Search Results

Search found 16455 results on 659 pages for 'hosts allow'.

Page 164/659 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

  • Cisco ASA - Enable communication between same security level

    - by Conor
    I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

    Read the article

  • Enable: Asp.net connection pool monitoring with performance monitor

    - by BlackHawkDesign
    If this question is at the wrong forum, be free to tell me. I'm a c# developer, but I'm running in a system management issue here. Intro: Im suspecting that an asp.net application is having some issues with the connection pool and that the pool is flooding from time to time. So to make sure, I want to monitor the connection pool. After some searching I found this article : http://blog.idera.com/sql-server/performance-and-monitoring/ensure-proper-sql-server-connection-pooling-2/ Basicly it explains stuff about connection pools and how you can monitor the application pool with performance monitor. The problem: So I logged in to the asp.net server(The sql database is hosted on a different server) which hosts the website. Started performance monitor. But when I want to select 'Current # pooled and nonpooled connections', I have no instance to select. There fore I can't add it. Question How can I create/supply an instance so I can monitor the connection pool? Thanks in advance BHD

    Read the article

  • Plesk 10 Postfix with multiple IP adresses and SSL certificates

    - by JulianB
    We are currently running a root server with Debian 6 and Plesk 10.4.4. We have some virtual hosts using one IP adress (shared) - e.g. example1.com - and another virtual host using a dedicated IP address (example2.com). Is there a way to configure postfix to do the following Always use the IP address of the virtual host to which the e-mail account belongs (so that an e-mail from [email protected] will originate from the shared IP-Address and an e-mail from [email protected] will originate from the dedicated IP? Use different certificates for TLS for example1.com and example2.com? If the latter is not possible: Could any problems arrive when using example1.com as certificate for example2.com users? Of course, example2.com users would have to configure their clients to use example1.com as the SMTP server name to avoid annoying security warnings. But if we still would be able to get the effect of the first point that would still be acceptable.

    Read the article

  • Nagios - NagWin - Send notification with gmail

    - by Attila Bujáki
    I would like to send Nagios notifications using my gmail account. I have already set up my hosts I want to monitor and services also. What is the most simple way to accomplish this using NagWin on a Windows Server 2012 installation? As far as I know I must change some of these configuration settings: # 'notify-host-by-email' command definition define command{ command_name notify-host-by-email command_line /usr/bin/printf "%b" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\nHost: $HOSTNAME$\nState: $HOSTSTATE$\nAddress: $HOSTADDRESS$\nInfo: $HOSTOUTPUT$\n\nDate/Time: $LONGDATETIME$\n" | /bin/blat - -to $CONTACTEMAIL$ -f nagios@localhost -subject "** $NOTIFICATIONTYPE$ Host Alert: $HOSTNAME$ is $HOSTSTATE$ **" -server ??? } # 'notify-service-by-email' command definition define command{ command_name notify-service-by-email command_line /usr/bin/printf "%b" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\n\nService: $SERVICEDESC$\nHost: $HOSTALIAS$\nAddress: $HOSTADDRESS$\nState: $SERVICESTATE$\n\nDate/Time: $LONGDATETIME$\n\nAdditional Info:\n\n$SERVICEOUTPUT$\n" | /bin/blat - -to $CONTACTEMAIL$ -f nagios@localhost -subject "** $NOTIFICATIONTYPE$ Service Alert: $HOSTALIAS$/$SERVICEDESC$ is $SERVICESTATE$ **" -server ??? } What should I use for smtp server? Is it possible to directly send my notifications to the Gmail server?

    Read the article

  • 127.0.0.1 is working but localhost is not working on mac XAMPP

    - by Ganim
    I installed XAMPP on my mac months ago and was working great. Now i get "Test Page For Apache Installation" when i try to browse /localhost and /localhost/xampp is not found. But when i browse /127.0.0.1 it just works as localhost used to be. I double checked my /etc/hosts file that i have 127.0.0.1 localhost and not commented. Also when i browse localhost/~username/test.php , i get contents of test.php: <?php echo 'ganim'; ?> but if i browse 127.0.0.1/~username/test.php , i get: ganim what could change redirecting of localhost or how can i get localhost work again?

    Read the article

  • Cannot connect remote mysql, Cpanel?

    - by BerkErarslan
    I use centos and cpanel I need to use remote mysql with php. I add the ip which I try connect to server to "Remote Database Access Hosts" on Cpanel. However, when I try to connect server with this code: <?php $link = mysql_connect("server_ip", "xxx", "xxx") or die(mysql_error()); $db = mysql_select_db("xxx", $link) or die (mysql_error()); print_r($db); I have error like this: Warning: mysql_connect() [function.mysql-connect]: Can't connect to MySQL server on 'xxxx' (10060) in C:\AppServ\www\test.php on line 3 Can't connect to MySQL server on '94.138.204.234' (10060) I also try to connect using "server_ip:3306" but it still doesn't work. How Can I solve this problem ?

    Read the article

  • Is using Capistrano for user maintenance tasks on university lab feasible?

    - by danielkza
    I've been looking around for tools to replace some legacy scripts for creating and maintaining accounts in a university computer lab ecosystem consisting of things like: LDAP and Kerberos for authentication User home storage and web pages Entries on an SQL database Printing quotas Mailing lists, etc. I'd also like to automate machine and VM membership for Kerberos and Puppet if possiible. I've found Capistrano, and while the basic principle of running tasks on remote hosts through SSH seems to fit, and the DSL in Ruby looks quite nice, I've found most documentation is related to application deployment, not generic tasks. I'm also not aware of any good way to parameterize tasks so I can pass on the user information for creation. Is something about Capistrano I am missing, or is it not the correct tool for this job? Are there any more userful alternatives?

    Read the article

  • Internal users can't receive email sent by application

    - by jdballard
    We have an application server that hosts a CRM application. It is using SMTP on it's own server to send emails. If I send an email using the application to [email protected], it shows up in my inbox. If I send an email to [email protected], it never shows up. It doesn't matter what address I put in for @MyCompanyDomain.com, they never get through. Any email addresses outside our domain/firewall get through. We're using Exchange 2007 and when I look at the message tracking logs, the missing messages don't show up there, either. Is there something I need to configure in Exchange or the SMTP server on the application server? I can't figure out why emails get outside the firewall but internal emails never show up. Thanks, Jeff

    Read the article

  • Force Windows 7 to pin a file with no extension to the Jump List for Notepad

    - by Greg Bray
    I want to add the "C:\Windows\System32\drivers\etc\hosts" file to the Jump List for notepad.exe on a Windows 7 machine, but since the file does not have an extension there is no default program associated with it. This means it never shows up in the recent list and you also cannot drag it to the task bar to manually pin it to the start list. I've had problems with jump lists before, and there are ways to use the Registry or File system to change how Jump Lists work, but I haven't seen anything to manually edit a jump list yet. Is there any way to force an item to be pinned to the jump list when that item does not have a program associated with it?

    Read the article

  • Update mysql database with arpwatch textfile database

    - by bVector
    I'm looking to keep arpwatch entries in a mysql database to crossreference with other information I'm storing based on mac addresses. I've manually imported the arpwatch database into my mysql database, but being a novice with databases I'm not sure what the best way to continually update the database with new entries without creating duplicates would be. None of the fields can be unique, as even the time is duplicated frequently. I'm not interested in the actual arpwatch events like flip flop or new station, just the mac/ip/time pairings. Would a simple bash (or sql) shell script do the trick? Would it be possible to make the mac address plus the time be a composite key of some sort? the database is called utility, table is arpwatch, columns are mac, ip, time a seperate table named 'hosts' with columns mac, ip, type, hostname, location, notes has mac as the primary key. This table will correlate different ip addresses that a mac had over time using the arpwatch column initial import was done with MySQL Workbench using INSERT INTO commands with creative search and replace on the text file

    Read the article

  • Datacenter IP Addressing and DNS Management

    - by user65248
    Hello everyone Basically we are setting up a small Datacenter, about 300 amps power and max 50 racks, Im saying these coz I wanna u imagine the size and requirements, I have studied networking mostly Microsoft and Windows based systems , but I cant get how the IP addressing and DNS management and configuration works in a Datacenter , and unfortunately I have to setup everything by myself but defe we will have some staff to do some job. Now my questions Datacenter IP Addressing Suppose we have got a block of 200 IP addresses from our ISP, How can I manage these block of IP addresses, is there any software out there to simplify this I heard that using DHCP server in a datacenter is not recommended, otherwise what would u say about MS DHCL server ofc considering we need to have backup serversin case of failur How can I assign a block of IPs to a specific rack, I know with different software and management its different but Im asking how it is done normally IP addresses are exposed to the whole network, what if a customer try to use an IP address and is not assigned to their server or rack , how can I prevent this or how can I track the IP usage DNS Management Im goin to setup at least two servers for our DNS servers, I know nothing about Datacenter DNS system, but I have configured DNS server in normal networks and also for webservers, Now I wanna know What exactly needs to be done for a DNS in a datacenter that is not done for normal networks. How can I configure PTR records why cant I configure PTR records on my webserver side DNS server and it should be done on datacenter DNS server , I mean what is the difference in DC DNS servers that allow us to to so , I know the question is very silly and simple but Im confused Is there any software outthere to allow doing the whole thing, I mean automatically add records to the DNS and also managin IP addresses !? Thanks in advance

    Read the article

  • How can I regain control over a "stuck" scroll bar?

    - by jonsca
    I normally have a lot of tabs open in the browser at one time, which normally doesn't cause any problems. Occasionally, though, the page will have fully rendered, the scroll bar is at the top of its track on the right, but placing the the mouse pointer on the scroll bar does not allow me to get control of it (and using the arrow at the bottom of the scroll bar doesn't work either). This seems to happen to me in both Firefox and Chrome, both latest versions. There is normally no load on the CPU, and while my memory usage can be high (especially with Chrome), I still usually have 25% left. I fear that this is one of those "for your own good" features, to prevent scrolling down a page that may still have elements loading and/or a stuck script, but I'm wondering whether or not there is a setting in Firefox or Chrome (or perhaps Windows in general) that will allow the scroll bar to be "released" even though the browser may be busy? It may be "2002" of me, but I wouldn't mind being able to scroll along gradually, even if the page hasn't had time to fully render all of the images, etc., yet. Does such an advanced setting exist "under the hood"?

    Read the article

  • OpenVPN Client timing out

    - by Austin
    I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

    Read the article

  • Apache 2.4, Ubuntu 12.04 Forbidden Errors

    - by tubaguy50035
    I just installed Apache 2.4 today, and I'm having some issues getting vhost configuration to work correctly. Below is the vhost conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /hosting/Client/site.com/www ServerName site.com ServerAlias www.site.com <Directory "/hosting/Client/site.com/www"> Options +Indexes +FollowSymLinks Order allow,deny Allow from all </Directory> DirectoryIndex index.html </VirtualHost> There is an index.html file in /hosting/Client/site.com/www. When I go to the site, I receive a 403 forbidden error. The www-data group is the group on the www folder, which I've already given all permissions (r/w/x). I'm really at a loss as to why this is happening. Any thoughts? If I remove the vhost and go straight to the IP address, I get the default, "It works!" page. So I know that it's working. The error log says "client denied by server configuration". apache2ctl -S dump: nick@server:~$ apache2ctl -S /usr/sbin/apache2ctl: 87: ulimit: error setting limit (Operation not permitted) VirtualHost configuration: *:80 is a NameVirtualHost default server site.com (/etc/apache2/sites-enabled/site.com.conf:1) port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com port 80 namevhost site.com (/etc/apache2/sites-enabled/site.com.conf:1) alias www.site.com ServerRoot: "/etc/apache2" Main DocumentRoot: "/var/www" Main ErrorLog: "/var/log/apache2/error.log" Mutex watchdog-callback: using_defaults Mutex default: dir="/var/lock/apache2" mechanism=fcntl Mutex mpm-accept: using_defaults PidFile: "/var/run/apache2.pid" Define: DUMP_VHOSTS Define: DUMP_RUN_CFG Define: ENALBLE_USR_LIB_CGI_BIN User: name="www-data" id=33 not_used Group: name="www-data" id=33 not_used Ouput of namei -mo /hosting/Client/site/www/index.html f: /hosting/Client/site.com/www/index.html drwxr-xr-x root root / drwxr-xr-x root root hosting drwxr-xr-x root root Client drwxr-xr-x nick www-data site.com drwxr-xr-x nick www-data www -rw-rwxr-x nick www-data index.html

    Read the article

  • RTF File Opens as Read Only from Document Management System (Does not happen for all users)

    - by Dave
    We have a third party system in place that as one part of its duties hosts RTF files that a user can open, make changes to, and save back into the document management system. Recently we have begun upgrading users to Office 2007 from 2003. We are now hearing that when some users open these documents, they open as Read Only (even though there is no document protection in place and the files are set for Unrestricted Access). Other users though, who also have Word 2007, report no problems. There were no problems for anyone when Word 2003 was being used. I'm sure it's a setting in Word but I'm having a lot of difficulty in identifying where the issue could be. Looking for any assistance on why these RTF files are opening as Read Only for some and not for others when using Word 2007. Thanks! Dave

    Read the article

  • How can I suppress /etc/issue without losing error messages?

    - by Andy
    Is it possible to tell the ssh client to not print the connects of /etc/issue to stdout when connecting to a remote host, but to print out any other diagnostic (e.g. error) messages? Either using ssh -q or having LogLevel quiet in ~/.ssh/config suppresses the /etc/issue printing, but also turn off error messages. I've tried touching ~/.hushlogin as well - that stops /etc/motd being printed, but doesn't affect /etc/issue. The most obvious solution is just to remove /etc/issue, but company policy dictates the file be there with dire warnings about unauthorised access. This is non-negotiable. Unfortunately, I've got a bunch of scripts that run across quite a few hosts via ssh, and the log files are a) very large and b) full of legalese. Since quite a lot of stuff runs unattended, I don't want to lose any error messages that are printed.

    Read the article

  • Sporadic '.Xauthority not writable, changes will be ignored' going from OSX -> Linux

    - by Kamil Kisiel
    Every now and then when users SSH from their OS X (Snow Leopard) workstation to one of our Linux hosts they receive the message: /usr/bin/xauth: ~/.Xauthority not writable, changes will be ignored Of course, their X forwarded applications will not work at this point. However, if they log out and log right back in again they do not get the message and everything works as expected. On their Mac they get their home directory via AFP. The Linux machines get it via NFS. Any ideas on what could be going on here?

    Read the article

  • Apache2 conditional section based on port

    - by Waleed Hamra
    I don't know much about if statements in apache configuration, and I'm wondering if I can have a section of the configuration applied only if the request is received on a certain port. In short, this is about SSL. I have name based virtual hosts, I can make a configuration for port 80, then duplicate it all for port 443, and add the relevant SSL configurations. But this seems redundant. I was wondering if i can have something like: <VirtualHost *:80 *:443> and then I can put: <IfModule mod_ssl.c> SSLEngine on SSLCertificateFile ... SSLCertificateKeyFile ... SSLCACertificateFile ... </IfModule> inside an if statement that checks if connection is on port 443... or is such thing impossible? the server supports SNI, and I don't have any worries from non-SNI compliant browsers.

    Read the article

  • Getting rid of Plesk on a VPS

    - by TomA
    I've been using a relatively expensive VPS for hosting about 30 domains and I want to migrate to a cheaper one, without Plesk. Both use CentOS. My users will not care, they don't use Plesk anyway. But I will not be able to use it for creating new virtual hosts, FTP accounts etc. I'm not a commandline guru, esp. not in a server environment. Is there a free Plesk alternative for these purposes? I need to: Create a new virtual host with it's own FTP account Setup some basic FTP quota I don't need: DNS management (the new VPS service has an external DNS management GUI) Mail server management (I use Google Apps) Any suggestions welcome, from Plesk alternatives to "RTFM" or links to tutorials.

    Read the article

  • How can I selectively increase latency? E.g. throttle games

    - by Arcymag
    Basically, I want networked games to run poorly on a network, but I want everything else to run smoothly. I would also appreciate advice on blocking games in general. As far as I can tell, there's a few ways to completely prevent an internet game from running: Blocking entirely via DNS configuration (e.g. hosts file), or router DNS configuration Blocking entirely via a separate DNS server Blocking the application, by uninstalling or some kind of access control Blocking the application by automatically killing the process every once in a while Blocking the application by corrupting files periodically However, I would like a more subtle way to block a program. Something that either: Increases latency (would this be doable through some kind of QoS like what DD-WRT offers?) Increases latency by using a special routing configuration for specific target IPs Throttle other systems resources, such as memory, IO, or CPU Screw around with keyboard configurations when a game is launched I would like this to work on MacOSX and Windows, but Linux would be great too. FYI I don't have a kid, but I was brainstorming with some friends and parents.

    Read the article

  • Cannot ping ubuntu server by hostname - can only ping by IP

    - by Tone
    I have an unbuntu 9.10 server and have set the hostname to "fileserver" When I try to ping fileserver from a client machine it doesn't find it, however I can ping by the IP my router assigns it. I have tried changing the ip in /etc/hosts from this: 127.0.0.1 fileserver to this: 192.168.1.109 fileserver which is the ip being assigned. I had a previous install of this server and i had no issues with this - only difference in this install is i did not select any of the options such as LAMP, OpenSSH, etc during the install process. I can access the machine fine by ip using PuTTY. Any ideas?

    Read the article

  • Static Routes and the Routing Table

    - by TheD
    This is very much a learning question if someone would be happy to explain a couple of concepts. My question is - the default routing table that exists in, in my case, a default Windows 7 install, what do each of the routes in the table do? Here is a screenshot: The 10.128.4.0 is just a route I've added while messing. I understand from a question I posted on Superuser the first route is just a default route that will route all traffic for any IP to my default gateway on my Interface in use. But what about the others? And how would the routing table handle a machine with multiple NIC's, perhaps connected to two different networks, or maybe even two NIC's on the same network so a VM can have a physical Network card instead of each VM sharing the hosts. Thanks!

    Read the article

  • Why is .htaccess not allowed in a directory but is allowed in another?

    - by JD Isaacks
    I have apache2 installed on ubuntu 10.4 inside my var/www/ directory [amung others] I have a cakephp and a dvdcatalog directories. Each of which have CakePHP 1.3 installed. I can access them both via localhost/cakephp and localhost/dvdcatalog But the dvdcatalog shows up with no css styling. They both have these files: /var/www/cakephp/app/webroot/css/cake.generic.css /var/www/dvdcatalog/app/webroot/css/cake.generic.css But when I go to http://localhost/cakephp/css/cake.generic.css it sees the file but it does not see the file when I go to http://localhost/dvdcatalog/css/cake.generic.css I think this means the cakephp folder is able to use .htaccess and the dvdcatalog is not. I setup the cakephp directory last month when I was following in the blog tutorial. I am setting up the dvdcatalog directory now for a different tutorial. So I am not sure if I am missing a step. in my /etc/apache2/apache2.conf file I have this: <Directory "/var/www/*"> Order allow,deny Allow from all AllowOverride All </Directory> Which I thought gave .htaccesss to all. Does anyone have any ideas what the problem is?

    Read the article

  • Spamassassin: How to delete all spam messages on the server?

    - by Beck
    Can't find out, how to configure spamassassin to delete all spam messages. Currenly it's only mark messages as spam, but pass them throught IMAP to client. How to block them from passing through to IMAP clients? http://spamassassin.apache.org/full/3.3.x/doc/Mail_SpamAssassin_Conf.html And it's blocking some of our notification messages... -1.4 ALL_TRUSTED Passed through trusted hosts only via SMTP 0.0 HTML_MESSAGE BODY: HTML included in message 2.4 HTML_IMAGE_ONLY_08 BODY: HTML: images with 400-800 bytes of words 2.9 TVD_SPACE_RATIO BODY: TVD_SPACE_RATIO 1.7 MIME_HTML_ONLY BODY: Message only has text/html MIME parts 1.1 HTML_MIME_NO_HTML_TAG HTML-only message, but there is no HTML tag 1.1 HTML_SHORT_LINK_IMG_1 HTML is very short with a linked image -1.4 AWL AWL: From: address is in the auto white-list This is what clients getting on their mails in place of our notification messages. Any idea how to pass those messages through and how to delete incoming spam? Thanks ;) I have this setup: postfix spamassassin clamav-daemon amavis

    Read the article

  • How do you enable syslogd to accept incoming connections on Snow Leopard from remote loggers?

    - by Emmel
    How do I get syslogd to accept incoming connections from remote hosts on Snow Leopard? I'd like to centralize logging such that various devices and systems send logs to Snow Leopard's syslogd, which normally hangs out on UDP 514. However, I'm unable to get them to successfully be accepted by good ole syslogd. I tcpdumped on the Snow Leopard box to verify that packets are being spouted to port 514 -- they are. I checked that syslogd is listening on 514 -- it's not. Googling around told me that, on older versions of OSX (don't you love the way things change so rapidly on OSX), one just had to add a flag to the syslogd daemon to allow remote; one did this in com.apple.syslogd.plist. However the syslogd daemon has no flags (at least in its man page) that suggests any remote anything. What's the solution to this? Secondary, less import but relevant question: What's 'newsyslog'? I see a plist file but it's not running (apparently). Thanks

    Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >