Search Results

Search found 4786 results on 192 pages for 'traffic shaping'.

Page 164/192 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

• What's the best way to run Drupal and Django sites behind the same Varnish server?

  - by Alexis Bellido

  I have a high traffic website running with Drupal and Apache, five web servers behind a Varnish server load balancing. Let's say this site is example.com. I'm using five backends and a director like this in my default.vcl: director balancer round-robin { { .backend = web1; } { .backend = web2; } { .backend = web3; } { .backend = web4; } { .backend = web5; } } Now I'm working on a new Django project that will be a new section of this site running on example.com/new-section. After checking the documentation I found I can do something like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.backend = newbackend; } else { set req.backend = default; } } That is, using a different backend for a subdirectory /new-section under the same domain. My question is, how do I make something like this work with my director and load balancing setup? I'm probably going to run two or more web servers (backends) with my new Django project, each one with a mix of Gunicorn, Nginx, and a few Python packages, and would like to put all of those in their own Varnish director to load balance. Is it possible to do use the above approach to decide which director to use?, like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.director = newdirector; } else { set req.director = balancer; } } All suggestions welcome. Thanks!

  Read the article

• Unable to PPTP through NAT on Cisco 881

  - by MasterRoot24

  I'm trying to connect to a PPTP server which is sat behind a Cisco 881 NAT router. The server is running Ubuntu Server 12.04 and is running Poptop pptpd as the PPTP daemon listening for connections. As discussed in my other question, I'm trying to setup a Cisco 881 router to replace my old Linksys WAG320N. This same server and WAN connection worked fine with the WAG320N with no special configuration, other than allowing 1723 in through the firewall. On the Cisco 881, I'm using the newer ip nat enable or NAT NVI to setup static routes in through the firewall for the services running behind the router. My reason being that I can't run another copy of my live DNS domains internally with local IP addresses in. For the purposes of this question, though, I have rebuilt the router with ip nat inside/outside style NAT'ing, but this issue is still apparent. HTTP/SMTP/IMAP etc. all work ok from both the WAN and LAN interfaces of the router. I'm only having issues with SIP (see other question) and PPTP. My issue is that the GRE doesn't appear to be passing through NAT correctly and one end of the connection is not receiving GRE traffic when it should be, so the server hangs up the connection. Here's an example of /var/log/syslog with debug enabled in /etc/pptpd.conf: Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: MGR: Launching /usr/sbin/pptpctrl to handle client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pppd options file = /etc/ppp/pptpd-options Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection started Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 1) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a START CTRL CONN RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 156 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 7) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Set parameters to 100000000 maxbps, 64 window size Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a OUT CALL RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Starting call (launching pppd, opening GRE) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pty_fd = 6 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: tty_fd = 7 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 32 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): program binary = /usr/sbin/pppd Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Dec 11 21:06:30 <HOSTNAME> pppd[22627]: pppd 2.4.5 started by root, uid 0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Using interface ppp0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Connect: ppp0 <--> /dev/pts/3 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: GRE: Bad checksum from pppd. Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 15) Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Got a SET LINK INFO packet with standard ACCMs Dec 11 21:07:00 <HOSTNAME> pppd[22627]: LCP: timeout sending Config-Requests Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Connection terminated. Dec 11 21:07:00 <HOSTNAME> avahi-daemon[1042]: Withdrawing workstation service for ppp0. Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Modem hangup Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Exit. Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Reaping child PPP[22627] Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection finished Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Exiting now Dec 11 21:07:00 <HOSTNAME> pptpd[5803]: MGR: Reaped child 22626 As far as Cisco are concerned, all I need is ip nat source static tcp <SERVER LAN IP> 1723 interface FastEthernet4 1723 but of course this doesn't seem to the be helping the GRE traffic through as it should. Trying the connection to the LAN IP of the server from the same LAN as the server (behind the router), the PPTP connection works fine, so I'm confident that the server's config is ok. Furthermore, all I needed on my WAG320N was to open 1723 in the firewall. Here's my current router config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end UPDATE 16/12/2012: The only progress that I have been able to make on this issue is that I'm confident that the issue is caused by the GRE tunnels (which are required for the PPTP connection to complete) are being blocked. When attempting a connection, I can see in show ip nat nvi translations that both a TCP translation on 1723 is setup and also a GRE translation is setup also. I appear to be able to see GRE related packets on the LAN that the server is on, so I am lead to believe that the server is sending(?) GRE packets, however running Wireshark on a client PC when attempting a connection shows absolutely no GRE packets. Whilst there are no configuration directives in my config posted above (that I can pin point) which would specifically block them, it would appear that the GRE packets are not being allowed in/out of the router's firewall, even though a NAT translation entry is setup to the server's LAN address. Would anyone be able to provide me with some help to ensure that GRE packets are not blocked by the router's firewall, so that this can be ruled out as a possible issue please?

  Read the article

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• How to best tune my SAN/Initiators for best performance?

  - by Disco

  Recent owner of a Dell PowerVault MD3600i i'm experiencing some weird results. I have a dedicated 24x 10GbE Switch (PowerConnect 8024), setup to jumbo frames 9K. The MD3600 has 2 RAID controllers, each has 2x 10GbE ethernet nics. There's nothing else on the switch; one VLAN for SAN traffic. Here's my multipath.conf defaults { udev_dir /dev polling_interval 5 selector "round-robin 0" path_grouping_policy multibus getuid_callout "/sbin/scsi_id -g -u -s /block/%n" prio_callout none path_checker readsector0 rr_min_io 100 max_fds 8192 rr_weight priorities failback immediate no_path_retry fail user_friendly_names yes # prio rdac } blacklist { device { vendor "*" product "Universal Xport" } # devnode "^sd[a-z]" } devices { device { vendor "DELL" product "MD36xxi" path_grouping_policy group_by_prio prio rdac # polling_interval 5 path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And iscsid.conf : node.startup = automatic node.session.timeo.replacement_timeout = 15 node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 10 node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 After my tests; i can barely come to 200 Mb/s read/write. Should I expect more than that ? Providing it has dual 10 GbE my thoughts where to come around the 400 Mb/s. Any ideas ? Guidelines ? Troubleshooting tips ?

  Read the article

• No apparent reason for high load average

  - by Oz.

  We have several web servers running on Amazon (ec2) c1.xlarge, over Amazon AMI. The servers are duplicates of each other, running the exact same hardware and software. Each server spec is: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge A couple of weeks ago we have run a yum upgrade on one of the servers. Starting on this upgrade the upgraded server started showing a high load average. Needless to say, we did not update the other servers and we can not do so until we understand the reason for this behavior. The strange thing is that when we compare the servers using top or iostat, we can not find the reason for the high load. Note that we have moved traffic from the "problematic" server to the others, which have made the "problematic" server less crowded in terms of requests, and still his load is higher. Do you have any idea what could it be, or where else can we check? Many thanks for the help! Oz. # # proper server # w command # 00:42:26 up 2 days, 19:54, 2 users, load average: 0.41, 0.48, 0.49 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/1 82.80.137.29 00:28 14:05 0.01s 0.01s -bash pts/2 82.80.137.29 00:38 0.00s 0.02s 0.00s w # # proper server # iostat command # Linux 3.2.12-3.2.4.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 9.03 0.02 4.26 0.17 0.13 86.39 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.63 1.50 55.00 367236 13444008 xvdfp1 4.41 45.93 70.48 11227226 17228552 xvdfp2 2.61 2.01 59.81 491890 14620104 xvdfp3 8.16 14.47 94.23 3536522 23034376 xvdfp4 0.98 0.79 45.86 192818 11209784 # # problematic server # w command # 00:43:26 up 2 days, 21:52, 2 users, load average: 1.35, 1.10, 1.17 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/0 82.80.137.29 00:28 15:04 0.02s 0.02s -bash pts/1 82.80.137.29 00:38 0.00s 0.05s 0.00s w # # problematic server # iostat command # Linux 3.2.20-1.29.6.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 7.97 0.04 3.43 0.19 0.07 88.30 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.10 1.49 76.54 374660 19253592 xvdfp1 5.64 40.98 85.92 10308946 21612112 xvdfp2 3.97 4.32 93.18 1087090 23439488 xvdfp3 10.87 30.30 115.14 7622474 28961720 xvdfp4 1.12 0.28 65.54 71034 16487112

  Read the article

• Is it possible to change "working directory" of XeTeX?

  - by Herbert Sitz

  Using XeTeX there are many working files that get created in process of producing the pdf, and they litter the directory where my main .tex file is. Is it possible to change the working directory of XeTeX so that it stores all these scratch files in some other directory, out of the way? There is a previous question on Superuser.com that discusses a utility that cleans up the working files by deleting them after they're produced: http://superuser.com/questions/95712/how-to-avoid-littering-ones-tex-directories-with-intermediate-files That solution doesn't work for me since I'm using XeTeX, but also it seems like it would be preferable to simply be able to designate a "scratch" directory where all working files are saved. I haven't been able to find any info on how to do it though. Is there a way? (My question is prompted partly because of the fact that I often work with files in a directory that is shared using DropBox, so it creates a lot of unnecessary traffic if files are getting created and destroyed willy nilly. I don't know if it affects speed in any way, but the idea of having a separate working directory that is not shared/replicated by DropBox would be a cleaner solution, even if I could use the method suggested in the earlier thread.)

  Read the article

• How to configure a trusted connection between IIS 7 and SQL Server 2005?

  - by user1180652

  How do configure a trusted connection between IIS 7 and SQL Server 2005? My webapp was working fine with Windows Authentication enabled in IIS. Now, in order to solve a problem, we need to use a trusted connection. Unfortunately, enabling the trusted connection in the web.config broke the webapp. Oddly enough, when I run this application with trusted connection from my local dev machine (using the Cassini web server) IIS (Windows Server 2008) is running on one machine. The database (SQL Server 2005 but could migrate to 2008) is running on another machine. We are on a Windows domain running AD. All traffic is within our own firewall - no public access. Beyond that, I can't provide much info but I can find it. We're very "compartmentalized" (we have server people, security people, oracle people, SQL Server people, etc.) Thanks! Update 02/14/2012 0902: The webapp is now functional (app no longer broken) but the main issue is still unresolved. Now I have the app's application pool running as a domain account with permissions on the SQL Server box and IIS box. We were using this account to run the application but, and here's the problem, we need to log the real user name that made a change. When using the service account, the name of that service account appeared in the audit tables, making the auditing quite useless. So, not I'm at least running again. The connection string in the web.config is using "Trusted_Connection=True", the appPool is using a domain account with access to both boxes, BUT when I make a change (logged in as me) the name of the service account (appPool identity) is still logged in the audit tables. I also manually granted full permissions to the service account on the webapp folder. What do I need to do in order to log my name, not the service account, in the audit tables? Everything I'm reading says I need to establish a trusted connection between the two servers.

  Read the article

• Enabling NAT forwarding using a second WAN interface and a second gateway on ubuntu

  - by nixnotwin

  I have 3 interfaces: eth0 192.168.0.50/24 eth1 10.0.0.200/24 eth2 225.228.123.211 The default gateway is 192.168.0.1 which I want to keep as it is in the changes I want to make. I want to masquerade eth1 10.0.0.200/24 and enable NAT forwarding to eth2. So I have done this: ip route add 225.228.123.208/29 dev eth2 src 225.228.123.211 table t1 ip route add default via 225.228.123.209 dev eth2 table t1 ip rule add from 225.228.123.211 table t1 ip rule add to 225.228.123.211 table t1 Now I can receive ping replies from any internet host if I did: ping -I eth2 8.8.8.8 To enable NAT forwarding I did this: sudo iptables -A FORWARD -o eth2 -i eth1 -s 10.0.0.0/24 -m conntrack --ctstate NEW -j ACCEPT sudo iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT sudo iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE But it isn't working. To test I used a client pc and put it on 10.0.0.0/24 network and gateway was set as 10.0.0.200. I want to have 192.168.0.1 as default gateway. And the traffic that comes in via eth1 10.0.0.200/24 should be forwarded to eth2 225.228.123.211. I have enabled forwarding on ubuntua also.

  Read the article

• Network access lags for Win7 when server network utilization is high

  - by Jeff Miles

  We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

  Read the article

• High CPU usage in my digitalocean droplet

  - by Ibrahim Azhar Armar

  I am experiencing high CPU usage here is the stats i got from server, the consumption after every restart in 15 minutes go upto 100%, what could go wrong? I have a wordpress copy installed on the server which does not have much traffic, here is the stats that i got from using top command in server. top - 11:46:02 up 12 min, 3 users, load average: 40.89, 16.03, 6.11 Tasks: 132 total, 41 running, 91 sleeping, 0 stopped, 0 zombie Cpu(s): 24.3%us, 61.5%sy, 0.0%ni, 0.0%id, 4.0%wa, 0.0%hi, 0.0%si, 10.2%st Mem: 2050896k total, 1988656k used, 62240k free, 284k buffers Swap: 0k total, 0k used, 0k free, 4712k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31 root 20 0 0 0 0 R 39 0.0 1:35.53 kswapd0 899 root 20 0 15988 172 0 S 14 0.0 0:05.00 irqbalance 418 syslog 20 0 243m 600 0 S 13 0.0 0:06.85 rsyslogd 944 mysql 20 0 1320m 53m 0 S 12 2.7 0:21.15 mysqld 2357 root 20 0 17344 532 164 R 11 0.0 0:14.27 top 960 root 20 0 246m 3816 0 S 3 0.2 0:08.18 php5-fpm 2431 www-data 20 0 344m 64m 908 R 2 3.2 0:04.23 apache2 2435 www-data 20 0 304m 63m 836 R 2 3.2 0:03.43 apache2 2413 www-data 20 0 349m 63m 920 R 2 3.2 0:07.51 apache2 2465 www-data 20 0 349m 64m 944 R 2 3.2 0:05.04 apache2 2518 www-data 20 0 307m 41m 1204 R 2 2.1 0:01.37 apache2 2406 www-data 20 0 346m 56m 1144 R 2 2.8 0:03.76 apache2 2456 www-data 20 0 345m 55m 1184 R 2 2.8 0:02.67 apache2 2373 www-data 20 0 351m 63m 784 R 2 3.2 0:11.09 apache2 2439 www-data 20 0 306m 35m 916 R 2 1.8 0:02.51 apache2 2450 www-data 20 0 345m 55m 1088 R 2 2.8 0:02.96 apache2 2486 www-data 20 0 299m 10m 876 R 2 0.5 0:01.19 apache2 2523 www-data 20 0 300m 27m 796 R 2 1.4 0:00.99 apache2

  Read the article

• How to publish internal data to the internet - as simple as possible

  - by mlarsen

  I Asked this at Staock Overflow, but I would like your oppinion too as it has as much to do with administration as it does with coding. We have a .net 2-tier application where a desktop program is talking to a database. We support MS SQL Server 2000, 2005, 2008 and Oracle 9, 10 and 11. The application is sold, not as shrink-wrap, but pretty close. It is quite important for us that the installation and configuration is as easy as possible as installation instructions are usually supplied in written form to the customers internal IT-department. Our application is usually not seen as mission critical for the IT-department, so we need to keep their work down to a minimum. Now we are starting to get wishes for a web application build on top of the same data. The web application will be hosted by us and delivered as a SaaS application. Now the challenge is how to move data back and forth between the web application and the customers internal database. as I see it we have some requirements: We must be ready to handle the situation where the customers database is not accessible from the DMZ. I guess the easiest solution is that all communication is initiated from inside the customers lan. As little firewall configuration as possible. The best is if we can run without any special configuration as long as outgoing traffic from the customers lan are not blocked. If we need something changed in the firewall, we must be able to document that the change is secure. It doesn't have to be real time. Moving data in batches every ten minutes or so is OK. Data moves both ways, but not the same tables, so we don't have to support merges. It would be nice if we don't have to roll our own framework completely. Looking forward to hear your suggestions.

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Recommendation for robust, customizable, open source, Java servlet-based forum software?

  - by Erik Hermansen

  There is a lot of forum software out there, but it seems to me that a lot of the popular choices are PHP-based. And for my project, I'd like something based on Java servlets so my team can make customizations to it. Another important feature is that I can completely change the pages to hide unwanted elements without too much work. So I'm looking either for a template system or easily editable scripts (i.e. JSPs) that have a clean view separation. Just having skin changes or CSS customization is not enough. I understand that if I have open source, I can change anything I want, but my point is that it should be easy and not requiring mastery of a complex code base. Finally, I want something that has been around for at least a year and deployed on some high-traffic sites. Clustering support (one database, multiple web servers) is highly desirable. Up-time is crucial since I have an SLA to support. What do you think?

  Read the article

• What program sent which packet to the network [closed]

  - by Erik Johansson

  I would like to have a tcpdump like program that shows which program sent a specific packet, instead of just getting the port number. This is a generic problem I've had on and off sometimes when you have and old tcpdump file lying around you have no way to find what program was sending that data.. The solution in how i can identify which process is making UDP traffic on linux ? is an indication that I can solve this with auditd, dTrace, OProfile or SystemTap, but doesn't show how to do it. I.e. it doesn't show the source port of the program calling bind().. The problem I had was strange UDP packets, and since those ports are so short lived it took me a while to solve this issue. I solved this by running an ugly hack similar to: while true; date +%s.%N;netstat -panut;done So either a method better than this hack, a replacement for tcpdump, or some way to get this info from the kernel so I can patch tcpdump. EDIT: This was asked on superuser "tracking what programs sends to net", no good solution though.

  Read the article

• IPtables: DNAT not working

  - by GetFree

  In a CentOS server I have, I want to forward port 8080 to a third-party webserver. So I added this rule: iptables -t nat -A PREROUTING -p tcp --dport 8080 -j DNAT --to-destination thirdparty_server_ip:80 But it doesn't seem to work. In an effort to debug the process, I added these two LOG rules: iptables -t mangle -A PREROUTING -p tcp --src my_laptop_ip --dport ! 22 -j LOG --log-level warning --log-prefix "[_REQUEST_COMING_FROM_CLIENT_] " iptables -t nat -A POSTROUTING -p tcp --dst thirdparty_server_ip -j LOG --log-level warning --log-prefix "[_REQUEST_BEING_FORWARDED_] " (the --dport ! 22 part is there just to filter out the SSH traffic so that my log file doesn't get flooded) According to this page the mangle/PREROUTING chain is the first one to process incomming packets and the nat/POSTROUTING chain is the last one to process outgoing packets. And since the nat/PREROUTING chain comes in the middle of the other two, the three rules should do this: the rule in mangle/PREROUTING logs the incomming packets the rule in nat/PREROUTING modifies the packets (it changes the dest IP and port) the rule in nat/POSTROUTING logs the modified packets about to be forwarded Although the first rule does log incomming packets comming from my laptop, the third rule doesn't log the packets which are supposed to be modified by the second rule. It does log, however, packets that are produced in the server, hence I know the two LOG rules are working properly. Why are the packets not being forwarded, or at least why are they not being logged by the third rule? PS: there are no more rules than those three. All other chains in all tables are empty and with policy ACCEPT.

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• How to use Cisco AnyConnect VPN Client?

  - by ktm5124

  I wrote a related question earlier, which is still unresolved. This question is much more specific. So I installed Cisco AnyConnect VPN Client on Snow Leopard. I connect to my work VPN. Once connected, I can't ping my work machine. I don't see any computers on the network. If the client were not running, I wouldn't believe myself to be connected to the VPN. Is there something that I am doing wrong? Do I have to route my network traffic through the tunnel manually? (ifconfig route comes to mind) Is the POST request that I am about to submit going to go through the tunnel created by my VPN? I guess the main question is: why do I feel so in the dark? Cisco says I am connected to my VPN, but for all I know it is invisible. N.B. I do have the up-to-date Cisco VPN Client: version 2.3.2016. I installed it about a week ago.

  Read the article

• How should I perform database maintenance on a 24x7 system

  - by solublefish

  I'm a software developer who inherited a part-time DBA role. I'm responsible for an application backed by a small, high-volume 24x7 database on SQL Server 2008. While there's other stuff in the DB, the critical piece is a 50GB, 7.5M row table that serves 100K requests/sec during peak load, and about half that at "night". This is 99%+ read traffic, but the writes are constant, and required. I need to be able to perform periodic maintenance without a maintenance window. Say an index rebuild, a job to purge old data, Windows Update, or hardware upgrade. Most of the advice I've seen is along the lines of "MAKE a maintenance window." While I appreciate the sentiment, I hope there's another way. If it will solve this problem, I do have the ability to purchase new hardware or modify the database, the clients (a set of web services servers), and much of the application code (ADO.NET + ASP.NET). I've been thinking along the lines of using the warm spare (or a 3rd server) to do the maintenance, and then "swap" it into production. 1 Synchronize the spare by restoring backups, including a current transaction log. 2 Perform the maintenance tasks. 3 Reconfigure clients to connect to the spare server. Existing connections are finished within a minute or so. 4 The spare server is now the production server. The problem remaining is that the new production server is now out of date by however long it took to perform maintenance. Is there some way that the original production server can be made to queue up changes and merge them to the spare between steps 2 and 3? Any other ideas?

  Read the article

• MSSQL Timing out, a couple of questions...

  - by user29000

  Hi, About once a week, my MSSQL server is timing out, or rather the machine runs out of RAM. This morning it reached 3.9GB of the available 4, with MSSQL taking up 2.5GB. I'm concerned that i've not configured SQL to release memory as it should, so I ran sp_who2 while the timeouts were occuring to see what process were running. If i could post the CSV datafile i would, however, there were 85 processes in total, mostly related to the Full Text service: FT Gatherer - About 35 of these running under the 'sa' account against the master database with status of either sleeping or background, many were dependant on other processes. Is that normal? MySite database - There were only 5 processes for the one active site/database and all were either sleeping or suspended - but their lastBatch dates were set to 1/12/2020. Is that normal? The datbase is only about 20mb in size the traffic levels are very low, so i'm thinking of maybe limiting the amount of RAM SQL has access to (from unlimted to maybe 2GB). Any thoughts / advise would be appreciated. Mny thanks Ben

  Read the article

• EMC VNX iSCSI setup - unsure about SP/port assignment

  - by pauska

  We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >