Search Results

Search found 4813 results on 193 pages for 'ram shankar yadav'.

Page 167/193 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• Max. Temp. on Intel Burn Test for Stock Dell Precision T3500

  - by HK1

  I'm troubleshooting an issue on a Dell Precision T3500. As part of my troubleshooting I've decided to try running a stress test using Intel Burn Test software. This machine is a stock configuration with 12GB of RAM and a Xeon W3670 processor (nothing overclocked). When I run IBT using the standard mode, SpeedFan reports a processor temperature in excess of 80C. I've seen numbers as high as 90C but even at that temperature the machine does not become unstable or crash. However, it seems way too high. This processor has a TCase of 67.9C according to Intel's website. I'm guessing that means I'm in the danger zone any time I go over that temperature. I've checked the cooling system and everything looks fine. I've even took out the heat sink and reinstalled it with new thermal compound. This did not appear to make the problem better or worse. Is there a discrepancy somewhere here in the way temperatures are measured or displayed? I've also tried using HWMonitor from CPUID and it reports the same temperatures. Should I just let the Standard Test go and disregard the temperature outputs?

  Read the article

• Capabilities of business and SOHO routers

  - by Q8Y

  I'm currently studying for the CCNA certifications (especially for Cisco routers and configuration). I know that business routers provide more features than SOHO routers, the processing speed and RAM can be enough. Assume I need to connect a number of users through a network (accessing internet, share files, printers, ...). I have a high speed connection to the internet and I already applied QoS. How can I find out how many users such a single (SOHO) router could handle? In my case I'd attach to it multiple switches until I have the number of ports needed. Would everything work well and smoothly with 50 users? What about 300? At which point would I need a business router instead? If I implemented VLAN here, would it make any difference in the performance? When do I really need to use more than one router? (Both SOHO and business) I'm thinking that I may need them only if I want to increase the performance (instead of replacing the existing one) and if I have multiple locations, so in this situation I need to have multiple routers, right? Put differently: Is there is a need to have another router if my business all in one place?

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Is there an application to log component temperatures to file?

  - by MrVimes

  I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

  Read the article

• Diagnose remote desktop freezes in Windows 7 when no BSOD?

  - by Paul Smith

  Okay, I'm getting no joy from Asus or Microsoft on this, so hoping for some clues on how to narrow down the cause. I have very frequent OS freezes, always & only when running Remote Destkop Client (mstsc) in Windows 7 x64. I never have a bluescreen, and there is never a minidump. The display & input just freezes -- no keyboard, no mouse, and sound will just continue the last wavelength if any. So far, I can't find a way to trap the hang given that there's no bluescreen; advanced startup & recovery settings for system failure are "Write an event" checked, "Automatically restart" checked, and "Kernel memory dump". I've updated to the lasted BIOS, and tried a few different graphics drivers, both generic & ATI. I've also tried disabling Aero, and everything about the remote desktop experience (incrementally unchecked every box in the mstsc - options - experience tab), even disabled/unplugged external monitor to make sure it wasn't a dual-monitor issue. My specs are: Asus G73jh notebook 8GB RAM ATI Mobility Radeon HD 5800 Series graphics (recently tried driver versions 8.791.0.0, 8.801.0.0) American Megatrends G73jh.211 BIOS (7/27/2010) Windows 7 Home Premium x64 Windows Memory Diagnostic passed all of the following at least 3 times with no errors: MATS+ INVC LRAND Stride6 WMATS+ WINVC This notebook is better than most at removing heat (laudable vent design), so I'm not inclined to suspect thermal causes (especially since running 1080p video for hours has never caused a freeze, but mstsc does, reliably, within 5 minutes to an hour). This did seem to start happening after a Windows Update, but I've since reverted every patch applied since a week before the first occurrence, with no joy. (And I'd only had the PC for a couple weeks before that, so it could have been chance + less actual time spent remoting at the beginning.) I'm at my wits end, and I bought this laptop primarily as a remote terminal client (go figure, right?) Any ideas on how to identify the cause of this? Thanks!

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Display issue with fresh install of windows server 2012

  - by Tony

  I installed windows server 2012 last night on my home "server". I use server loosely. From the get go I had display and graphic issues. The image was fuzzy and jumbled up during the install. This continued once booted into the install. I did installed Server 2012 twice now as the first time, I only installed "core". I know this is not a busted graphics card because it worked fine in Win7, during boot, and fine in "core" mode. Once booted into "GUI" install of Server 2012, the image was messed up again. To make things even more weird, the windows "loading" screen looks fine. Once the login screen appears the image is fuzzy and jumbled. My guess was that it was a driver issue. I did try to install the win8 x64 drivers from nvidia. This caused the system to become unbootable and I had to restore to a previous working point and uninstall the driver. I did try two different monitors and cables. Also both ports on the back of the video card. I did manage to get RDP running and that works fine. I rarely work directly on this machine but it would be nice to have the option back. Geforce 210, AMD 4600+, 4 gigs of ram.

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

  - by Gleeson9

  Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

  Read the article

• I cannot connect to home server after a few hours

  - by Iago

  I have an old PC and I decided to revive it. A LAMP (for my own use) and a P2P server (torrent and e2dk). My old PC is an AMD Athlon XP (1400 MHz) with 384 Mb of RAM First of all I installed Ubuntu Server 11.10, SSH, FTP, SAMBA and LAMP. With this configuration my home server works well, with no problem. Then I went to the P2P server and I tried rTorrent and then uTorrent Server Alpha. And here is my problem. After a few hours (maybe 10 hours, or maybe 30 hours) with the torrent app running (rTorrent or uTorrent) I lose the connection to my home server. That is, I cannot access via ssh, I cannot access the apache server, etc. but I can ping the home server. It seems that the server freezes and all I can do is reboot the server physically. So, I have two questions: What is the problem? and How can I solve it?

  Read the article

• I think my laptop just died

  - by Joel Coehoorn

  I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Windows 7 Paging file apparently not being used

  - by Daniel F.

  I'm running Windows 7 Home Premium 32bit on a mobo with 24GB RAM. Of those 24GB, 20GB are assigned as a RAMDISK via ASRock XFastRAM. This RAMDISK has the drive letter X assigned to it. On X:\ I'm storing the temporary files folder, as well as pagefile.sys. Pagefile.sys has 6GB of size. The X:\ has usually around 14GB free space, so the temporary files are negligible, it's mostly the browsers which are storing their caches on there. Now my issue is that Firefox is crashing a lot on me, no error message pops up, but I know that this is because it's out of memory. I could kind of live with that, but now that I switched from using Eclipse to Android Studio, I know that I'm in trouble, because Java isn't capable of allocating, and Android Studio, together with the Java instances it launches, is quite a memory hog. So I tried to figure out what's wrong, and apparently Windows isn't swapping out memory onto the paging file. While my applications are crashing (firefox) / not starting (java vm's), the paging file is only using constantly around 15% of its size (checked with the performance monitor). 15% equals to 1GB aprox. I know that the correct solution would be to switch to 64 bit Windows, but I had to use the 32 bit version because of driver issues which I had about two years ago, and I guess that I'll have them again if I reformat and install the 64 bit version. Also, the machine is running quite stable, the only issue is the memory, so I'd like to use it as it is (as the apps are installed and configured) Is there a way to make Windows use the paging file more efficiently? None of my processes require more than 1GB, I'd just like it to swap out some seldomly used stuff, like GoogleCrashHandler.exe and stuff like that in order to have "more physical memory avaliable". Is that possible?

  Read the article

• Software raid 0 with six disks performance

  - by user134880

  I have some problems with disk performance. I have 6 x WD 500Gb RE4 disks. Each disk gives 135Mb/sec throughput. All measurements are made with hdparm with options "-tT" (I know that it is just synthetic test, but I need some start point to make measurements). I have controller with Sil3124 x 4 ports PCI Express 1x So... RAID0 on controller with 2 disks gives 200Mb/s - ok, pcie limit. RAID0 on motherboard with 2 disks gives 270Mb/s - niceeee :) RAID0 on contorller with 4 disks gives 200Mb/s - ok, pcie limit. RAID0 on controller with 4 disks + 1 disks on motherboard = 340Mb/s ... :( RAID0 on controller with 4 disks + 2 disks on motherboard = 300Mb/s .... why? Any ideas? Maybe need more cpu power? Now there is Pentium D Dual core 2.8Ghz, 4Gb RAM. It is dedicated box for storage.. no other activity.

  Read the article

• A very peculiar problem with an old pc and a newer laptop...

  - by user553492

  I got my old pc ( 248mb ram , 80 GB ) repaired and the tech people put XP in it .My newer laptop has UBUNTU 10.04 .now I only have one cable and one usb cord .So I connected my modem (with only one CAT5 port and 4 usb ports ) to laptop with CAT5 cable .Th internet is working fine . I also wanted to use net on older pc so I installed the usb drivers for win and it worked. But I got fed up of win xp and made a separate partition for FreeBSD which I planned to install .During the install I screwd up sumthing and now freebsd starts with a boot option with a ? mark in place of win xp .If I click on that it gives me a "NTLDR missing " msg. I tried connecting CAT5 cable between old and new pc and tried connecting my laptop with USB cable but nothing happend and then I realozed the modem doesnt have a WORKING usb driver for LINUX :( .FCUK ! .Freebsd doesnt` even detect the LAN cable if I use it for old pc . So basically I have a old pc that has FREEBSD which I can olny start and stare at the blank terminal console but works perfectly otherwise .FREEBSD was supposed to detect the LAN cable ??.And I have a laptop that has LINUX which only works if I connect it with a CAT5 cable .wtf . So what can I do with my old pc ??? any local server (if possible :( ) or some such thing ? or can u suggest any use .Im 18 and im into learning programming , coding .So I can practice it .Thankx !

  Read the article

• Some Apps don't start on Windows 8 Release Preview

  - by Exa

  I recently installed the Release Preview of Windows 8 in a virtual machine. Some apps do not work. When I open them (by clicking on their tile in the start screen) I see a splash screen and nothing else happens. Sometimes the app crashes after 30 seconds, sometimes it just keeps on loading. A good example is the "Map"-App from Windows 8 or the app "Cookbook" by Bewise. I installed Cookbook and when I had a look at the task manager I saw that it was the 32bit version running, but I have an x64 Windows 8... Could this be a problem? Shouldn't the Windows Store download the correct version? This is the setup of my virtual machine: Windows 8 Release Preview x64 Oracle VirtualBox 4 of 8 cores from host system 8 of 16 GB RAM from the host system 256 MB graphics memory guest additions installed resolution 1920 x 1080 Do you need further information? Unfortunately there is no error message... I just see the start screen of the app with its logo and it keeps loading, but nothing happens. Other Apps (like Mail, Video, Social, etc.) work fine.

  Read the article

• RAID 6 that can read with least 1000 Mbit/s?

  - by Diblo Dk

  I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

  Read the article

• Php5-fpm Crash if much visitors

  - by chillah

  I decided to change my OP to Nginx from Litespeed because i read much about the low resource that Nginx would cost. Im running a Wordpress site with 500 users online My www.conf in "/etc/php5/fpm/pool.d" pm.max_children = 200 pm.start_servers = 20 pm.min_spare_servers = 20 pm.max_spare_servers = 60 ;pm.process_idle_timeout = 10s; ;pm.max_requests = 1000 Since i changed that config to higher requests and more children the Site needs longer till it shows me a White blank page. If i restart the php5-fpm prozess then, the site is running fine again. The CPU usage is at 5% if the php5-fpm is crashed and if its running its about 20 to 90%! Heres my Nginx.conf: user www-data; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 3048; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; I already tried changing the settings, tryed all variants but nothing worked. The Mashine: Dualcore 4gb ram

  Read the article

• Troubles Installing Windows 7 via USB. Flat install?

  - by Brian

  Hi friends, I've been struggling with this for a while. Windows 7 64-bit Enterprise edition just will not install on my Shuttle K45 system via a USB key. It hangs out during the install while copying files or while creating the partitions. The system is pretty standard and low-tech: IDE hard drives, no CD, 2G RAM. I am not sure what of the problem. Other than the Shuttle, I have a Apple MacBook Pro. On the MPB, I am running OS X, and Mint Linux and Window XP over Parallels. I have an ISO of Win7 that works (I installed it as a Parallels VM to make sure). I have used UltraISO and MS Windows 7 USB/DVD Download Tool to write it to the 8G USB key. Both seem to copy all the files correctly (with UltraISO, I asked it to verify). It boots via USB and the install looks just fine. Until it hangs, most of the time with a copying error of 0x80070241. So now I am trying to figure out if there are other ways I can install Windows 7 on this Shuttle system that has no CD drive. I've heard about a flat installation, however those all seem to be doing something from within Windows. I do have access to a command prompt from the Windows 7 install. Does anyone know if/how I can prep the Shuttle hard drive with Windows 7 installation and have Windows 7 install from the hard disk. I do not have an external enclosure for the IDE HD and I do not have any other system I can hook up to the hard drives. I do have an external Maxtor OneTouch drive available.

  Read the article

• What should the memory configuration be?

  - by AngryHacker

  We have a server (ProLiant DL585 G1 by HP), which hosts Windows 2003 x64 R2 with SQL Server 2005 x64 and a host of other apps. It currently has 6GB of RAM. We are currently very memory constrained and it's clear that we need to get more memory. 8GB will probably do the trick, however, we are not sure as to what memory configuration will give us the biggest performance buck. Currently all 8 memory slots are filled (4 slots have 1GB chip, while the other 4 slots have 512MB chips). Should we throw the 512MB sticks away and just replace them all with 1GB sticks? If we decided to go with a higher memory configuration (e.g. 10GB or 12GB or 16GB), is it advisable to keep all the sticks of the same size or it does not matter? I was once told that interleaved memory requires (for better performance) that memory should be in multiples (e.g. 2 or 4 or 8 or 16, etc...). I am not even sure that the server has an interleaved configuration (and don't know how to find out), but is this true? Thanks.

  Read the article

• Many different BSOD

  - by Exa

  I'm experiencing multiple bluescreens for a couple of months now. Their error code is as diverse as their time of occurence... Sometimes it happens during gaming, sometimes when watching videos, sometimes when the computer is idle. These are the bluescreens I see most often: PAGE_FAULT_IN_NONPAGED_AREA KMODE_EXCEPTION_NOT_HANDLED IRQL_NOT_LESS_OR_EQUAL SYSTEM_SERVICE_EXCEPTION SYSTEM_THREAD_EXCEPTION INTERRUPT_EXCEPTION_NOT_HANDLED DRIVER_IRQL_NOT_LESS_OR_EQUAL DRIVER_OVERRAN_STACK_BUFFER Responsible drivers (according to the memory dumps): hal.dll tcpip.sys dxgmms1.sys ndis.sys mouhid.sys atikmdag.sys dump_atapi.sys and of course: ntoskrnl.exe My first thought was a driver incompatibility because I am using Windows 8 and some of the bluescreens seem to come from driver issues. All drivers are up to date. I'm afraid that my memory is broken or the mainboard or both. I used the windows integrated memtest which didn't find any errors. Memtest86 found some errors. Does it make sense to buy new memory? Couldn't it be a problem of the board as well? I also read that my memory could run at a too low voltage. But it's set to 1.5V as recommended. Another guess would be to set the memory's latencies manually, but how do I know which ones to try? Here is a screenshot of bluescreenview showing the latest bluescreens. Maybe someone has faced the same behavior before and found a solution. Any ideas or suggestions? Current setup on which the bluescreens occur. Windows 8 RTM (6.2.9200) Asrock 970 Extreme4 AMD FX-8150 ATI Radeon HD5850 16 GB RAM (DDR3-1800) Latest drivers for all devices

  Read the article

• Ubuntu: Network connection seems to fail after some time

  - by chrischu

  I just bought a Shuttle XS-35 barebone mini-PC and put a 1 TB WD hard drive and 2 Gigs of RAM into it and installed Ubuntu onto it. The machine will post as a media server (streaming videos to my PS3) and as a webserver for some small private projects. Now I wanted to copy my videos from my Windows 7 machine to the Ubuntu machine and therefore created a Samba share on the Ubuntu machine. I tried copying the files with the standard Windows copy function and with SyncToy but after some time (sometimes 5 copied files, sometimes 120 copied files) the Samba share just disappears. When that happens I can't reach the internet from the Ubuntu machine although the network connection still seems to be fine (IP still there etc.). Between the machines lies a LinkSys router. When I try to ping my router (after the connection doesn't work anymore) from the Ubuntu machine only a very small subset of the packages actually get there (something around 20%). When I restart the Ubuntu machine everything seems to work normal again. I have no idea where the problem lies here. Does anybody have a clue? Thanks in advance!

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >