Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 161/343 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

  • IPv6 - Public IPs, private IPs, IPs derived from the MAC address? Confused!

    - by sinni800
    I'm pretty much excited for IPv6 because of the large address room and (potential?) owning of more than one IP, or even tens of IPs (/122 subnet?) Though one magazine has now confused me. In a current issue (no. 3) of "CT", a German computer magazine, I read that when using IPv6 your IP address consists of your MAC address and various other things, and that this address will be public on the web, no matter what access point / LAN you connect to. My knowledge of IP(v6) is in contrary of this. I thought you will normally always have a a local network IP and NAT takes care of your Internet access, and your provider gives the NAT router an IP. I've heard of the 6to4 interface, but does this one give you your own ip in the IPv6 net? Personally I hope it still is through a personal IP space (like 192.168, 127.16-31, 10. in IPv4) in private networks with a NAT going to the Internet. And also I hope that providers will offer subnets to private customers so they don't have to use NAT anymore. Yay for converting your LAN into the WAN and using better security (so Computers from the same subnet still get access rights like normal).

    Read the article

  • Monitoring/logging a malfunctioning internet connection

    - by Pekka
    I have a mysterious internet connection problem: Every 15-20 minutes, the connection will become very slow, and take 2-3 minutes for anything to load. I've had a technician from the ISP over here to test the hardware, and everything is in pristine condition. They have no other explanation than a configuration error on my machine, a possibility I can exclude 90% because I'm experiencing the same problems with another machine. I will have to monitor the situation now, and I would like to run a program that logs when internet connections become slow. I thought about putting something together using at and wget. Does anybody know of some other tool for this that does this out of the box - maybe something with an adjustable request frequency, logging connection speeds etc.?

    Read the article

  • Optimizing wireless router speed and minimizing interference.

    - by Tchalvak
    I've been experiencing problems with my wireless connectivity lately, and want to make sure that it's not related to the abundance of other wireless routers here in my building. So, what I'm looking for is a method (probably via some application or another) to audit the wireless channels (and other factors that might be important that I don't even know of yet) that are floating through the aether around me. Ubuntu or other linux apps are preferred, but some kind of windows/mac solution is possible, since I do have other OSes around me that I could install & test on. Router: netgear WGT624 v3 Hearsay tells me that channels 1, 6, and 11 are "non-overlapping" (I expect they aren't used for non-wireless-router purposes or something, not sure how they couldn't overlap with other routers using other channels), so perhaps my best choices of channel are limited, so if channels aren't really a big concern, I'd be happy to get links to other optimizations that I should look into.

    Read the article

  • AuthInfoRequired cups overwrites

    - by mooscape
    My problem is basically identical to the following: http://bbs.archlinux.org/viewtopic.php?id=61826 Put simply, I have a machine in ubuntu trying to connect to another ubuntu machine via a network in order to use the printer attached. There is no problem printing until I restart the guest machine. Immediately it overwrites the printers.conf file (under /etc/cups/printers.conf). It always adds the same line: AuthInfoRequired username,password I stop cups and change it to *#*AuthInfoRequired username,password to comment out the command. Start cups. Works great 'til the next shutdown. Then it gets overwritten again. Googling indicates it may be GTK problem and not CUPS, but I have found no permanent solution to date. Any suggestions appreciated ....

    Read the article

  • Connection two wireless ADSL routers to share IPs

    - by user35218
    I have two wireless ADSL routers sitting right next to each other, each with his own internet connection. I'd like to be able to connect to a computer that is connected to router A from a computer that is connected to router B, while keeping both routers internet connection individually. i.e. If computer A is connected to router A, it will use router A internet connection, and a second computer, call it B, will be connected to router B, and will use router B internet connection. Is this possible?

    Read the article

  • Barebones network appliance, 4+ GbE NICs, Intel chipset

    - by gravyface
    Looking for a stepped-up ALIX or Soekris embedded network appliance to load pfSense and/or handle other FOSS-based network roles. Main criteria is a GbE NICs (will be used for core routing/firewalling with managed GbE switches), DDR3 RAM capable, and multi-core/Intel Atom processor, in a 1U rack-mountable case or smaller. Axiomtek has the ideal product but I don't think they have retail channels.

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Packet loss with all adapters on one PC only on the LAN

    - by Enigmativity
    I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

    Read the article

  • How do I configure a secondary gateway in RHEL5?

    - by Brett Ryan
    Greetings, we have been experiencing a random timeout issue with VPN users connecting to one of our servers which is causing a problem. My network administrator has instructed me to configure a secondary gateway to include the VPN connection. My current connection resides as follows, 10.1.9.1 is the internal gateway to the internet, I'd like to add 10.1.1.20 as the VPN gateway. # Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet DEVICE=eth0 BOOTPROTO=none BROADCAST=10.1.255.255 IPADDR=10.1.1.22 IPV6_AUTOCONF=yes NETMASK=255.255.0.0 NETWORK=10.1.0.0 ONBOOT=yes GATEWAY=10.1.9.1 TYPE=Ethernet USERCTL=no IPV6INIT=no PEERDNS=yes

    Read the article

  • Adding a Printer to my Print Server Failing

    - by Rudi Kershaw
    So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

    Read the article

  • Is there a way to turn off the sound that plays when my computer reconnects to the wireless network?

    - by Dan Tao
    I know this seems silly. Obviously I could mute my computer, or turn the speakers off. But it seems like surely there should be a way that I can keep all of my normal computer sounds without having to hear this one sound (no, it doesn't really bother me; mostly my wife just wants me to turn it off because she finds it annoying). I tried right-clicking on the volume icon in the notification area and went through all of the sounds in the list, thinking I could find the one offending noise and just turn it off. But none of them seem to correspond to the sound that plays when my wireless adapter randomly disconnects and reconnects to the wireless network.

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • Does an unmanaged 4/8-port GBit Ethernet switch with a GBIC port exist?

    - by Aaron Digulla
    I'm looking for a simple unmanaged switch with 4-8 GBit Ethernet ports and a fiber port (either as a GBIC slot or pre-installed with a 1000BASE-SX port). Does something like that exist? [EDIT] I want to connect to places in my home without drilling large holes though the floors. Therefore, I'm looking for a cheap way to connect two GBit switches via fiber. I tried with a media converter (GBit <- multimode fiber) but that costs about 50% throughput. So I was hoping that there is a cheap, small GBit switch which has a GBIC slot). All I found so far are very expensive managed switches with 12 or 24 ports for industry use.

    Read the article

  • Vlans and subinterfaces

    - by Adeodatus
    I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Internet connection very slow after Linksys configuration

    - by NLV
    Hello We have this network setup Server1 - DHCP server, Domain Controller, AD Lease line for Internet connection From lease line to Linksys router (we dont use wireless though) From linksys to Netgear (24 port Switch) and vonage (VoIP) Netgear to all our machines We configured Linsys with the static IP and DNS server addresses our ISP gave and we have routed it correctly. All our work machines are configured with Get IP automatically DNS server addresses our ISP gave The problem is that none of the sites are getting opened promptly. It is taking around 5 minutes to load google.com. But we are able to ping all the sites. What could be the problem?

    Read the article

  • Vista laptop 1 connects to network but Vista laptop 2 doesn't

    - by Jaips
    (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

    Read the article

  • Simulating a low-bandwidth, high-latency network connection on Linux

    - by Justin L.
    I'd like to simulate a high-latency, low-bandwidth network connection on my Linux machine. Limiting bandwidth has been discussed before, e.g. here, but I can't find any posts which address limiting both bandwidth and latency. I can get either high latency or low bandwidth using tc. But I haven't been able to combine these into a single connection. In particular, the example rate control script here doesn't work for me: # tc qdisc add dev lo root handle 1:0 netem delay 100ms # tc qdisc add dev lo parent 1:1 handle 10: tbf rate 256kbit buffer 1600 limit 3000 RTNETLINK answers: Operation not supported How can I create a low-bandwidth, high-latency connection, using tc or any other readily-available tool?

    Read the article

  • Cannot access server shares over VPN

    - by DuncanDavies
    I've set up a single hosted server to use as a development environment for a web-based application. The web app is served up fine on port 80, however I'm struggling to get my VPN to behave how I'd expect so the developers don't have the access they require. The VPN connects fine and I can access the back-end database (SQL Server) which resides on the server with the client tools from the laptops. However they cannot access any shared folders. The server's local IP address is 10.x.x.x, and I've assigned a static IP address pool to RRAS (of 192.168.100.1 - 20). The clients pick up a valid IP Address (i.e. 192.168.100.9) when they connect. There is no name resolution setup, DNS or WINS. When connected via VPN the clients can ping the server (192.168.100.1) by IP Address, but cannot map a drive to a shared folder (net use * \\192.168.100.1\xxxxx) - I get 'System error 53 has occurred. The network path was not found.' I don't understand why I can ping by the ip, but not map by it. Some details: Server OS is Windows 2008 (Datacenter) VPN is SSTP using RRAS Clients are all Windows 7 I've tried temporarily disabling the firewalls So, why can we not access the file system when everything else (ping, RDP, SQL Server clients tools) works? Thanks for your help Duncan

    Read the article

  • Setting up router: I can get online via Ethernet, and I can connect to router wirelessly, but can't

    - by Gabe
    I'm setting up a new D-Link N300 router, and trying to connect a MacBook Pro and a MacBook, both running OS X 10.6. As the question says, either computer can connect to the internet when connected to the router via Ethernet. And either one can get on the router's wireless network. But when connected wirelessly (without the Ethernet cable plugged in), neither one can get online. I can't figure out why that would be. Any help appreciated.

    Read the article

  • With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

    - by larsks
    I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

    Read the article

  • My DNS cannot resolve an web site address?

    - by ipkiss
    Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me please? Thank you.

    Read the article

  • Network topology question

    - by Asbie
    We currently have three networks, X.X.163.1, X.X.93.1 and 192.168.1.1. Today's setup is like this: http://i.imgur.com/tkKWy.jpg We now have PPT VPN from internet to the X.X.163.1-network, but really need to access the files from the File Server through VPN. I am also aware that this setup is not optimal. So please, any advices on how to redesign our network? Rack servers are mostly web and db servers, with only public IP addresses.

    Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >