to use cacls as follows: cacls d:\path\to\share /C /T /E /G Administrator:F The problem with this is that we're still getting an ACCESS DENIED error on files/folders on which Administrator was removed. Q1: Is there a way to restore at least read access to all files/folders to the Administrator account in a recursive fashion? That would be for the short term. For the long term we're looking for a solution to prevent users from removing Administrator from files/folders permissions. Since we're going to migrate to Windows Server 2008 R2 soon we could wait until we've migrated to implement such solution if need be. Q2: Is there a way to prevent users from removing Administrator from files/folders permissions on Windows Server 2003/2008?

  Read the article

• Block SMTP session with sender domain which doesn't itself accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the declared sender's domain has an MX which refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. Note that I'm not, as some commenters have assumed, talking about checking whether the SMTP client will receive messages. The check I want is whether the declared sender's domain (regardless of who the current SMTP client is) will accept SMTP connections from here. In other words: when we get around to sending a message back, we'll need the sender's domain to accept SMTP connections; I want to do that check before accepting the incoming session. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• Which AMI to to use for Java/Tomcat/MySQL in Amazon EC2?

  - by Justin

  I originally posted this on stackoverflow.com and it was suggested serverfault.com might be a better place to ask this question. So here goes: I'm trying to determine which Amazon Machine Image (AMI) to use as my Virtual Server in Amazon's EC2. For now, I'll need to choose an AMI that complies with the AWS Free Usage Tier. I want to deploy a Java app that I've been developing using Eclipse on Windows XP, Tomcat 7 and MySQL 5.5. I'm aware that I can choose the Basic 32-bit Amazon Linux AMI. Then I'd manually install Tomcat and MySQL (does MySQL get installed on the image or separately on an Elastic Block Store (EBS)?). Here's the rub, I'm a bit of a Linux noob. I can start Tomcat and tail the logs and such on Linux but I'm not familiar with the install process for Tomcat and MySQL on Linux and commands like sudo and chmod. I'm happy to get more hands on with Linux but I'm short on time right now. Are there AMI's that already have Tomcat and MySQL bundled? The Request Instance Wizard shows 805 Community AMI's that are Free Tier Eligible. 51 of the Free Tier Eligible AMI's have "Tomcat" in their name. I'm willing to consider using Elastic Beanstalk but my research thus far hasn't found any discussion of using MySQL with Beanstalk. The discussions all seem to use Amazon's SimpleDB. Any advice is greatly appreciated.

  Read the article

• Get Safari to use different autocompletion on different URLs on same hostname

  - by Luke404

  I have a webserver publishing different services over the same SSL VirtualHost, the two most commonly used being PhpMyAdmin and Cacti. These (and others) use 'cookie' style authentication, asking user and password in an HTML form (thus not using HTTP Authentication). Being on the same hostname, the Safari browser didn't manage too well stored passwords: if I login to one app with user foo, and then go to app two it would propose me user foo and its password in the login form. Changing just the username to bar used to be sufficient to let Safari autocomplete the correct password in its form field. Annoying, but I could live with it - usernames are short and easy to remember when compared to the passwords we use. After the update to safari5 this seems to be no longer true: if I store in safari (actually user keychain on OSX) credentials for https://www.foobarbaz.com/app1 AND credentials for https://www.foobarbaz.com/app2 there seem to be no way for it to autocomplete both based on the url. Even editing the keychain to add the path (it will store only the hostname by default) does not help. Is there anything I can do to let it work the way I want while still keeping everything on one hostname? Modifying anything server side is of course possible, but I can't switch apps to HTTP Auth (and not every one will support it anyway) to use different 'realms'.

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >